Effect of Sn and Al additions on the microstructure and mechanical properties of amorphous Ti–Cu–Zr–Ni alloys

Amorphous Ti–Cu–Zr–Ni alloys with minor addition of Sn and Al were prepared by melt spinning technique.The effects of Sn and Al additions on the microstructures and mechanical properties of glassy ribbons were investigated.The amorphous state of ribbons was confirmed by x-ray diffraction and transmission electron microscopy,where those ribbons with Sn addition exhibited a fully amorphous state.The characteristic temperature indicates that Ti_(45)Cu_(35)Zr_(10)Ni_5Sn_5 alloy has a stronger glass-forming ability,as proven by differential scanning calorimetry.Ti_(45)Cu_(35)Zr_(10)Ni_5Al_5 alloy showed a better hardness of 9.23 GPa and elastic modulus of 127.15 GPa and good wear resistance.Ti_(45)Cu_(35)Zr_(10)Ni_5Sn_5 alloy displayed a pop-in event related to discrete plasticity according to nanoindentation.When the temperature is below 560 K,Ti_(45)Cu_(35)Zr_(10)Ni_5Sn_5 alloy mainly exhibits elasticity.When the temperature rises between 717 K and 743 K,it shows a significant increase in elasticity but decrease in viscoelasticity after the ribbon experiences the main relaxation at 717 K.When the temperature is above 743 K,the ribbon shows viscoplasticity.     

Zr and Hf microalloying in an Al–Y–Fe amorphous alloy. Relation between local structure and glass-forming ability

The effects of the addition of small amounts of Zr and Hf (0.5–3%) on the atomic structure of Al₈₈Y₇Fe₅ metallic glass were examined from extended X-ray absorption fine structure (EXAFS) experiments to better understand the influence of these microadditions on the glass-forming ability of this alloy. Measurements at the Zr K and Hf LIII absorption edges allowed the local structures around Zr and Hf atoms to be determined. The same Al environment was found for the different concentrations, consisting of a small cluster extending up to 4.5 Å around the Zr atoms and up to 6 Å around the Hf ones. Although the clustering effect is smaller in the Zr neighbourhood, a drastic shortening of the nearest Zr–Al distance is shown, providing evidence for some covalent character to the bonding, in line with the increased glass-forming ability found in the alloys made with the Zr microaddition.     

The characterisation of atomic structure and glass-forming ability of the Zr–Cu–Co metallic glasses studied by molecular dynamics simulations

In the present work, the glass formation process and structural properties of Zr₅₀Cu_50-xCo_x (0 ≤ x ≤ 50) bulk metallic glasses were investigated by a molecular dynamics simulation with the many body tight-binding potentials. The evolution of structure and glass formation process with temperature were discussed using the coordination number, the radial distribution functions, the volume–temperature curve, icosahedral short-range order, glass transition temperature, Voronoi analysis, Honeycutt–Andersen pair analysis technique and the distribution of bond–angles. Results indicate that adding Co causes similar responses on the nature of the Zr₅₀Cu_50-xCo_x (0 ≤ x ≤ 50) alloys except for higher glass transition temperature and ideal icosahedral type ordered local atomic environment. Also, the differences of the atomic radii play the key role in influencing the atomic structure of these alloys. Both Cu and Co atoms play a significant role in deciding the chemical and topological short-range orders of the Zr₅₀Cu_50-xCo_x ternary liquids and amorphous alloys. The glass-forming ability of these alloys is supported by the experimental observations reported in the literature up to now.     

Effect of oxygen partial pressure on the structure and properties of Cu–Al–O thin films

We have studied the electrical and optical properties of Cu–Al–O films deposited on silicon and quartz substrates by using radio frequency (RF) magnetron sputtering method under varied oxygen partial pressure P_O. The results indicate that P_O plays a critical role in the final phase constitution and microstructure of the films, and thus affects the electrical resistivity and optical transmittance significantly. The electrical resistivity increases with the increase of P_O from 2.4 × 10^?4 mbar to 7.5 × 10^?4 mbar and afterwards it decreases with further increasing P_O up to 1.7 × 10^?3 mbar. The optical transmittance in visible region increases with the increase of P_O and obtains the maximum of 65% when P_O is 1.7 × 10^?3 mbar. The corresponding direct band gap is 3.45 eV.     

Effects of Re microalloying on glass formation and mechanical properties of Zr–Cu–Al alloys

The effect of microalloying with rhenium on a metallic glass-forming alloy (Cu₄₆Zr₄₆Al₈)_{100? x} Re _x (x?=?1,?2) was investigated. Re possesses a positive enthalpy of mixing within the Cu–Re terminal system. Splat quenched foils of ≈40?µm in thickness display an amorphous structure. Their crystallisation temperature increases from T _x?=?504 to 513°C with addition of Re at nearly constant glass formation temperature T _g?=?445°C for the amorphous samples. In contrast, injection cast rods consist of B2-CuZr type phase dendrites, minor fractions of a cubic phase CuZrAl, and randomly distributed small particles of a Re-rich phase. This represents a novel concept in microalloying where Re-rich precipitates trigger the B2 phase formation. It leads to a unique combination of mechanical properties for as-cast rods, which display high strength at sizeable plastic deformation up to ε _p?≈?4% and an extended range of work-hardening prior to failure.     

Effect of copper on the structure–phase transformations and the properties of quasi-binary TiNi–TiCu alloys

The effect of copper alloying up to 25 at % on the structure–phase transformations and the physicomechanical properties of ternary alloys from the quasi-binary TiNi–TiCu section is studied by measuring the physicomechanical properties, transmission electron microscopy, scanning electron microscopy, electron diffraction, and X-ray diffraction (XRD). The data of temperature measurements of the electrical resistivity and the magnetic susceptibility and XRD data are used to plot a general diagram for the thermoelastic B2 ? B19', B2 ? B19 ? B19', and B2 ? B19 martensitic transformations, which occur in the alloys upon cooling as the copper content increases in the ranges 0–8, 8–15, and 15–25 at % Cu, respectively. The experimental results are compared to the well-known data, including differential scanning calorimetry data, obtained for these alloys. The changes in the mechanical properties and the microstructure of the alloys in the state of B19 or B19' martensite are discussed.     

Effect of growth rate and Mg content on dendrite tip characteristics of Al–Cu–Mg ternary alloys

An experimental analysis is presented to correlate the secondary dendrite arm spacing λ ₂ and dendrite tip radius R with growth rate V and Mg content C _0-Mg of Al–Cu–Mg ternary alloys. Under constant temperature gradient G (4.84±0.13 K mm⁻¹), a series of directional solidification experiments were performed at five different growth rates V (16.7–83.3 μm/s) and five different Mg contents C _0-Mg in Al–5 wt.% Cu–(0.5–5) wt.% Mg alloys. Solid–liquid interface was investigated from the longitudinal sections of the quenched samples, and λ ₂ and R were measured on the dendrite tips. The dependencies of λ ₂ and R on V and C _0-Mg were determined. The experimental results showed that the values of λ ₂ and R decrease as V and C _0-Mg increase at a constant G. The present exponent values related to V are found to be slightly lower than the values of the theoretical models and previous experimental works; however, C _0-Mg exponent values are found to be much lower than the theoretical models and previous experimental works. The ratio of the secondary dendrite arm spacing to the dendrite tip radius is 2.09±0.15, in good agreement with the scaling law. At a constant C _0-Mg, the values of VR ² were found to slightly increase with the ascending V. However, as C _0-Mg increases, the values of VR ² decrease.     

Effect of thermal cycling on structure and properties of Ni–Mn–In-based alloys

Technical Physics - The results of investigations of the structure and properties of ternary alloys Ni47–x Mn42 + x In11 (0 ≤ x ≤ 2) after thermal cycling are presented. It has...     

Formation of the structure and physicomechanical properties of a quasicrystalline Al–Cu–Fe alloy upon plasma spraying

Quasicrystalline coatings prepared under various thermal conditions of spraying have been studied. Initial quasicrystalline powders with dispersion of 10–50 μm were prepared in a low-pressure arc discharge plasma. The coatings have been sprayed on copper rings using a swinging plasmatron. It is found that the increase in the quenching rate of melt droplets increases the chemical homogeneity and leads to formation of nanostructured formations. The precipitation of nanostructured grains (d < 100 nm) in the sprayed alloy leads to an increase in the mechanical characteristics (hardness, deformation, and ductility) and can be considered as an additional factor of hardening of the material.     

Influence of Cd addition on the phase transformations of β Cu–Al alloys

Cu–Al alloys in the hyper- and hypoeutectoid region with addition of Cd are studied. The phase transformation sequence during continuous heating and cooling has been followed by resistometry, calorimetry, and optical microscopy.     

Simulated Cu–Zr glassy alloys: the impact of composition on icosahedral order

The structural properties of the simulated Cu_αZr_1-α glassy alloys are studied in the wide range of the copper concentration to clarify the impact of the composition on the number density of the icosahedral clusters. Both bond orientational order parameters and Voronoi tessellation methods are used to identify these clusters. Our analysis shows that abundance of the icosahedral clusters and the chemical composition of these clusters are essentially nonmonotonic versus and demonstrate local extrema. That qualitatively explains the existence of pinpoint compositions of high glass-forming ability observing in Cu Zr alloys. Finally, it has been shown that Voronoi method overestimates drastically the abundance of the icosahedral clusters in comparison with the bond orientational order parameters one.     

Effect of gallium alloying on the structure,the phase composition,and the thermoelastic martensitic transformations in ternary Ni–Mn–Ga alloys

The effect of gallium alloying on the structure, the phase composition, and the properties of quasibinary Ni₅₀Mn_50–zGa_z (0 ? z ? 25 at %) alloys is studied over a wide temperature range. The influence of the alloy composition on the type of crystal structure in high-temperature austenite and martensite and the critical martensitic transformation temperatures is analyzed. A general phase diagram of the magnetic and structural transformations in the alloys is plotted. The temperature–concentration boundaries of the B2 and L2₁ superstructures in the austenite field, the tetragonal L1₀ (2M) martensite, and the 10M and 14M martensite phases with complex multilayer crystal lattices are found. The predominant morphology of martensite is shown to be determined by the hierarchy of the packets of thin coherent lamellae of nano- and submicrocrystalline crystals with planar habit plane boundaries close to {011}_B2. Martensite crystals are twinned along one of the 24 \(24\left\{ {011} \right\}{\left\langle {01\bar 1} \right\rangle _{B2}}\) “soft” twinning shear systems, which provides coherent accommodation of the martensitic transformation–induced elastic stresses.     

Effect of Ni and vacancy concentration on initial formation of Cu precipitate in Fe–Cu–Ni ternary alloys by molecular dynamics simulation

In the present work, the effects of Ni atoms and vacancy concentrations(0.1%, 0.5%, 1.0%) on the formation process of Cu solute clusters are investigated for Fe–1.24%Cu–0.62%Ni alloys by molecular dynamics(MD) simulations. The presence of Ni is beneficial to the nucleation of Cu precipitates and has little effect on coarsening rate in the later stage of aging. This result is caused by reducing the diffusion coefficient of Cu clusters and the dynamic migration of Ni atoms. Additionally, there are little effects of Ni on Cu precipitates as the vacancy concentration reaches up to 1.0%,thereby explaining the embrittlement for reactor pressure vessel(RPV) steel. As a result, the findings can hopefully provide the important information about the essential mechanism of Cu cluster formation and a better understanding of ageing phenomenon of RPV steel. Furthermore, these original results are analyzed with a simple model of Cu diffusion, which suggests that the same behavior could be observed in Cu-containing alloys.     

Magnetic hysteretic characterization of the irradiation-induced embrittlement of Fe,Fe–Cu model alloys,and reactor pressure vessel steel

Neutron irradiation is known to cause embrittlement of iron-based materials; in the nuclear industry, this effect can be detrimental for reactor pressure vessel steels. In this paper, we investigate the variations of the magnetic hysteretic behavior due to neutron irradiation, for four materials, i.e. nominally pure Fe, Fe-0.1 wt% Cu and Fe-0.3 wt%Cu model alloys, and a reactor pressure vessel steel, JRQ A533-B. Two parameters related to the magnetization loop shape, i.e. maximum relative differential permeability and peak intensity of local interaction field distribution, are measured as a function of neutron fluence. For all materials both parameters decrease with increasing fluence, due to the irradiation-induced formation of nano-size defects. This decreasing trend in magnetic parameters during embrittlement is noticeable regardless the origin of the embrittlement, which can be only Cu-precipitation (thermal aging of Fe–Cu), only matrix damage (irradiation of pure Fe), or both mechanisms (irradiation of Fe–Cu or steel). The magnetic parameters relatively change up to 40%, which indicates the potential of magnetic characterization to assess irradiation-induced material hardening and embrittlement.     

Effect of annealing temperature on the microstructure and optical–electrical properties of Cu–Al–O thin films

We have successfully prepared Cu–Al–O thin films on silicon (100) and quartz substrates by radio frequency (RF) magnetron sputtering method. The as-deposited Cu–Al–O film is amorphous in nature and post-annealing treatment in argon ambience results in crystallization of the films and the formation of CuAlO₂. The annealing temperature plays an important role in the surface morphology, phase constitution and preferred growth orientation of CuAlO₂ phase, thus affecting the properties of the film. The film annealed at 900 °C is mainly composed of CuAlO₂ phase and shows smooth surface morphology with well-defined grain boundaries, thus exhibiting the optimum optical–electrical properties with electrical resistivity being 79.7 Ω·cm at room temperature and optical transmittance being 80% in visible region. The direct optical band gaps of the films are found in the range of 3.3–3.8 eV depending on the annealing temperature.     

First principles study on the electronic structure and magnetism of Fe1-xCoxSi alloys

Electronic and magnetic properties of Fe1-xCoxSi alloys were investigated by using a full-potential linear augmented-plane-wave method based on density functional theory. Electronic structure calculation demonstrates that half-metallic property appears in the Fe-rich region of 0 〈 x ≤ 0.25, while the alloys turn out to be a magnetic metal for x 〉 0.25. The concentration dependence of the magnetic moment of the alloys can be understood by the fixed Fermi level at minority band in Fe-rich region, as well as at the majority band in Co-rich region. In Fe-rich alloys, the electronic structure and the magnetic properties at Fe site depend mainly on the spin-polarization of nearest neighbouring Co atoms, while in Co-rich alloys, these features at Co site arise mainly from the neighbours of Fe atoms.     

Influence of gamma radiation on morphology structure,electrochemical corrosion behavior and hardness of Ni–Cr based alloys

This study evaluates the effects of gamma radiation on structure, electrochemical corrosion behavior and Vickers hardness of commercial dental Nikkeli–Kromi–Polttosekoitus [Ni_65.2Cr_22.5Mo_9.5X_2.8 (X=Nb, Si, Fe and Mn)] alloy. The corrosion rate of Ni_65.2Cr_22.5Mo_9.5X_2.8 (X=Nb, Si, Fe and Mn) alloy with 0.5 M HCl is increased with increasing the exposure rate of gamma radiation. The corrosion resistance of Ni_65.2Cr_22.5Mo_9.5X_2.8 (X=Nb, Si, Fe and Mn) is varied and reaches a minimum value at 30 KGy. The corrosion potential value also is varied and reaches its highest value at 30 KGy. The Vickers hardness value of Ni_65.2Cr_22.5Mo_9.5X_2.8 (X=Nb, Si, Fe and Mn) alloy is decreased by increasing the gamma radiation dose. Also it is obvious from our results that the effects of gamma radiation at the surface are much higher as compared with deeper parts and the structure of the alloy is changed due to its exposure to gamma radiation.     

Precipitation and fracture behaviour of Fe–Mn–Ni–Al alloys

The effects of Al addition on the precipitation and fracture behaviour of Fe–Mn–Ni alloys were investigated. With the increasing of Al concentration, the matrix and grain boundary precipitates changed from L1₀ θ-MnNi to B2 Ni₂MnAl phase, which is coherent and in cube-to-cube orientation relationship with the α′-matrix. Due to the suppression of the θ-MnNi precipitates at prior austenite grain boundaries (PAGBs), the fracture mode changed from intergranular to transgranular cleavage fracture. Further addition of Al resulted in the discontinuous growth of Ni₂MnAl precipitates in the alloy containing 4.2?wt.% Al and fracture occurred by void growth and coalescence, i.e. by ductile dimple rupture. The transition of the fracture behaviour of the Fe–Mn–Ni–Al alloys is discussed in relation to the conversion of the precipitates and their discontinuous precipitation behaviour at PAGBs.