Effects of thermal oxidation on the photoluminescence properties of porous silicon

The effects of thermal oxidation on the photoluminescence (PL) properties of powdered porous silicon (PSi) are studied using X-ray photoelectron spectroscopy (XPS). It is found that the PL intensity is steeply quenched after annealing at and recovered at above . The XPS intensity of oxides formed on the PSi surface is also found to strongly depend on the annealing temperature. The comparison between the annealing temperature dependence of PL intensity and that of the oxide XPS intensity suggests that the formation of thin disordered SiO₂ layer accompanies the quenching of the PL intensity, and that the formation of thick high-quality SiO₂ layer results in the PL intensity recovery. These results indicate that the thickness and quality of SiO₂ layer play a crucial role in the PL properties of thermally oxidized PSi.     

Effect of rapid thermal treatment on photoluminescence of surface passivated porous silicon

The photoluminescence of porous silicon with and without carbon deposition fabricated by plasma-enhanced chemical vapor deposition technique has been investigated. After the deposition, the rapid thermal processes in the temperature ranging from 500 to 1100 °C have been carried out. It was found that after the carbon deposition a new intense blue emission appeared. The rapid thermal processes at 800and 900 °C could enhance the blue emission, while the other rapid thermal processes quenched it. Finally, the mechanism for the effect of carbon deposition and rapid thermal processes on photoluminescence properties of porous silicon was discussed.     

水蒸气退火多孔硅发光性能的正电子谱学研究

使用正电子湮没寿命谱和正电子寿命-动量关联谱对水蒸气和真空条件下退火的多孔硅样品的微观缺陷结构进行表征,结合发射光谱测量结果,对影响多孔硅发光性能的因素进行了讨论.实验结果表明,水蒸气退火后样品孔壁表面的悬挂键减少,并出现新的E′γ和EX类缺陷.水蒸气退火后样品中两种缺陷数量发生变化是导致多孔硅样品发光增强的直接原因;真空退火未使样品中发光相关缺陷发生变化,样品的发光性能没有显著改变.     

有机吸附物对多孔硅微腔发光的影响

理论上,采用Bruggeman有效介质近似,研究了有机吸附物对多孔硅微腔的折射率及其光致发光谱的影响.实验上,采用计算机控制的电化学腐蚀法制备了多孔硅微腔样品,并利用机械泵油的蒸气分子与该微腔样品进行相互作用.研究发现,多孔硅微腔发射的窄化光致发光谱对泵油蒸气分子的吸附与脱附很敏感,与之伴随的是该窄化光致发光谱发生明显的峰位移动(可达71nm)和强度变化.结合Bruggeman近似和表面态对多孔硅发光的影响,对实验结果进行了定性解释.实验结果与理论模拟结果符合较好. 关键词： Bruggeman近似 吸附物 多孔硅微腔 光致发光谱     

Effects of selenium treatment on composition and photoluminescence properties of porous silicon

In this work, an ultrasonically enhanced anodic electrochemical etching is developed to fabricate light-emitting porous silicon material. Porous silicon layer is fabricated in n-type (1 0 0) oriented silicon using HF solution and treated in selenious acid to increase the photoluminescence intensity. It is found that the increase of photoluminescence intensity after selenious acid treatment is higher in the intact zones and lower in the detached zones of ultrasonic excitation. The photoluminescence appears as a non-monotonous function of time exposure of selenious acid treatment. Surface chemical composition analysis by X-ray photoelectron spectroscopy shows formation of Si-Se_x and Si-Se_x-O_y on the surface of porous silicon treated with the selenious acid.     

多孔硅的时间延迟光谱

利用时间延迟光谱技术测量了多孔硅的发光光谱. 实验结果表明,多孔硅的发光是复杂的动力学发光弛豫过程,时间延迟光谱测量技术在研究复杂动力学发光过程方面比稳态光谱测量方法更有效.     

Instability of the photoluminescence of porous silicon

Results of studies of the photoluminescence of porous silicon with different prehistories have revealed the mechanism and nature of the instability of the luminescence properties of freshly prepared samples. It was established that the initial quenching and subsequent rise of the photoluminescence is attributable to the intermediate formation of silicon monoxide (photoluminescence degradation) and subsequent additional oxidation to form SiO₂ (photoluminescence rise). Ultraviolet laser irradiation accelerates this process by a factor of 200–250 compared with passive storage of the samples in air. Plasma-chemical treatment in an oxygen environment merely results in a subsequent rise in the photoluminescence as a result of the formation of monoxide on the porous silicon surface. A kinetic model is proposed for this process. Zh. Tekh. Fiz. 69, 135–137 (June 1999)     

Stable blue-green and ul traviolet photoluminescence from silicon carbide on porous silicon

β-Silicon carbide layers have been prepared by high temperature pyrolysis of polyimide Langmuir-Blodgett films on porous silicon substrate in vacuum. The formation of silicon carbide is confirmed by the IR and XRD spectra. It is found that photoluminescence still exists and appears in the blue-green and ultraviolet regions after thermal treatment at 900°C. These results indicate that the silicon carbide layers, which are formed, are responsible for the blue-green luminescence.     

Influence of LiBr on photoluminescence properties of porous silicon

A new method has been developed to improve the photoluminescence intensity of porous silicon (PS), which is first time that LiBr is used for passivation of PS. Immersion of the PS in a LiBr solution, followed by a thermal treatment at 100 °C for 30 min under nitrogen, leads to a nine fold increase in the intensity of the photoluminescence. The atomic force microscope (AFM) shows an increase of the nanoparticle dimension compared to the initial dimension of the PS nanostructure. The LiBr covers the nanoparticles of silicon without changing the wavelength distribution of the optical excitation and emission spectra. Moreover, a significant decrease of reflectivity was observed for the wavelength in the range of 350-500 nm.     

Influence of natural aging on photoluminescence from porous silicon

The influence of natural aging on the photoluminescence intensity and the position of a photolu-minescence peak in n-type por-Si (por-Si) is studied. The variation of the phase composition and the relative content of the amorphous and oxide phases of silicon in por-Si during aging is determined by fitting simulated spectra to experimental ultrasoft Si L _2,3 X-ray emission spectra using reference spectra.     

Photoluminescent properties of silicon carbide and porous silicon carbide after annealing

Photoluminescent (PL) p-type 6H porous silicon carbides (PSCs), which showed a strong blue-green photoluminescence band centered at approximately 490 nm, were annealed in Ar and vacuum conditions. The morphological, optical, and chemical states after annealing are reported on electrochemically etched SiC semiconductors.The thermal treatments in the Ar and vacuum environments showed different trends in the PL spectra of the PSC. In particular, in the case of annealing in a vacuum, the PL spectra showed both a weak red PL peak near 630 nm and a relatively intense PL peak at around 430 nm in the violet region. SEM images showed that the etched surface had spherical nanostructures, mesostructures, and islands. With increasing annealing temperature it changes all spherical nanostructures. The average pore size observed at the surface of the PSC before annealing was of the order of approximately 10 nm.In order to investigate the surface of a series of samples in detail, both the detection of a particular chemical species and the electronic environments at the surface are examined using X-ray photoelectron spectroscopy (XPS). The chemical states from each XPS spectrum depend differently before and after annealing the surface at various temperatures. From these results, the PL spectra could be attributed not only to the quantum size effects but also to the oxide state.     

Stable ultraviolet photoluminescence emission in n-type porous silicon

This very paper is focusing on the investigation of porous silicon preparation with n-type silicon wafer by means of electrochemical anodization in the dark and, particularly, on its stable ultraviolet photoluminescence emission. A lateral electrical potential was applied, for this purpose, on silicon wafers, driving the electrons away and letting holes appear on the surface of the silicon wafer to enhance the electrochemical etching process. Characterizations have been made with scanning electronic microscope, fluorescence spectrophotometer and Fourier transform infrared spectroscope. An ultraviolet photoluminescence emission of 370 nm is found in the as-prepared n-type porous silicon, which seems to be well associated with the formation of oxygen-related species (twofold coordinated silicon defect) during the anodic oxidation. The result characterized by photo-bleaching performance indicates that the ultraviolet photoluminescence emission is so stable—only 7% reduction within 3600 s. Meanwhile the morphology of as-prepared n-type porous silicon is investigated.     

稀土掺杂多孔硅的蓝光发射

关键词：     

Laser on porous silicon after oxidation by irradiation and annealing

Stimulated emission has been observed from oxide structure of silicon when optically excited by 514 nm laser. The photoluminescence (PL) pulse has a Lorentzian shape with a full width at half maximum (FWHM) of 0.5-0.6 nm. The twin peaks at 694 nm and 692 nm are dominated by stimulated emission which can be demonstrated by its threshold behavior and transition from sub-threshold to linear evolution in light emission. The gain coefficient from the evolution of the peak-emission intensity as a function of the optically pumped sample length has been measured. The oxide structure was fabricated by laser irradiation and annealing treatment on silicon. A model for explaining the stimulated emission has been proposed in which the trap states of the interface between oxide of silicon and porous nanocrystal play an important role.     

Depth dependence of photoluminescence and chemical bonding in porous silicon

Porous silicon (PS) is studied by stepwise peeling of the surface layer to clarify the non-uniformity in the photoluminescence (PL) and correlate it with the in-depth chemical bonding and structure of the 30 μm thick layer. The PL intensity grows by an order of magnitude after the peeling off of the first 10 μm and decreases five times in the next 5 μm while the peak maximum position shifts from 730 to 800 nm. X-ray photoelectron spectroscopy (XPS) measurements show that Si–Si and Si–O bonds are present both on the surface and below, and the preferential oxidation state of silicon changes from 3+ and 4+ on the surface to 1+ and 2+ below 10 μm. Using Raman spectroscopy silicon nanocrystals are shown to exist. Their mean size can be estimated at about 3 nm. These results show that the strongest PL comes from a region in the PS layer where silicon nanocrystallites are surrounded by oxides with a low level of oxidation and not from the strongly oxidized surface layer.     

Tunable photoluminescence of porous silicon by liquid crystal infiltration

The photoluminescence (PL) of porous silicon films has been investigated as a function of the amount of liquid crystal molecules that are infiltrated into the constricted geometry of the porous silicon films. A typical nematic liquid crystal 4-pentyl-4′-cyanobiphenyl was employed in our experiment as the filler to modify the PL of porous silicon. It is found that the originally red PL of porous silicon films can be tuned to blue by simply adjusting the amount of liquid crystal molecules in the microchannels of the porous films. The chromaticity coordinates are calculated for the recorded PL spectra. The mechanism of the tunable PL is discussed. Our results have demonstrated that the luminescent properties of porous silicon films can be efficiently tuned by liquid crystal infiltration.     

Long-time stabilization of porous silicon photoluminescence by surface modification

We present results on the photoluminescence (PL) properties of porous silicon (PS) as a function of time. Stabilization of PL from PS has been achieved by replacing silicon-hydrogen bonds terminating the surface with more stable silicon-carbon bonds. The composition of the PS surface was monitored by transmission Fourier transform infrared (FTIR) spectroscopy at intervals of 1 month in ageing time up to 1 year. The position of the maximum PL peak wavelength oscillates between a blue-shift and a red-shift in the 615-660 nm range with time.