Organic/inorganic interfaced field-effect transistor properties with a novel organic semiconducting material

A novel 1,3,4-oxadiazole-substituted benzo[b]triphenylene was synthesized by three-step synthetic procedure and OFET device design was successfully designed after theoretical calculations made using Gaussian software. For investigating the field-effect properties of designed organic electronic device, a SiO₂ (300 nm) was thermally grown on p-Si wafer at 1000 °C as a dielectric layer and gate, source and drain contacts have been deposited using Au metal with physical vapour deposition. 1,3,4-Oxadiazole-substituted benzo[b]triphenylene was spin coated on the source and drain electrodes of our device, forming organic/inorganic interfaced field-effect transistors. Surface morphology and thin film properties were investigated using AFM. All electrical measurements were done in air ambient. The device showed a typical p-type channel behaviour with increasing negative gate bias voltage values. Our results have surprisingly shown that the saturation regime of this device has high mobility (μ_FET), excellent on/off ratio (I_on/I_off), high transconductance (g_m) and a small threshold voltage (V_Th). The values of μ_FET, I_on/I_off, g_m and V_Th were found as 5.02 cm²/Vs, 0.7 × 10³, 5.64 μS/mm and 1.37 V, respectively. These values show that our novel organic material could be a potential candidate for organic electronic device applications in the future.     

Theoretical studies on structure and performance of [1,2,5]‐oxadiazolo‐[3,4‐d]‐pyridazine‐based derivatives

Based on energetic compound [1,2,5]‐oxadiazolo‐[3,4‐d]‐pyridazine, a series of functionalized derivatives were designed and first reported. Afterwards, the relationship between their structure and performance was systematically explored by density functional theory at B3LYP/6‐311 g (d, p) level. Results show that the bond dissociation energies of the weakest bond (N–O bond) vary from 157.530 to 189.411 kJ · mol^?1. The bond dissociation energies of these compounds are superior to that of HMX (N–NO_2, 154.905 kJ · mol^?1). In addition, H1, H2, H4, I2, I3, C1, C2, and D1 possess high density (1.818–1.997 g · cm^?3) and good detonation performance (detonation velocities, 8.29–9.46 km · s^?1; detonation pressures, 30.87–42.12 GPa), which may be potential explosives compared with RDX (8.81 km · s^?1, 34.47 GPa ) and HMX (9.19 km · s^?1, 38.45 GPa). Finally, allowing for the explosive performance and molecular stability, three compounds may be suggested as good potential candidates for high‐energy density materials. Copyright © 2016 John Wiley & Sons, Ltd.     

对以并五苯和酞菁铜为不同有源层的有机薄膜晶体管特性研究

通过扫描电镜和X射线衍射对SiO₂衬底上生长并五苯和酞菁铜薄膜的表面形貌进行表征,并得到在SiO₂衬底上生长的并五苯薄膜是以岛状结构生长,其大小约为100nm,且薄膜有较好的结晶取向,呈多晶态存在. 酞菁铜薄膜则没有表现出明显的生长机理,其呈非晶态存在. 还对通过掩膜的方法制作得以酞菁铜和并五苯为有源层的顶栅极有机薄膜晶体管的特性进行了研究. 有源层的厚度为40nm,绝缘层SiO₂的厚度为250nm,器件的沟道宽长比(W/关键词： 有机薄膜晶体管 并五苯薄膜 酞菁铜薄膜 μ_EF)')" href="#">场效应迁移率(μ_EF)     

低栅极电压控制下带有phenyltrimethoxysilane单分子自组装层的有机薄膜晶体管场效应特性研究

制作了底栅极顶接触有机薄膜晶体管器件,60 nm的pentacene被用作有源层,120 nm热生长的SiO₂作为栅极绝缘层.通过采用不同自组装修饰材料对器件的有源层与栅极绝缘层之间的界面进行修饰,如octadecyltrichlorosilane （OTS）,phenyltrimethoxysilane （PhTMS）,来比较界面修饰层对器件性能的影响.同时对带有PhTMS修饰层的OTFTs器件低栅极电压调制下的场效应行为及其载流子的传输机理进行研究.结果得到,当|V 关键词： 有机薄膜晶体管 自组装单分子层 场效应迁移率 低栅极调制电压     

New small organic molecules based on thieno[2,3-b]indole for efficient bulk heterojunction organic solar cells: a computational study

ABSTRACT

This study aims to evaluate the characteristics of novel organic D-π-A-π-D class small-molecules by using carefully the density functional theory, and time-dependent density functional theory calculations. Thedesigned sequence of (D-A) BHJ-1a to BHJ-4a in organic Bulk Heterojunction (BHJ) solar cells has been comprehensively analysed. Thiéno[2,3-b]indole (TI) has been used as donor, and Diketopyrrolopyrrole (DPP) as acceptor for all compounds. In order to improve the electronic, photovoltaic, and opticalproperties, we have substituted thiophene unit with furan, thieno[2,3-b]thiophene, thiazole and thiazolothiazole as π-bridge moieties. Thus, the result shows that the wise choice of the π-bridge units plays a significant role in improving E_gap, producing a high bathochromic shift, and increasing V_OC as well as a theoretical power conversion efficiency (PCE) over 7%. Interestingly, BHJ-4a with suitable π-bridge presents the optimal electronic properties with low band gap (1.870?eV) and high V_OC (1.534?eV). Furthermore, we have modelled a Bulk heterojunction organic photovoltaic cells based on donor-PCBM complex in order to achieve the optimum E_gap and V_OC. Consequently, the obtained results provide a new way to design BHJ small molecule donors with higher power conversion efficiency.     

LiAr, LiKr and LiXe excimers: Photochemical formation of the - bands

We investigated the photochemical formation of lithium-rare-gas excimers in the 3 state through the reaction of Li₂(2(C)) and the ground-state rare-gas atom. Lithium-rare-gas vapor mixture was prepared in the heat-pipe oven. We populated the 2(C)state of the Li₂ molecule using the XeCl excimer laser wavelength at 308 nm or the PTP dye laser wavelength at about 335 nm. The 3-1 transitions were observed with peaks at 414, 420 and 435 nm for LiAr, LiKr and LiXe, respectively. We estimated thermally averaged rate constants for these photochemical reactions, which are cm³s^-1 for LiAr, cm ³ s^-1 for LiKr and cm³s^-1 for LiXe. Ab initio potential-energy curves and transition dipole moments for LiKr were calculated applying the SCF MRDCI method. Available data for the LiAr and LiKr excimers are presented, including potential-energy curves, electronic transition dipole moments, and spectroscopic constants. Possible photochemical formation of these molecules in the excited states is discussed. We performed the quantum-mechanical spectral simulations of the LiAr and LiKr 3-1 transitions, using ab initio potential-energy curves. Received: 2 October 1998 / Received in final form: 25 January 1999     

Study on solid structure of pentacene thin films using Raman imaging

We present a 532‐nm excited Raman imaging study of pentacene thin films (thickness, 2, 5, 10, 20, 50, 100, and 150 nm) prepared on an SiO₂ surface. The structure of the pentacene films has been investigated by images and histograms of the ratio (R) of intensity of the 1596‐cm⁻¹ band (b_3g) to that of the 1533‐cm⁻¹ band (a_g), which can be used as a marker of solid‐state phases: 1.54‐nm and 1.44‐nm phases. The Raman images showed that island‐like 1.44‐nm phase domains are grown on the 1.54‐nm phase layer from 50 nm, and all the surface of the 1.54‐nm phase layer is covered with the 1.44‐nm phase layer from 100 nm. The structural disorders have been discussed on the basis of the full width at half maximum of a band in the histogram of the R values for each film. Copyright © 2012 John Wiley & Sons, Ltd.     

Amphiphilic p‐tert‐butylthiacalix[4]arenes containing quaternary ammonium groups: from small molecules toward water‐soluble nanoscale associates

The formation of supramolecular associates based on water‐soluble p‐tert‐butylthiacalix[4]arenes with amino acids has been studied. It was shown that amphiphilic p‐tert‐butylthiacalix[4]arenes preferably formed supramolecular associates with aromatic α‐amino acids (tyrosine and tryptophan). Increasing size of the substituents of p‐tert‐butylthiacalix[4]arenes led to increase molecular weight of supramolecular associates based on the macrocycles and “guest” molecules. The spatial structures of p‐tert‐butylthiacalix[4]arenes and their associates with phenylalanine were studied by two‐dimensional ¹H‐¹H nuclear Overhauser effect NMR spectroscopy. The ability of aggregates based on p‐tert‐butylthiacalix[4]arenes and amino acids to effectively interact with bovine serum albumin with the formation of 7‐ to 8‐nm nanoparticles was shown. Copyright © 2015 John Wiley & Sons, Ltd.     

Frequency- and wavelength-modulation spectroscopies: Comparison of experimental methods using an AlGaAs diode laser

Low-wavelength modulation (1 kHz), high-wavelength modulation (100 MHz) and two-tone frequency modulation (390±5 MHz) spectroscopies are systematically compared by measuring the minimum detectable absorption achieved using an AlGaAs diode laser tuned on a third-overtone methane transition at 886 nm. From the S/N behavior has been extrapolated a minimum relative absorption (1 Hz of bandwidth) of 4.5(1)×10^–7 for the LMW, 9.7(3)×10^–8 for the HWM and 6.4(2)×10^–8 for the TTFM. In the LWM case the detection-limit value is represented by the laser amplitude 1/f excess noise, while for the high-frequency detection techniques this contribution is negligible with respect to other noise sources. These detection limits well agree with the calculated quantum limited values based on measured laser power, modulation index, noise figure of the electronic components, and other parameters of the apparatus.     

Mass Spectral Fragmentation Patterns of Some Substituted 10,Ll-Dihydro-5H-Dibenzo[A,D] Cycloheptene-5-One and 9,10-Dihydro-4H-Benzo [4,5]Cyclohepta[1,2-B]Thiophene-4-One

Electron impact mass spectra of some substituted 10,11-dihydro-5H-dibenzo[a,d]cyclohepten-5-one and 9,10-dihydro-4H-benzo[4,5] cyclohepta[1,2-b] thiophene-4-one have been recorded and the identity of various ions in the mass spectra established. Substituted dibenzosuberones (2-6) exhibit one main fragmentation route, which include the elimination of the tropolone molecule from the dibenzosuberone fragment cation. Their monothiophene analogues(7-11) exhibit characteristic CO elimination from the molecular ion and formation of corresponding naphtho[1,2-b]thiophene radical cation which after elimination of CS or HCS from the thiophene nuclei give rise to the benzotrophyne radical cation.     

Laser-induced voltage effects in Ca3Co4O9 thin films on tilted LaAlO3（001） substrates grown by chemical solution deposition

Laser-induced voltage effects in c-axis oriented Ca3Co4O9 thin films have been studied with samples fabricated on 10 tilted LaAlO3(001) substrates by a simple chemical solution deposition method. An open-circuit voltage with a rise time of about 10 ns and full width at half maximum of about 28 ns is detected when the film surface is irradiated by a 308-nm laser pulse with a duration of 25 ns. Besides, open-circuit voltage signals are also observed when the film surface is irradiated separately by the laser pulses of 532 nm and 1064 nm. The results indicate that Ca3Co4O9 thin films have a great potential application in the wide range photodetctor from the ultraviolet to near infrared regions.     

Time-resolved spectroscopy and energy transfer in Pr3+-doped Gd2(SO4)3·8H2O

The luminescence of Pr³⁺ in gadolinium sulfate hydrate is reported for 195 nm laser excitation. the Pr³⁺ ion acts as a sensitizer of the host lattice emission. The Pr³⁺Gd³⁺ energy transfer occurs in two different ways. In the octahydrate the transfer occurs from the lowest component of the 4f5d configuration of Pr³⁺, but in the samples with less water there is energy transfer from the¹ S _o level of Pr³⁺ to several Gd³⁺ levels. The Pr³⁺ emission in the two modifications is, of course, also strikingly different.Deceased 24 December 1994     

Low voltage electrodeposition of diamond like carbon (DLC)

Attempt has been made to deposit diamond like carbon (DLC) films from ethanol through electrodeposition at low voltages (80-300 V) at 1 mm interelectrode separation. The films were characterized by atomic force microscopy (AFM), Scanning electron microscopy (SEM), Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy and Auger electron Spectroscopy (AES). AFM investigations revealed the grain sizes are of tens of nanometers. The films were found to be continuous, smooth and close packed. Presence of peaks at 2958, 2929 and 2869 cm⁻¹ in FTIR spectrum indicates the bonding states to be of predominantly sp³ type (C-H). Raman spectroscopy analysis revealed two broad bands at ∼1350 and ∼1570 cm⁻¹. The downshift of the G-band of graphite is indicative of presence of DLC. Analysis of the Raman spectra for the samples revealed an improvement in the film quality with increase in the voltage. Micro Raman investigations indicate the formation of diamond phase at the deposition potential of 80 V. The sp² contents the films calculated from Auger electron spectra were calculated and were found to be 31, 19 and 7.8% for the samples prepared at 80, 150 and 300 V, respectively. A tentative mechanism for the formation of DLC has been proposed. These results indicate the possibility of deposition of DLC at low voltage.     

Non-steady-state photo-EMF in nanostructured GaN and polypyrrole within porous matrices

We report an experimental investigation of the non-steady-state photoelectromotive force in nanostructured GaN within porous glass and polypyrrole within chrysotile asbestos. The samples are illuminated by an oscillating interference pattern created by two coherent light beams and the alternating current is detected as a response of the material. Dependences of the signal amplitude versus temporal and spatial frequencies, light intensity, and temperature are studied for two wavelengths λ=442 and 532 nm. The conductivity of the GaN composite is measured: σ=(1.1–1.6)×10⁻¹⁰ Ω⁻¹ cm⁻¹ (λ=442 nm, I ₀=0.045–0.19 W/cm², T=293 K) and σ=(3.5–4.6)×10⁻¹⁰ Ω⁻¹ cm⁻¹ (λ=532 nm, I ₀=2.3 W/cm², T=249–388 K). The diffusion length of photocarriers in polypyrrole nanowires is also estimated: L _D=0.18 μm.     

New pyrazolino and pyrrolidino[60]fullerenes: the introduction of the hydrazone moiety for the formation of metal complexes

The [3 + 2] cycloaddition reaction of C₆₀ with pyridine‐derived hydrazones (acting as dipolar reagents) was successfully conducted resulting in fullerene derivatives 5a , 5b . The compounds were characterized by means of NMR, UV–Vis spectroscopy, and X‐ray crystallography. The electrochemical behavior was also investigated. The fulleropyrazoline 5a exhibits anodically shifted reduction potentials of about 100 mV when compared with those for C₆₀, whereas 5b exhibits cathodic shifts relative to pristine C₆₀. The complexation reaction of 5b with metallic ions (Zn²⁺, Cd²⁺, and Fe²⁺) was achieved. Job and Benesi–Hildebrand analysis confirmed the formation of complexes with a molar ratio of 1:1 and binding constants between 2.26 × 10⁵ and 1.59 × 10⁵ M^?1. Electrochemistry of these complexes showed a marked influence of the metal ion on the reduction potentials. Copyright © 2016 John Wiley & Sons, Ltd.     

Random lasing in an organic light‐emitting crystal and its interplay with vertical cavity feedback

The simultaneous vertical‐cavity and random lasing emission properties of a blue‐emitting molecular crystal are investigated. The 1,1,4,4‐tetraphenyl‐1,3‐butadiene samples, grown by physical vapour transport, feature room‐temperature stimulated emission peaked at about 430 nm. Fabry‐Pérot and random resonances are primed by the interfaces of the crystal with external media and by defect scatterers, respectively. The analysis of the resulting lasing spectra evidences the existence of narrow peaks due to both the built‐in vertical Fabry‐Pérot cavity and random lasing in a novel, surface‐emitting configuration and threshold around 500 μJ cm⁻². The anti‐correlation between different modes is also highlighted, due to competition for gain. Molecular crystals with optical gain candidate as promising photonic media inherently supporting multiple lasing mechanisms.     

Low driving voltage in organic light-emitting diode using MoO3/NPB multiple quantum well structure in hole transport layer

Driving voltage of organic light-emitting diode (OLED) is lowered by employing molybdenum trioxide (MoO₃)/N, N'-bis(naphthalene-1-yl)-N,N'-bis(phe-nyl)-benzidine (NPB) multiple quantum well (MQW) structure in hole transport layer. For the device with double quantum well (DQW) structure of ITO/ [MoO₃ (2.5 nm)/NPB (20 nm)]₂/Alq₃(50 nm)/LiF (0.8 nm)/Al (120 nm)], the turn-on voltage is reduced to 2.8 V, which is lowered by 0.4 V compared with that of the control device (without MQW structures), the driving voltage is 5.6 V, which is reduced by 1 V compared with that of the control device at the 1000 cd/m². In this work, the enhancement of the injection and transport ability for holes could reduce the driving voltage for the device with MQW structure, which is attributed not only to the reducing energy barrier between ITO and NPB, but also to the forming charge transfer complex between MoO₃ and NPB induced by the interfacial doping effect of MoO₃.     

Synthesis and optical properties of novel pyrido[1,2-a]benzimidazole-containing 1,3,4-oxadiazole derivatives

A series of novel substituted 1,3,4-oxadiazole derivatives containing pyrido[1,2-a]benzimidazole moiety were synthesized and characterized using FTIR, ¹H NMR, ¹³C NMR, and HRMS. An efficient tandem reaction was employed as a key step in constructing the pyrido[1,2-a]benzimidazole moiety under very mild condition. The structure of compound 4a was established by X-ray crystallography. The UV-vis absorption and fluorescence spectral characteristics of these compounds were investigated in several solvents. Compounds 4a-i display similar absorptions, with absorption peaks ranging from 330 to 339 nm in acetonitrile, while the absorption maxima of compound 4j bearing a diphenylamino group on the benzene ring is red-shifted distinctly to 377 nm due to the strong electron-donating property of its substituent and extended π-conjugated system. All these target heterocyclic compounds present blue-green emissions (461-487 nm) in dilute solutions and show high quantum yields of fluorescence (Ф_PL=0.65−0.99) in dichloromethane.     

Spatial filtering using poled polymer etalon light modulators

Spatial filtering using poled polymer light modulators is studied. The use of a resonator structure is proposed to minimize the driving voltage. Side-chain polymer poly-orange tom-1 isophoronedisocyanate is used as a material. The measured electro-optic coefficient r ₃₃ is 23 pm/V at the wavelength of 633 nm. Spatial filtering of the input images are realized with 30 V applied voltage.     

铱金属配合物磷光材料掺杂聚合物体系的电致发光特性

通过对一种新型贵金属铱的配合物磷光材料(pbi)₂Ir(acac)与咔唑共聚物进行物理掺杂, 制备了结构为indium-tin oxide(ITO)/poly(N-vinylcarbazole)(PVK): (pbi)₂Ir(acac)(x)/2,9-dimethyl-4,7-diphenyl-1,10-phenan throline(BCP)(20nm)/8-Hydroxyquinoline aluminum(Alq₃)(10nm)/Mg:Ag的聚合物电致磷光器件,研究了磷光聚合物掺杂体系在低掺杂浓度时(0.1%和0.5%(质量百分数,全文同))的光致发光(PL)和电致发光(EL)特性. 结果表明, 该掺杂体系的PL光谱和EL光谱中均同时存在主体材料PVK与磷光客体(pbi)₂Ir(acac)的发光光谱, 但主客体的发射强度不同,推测该掺杂体系在电致发光条件下, 同时存在主体材料到客体的不完全的能量传递和载流子直接俘获过程. 磷光掺杂浓度为0.1%的器件在19V电压下实现了白光发射, 色坐标为(0.32, 0.38), 掺杂浓度为0.5%的器件在20.6V电压下的最大发光亮度为11827 cd·m^-2, 而在13.4V电压下的最大流明效率为4.13 cd·A^-1. 关键词： 有机电致发光器件 铱配合物磷光 聚合物掺杂