Study on the dynamic characteristics of flow over building cluster at high Reynolds number by large eddy simulation

In this paper,the dynamic characteristics of building clusters are simulated by large eddy simulation at high Reynolds number for both homogeneous and heterogeneous building clusters.To save the computational cost a channel-like flow model is applied to the urban canopy with free slip condition at the upper boundary.The results show that the domain height is an important parameter for correct evaluation of the dynamic characteristics.The domain height must be greater than 8h(h is the average building height)in order to obtain correct roughness height while displacement height and roughness sublayer are less sensitive to the domain height.The Reynolds number effects on the dynamic characteristics and flow patterns are investigated.The turbulence intensity is stronger inside building cluster at high Reynolds number while turbulence intensity is almost unchanged with Reynolds number above the building cluster.Roughness height increases monotonously with Reynolds number by 20%from Re*=103 to Re*=105 but displacement height is almost unchanged.Within the canopy layer of heterogeneous building clusters,flow structures vary between buildings and turbulence is more active at high Reynolds number.     

低阶格式在大涡模拟计算中的适用性

采用三维Taylor-Green涡作为研究对象,利用工程中常用的低阶数值格式,研究格式本身的数值误差对大涡模拟计算的影响.结果表明:三种数值格式的数值耗散行为都与亚格子模型行为类似,即在小雷诺数下,流场比较光滑时,耗散很小,当雷诺数增加,流动转捩为湍流,流场梯度增大,耗散显著增大.对于MUSCL格式和二阶有界中心格式,在高雷诺数下,亚格子尺度模型没有明显改善计算结果,但也没有使计算结果恶化.中心格式相比其它两种格式,数值耗散最小,但是在高雷诺数湍流情况下,中心格式的数值耗散仍然主导了能量的耗散,再添加亚格子模型,计算结果反而变得稍差.对于工程中的低阶格式而言,采用中心格式计算大涡模拟是比较好的选择,而且在计算不存在稳定性问题时,采用不添加亚格子模型的隐式大涡模拟效果更好.     

煤油超燃冲压发动机三维大规模并行数值模拟

在我国巨型计算机上,采用1024个CPU对煤油燃料超燃冲压发动机燃烧流场进行三维大规模并行数值模拟.计算软件采用自主研发的并行软件AHL3D,控制方程采用雷诺平均的N-S方程,无粘项计算采用Steger-Warning矢通量分裂格式,湍流模型采用k-ω双方程模型,煤油分子式采用正癸烷代替.计算给出的发动机壁面压强分布与试验测量结果有较好的一致性.结果表明,凹槽是发动机主要的着火区和火焰稳定区,同时,由于燃料的喷注形成的回流区也起到一定的稳焰作用.计算结果验证了AHL3D程序和采用的理论模型可以用于模拟煤油燃料超燃冲压发动机内部的复杂流动.     

Statistical-mechanical predictions and Navier-Stokes dynamics of two-dimensional flows on a bounded domain

In this paper the applicability of a statistical-mechanical theory to freely decaying two-dimensional (2D) turbulence on a bounded domain is investigated. We consider an ensemble of direct numerical simulations in a square box with stress-free boundaries, with a Reynolds number that is of the same order as in experiments on 2D decaying Navier-Stokes turbulence. The results of these simulations are compared with the corresponding statistical equilibria, calculated from different stages of the evolution. It is shown that the statistical equilibria calculated from early times of the Navier-Stokes evolution do not correspond to the dynamical quasistationary states. At best, the global topological structure is correctly predicted from a relatively late time in the Navier-Stokes evolution, when the quasistationary state has almost been reached. This failure of the (basically inviscid) statistical-mechanical theory is related to viscous dissipation and net leakage of vorticity in the Navier-Stokes dynamics at moderate values of the Reynolds number.     

Large eddy simulation of a light gas stratification break-up by an entraining turbulent fountain

The erosion process of a stably stratified light gas layer by a vertical turbulent fountain of denser fluid inside a generic containment – for which experimental reference data are available – is studied computationally using large eddy simulation (LES). In addition, various Reynolds averaged Navier–Stokes (RANS) models are applied aiming at a comparative assessment of different computational approaches for the considered case. With the LES methodology included into the present modelling study, a novelty to date is established for fountain-stratification interaction inside generic containments. The high Reynolds number RANS models applied in the framework of this study include both the realisable k–? eddy viscosity model (EVM) as well as the basic Reynolds stress model (RSM). Furthermore, we show that certain regimes of the present configuration can be predicted using an analytically derived scaling approach. Various data beyond the experimentally obtained ones are computationally provided in order to facilitate the calibration of less costly statistical turbulence models and lumped parameter codes, since the presently considered configuration is regarded to be a valuable small-scale equivalent for containment flow applications.     

Scale separation for implicit large eddy simulation

With implicit large eddy simulation (ILES) the truncation error of the discretization scheme acts as subgrid-scale (SGS) model for the computation of turbulent flows. Although ILES is comparably simple, numerically robust and easy to implement, a considerable challenge is the design of numerical discretization schemes resulting in a physically consistent SGS model. In this work, we consider the implicit SGS modeling capacity of the adaptive central-upwind weighted-essentially-non-oscillatory scheme (WENO-CU6) [X.Y. Hu, Q. Wang, N.A. Adams, An adaptive central-upwind weighted essentially non-oscillatory scheme, J. Comput. Phys. 229 (2010) 8952–8965] by incorporating a physically-motivated scale-separation formulation. Scale separation is accomplished by a simple modification of the WENO weights. The resulting modified scheme maintains the shock-capturing capabilities of the original WENO-CU6 scheme while it is also able to reproduce the Kolmogorov range of the kinetic-energy spectrum for turbulence at the limit of infinite Reynolds number independently of grid resolution. For isentropic compressible turbulence the pseudo-sound regime of the dilatational kinetic-energy spectrum and the non-Gaussian probability-density function of the longitudinal velocity derivative are reproduced.     

用多块多网格方法数值模拟三维粘性流动

本文给出了一个模拟三维粘性流动的数值方法．该方法来用高分辨率 ＴＶＤ Ｌａｘ－Ｗｅｎｄｒｏｆｆ格式求解三维雷诺平均Ｎａｖｉｅｒ－Ｓｔｏｋｅｓ方程，使用Ｂａｌｄｗｉｎ－Ｌｏｍａｘ模型估计湍流粘性系数，用多重网格技术加速收敛，采用多块结构化网格处理复杂的物理域．文中给出了叶轮机械多个叶片排和透平排汽缸内的全三维粘性流动的数值结果．     

Formation of zones of an inverse energy cascade in an axisymmetric jet

The results of investigation into the mechanism of formation of an inverse turbulence energy cascade in an axially symmetric submerged jet based on numerical modeling by the large eddy simulation. The flow structure is calculated using two models of subgrid turbulence in a broad range of Reynolds numbers with the imposed external harmonic low-amplitude perturbation and swirling. Calculations showed that upon imposing swirling, the effect of formation of the inverse cascade is suppressed, while upon imposing the external low-amplitude harmonic perturbations corresponding to the frequency of highest perceptivity, it is enhanced. We can assume that the regions with the inverse turbulence energy flow are formed there where the dynamics of large quasi-2D structures is determined by the mechanisms of combining eddies and involvement processes, while the tension mechanism of vortex tubes is suppressed. It is shown that the balance of these mechanisms can be controlled by means of imposition of low-amplitude harmonic perturbations.     

A restricted nonlinear large eddy simulation model for high Reynolds number flows

Recent numerical studies of the restricted nonlinear (RNL) model have demonstrated its ability to reproduce important features of wall turbulence despite a severe reduction in the number of degrees of freedom. In these prior studies, the RNL model included full resolution of the viscous term. In this work, we extend the RNL model to arbitrarily high Reynolds numbers by developing a RNL large eddy simulation (LES) framework along with a method to systematically identify an appropriate streamwise wavenumber support based on spectral properties of wall turbulence. This method leads to a band-limited RNL–LES system which is successful in reproducing some of the most important statistical features captured in previous low to moderate Reynolds number simulations, e.g. the mean velocity and second-order moment profiles. The RNL–LES framework offers a new approach to understanding the connection between coherent structures and the momentum transfer mechanisms of wall turbulence at arbitrarily high Reynolds numbers, where resolution of the viscous terms can become computationally expensive even with the relatively low computational complexity afforded through the dynamical restriction of the RNL model.     

Pressure spectrum in homogeneous turbulence

The pressure spectrum in homogeneous steady turbulence is studied using direct numerical simulation with resolution up to 1024(3) and the Reynolds number R(lambda) between 38 and 478. The energy spectrum is found to have a finite inertial range with the Kolmogorov constant K = 1.65+/-0.05 followed by a bump at large wave numbers. The pressure spectrum in the inertial range is found to be approximately P(k) = B(p)epsilon;(4/3)k(-7/3) with B(p) = 8.0+/-0.5, and followed by a bump of nearly k(-5/3) at higher wave numbers. Universality and a new scaling of the pressure spectrum are discussed.     

Variational multiscale turbulence modelling in a high order spectral element method

In the variational multiscale (VMS) approach to large eddy simulation (LES), the governing equations are projected onto an a priori scale partitioning of the solution space. This gives an alternative framework for designing and analyzing turbulence models. We describe the implementation of the VMS LES methodology in a high order spectral element method with a nodal basis, and discuss the properties of the proposed scale partitioning. The spectral element code is first validated by doing a direct numerical simulation of fully developed plane channel flow. The performance of the turbulence model is then assessed by several coarse grid simulations of channel flow at different Reynolds numbers.     

Rotation effect on near-wall turbulence statistics and flow structures

Turbulent flow in an axially rotating pipe, involving complicated physical mecha- nism of turbulence, is a typical problem for the study of rotating turbulent flow. The pipe rotation induces two effects on the flow. One is the stabilizing effect due to the centrifu- gal and Coriolis forces, which accounts for the relaminarization of the turbulence[1—3] and the reduction of the friction coefficient at the pipe wall. The behavior is also related to the wall streaks inclining to the azimuthal di…     

Spectral slope and Kolmogorov constant of MHD turbulence

The spectral slope of strong MHD turbulence has recently been a matter of controversy. While the Goldreich-Sridhar model predicts a -5/3 slope, shallower slopes have been observed in numerics. We argue that earlier numerics were affected by driving due to a diffuse locality of energy transfer. Our highest-resolution simulation (3072(2)×1024) exhibited the asymptotic -5/3 scaling. We also discover that the dynamic alignment, proposed in models with -3/2 slope, saturates and cannot modify the asymptotic, high Reynolds number slope. From the observed -5/3 scaling we measure the Kolmogorov constant C(KA)=3.27±0.07 for Alfvénic turbulence and C(K)=4.2±0.2 for full MHD turbulence, which is higher than the hydrodynamic value of 1.64. This larger C(K) indicates inefficient energy transfer in MHD turbulence, which is in agreement with diffuse locality.     

Effects of upstream roughness and Reynolds number on separated and reattached turbulent flow

This paper presents experimental investigation of upstream roughness and Reynolds number effects on the recirculation region over a smooth forward facing step. The upstream rough wall was produced from 1.5 mm sand grains and the Reynolds number based on step height, Re_h, was varied from 2040 to 9130 for both the upstream smooth and rough walls. For the smooth wall, the reattachment length increased monotonically with Re_h to an asymptotic value of 2.2 step heights for Re_h ≥ 6380. Upstream roughness reduced the reattachment length by 44% because of larger momentum deficit and higher turbulence level in the rough wall boundary layer. The mean velocities and Reynolds stresses were also reduced by roughness. The Reynolds shear stress and production of turbulent kinetic energy showed high negative values at the leading edge of the step indicating counter-gradient diffusion. The implications of these results for standard eddy viscosity models are discussed.     

Effect of gravity on the development of homogeneous shear turbulence laden with finite-size particles

Fully resolved simulations of homogeneous shear turbulence (HST) laden with sedimenting spherical particles of finite size have been performed to clarify the effects of gravity on the development of particle-laden turbulent shear flows. We consider turbulence in a horizontal flow subjected to vertical or horizontal shear. Numerical results show that the development of HST laden with finite-size particles are significantly altered by gravity. The effects of gravity lead to a slower increase in the Taylor-microscale Reynolds number, whose value is found to be well correlated with the average particle Reynolds number. The gravity also causes a slower increase in the turbulence kinetic energy (TKE) through the enhancement of energy dissipation. The change in the Reynolds shear stress (RSS) due to particles also significantly contributes to the relative change in TKE. In vertically sheared cases, RSS has high values between counter-rotating trailing vortices behind the particles, which causes a transient relative increase in TKE. In horizontally sheared cases, on the other hand, RSS is reduced in the wakes of particles, which contributes to a significant relative reduction in TKE.     

横向粗糙元壁面槽道湍流的大涡模拟研究

采用大涡模拟和浸没边界法相结合对不同高度和不同间距横向粗糙元壁面槽道湍流进行了模拟,得到了光滑壁面和粗糙壁面湍流的流向平均速度分布,雷诺剪切应力,脉动速度均方根和近壁区拟序结构。结果发现横向粗糙元降低了流向平均速度,增大了流动阻力,粗糙壁面湍流的雷诺剪切应力大于光滑壁面。粗糙元降低了流向脉动速度,增强了展向和法向脉动速度。粗糙元高度越高,对湍流流动影响越大,而粗糙元间距对湍流统计特性的影响不大。粗糙壁面仍然存在着和光滑壁面类似的条带结构。     

A mixed-time-scale low-Reynolds-number one-equation turbulence model

In this paper, a new low-Reynolds-number (LRN) one-equation turbulence model for eddy viscosity is proposed. A mixed time scale, representing a combination of three time scales: two time scales made of strain-rate parameter S and vorticity parameter Ω and the turbulent time scale k/?, is introduced into this model. The proposed model is derived from an LRN k?? two-equation model where the mixed time scale has been proved to be very effective for predicting local flows over complex terrains. In the transport equation of the model, the mixed time scale is included in the production and the dissipation terms. The new model is evaluated in channel flows at various Reynolds numbers, boundary layer flows with or without pressure gradient and backward-facing step flows with different expansion ratios and Reynolds numbers. Then the grid convergence of the model is investigated. Finally, the model performance for different values of the weighting constant C_s in the mixed time scale is assessed. The results show that the proposed model reproduces the correct wall-limiting behaviour of turbulent quantities and performs well in the near-wall region of turbulent flows. The model could be expected to be adopted in hybrid Reynolds averaged Navier–Stokes/large eddy simulation methodology for complex wall-bounded flows at high Reynolds numbers.     

圆柱绕流问题的初期流动数值模拟

本文继Zheng-huan Teng[1]中介绍的解Navier-stokes方程的椭圆涡团法,研究了一种新的变形涡团法,用以模拟不可压粘性流体绕圆柱的不定常流动。圆柱在静止流体中突然起动并做匀速直线运动。对整个流动区域构造完全Navier-Stokes方程的解并不容易,近十年出现很多数值研究,本文对算法有所推进。把本文的方法称作变形涡团法是因为圆柱边界附近的流体中用椭圆涡团,远离边界时用圆形涡团。计算圆柱绕流比平板绕流在满足附着条件上更为困难,本文分析了怎样在圆柱边界上给出适当的附着条件的数值方法。在算例中雷诺数分别取200、550、3000,得到了不定常边界层分离,二次涡等复杂的物理现象,这些数值结果与近年实验结果[2]是一致的。     

Entropic, LES and boundary conditions in lattice Boltzmann simulations of turbulence

Large scale (1600³-grid) entropic lattice Boltzmann (ELB) simulations are performed on the 27-bit model at sufficiently high Reynolds numbers to find intermittency corrections to the Kolmogorov k ^-5/3 inertial spectrum. Even though the transport coefficients in ELB and in the Large Eddy Simulation (LES) lattice Boltzmann schemes have very different origins, there are strong similarities in their turbulence statistics from 512³-grid simulations. A new LB moment-space boundary condition algorithm is tested on the 2D backstep problem, with excellent agreement with experimental data even up to a Reynolds number of 800.