Precipitation and fracture behaviour of Fe–Mn–Ni–Al alloys

The effects of Al addition on the precipitation and fracture behaviour of Fe–Mn–Ni alloys were investigated. With the increasing of Al concentration, the matrix and grain boundary precipitates changed from L1₀ θ-MnNi to B2 Ni₂MnAl phase, which is coherent and in cube-to-cube orientation relationship with the α′-matrix. Due to the suppression of the θ-MnNi precipitates at prior austenite grain boundaries (PAGBs), the fracture mode changed from intergranular to transgranular cleavage fracture. Further addition of Al resulted in the discontinuous growth of Ni₂MnAl precipitates in the alloy containing 4.2?wt.% Al and fracture occurred by void growth and coalescence, i.e. by ductile dimple rupture. The transition of the fracture behaviour of the Fe–Mn–Ni–Al alloys is discussed in relation to the conversion of the precipitates and their discontinuous precipitation behaviour at PAGBs.     

ICEMS study of isothermal oxidation of Fe–Mn–Al–C–Cr–Si–Mo, Fe–Mn–Al–C–Cr–Si and Fe–9Cr–1Mo alloys

The purpose of this paper is to investigate the isothermal behavior of Fe–27.3Mn–7.6Al–C–6.5Cr–0.25Si–0.88Mo (Mo(0)) and Fe–27.3Mn–7.6Al–1.0C–6.5Cr–0.25Si (Mo(1)) alloys and compare it against Fe–9Cr–1Mo (FCR) commercial alloy. The experiments were carried out at 600°C, 700°C, 750°C and 850°C, each one during 72 h in static air. The oxidation kinetics was measured as a function of time using a Thermogravimetry analyzer (TGA). The structure and composition of the oxide scale were characterized by X-ray diffraction (XRD) and Integral Conversion Electron Mössbauer Spectroscopy (CEMS). The TGA results show that at all oxidation temperatures the sample FCR exhibit the lowest kinetic corrosion and the lowest weight gain, whereas Mo(0) the highest. By CEMS technique it were found a broad magnetic sextet, which has been fit by one hyperfine field distribution with mean hyperfine field characteristic to ferritic/martensite phase, one Fe^3?+? doublet and one singlet for the Mo(0) and Mo(1) alloys. Samples oxidized at highest temperatures exhibit a strong paramagnetic line, probably due that the Cr or Mn oxides may be enriched on the surface. Then, the magnetic phase can be converted partially into austenite phase at highest temperatures.     

Annealing texture of a cold-rolled Fe–Mn–Al–Si–C alloy

The study of recrystallization texture of a cold deformed Fe–Mn–Al–Si–C alloy, with about 30% Mn, has been discussed in this paper. The alloy is fully austenitic at room temperature, and therefore, principal FCC rolling textures were developed in this material at different stages of cold rolling. The present study was undertaken to observe the transformation of FCC rolling texture during recrystallization of a heavily cold deformed specimen. It was observed that isothermal annealing at 750 °C led to a weak recrystallisation texture, which was quite similar to the deformation texture developed at the early stage of cold rolling. During recovery stage, a strong Bs/Goss-type texture was developed, which was identified as a new observation in this work.     

Magnetic phase diagrams of Fe–Mn–Al alloy on the Bethe lattice

The magnetic behaviors of the Fe–Mn–Al alloy are simulated on the Bethe lattice by using a trimodal random bilinear exchange interaction(J) distribution in the Blume–Capel(BC) model. Ferromagnetic(J 0) or antiferromagnetic(J 0)bonds or dilution of the bonds(J = 0) are assumed between the atoms with some probabilities. It is found that the secondor the first-order phase boundaries separate the ferromagnetic(F), antiferromagnetic(AF), paramagnetic(P), or spin-glass(SG) phases from the possible other one. In addition to the tricritical points, the special points at which the second- and the first-order and the spin-glass phase lines meet are also found. Very rich phase diagrams in agreement with the literature are obtained.     

α- and β-Mn precipitates in the spinodal Fe30Ni20Mn25Al25 alloy

Precipitates in the spinodal alloy Fe₃₀Ni₂₀Mn₂₅Al₂₅, produced by drop-casting followed by hot extrusion, have been investigated using transmission electron microscopy. The as-extruded microstructure consisted of alternating, coherent body-centred cubic and B2 (ordered body-centred cubic) rods aligned along ?100? directions with a wavelength of ～60?nm. Upon annealing at 550°C, precipitates were formed having two distinct morphologies: relatively spherical precipitates with the α-Mn crystal structure and more elongated precipitates with the β-Mn crystal structure. Both precipitates existed simultaneously after annealing at this temperature for up to at least 99?h. The compositions of the precipitates and the orientation relationships between the precipitates and the spinodal matrix were determined.     

Modeling the TDFD dissolution of Al–Fe–Mn–Si particles in an Al–4.5Zn–1Mg alloy

Dissolution of large particles in DC-cast 7xxx aluminum alloys is one of the primary objectives of the homogenization process. A mathematical model to describe and predict this complex thermodynamical and kinetical process is of great significance. In this paper, the details of a diffusion-limited dissolution model, based on the thinning, discontinuation and full dissolution (TDFD) mechanism, to predict the dissolution of the Al₁₇(Fe_3.2, Mn_0.8)Si₂ particles is described. The model is capable of predicting the volume fraction and thickness of the particles during homogenization at different temperatures and time intervals. The predicted results are in good agreement with measurements using quantitative X-ray diffraction (QXRD) and quantitative field emission gun-scanning electron microscopy (QSEM). The model predictions of the supersaturation parameter, interface position, interface movement rate of the planar surfaces and the cylindrical edges, and the effect of the occurrence of discontinuities on the dissolution extent are presented.     

Simulation of displacement cascades in Ni–Al ordered alloys

Abstract

Molecular dynamics was used to investigate defect production induced by displacement cascades in ordered intermetallic alloys NiAl and Ni₃Al. The composite potentials obtained from the embedded atom potentials (EAM) and the universal function of Biersack and Ziegler were used. The number of point defects and their final structure produced by displacement cascades were investigated and compared with the standard NRT prediction. Crystalline structure, atomic mixing and chemical disordering were also studied during the evolution of the cascades, by measuring their characteristic parameters in the cells of the subdivided crystal.     

Fe–Mn–Al–C Alloys: a Study of Their Corrosion Behaviour in SO2 Environments

The corrosion reaction of four Fe–Mn–Al alloys exposed to a cycling, dry–humid, SO₂ (0.001% by volume) polluted atmosphere was studied. ICEMS, XPS, AES-SAM and transmission Mössbauer spectroscopy at different temperatures were employed to characterize the corrosion products. The analytical results indicate that (i) ferrihydrite is the main component of the rust; (ii) there is an abundant presence of Mn²⁺ and SO₃ ^2–/SO₄ ^2– on the top of the corrosion layer, the concentration of SO₄ ^2– increasing with the number of cycles; and (iii) the magnetic hyperfine pattern exhibited by the series of low-temperature spectra of the rust is quite different from that observed in the rust formed under similar corrosive environments on iron and weathering steel. This latter finding is correlated with a slow rate of transformation of the Fe³⁺ species formed at the early stages of corrosion into -FeOOH, the usual final product of this type of corrosion processes. The sulphate anions, abundant inside the electrolyte during the wet periods, could be incorporated to the ferrihydrite structure being responsible for the Mössbauer spectral pattern recorded from the corrosion products at low temperatures.     

TEM investigation of the formation mechanism of deformation twins in Fe–Mn–Si–Al TWIP steels

The microstructure of a Fe–Mn–Si–Al twinning-induced plasticity (TWIP) steel exhibiting remarkable work hardening rate under uniaxial tensile deformation was investigated using transmission electron microscopy to uncover the mechanism(s) controlling the nucleation and growth of the mechanically induced twins. The results show that the stair-rod cross-slip deviation mechanism is necessary for the formation of the twins, while large extrinsic stacking faults homogenously distributed within the grains could act as preferential sources for the activation of the deviation process. The influence of such features on the thickness and strength of the twins and the resulting mechanical behaviour is discussed and compared to similar works recently performed on Fe–Mn–C TWIP steels.     

Stability,electronic structures,and mechanical properties of Fe–Mn–Al system from first-principles calculations

The stability, electronic structures, and mechanical properties of the Fe–Mn–Al system were determined by firstprinciples calculations. The formation enthalpy and cohesive energy of these Fe–Mn–Al alloys are negative and show that the alloys are thermodynamically stable. Fe_3Al, with the lowest formation enthalpy, is the most stable compound in the Fe–Mn–Al system. The partial density of states, total density of states, and electron density distribution maps of the Fe–Mn–Al alloys were analyzed. The bonding characteristics of these Fe–Mn–Al alloys are mainly combinations of covalent bonding and metallic bonds. The stress-strain method and Voigt–Reuss–Hill approximation were used to calculate the elastic constants and moduli, respectively. Fe_(2.5)Mn_(0.5)Al has the highest bulk modulus, 234.5 GPa. Fe_(1.5)Mn_(1.5)Al has the highest shear modulus and Young's modulus, with values of 98.8 GPa and 259.2 GPa, respectively. These Fe–Mn–Al alloys display disparate anisotropies due to the calculated different shape of the three-dimensional curved surface of the Young's modulus and anisotropic index. Moreover, the anisotropic sound velocities and Debye temperatures of these Fe–Mn–Al alloys were explored.     

Electrical Resistivity of Liquid Fe–Mn Alloys

Russian Physics Journal - The paper deals with the specific electrical resistivity of liquid Fe–Mn alloys with the manganese content of 3.9, 6.0, 8.2, 10.3 and 13.2 at.%. A rotary-field...     

Decagonal quasicrystal in the Al–Pd–Mn system

Abstract

A stable decagonal quasicrystal in Al₇₀Pd_30?xMn_x alloys (x = 10–20) was examined by electron diffraction and high-resolution electron microscopy. The decagonal quasicrystalline grains are formed with definite crystallographic relationships to adjacent icosahedral and Al₃Mn crystalline grains. The structure of the decagonal phase, which is formed as the main phase at near Al₇₀Pd₁₀Mn₂₀ composition, is a mixture of decagonal quasicrystalline regions with some linear phason strain and microcrystalline regions. The structures of both regions may be interpreted in terms of quasiperiodic and periodic tilings, constructed with two types of bond lengths, S (about 2 nm) and L (= τ · S, where τ is the Golden ratio), of the same atom cluster with decagonal symmetry.     

Phonon- and phason-dynamics in Al–Cu–Fe quasicrystals

The lattice dynamics of quasicrystals includes local phason jumps as well as phonons. Phason dynamics is important for the understanding of both the structure and atomic motion in quasicrystals, leading to short-ranged atomic motion not involving vacancies in addition to diffusion. We have studied the phason and phonon dynamics of icosahedral i-Al₆₂Cu_25.5Fe_12.5. Quasielastic Mössbauer spectroscopy (QMS) was used to probe the iron phason dynamics. Inelastic nuclear-resonant absorption (INA) of synchrotron radiation and inelastic neutron scattering (INS) were used to study the iron-partial as well as the total vibrational DOS (VDOS). We find from preliminary QMS studies that iron atoms jump on a time scale about two orders of magnitude slower than that found for copper. The EFG shows an abrupt change in slope at ca. 825 K which may be related to a transition from simple (isolated) to more complicated (co-operative) phason jumps. From INA we find that the iron-partial VDOS differs radically from that of the total (neutron-weighted) generalised VDOS measured by INS. Both these properties are related to the specific local environments of Fe and Cu in i-AlCuFe.     

Electron irradiation-enhanced core/shell organization of Al(Cr,Fe, Mn)Si dispersoids in Al–Mg–Si alloys

The age hardening 6061-T6 aluminium alloy has been chosen as structural material for the core vessel of the material testing Jules Horowitz nuclear reactor. The alloy contains incoherent Al(Cr, Fe, Mn)Si dispersoids whose characterization by energy-filtered transmission electron microscopy (EFTEM) analysis shows a core/shell organization tendency where the core is (Mn, Fe) rich, and the shell is Cr rich. The present work studies the stability of this organization under irradiation. TEM characterization on the same particles, before and after 1 MeV electron irradiation, reveals that the core/shell organization is enhanced after irradiation. It is proposed that the high level of point defects, created by irradiation, ensures a radiation-enhanced diffusion process favourable to the unmixing forces between (Fe, Mn) and Cr. Shell formation may result in the low-energy interface segregation of Cr atoms within the (Fe, Mn) system combined with the unmixing of Cr, Fe and Mn components.     

Deformation-induced atomic redistribution in bcc Fe–Mn alloy

Deformation-induced iron and manganese atomic separation in a bcc solid solution is detected via Mössbauer spectroscopy in Fe_93.2Mn_6.8 alloy after high pressure torsion deformation in Bridgman anvils. The rate of short-range separation grows along with the temperature of deformation.     

Hyperfine Study on Mechanically Alloyed Fe–Mn Systems

Hyperfine Interactions - High-energy ball milling of Fe–Mn elemental powder mixtures has been carried out for different Mn concentrations, ranging from 0 to 90%. Mössbauer spectroscopy...     

In-situ study of precipitates in Al–Zn–Mg–Cu alloys using anomalous small-angle x-ray scattering

In the present work,the precipitate compositions and precipitate amounts of these elements(including the size distribution,volume fraction,and inter-precipitate distance) on the Cu-containing 7000 series aluminum alloys(7150 and 7085 Al alloys),are investigated by anomalous small-angle x-ray scattering(ASAXS) at various energies.The scattering intensity of 7150 alloy with T6 aging treatment decreases as the incident x-ray energy approaches the Zn absorption edge from the lower energy side,while scattering intensity does not show a noticeable energy dependence near the Cu absorption edge.Similar results are observed in the 7085 alloy in an aging process(120℃) by employing in-situ ASAXS measurements,indicating that the precipitate compositions should include Zn element and should not be strongly related to Cu element at the early stage after 10 min.In the aging process,the precipitate particles with an initial average size of ~ 8 ?A increase with aging time at an energy of 9.60 ke V,while the increase with a slower rate is observed at an energy of 9.65 ke V as near the Zn absorption edge.     

Microstructural evolution in Al–Mn–Cu–(Be) alloys

This study investigates the effects of alloying elements on the microstructural evolution of Al-rich Al–Mn–Cu–(Be) alloys during solidification, and subsequent heating and annealing. The samples were characterised using scanning electron microscopy, energy dispersive X-ray spectroscopy, synchrotron X-ray diffraction, time-of-flight secondary-ion mass spectroscopy, and differential scanning calorimetry. In the ternary Al₉₄Mn₃Cu₃ (at%) alloy, the phases formed during slower cooling (≈1?K?s^?1) can be predicted by the known Al–Mn–Cu phase diagram. The addition of Be prevented the formation of Al₆Mn, decreased the fraction of τ₁-Al₂₉Mn₆Cu₄, and increased the fraction of Al₄Mn. During faster cooling (≈1000?K?s^?1), Al₄Mn predominantly formed in the ternary alloy, whereas, in the quaternary alloys, the icosahedral quasicrystalline phase dominated. Further heating and annealing of the alloys caused an increase in the volume fractions of τ₁ in all alloys and Be₄Al (Mn,Cu) in quaternary alloys, while fractions of all other intermetallic phases decreased. Solidification with a moderate cooling rate (≈1000?K?s^?1) caused considerable strengthening, which was reduced by annealing for up to 25% in the quaternary alloys, while hardness remained almost the same in the ternary alloy.