Growth and characteristics of reactive pulsed laser deposited molybdenum trioxide thin films

Molybdenum trioxide thin films were prepared by reactive pulsed laser deposition on Corning 7059 glass substrates. The influence of oxygen partial pressure and deposition temperature on the structure, surface morphology and optical properties of these films was studied to understand the growth mechanism of MoO₃ thin films. The films formed at 473 K in an oxygen partial pressure of 100 mTorr exhibited predominantly a (0k0) orientation, corresponding to an orthorhombic layered structure of α-MoO₃. The evaluated optical band gap of the films was 3.24 eV. The crystallite size increased with increase of deposition temperature. The films formed at an oxygen partial pressure of pO₂=100 mTorr and at a deposition temperature greater than 700 K exhibited both (0k0) and (0kl) orientations, representing α-β mixed phases of MoO₃. The films formed at an oxygen partial pressure less than 100 mTorr were found to be sub-stoichiometric with α-β mixed phases. The investigation revealed the growth of polycrystalline and single-phase orthorhombic-layered-structure α-MoO₃ thin films with composition nearly approaching the nominal stoichiometry at moderate substrate temperatures in an oxygen partial pressure of 100 mTorr. Received: 9 April 2001 / Accepted: 6 August 2001 / Published online: 17 October 2001     

Electrochromic properties of nanocrystalline WO3 thin films grown on flexible substrates by plasma-assisted evaporation technique

Thin films of Tungsten trioxide (WO₃) were deposited on ITO-coated flexible Kapton substrates by plasma-assisted activated reactive evaporation (ARE) technique. The influence of growth and microstructure on optoelectrochromic properties of WO₃ thin films was studied. The nanocrystalline WO₃ films grown at substrate temperature of 250°C were composed of vertically elongated cone-shaped grains of size 65 nm with relative density of 0.71. These WO₃ films demonstrated higher optical transmittance of 85% in the visible region with estimated optical band gap of 3.39 eV and exhibited better optical modulation of 66% and coloration efficiency of 52.8 cm²/C at the wavelength of 550 nm.     

Chemical,optical, and electrical characterization of Ga2O3 thin films grown by plasma-enhanced atomic layer deposition

Thin Ga₂O₃ films were grown on Si (100) using trimethylgallium (TMG) and oxygen as the precursors through plasma-enhanced atomic layer deposition. The depositions were made over a temperature range of 80–250?°C with a growth per cycle of around 0.07 nm/cycle. Surface self-saturating growth was obtained with TMG pulse time ≥20?ms?at a temperature of 150?°C. The root mean square surface roughness of the obtained Ga₂O₃ films increased from 0.1?nm to 0.3?nm with increasing the growth temperature. Moreover, the x-ray photoelectron spectroscopy analysis indicated that the obtained film was Ga-rich with the chemical oxidation states Ga³⁺ and Ga¹⁺, and no carbon contamination was detected in the films after Ar⁺ sputtering. The electron density of films measured by x-ray reflectivity varied with the growth temperature, increasing from 4.72 to 5.80?g/cm³. The transmittance of Ga₂O₃ film deposited on a quartz substrate was obtained through ultraviolet visible (UV–Vis) spectroscopy. An obvious absorption in the deep UV region was demonstrated with a wide band gap of 4.6–4.8?eV. The spectroscopic ellipsometry analysis indicated that the average refractive index of the Ga₂O₃ film was 1.91?at 632.8?nm and increased with the growth temperature due to the dense structure of the films. Finally, the I-V and C-V characteristics proved that the Ga₂O₃ films prepared in this work had a low leakage current of 7.2?×?10^?11 A/cm² at 1.0?MV/cm and a high permittivity of 11.9, suitable to be gate dielectric.     

SnO2 thin films grown by pulsed Nd:YAG laser deposition

SnO₂ thin films have been deposited on glass substrates by pulsed Nd:YAG laser at different oxygen pressures, and the effects of oxygen pressure on the physical properties of SnO₂ films have been investigated. The films were deposited at substrate temperature of 500°C in oxygen partial pressure between 5.0 and 125 mTorr. The thin films deposited between 5.0 to 50 mTorr showed evidence of diffraction peaks, but increasing the oxygen pressure up to 100 mTorr, three diffraction peaks (110), (101) and (211) were observed containing the SnO₂ tetragonal structure. The electrical resistivity was very sensitive to the oxygen pressure. At 100 mTorr the films showed electrical resistivity of 4×10⁻² Ω cm, free carrier density of 1.03×10¹⁹ cm⁻³, mobility of 10.26 cm² V⁻¹ s⁻¹ with average visible transmittance of ∼87%, and optical band gap of 3.6 eV.     

Structural, electrical, and surface characteristics of La0.5Sr0.5CoO3 thin films prepared by pulsed-laser deposition

A parametric study of the growth of La_0.5Sr_0.5CoO₃ (LSCO) thin films on (100) MgO substrates by pulsed-laser deposition (PLD) is reported. Films are grown under a wide range of substrate temperature (450–800 °C), oxygen pressure (0.1–0.9 mbar), and incident laser fluence (0.8–2.6 J/cm²). The optimum ranges of temperature, oxygen pressure, and laser fluence to produce c-axis oriented films with smooth surface morphology and high metallic conductivity are identified. Films deposited at low temperature (500 °C) and post-annealed in situ at higher temperatures (600–800 °C) are also investigated with respect to their structure, surface morphology, and electrical conductivity. Received: 20 November 1998 / Accepted: 6 July 1999 / Published online: 21 October 1999     

The effect of oxygen pressure on the structure, morphology and photoluminescence intensity of pulsed laser deposited Gd2O2S:Tb3+ thin film phosphor

Luminescent Gd₂O₂S:Tb³⁺ phosphor thin films were grown on Si (100) substrates, using the pulsed laser deposition technique. The films were grown in 100 to 300 mTorr oxygen gas (O₂) atmospheres when the substrate temperature was kept constant at 400 or 600°C. The effect of the O₂ ambient on the structure and morphological properties of the films were analyzed using x-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM), respectively. Spherical nanoparticles deposited on the Si (100) substrates were shown to crystallize in the hexagonal structure of Gd₂O₂S. The photoluminescence (PL) spectra of all the films were characterized by a stable green emission peak with a maximum at 545 nm. Improved PL intensity was observed from the films deposited at higher oxygen pressures and higher substrate temperatures. Particles sizes of the nanoparticles deposited under the different conditions varied between 19 and 36 nm for the different samples. Smaller and more densely packet particles were produces at the higher O₂ pressures and the higher temperature.     

XPS analysis and luminescence properties of thin films deposited by the pulsed laser deposition technique

This paper presents the effect of substrate temperature and oxygen partial pressure on the photoluminescence (PL) intensity of the Gd₂O₂S:Tb^3?+? thin films that were grown by using pulsed laser deposition (PLD). The PL intensity increased with an increase in the oxygen partial pressure and substrate temperature. The thin film deposited at an oxygen pressure of 900 mTorr and substrate temperature of 900°C was found to be the best in terms of the PL intensity of the Gd₂O₂S:Tb^3?+? emission. The main emission peak due to the ⁵D₄–⁷F₅ transition of Tb was measured at a wavelength of 545 nm. The stability of these thin films under prolonged electron bombardment was tested with a combination of techniques such as X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES) and Cathodoluminescence (CL) spectroscopy. It was shown that the main reason for the degradation in luminescence intensity under electron bombardment is the formation of a non-luminescent Gd₂O₃ layer, with small amounts of Gd₂S₃, on the surface.     

Pulsed laser deposition of ZnO as conductive buffer layer of (001)-LiNbO3 thin films

1 (LO) mode peak at 579 cm^-1, indicating oxygen deficiency in the films. Significant dependence of the electrical property for the films on substrate temperature was shown. The I–V relation of the films exhibited non-ohmic behavior. Whereas the films deposited above 500 °C showed a metal-like property, at a lower substrate temperature semiconducting thin films were achieved. The (001)-oriented LiNbO₃/ZnO heterostructure was successfully prepared on quartz fused and (001) sapphire plates. Received: 6 April 1998/Accepted: 26 May 1998     

Electrical and optical properties of indium tin oxide thin films grown by pulsed laser deposition

Indium tin oxide (ITO) thin films (200-400 nm in thickness) have been grown by pulsed laser deposition (PLD) on glass substrates without a post-deposition anneal. The electrical and optical properties of these films have been investigated as a function of substrate temperature and oxygen partial pressure during deposition. Films were deposited at substrate temperatures ranging from room temperature to 300 °C in O₂ partial pressures ranging from 0.1 to 100 mTorr. For 300 nm thick ITO films grown at room temperature in oxygen pressure of 10 mTorr, the electrical conductivity was 2.6᎒^-3 Q^-1cm^-1 and the average optical transmittance was 83% in the visible range (400-700 nm). For 300 nm thick ITO films deposited at 300 °C in 10 mTorr of oxygen, the conductivity was 5.2᎒^-3 Q^-1cm^-1 and the average transmittance in the visible range was 87%. Atomic force microscopy (AFM) measurements showed that the RMS surface roughness for the ITO films grown at room temperature was ~7 Å, which is the lowest reported value for the ITO films grown by any film growth technique at room temperature.     

Role of growth temperature and oxygen partial pressure on the structural and electrical properties of pulsed laser deposited La1−xSrxnO3−δ thin films

The paper presents the fabrication and characterization of La_0.65Sr_0.35MnO_3−δ (LSMO) polycrystalline thin films deposited directly on Si (1 0 0) substrates using pulsed laser deposition technique. Various deposition parameters like substrate temperature and oxygen partial pressure have been varied systematically to obtain stoichiometric, crack-free films with smooth surface morphology having nearly monodisperse grain size distribution. The substrate temperature variation from 600 to 800 °C had profound effects on the microstructure and topography of the deposited film, with optimum result being obtained at 700 °C. The variation of partial pressure of oxygen controls the deposition kinetics as well as the stoichiometry of the film in terms of oxygen vacancy, which influences the magnetic and electrical transport properties of the manganate films. The microstructure and crystallinity of the deposited films have been studied using X-ray diffraction, scanning electron microscopy and atomic force microscopy. A correlation between the oxygen stoichiometry and micro-structural and transport properties of the deposited films has been obtained.     

Microstructural and optical properties of nanocrystalline undoped zirconia thin films prepared by pulsed laser deposition

The zirconium oxide (ZrO₂) thin films are deposited on Si (100) and quartz substrates at various substrate temperatures (room temperature–973 K) at an optimized oxygen partial pressure of 3×10^?2 mbar using pulsed laser deposition technique. The effect of substrate temperature on microstructural, optical and mechanical properties of the films is investigated. The X-ray diffraction studies show that the films deposited at temperatures ≤773 K are monoclinic, while the films deposited at temperatures ≥873 K show both monoclinic and tetragonal phases. Tetragonal phase content increases with the increase of substrate temperatures. The surface morphology and roughness are investigated using atomic force microscope in contact mode. The optical properties of the films show that the refractive indices (at 550 nm) are found to increase from 1.84 to 2.35 as the temperature raises from room temperature (RT) to 973 K. Nanoindentation measurements show that the hardness of the films is 11.8 and 13.7 GPa for the films deposited at 300 and 973 K, respectively.     

Room-temperature epitaxial growth of CeO2(001) films on YSZ buffered Si(001) substrates

2 (001) epitaxial thin films deposited on Si(001) with yttria-stabilized zirconia buffers have been obtained for the first time at room temperature by pulsed-laser deposition. The influence of oxygen pressure on the crystal quality of CeO₂ was studied for the films deposited at 100 °C. The rocking curve full width at half maximum of the CeO₂(002) peak for films deposited at room temperature and 100 °C was between 1° and 2°, for oxygen pressures below 3×10^-2 mbar. The best crystal quality was obtained at around 3×10^-3 mbar. Epitaxial growth at room temperature was confirmed by cross-sectional transmission electron microscopy. Scanning electron microscopy and atomic force microscopy revealed very smooth surfaces for oxygen pressure below 3×10^-2 mbar, with rms roughness values around 0.3 nm over 5 μm×5 μm. Received: 25 September 1997/Accepted: 22 April 1998     

Microstructural, optical and spectroscopic studies of laser ablated nanostructured tantalum oxide thin films

Thin films of tantalum oxide (Ta₂O₅) have been prepared by pulsed laser deposition technique at different substrate temperatures (300-973 K) under vacuum and under oxygen background (pO₂ = 2 × 10⁻³ mbar) conditions. The films are annealed at a temperature of 1173 K. The as-deposited films are amorphous irrespective of the substrate temperature. XRD patterns show that on annealing, the films get crystallized in orthorhombic phase of tantalum pentoxide (β-Ta₂O₅). The annealed films deposited at substrate temperatures 300 K and 673 K have a preferred orientation along (0 0 1) plane, whereas the films deposited at substrate temperatures above 673 K show a preferred orientation along (2 0 0) crystal plane. The deposited films are characterized using techniques such as grazing incidence X-ray diffraction (GIXRD), atomic force microscopy (AFM), micro-Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy and UV-visible spectroscopy. FTIR and micro-Raman measurements confirm the presence of Ta-O, Ta-O-Ta and O-Ta-O bands in the films. Grain size calculations from X-ray diffraction and AFM show a decrease with increase in substrate temperature. The variation of transmittance and band gap with film growth parameters are also discussed.     

The effect of argon gas pressure on structural,morphological and photoluminescence properties of pulsed laser deposited KY<Subscript>3</Subscript>F<Subscript>10</Subscript>:Ho<Superscript>3+</Superscript> thin films

KY₃F₁₀:Ho³⁺ thin films were deposited by a pulsed laser deposition technique with Nd–YAG laser radiation (λ = 266 nm) on (100) silicon substrate. The XRD and FE-SEM results show improved crystalline structure for the film deposited at a pressure of 1 Torr. The AFM results show that the RMS roughness of the films increases with rise in argon gas pressure. The EDS elemental mapping shows Y-excess for all the films deposited under all pressures, and this is attributed to its higher mass and low volatility as compared to K and F. XPS analysis further confirmed Y-excess in the deposited films. Green PL emission at 540 nm was investigated at three main excitation wavelengths, namely 362, 416 and 454 nm. The PL emission peaks increase with rise in background argon gas pressure for all excitation wavelengths. The highest PL intensity occurred at excitation of 454 nm for all the thin films. In addition, faint red (near infrared) emission was observed at 750 nm for all the excitations. The green emission at 540 nm is ascribed to the ⁵F₄–⁵I₈ and ⁵S₂–⁵I₈ transitions, and the faint red emission at 750 nm is due to the ⁵F₄–⁵I₇ and ⁵S₂–⁵I₇ transitions of Ho³⁺.     

Influence of oxygen on structural and optoelectronic properties of CdS thin film deposited by magnetron sputtering technique

In this study, CdS thin films with thicknesses of approximately 100 nm were deposited at a substrate temperature of 100 °C by a sputtering technique under two different ambient conditions—pure Ar ambient and Ar/O₂ (99:1) ambient—at deposition power densities of 1.0 and 2.0 W/cm², respectively The films were polycrystalline with a preferential orientation along the (002) crystal plane; however, the films deposited in the Ar/O₂ ambient exhibited reduced crystallinity. Furthermore, the crystallite sizes, micro-strains, and dislocation densities of the films were significantly affected by oxygen diffusion into the films’ crystal structures. The CdS films deposited in the Ar/O₂ ambient demonstrated higher optical transmittance and higher bandgaps. Morphologies observed from scanning electron microscopy images revealed that the grains of the films were also significantly affected by the oxygen present in the deposition ambient. Additionally, photoluminescence analysis revealed that the sulfur vacancies in the CdS films were partially filled by oxygen atoms, causing significant variations in the electrical properties of the films.     

Large blue shift in the optical band-gap of sol-gel derived Ba0.5Sr0.5TiO3 thin films

In this paper, we report and analyze the large blue shift in the optical band-gap of sol-gel derived Ba_0.5Sr_0.5TiO₃ (BST) thin films. BST films of different thickness (150 nm, 320 nm and 480 nm respectively) were deposited layer by layer onto fused quartz substrates by a spin coating technique. The drying temperature for individual layers (pre-sintering temperature) was varied as 400, 500 and 600 ^°C. A large blue shift in the band-gap was observed (with a value 4.70 eV compared to the bulk value of 3.60 eV) for films pre-sintered at 400 ^°C, which decreased with increase in the pre-sintering temperature. To date such blue shifts have been attributed to grain size reduction, stress and the amorphous nature of the films. Here, the blue shift has been correlated with the presence of charge carriers generated by oxygen vacancies and explained on the basis of the Burstein-Moss effect.     

Physical investigations on pulsed laser deposited nanocrystalline ZnO thin films

The nanocrystalline ZnO thin films were deposited by pulsed laser deposition on quartz and i-Si (100) substrates at different substrate temperatures (473 K–873 K) and at different mixed partial pressures (0.05, 0.01, and 0.5 mbar) of Ar+O₂. The structural studies from XRD spectra reveals that the films deposited at 0.05 mbar and at lower substrate temperatures were c-axis oriented with predominant (002) crystallographic orientation. At 873 K along with (002) orientation, additional crystallographic orientations were also observed in case of films deposited at 0.01 and 0.5 mbar pressures. The composition of Zinc and Oxygen in ZnO films from EDAX reveals that the films deposited at lower partial pressures were have high at.% of O₂ whereas higher partial pressures and substrate temperatures had high at.% Zn. The surface microstructure of the films show that the films deposited at lower partial pressures (0.05 mbar ) and at lower substrate temperatures (473 K) were found to have nanoparticles of size 15 nm where as films deposited at 873 K have nanorods. The length of these nanorods increases with increasing Ar+O₂ partial pressure to 0.5 mbar. The optical energy gap of the film deposited at lower partial pressure and substrate temperature was 3.3 eV and decrease with the increase of substrate temperatures. The films deposited at 0.5 mbar and at 873 K emitted an intense luminescence at a wavelength of 390 nm. The measured thickness of deposited films by spectroscopic ellipsometry is around 456 nm.     

Enhanced fatigue property of PZT thin films using LaNiO3 thin layer as bottom electrode

A highly (100)-oriented metallic LaNiO₃ film was prepared directly on a Si substrate by a simple metalorganic decomposition (MOD) technique using lanthanum nitrate and nickel acetate as the starting sources. Subsequent Pb(Zr,Ti)O₃ (PZT) thin films deposited on the LaNiO₃-coated Si substrate were obtained by a modified sol–gel method. It was found that the PZT thin films began to form a single perovskite phase at a low annealing temperature of 530 °C, and exhibited highly (100) orientation. A ferroelectric capacitor of Pt/Pb(Zr,Ti)O₃/LaNiO₃/Si annealed at 600 °C displayed a good P-E hysteresis characteristic and was fatigue-free even after 10¹¹ switching cycles. Received: 25 May 2000 / Accepted: 9 August 2000 / Published online: 30 November 2000     

Structural and optical characterization of DC magnetron sputtered molybdenum oxide films

Thin films of molybdenum trioxide were deposited on glass substrates employing direct current (DC) magnetron sputtering by sputtering of molybdenum at different oxygen partial pressures in the range 8 × 10⁻⁵–1 × 10⁻³ mbar and at a substrate temperature of 473 K. The glow discharge characteristics of magnetron cathode target of molybdenum were studied. The influence of oxygen partial pressure on the structural and optical properties of molybdenum trioxide films was investigated. The films formed at an optimum oxygen partial pressure of 2 × 10⁻⁴ mbar were polycrystalline in nature with orthorhombic α- phase and an optical band gap of 3.16 eV. The refractive index of the films formed at an oxygen partial pressure of 2 × 10⁻⁴ mbar decreased from 2.08 to 1.89 with increase of wavelength from 450 to 1,000 nm, respectively. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Structural and electrical properties of lithium manganese oxide thin films grown by pulsed laser deposition

LiMn₂O₄ thin films were deposited by reactive pulsed laser deposition technique and studied the microstructural and electrical properties of the films. The LiMn₂O₄ thin films deposited in an oxygen partial pressure of 100 mTorr and at a substrate temperature of 573 K from a lithium rich target were found to be nearly stoichiometric. The films exhibited predominantly (111) orientation representing the cubic spinel structure with Fd3m symmetry. The intensity of (111) peak increased and a slight shift in the peak position was observed with the increase of substrate temperature. The lattice parameter increased from 8.117 to 8.2417 Å with the increase of substrate temperature from 573 to 873 K. The electrical conductivity of the films is observed to be a strong function of temperature. The evaluated activation energy for the films deposited at 873 K is 0.64 eV.