Adsorption of modified dextrins on talc: effect of surface coverage and hydration water on hydrophobicity reduction

The adsorption of three modified dextrins on the basal plane of talc has been studied using in situ tapping mode atomic force microscopy (TMAFM). The images have been used to determine the layer thickness and coverage of the adsorbed polymers. Adsorption isotherms of the polymers on talc particles were also determined using the depletion technique. Values of the adsorbed amount at equilibrium were compared with the volume of adsorbed material as determined using in situ TMAFM, revealing the presence of significant amounts of hydration water in the adsorbed layer structure. This deduction was confirmed by comparing in and ex situ TMAFM images of the adsorbed dextrins. The effect of layer thickness, coverage, and hydration water content on the contact angle of talc particles treated with polymer was investigated using the Washburn method and the equilibrium capillary pressure (ECP) method. Distinct correlations were observed between adsorbed layer properties and the measured contact angles, with the ECP measurements especially highlighting the effect of the adsorbed polymer layer hydration water. The implications for the performance of the modified dextrins in flotation are discussed.     

The role of mineral surface chemistry in modified dextrin adsorption

The adsorption of two modified dextrins (phenyl succinate dextrin--PS Dextrin; styrene oxide dextrin--SO Dextrin) on four different mineral surfaces has been studied using X-ray photoelectron spectroscopy (XPS), in situ atomic force microscopy (AFM) imaging, and captive bubble contact angle measurements. The four surfaces include highly orientated pyrolytic graphite (HOPG), freshly cleaved synthetic sphalerite (ZnS), and two surfaces produced through surface reactions of sphalerite: one oxidized in alkaline solution (pH 9, 1 h immersion); and one subjected to metal ion exchange between copper and zinc (i.e. copper activation: exposed to 1×10(-3) M CuSO(4) solution for 1 h). XPS measurements indicate that the different sphalerite surfaces contain varying amounts of sulfur, zinc, oxygen, and copper, producing substrates for polymer adsorption with a range of possible binding sites. AFM imaging has shown that the two polymers adsorb to a similar extent on HOPG, and that the two polymers display very different propensities for adsorption on the three sphalerite surface types, with freshly cleaved sphalerite encouraging the least adsorption, and copper activated and oxidized sphalerite encouraging significantly more adsorption. Contact angle measurements of the four surfaces indicate that synthetic sphalerite has a low contact angle upon fracture, and that oxidation on the timescale of one hour substantially alters the hydrophobicity. HOPG and copper-activated sphalerite were the most hydrophobic, as expected due to the carbon and di/poly-sulfide rich surfaces of the two samples, respectively. SO Dextrin is seen to have a significant impact on the wettability of HOPG and the surface reacted sphalerite samples, highlighting the difficulty in selectively separating sphalerite from carbonaceous unwanted minerals in flotation. PS Dextrin has the least effect on the hydrophobicity of the reacted sphalerite surfaces, whilst still significantly increasing the wettability of graphite, and thus has more potential for use as a polymer depressant in this separation.     

In situ ATR FTIR study of dextrin adsorption on anatase TiO2

The adsorption of two dextrin-based polymers, a regular wheat dextrin (TY) and a carboxymethyl-substituted (CM) dextrin, onto an anatase TiO(2) particle film has been studied using in situ attenuated total reflection (ATR) FTIR spectroscopy. Infrared spectra of the polymer solutions and the polymer adsorbed at the anatase surface were acquired for two solution conditions: pH 3 and pH 9; below and above the isoelectric point (IEP) of anatase, respectively. Comparison of the polymer solution spectra and the adsorbed layer spectra highlighted a number of spectral differences that were attributed to involvement of the carboxyl group of CM Dextrin interacting with the anatase surface directly and the adsorption of oxidized dextrin chains in the case of regular dextrin (TY) at high pH. The adsorption/desorption kinetics were determined by monitoring spectral peaks of the pyranose ring of both polymers. Adsorption equilibrium was not established for Dextrin TY for many hours, whereas CM Dextrin reached equilibrium in its adsorption within 60 min. The extent of desorption of Dextrin TY (observed by flowing a background electrolyte dextrin-free solution) was extensive at both pH values, which reflects the poor affinity and binding of the polymer on anatase. In contrast, CM Dextrin underwent almost no desorption, indicating a high affinity between the carboxyl groups of the polymer and the anatase surface.     

Flotation de-inking studies using model hydrophobic particles and non-ionic dispersants

A series of non-ionic alcohol ethoxylated surfactants (with HLB within the range of 11.1–12.5) were used as dispersants during flotation of mondisperse hydrophobised silica particles (representing ink particles) in de-inking formulations. Laboratory scale flotation experiments, contact angle, dynamic surface tension and thin film drainage experiments were carried out. The reduction in dynamic surface tension at the air/solution interface (which is dependent on the adsorption kinetics) followed the order C₁₀E₆>C₁₂E₈≈C₁₂E₆>C₁₄E₆ and these values were lower than sodium oleate, which is commonly used in de-inking systems. In addition the non-ionics adsorbed on the hydrophobised silica particles reducing the contact angle. These results indicated that the non-ionic surfactant with the highest CMC (C₁₀E₆) gave (a) the highest rate of adsorption at the air/solution interface (b) the froth with the greatest water content and higher froth volume (c) the lowest reduction in contact angle and (d) the highest flotation efficiency at concentrations above the CMC. It was also observed that flotation occurred, in spite of the fact that thin-film measurements indicated that the adsorption of non-ionic at the air/solution and silica/solution interfaces reduced the hydrophobicity of the particles, as indicated by an increase in stability of the aqueous thin film between the particle and air-bubble. This result suggests that the bubble-ink particle captures mechanism (occurring through rupture of the thin aqueous film separating the interfaces) is not the only mechanism controlling the flotation efficiency and that other parameters (such as the kinetics of surfactant adsorption, foaming characteristics, and bubble size) need to be taken into account. The kinetics is important with respect to the rate of adsorption of surfactant to both interfaces. Under equilibrium conditions, this may give rise to repulsive steric forces between the air-bubble and the particles (stable aqueous thin-films). However, a lower amount of surfactant adsorbed at a freshly formed air bubble or inkparticle (caused by slow adsorption rates) will produce a lower steric repulsive force allowing effective collection of particles by the bubble. Also, it was suggested that the influence of alcohol ethoxylates on bubble-size could effect the particle capture rate and mechanical entrainment of particles in an excessively buoyant froth, which will also play an important role in the flotation recovery.     

Adsorption of Ethyl(hydroxyethyl)cellulose onto Silica Particles: The Role of Surface Chemistry and Temperature

The adsorption characteristics of an ethyl(hydroxyethyl)cellulose (EHEC) polymer onto colloidal silica particles from aqueous solution have been investigated. The influence of solution temperature and the silica surface chemistry on EHEC adsorption isotherms and adsorbed layer thicknesses have been determined in an attempt to elucidate the mechanisms of adsorption. As the hydrophobicity of the silica particles are increased by physical and chemical treatment, the plateau EHEC adsorbed amount increased, while the corresponding adsorbed layer thickness decreased. The estimated free energy of adsorption (DeltaG(o)(ads)) was shown to be dependent on the silica surface chemistry, but did not correlate directly with silica's advancing water contact angle and suggests that EHEC adsorption is not directly controlled by hydrophobicity alone. As the solution temperature increased from 18 to 37 degrees C, the plateau coverage of EHEC increased while the layer thickness generally decreased, this concurred with a reduction in the solvency. For hydrophilic and dehydrated silica particles, DeltaG(o)(ads) decreased in magnitude with increasing temperature, whereas for chemically treated silica, DeltaG(o)(ads) increased with temperature. These findings are discussed with respect to the specific interactions between EHEC segments and surface sites, which control the adsorption mechanisms of cellulose polymers. Copyright 2000 Academic Press.     

Surface Forces in Wetting Films

Reviewed are theoretical and experimental results of Russian and foreign researchers of the surface forces acting in asymmetric system, wetting films contacting with the condensed phase on the one side and with the gaseous phase or own vapor on the other side. Wetting films play an important role in such phenomena as wetting and spreading, flotation, polymolecular adsorption, evaporation of liquids from porous bodies, and capillary condensation. Disjoining pressure isotherms of wetting films determine the wetting conditions and the values of forming contact angles. The mechanisms of film stability, rupture, and coalescence are discussed based on the theory of surface forces. The properties of the films of nonpolar liquids and liquid mixtures; polymolecular adsorption films of polar liquids; as well as wetting films of aqueous electrolyte solutions, surfactants and polymers are analyzed systematically.     

An in situ ATR-FTIR study of polyacrylamide adsorption at the talc surface

The adsorption of a low molecular weight unmodified polyacrylamide (Polymer-N) and a hydroxyl-substituted polyacrylamide (Polymer-H) onto talc was studied using in situ particle film ATR-FTIR spectroscopy in the multiple internal reflection mode. Spectra of the adsorbed polymer were collected as a function of increasing concentration and as a function of time. Measurement of the peak intensities of the adsorbed polymer allowed adsorption isotherms and adsorption kinetics to be determined for both polymers. Langmuir adsorption isotherm analysis of in situ data yielded Gibbs free energies of adsorption (deltaG0(ads)) for Polymer-N and Polymer-H of -44.5 and -45.7 kJ/mol, respectively, which correlate well with similar values determined from ex situ adsorption isotherms. Kinetic analysis indicated that the adsorption of both polymers was a pseudo-first-order process. The apparent rate constants for Polymer-N and Polymer-H were 0.10 and 0.15 min(-1), respectively. Absence of spectral shifts in the spectra of adsorbed polymer is indicative of a hydrophobic interaction between the polyacrylamides and the talc surface.     

Preparation of Langmuir/Blodgett-cellulose Surfaces by Using Horizontal Dipping Procedure. Application for Polyelectrolyte Adsorption Studies Performed with QCM-D

A method of preparing model cellulose surfaces by the Langmuir–Blodgett (LB) technique with horizontal dipping procedure has been developed. The primary aim for the use of these surfaces was adsorption studies performed with the quartz crystal microbalance with dissipation (QCM-D) instrument. Hydrophobised cellulose (trimethylsilyl cellulose, TMSC) was deposited on the hydrophobic, polystyrene-coated QCM-D crystal. After 15 dipping cycles, the TMSC film fully covers the crystal surface. TMSC can easily be hydrolysed back to cellulose with acid hydrolysis. With this method a smooth, rigid, thin and reproducible cellulose film was obtained. Its morphology, coverage, chemical composition and wetting was further characterised using atomic force microscopy (AFM), X-Ray photoelectron spectroscopy (XPS), and contact angle measurements. The swelling behaviour and the stability of the cellulose film in aqueous solutions at different ionic strengths were studied using the QCM-D instrument. The swelling/deswelling properties of the cellulose film were those expected of polyelectrolytes with low charge density; some swelling occurred in pure water and the swelling decreased when the ionic strength was increased. No significant layer softening was detected during the swelling. The effect of electrolyte concentration and polymer charge density on the adsorption of cationic polyelectrolytes on the cellulose surface was also investigated. At low electrolyte concentration less of the highly charged PDADMAC was adsorbed as compared to low charged C-PAM. The adsorbed amount of PDADMAC increased with increasing ionic strength and a more compact layer was formed while the effect of electrolyte concentration on the adsorption of C-PAM was not as pronounced.     

Nanoparticle flotation collectors II: the role of nanoparticle hydrophobicity

The ability of polystyrene nanoparticles to facilitate the froth flotation of glass beads was correlated to the hydrophobicity of the nanoparticles. Contact angle measurements were used to probe the hydrophobicity of hydrophilic glass surfaces decorated with hydrophobic nanoparticles. Both sessile water drop advancing angles, θ(a), and attached air bubble receding angle measurements, θ(r), were performed. For glass surfaces saturated with adsorbed nanoparticles, flotation recovery, a measure of flotation efficiency, increased with increasing values of each type of contact angle. As expected, the advancing water contact angle on nanoparticle-decorated, dry glass surfaces increased with surface coverage, the area fraction of glass covered with nanoparticles. However, the nanoparticles were far more effective at raising the contact angle than the Cassie-Baxter prediction, suggesting that with higher nanoparticle coverages the water did not completely wet the glass surfaces between the nanoparticles. A series of polystyrene nanoparticles was prepared to cover a range of surface energies. Water contact angle measurements, θ(np), on smooth polymer films formed from organic solutions of dissolved nanoparticles were used to rank the nanoparticles in terms of hydrophobicity. Glass spheres were saturated with adsorbed nanoparticles and were isolated by flotation. The minimum nanoparticle water contact angle to give high flotation recovery was in the range of 51° < θ(np(min)) ≤ 85°.     

The effect of polymer adsorption on the wetting properties of partially hydrophobized magnetite

Upon reverse flotation of iron ore, the surface of the iron ore concentrate may become partially hydrophobized due to adsorption of flotation collector, which is facilitated by the calcium ions present in the process water. Hydrophobic areas on the concentrate surface may introduce problems in subsequent pelletization of the concentrate. A possible way to restore the wettability of the surface could be by modifying the surface with a hydrophilic polymer. The effect of hydrophilic polymers of different types, viz. cationic, anionic, and non-ionic, on the wettability of the magnetite surface after adsorption of a surfactant was investigated. Although all the polymers could adsorb on magnetite at pH 8.5, the contact angle measurements revealed that only anionic ammonium polyacrylate could decrease the contact angle of synthetic magnetite after surfactant adsorption to a level close to that of as-synthesized magnetite. Such effect was probably achieved due to shielding of the hydrophobic surfactant chains from the aqueous phase by hydrophilic polyacrylate molecules. The fact that polyacrylate adsorption on magnetite occurred via calcium ions makes polyacrylate suitable for application in calcium-rich process water. The results presented in this work illustrate that ammonium polyacrylate could be successfully used to improve the wettability of magnetite after adsorption of surfactants.     

Adsorption and thermoresponsive behavior of poly(N-isopropylacrylamide-co-N,N'-cystaminebisacrylamide) thin films on gold

We describe the synthesis of thermoresponsive polymers made from N-isopropylacrylamide and varying amounts of a thiol-containing co-monomer, N,N'-cystaminebisacrylamide (P(NIPAm-co-CBAm)). Infrared spectroscopy revealed a backbone similar to that seen with pure PNIPAm. UV-vis spectroscopy showed that P(NIPAm-co-CBAm) undergoes a thermoresponsive phase transition around 32 degrees C in aqueous solution. The presence of the thiol groups enabled the polymer to adsorb onto gold surfaces. Following adsorption onto a gold surface, X-ray photoelectron spectroscopy showed a carbon/gold atomic ratio of 0.93 for a sample without CBAm and a ratio of 1.61 for a P(NIPAm-co-CBAm) sample with 0.20% CBAm. Quartz crystal microbalance (QCM) analysis showed increases in the mass of polymer adsorbed when the CBAm content in the polymer increased. The thermoresponsive behavior of the thin films on gold was investigated with contact angle and dissipative QCM analysis. Contact angles were measured for polymer films at both 25 and 60 degrees C. The largest temperature-induced alteration in the contact angle was seen with the 1.00% CBAm sample. Similarly, QCM-D results showed a significantly greater change in frequency and dissipation following a temperature change when CBAm was present than in pure NIPAm polymers.     

Molecular dynamics simulations of layer-by-layer assembly of polyelectrolytes at charged surfaces: effects of chain degree of polymerization and fraction of charged monomers

We performed molecular dynamics simulations of the electrostatic assembly of multilayers of flexible polyelectrolytes at a charged surface. The multilayer build-up was achieved through sequential adsorption of oppositely charged polymers in a layer-by-layer fashion from dilute polyelectrolyte solutions. The steady-state multilayer growth proceeds through a charge reversal of the adsorbed polymeric film which leads to a linear increase in the polymer surface coverage after completion of the first few deposition steps. Moreover, substantial intermixing between chains adsorbed during different deposition steps is observed. This intermixing is consistent with the observed requirement for several deposition steps to transpire for completion of a single layer. However, despite chain intermixing, there are almost perfect periodic oscillations of the density difference between monomers belonging to positively and negatively charged macromolecules in the adsorbed film. Weakly charged chains show higher polymer surface coverage than strongly charged ones.     

Adsorption of hydrophobically modified poly(acrylamide)-co-(acrylic acid) on an amino-functionalized surface and its response to the external solvent environment

The adsorption of hydrophobically modified poly(acrylamide)-co-(acrylic acid), designated as PAM-C14-AA (x%) (x = 5, 10, 20, representing the mole percent of acrylic acid units), at an amino-functionalized silicon surface was studied. The effect of polymer charge density was determined by varying the acrylic acid content of the copolymer. Characteristics of the adsorbed layer were evaluated by atomic force microscopy, water contact angle measurements, and X-ray photoelectron spectroscopy. The results showed that the adsorption behavior of PAM-C14-AA (x%) is influenced by the balance among the electrostatic, hydrogen-bonding, and hydrophobic interactions. Adjusting the solution pH and polymer charge density significantly affects the morphology and thickness of the adsorbed film. Furthermore, it was found that the adsorbed PAM-C14-AA undergoes conformational rearrangements when the surface is wetted by selected organic solvents. The resultant morphology and wettability of the films indicated that the different affinities of the solvents for different segments of PAM-C14-AA (x%) can be considered to be the possible cause of the conformational rearrangements of adsorbed polymer.     

Study on the interaction between anionic and cationic latex particles and Portland cement

The interaction between organic latex polymers and the surface of hydrating cement was investigated by measuring the zeta potential and adsorbed amount of polymer on cement. First, differently charged model latex particles were synthesized in aqueous media by well-known emulsion polymerization technique. The latex polymers were characterized by differential scanning calorimetry (DSC), dynamic light scattering (DLS) and environmental scanning electron microscopy (ESEM). Electrokinetic latex surface properties were investigated by means of streaming potential measurements using a particle charge detector (PCD). It is shown that the anionic latexes adsorb a considerable amount of Ca²⁺ from the cement pore solution. Next, adsorption of the latex polymers on the surface of hydrating cement was confirmed by zeta potential measurements using the electroacoustic method. A water to cement ratio in the cement paste as low as 0.5 was studied, representing actual conditions in mortar and concrete. Additionally, adsorption isotherms were determined in a sedimentation test using the depletion method. For all latex polymers, Langmuir type adsorption isotherms were found. The latex dosages required to achieve saturated adsorption on the cement surface obtained from zeta potential measurements correspond well with those determined in the sedimentation test. Electron microscopy photographs confirm that the charged latex polymers adsorb selectively on surface areas of hydrating cement showing opposite charge. This way, domains of organic latex polymers exist on the cement surface. They provide adhesion between the inorganic cement matrix and the organic polymer film formed later on by particle coalescence as a result of cement hydration and drying.     

Selective protein adsorption on a phase-separated solvent-cast polymer blend

Polymer-based biomedical devices are growing increasingly sophisticated as compositions evolve toward copolymers and blends in order to satisfy complex design criteria. Such polymers afford opportunities for both micro- and macrophase separation at nano- and micro-length scales and raise questions concerning the role of heterogeneous surface morphology on protein adsorption. Adsorbed protein layers play a critical role in mediating the interaction of cells with polymer surfaces, and both understanding and controlling protein adsorption is assuming greater significance in the development of surfaces with enhanced physiological compatibility. Here we study the short-time adsorption of ferritin, a model protein highly resistant to denaturation and easily imaged in the transmission electron microscope (TEM), onto a phase-separated homopolymer blend of polycaprolactone (PCL) and a polycarbonate derived from desaminotyrosyl-tyrosine dodecyl ester (PDTD). At physiological pH, ferritin selectively adsorbs onto the PDTD phase at a surface density approximately three times greater than that on the PCL phase. By decreasing the pH below ferritin's isoelectric point so its average charge becomes positive, the selective adsorption disappears and the surface density of adsorbed ferritin becomes independent of the phase separation. We attribute the selectivity to the electrostatic repulsion between ferritin and hydrolytically charged PCL, both of which will have a net negative charge at physiological pH. To perform these experiments, we solvent-cast ultrathin polymer films onto dissolvable salt substrates, and we characterize the morphology by TEM imaging and quantitative spatially resolved electron energy-loss spectroscopy (EELS). We find that the film morphology depends strongly on such processing-related variables as the solvent evaporation rate and the nature of the surface in contact with the polymer film during casting. The adsorption of ferritin depends on whether the film is phase-separated as well as to which surface of the film the protein solution is exposed, and these findings suggest that seemingly small variations in polymer processing that influence both the bulk and surface morphology can have a profound effect on the short-time protein adsorption.     

Shear-induced coalescence of oil-in-water Pickering emulsions

Thermodynamic treatment of thin liquid films in Part III of this series was applied to foam films stabilized by sodium dodecyl sulfate. Miscibility of sodium chloride and sodium dodecyl sulfate in the adsorbed films at the film surfaces and transition between the black films were studied by measuring film thickness and contact angle. A discontinuous change in the thickness and a break on the contact angle vs. concentration curve appeared at the transition. Judging from the phase diagram of adsorption, sodium chloride and sodium dodecyl sulfate are a little miscible in the adsorbed films. The miscibility was ascribed to specific interaction between sodium ion and dodecyl sulfate ion in the adsorbed films. The miscibility in an adsorbed film was compared between the film surface and meniscus and between the common black and Newton black films.     

Determination of surface area and porosity of small, nanometer-thick films by quartz crystal microbalance measurement of gas adsorption

The Brunauer-Emmett-Teller (BET) surface area of 15 nm-thick films made of TiO2/polyelectrolyte bilayer was determined by quartz crystal microbalance (QCM) measurement of N2 and Ar adsorption isotherms at 77 K. The measurements were carried out using a home-built vacuum chamber that includes built-in 9 MHz QCM and cryostat units. As little as 1 ng of the adsorbed gas could be detected, and the BET surface area of a flat Au film (ca. 0.5 cm2) on an oscillator was determined within an experimental error of +/-5%. The titania/polymer composite film gives N2 and Ar adsorption isotherms consisting of a less-pronounced type-I curve and a break at around p/p0 = 0.7. This behavior is ascribed to the presence of irregular micropores and 6 nm phi-mesopores in the composite film. An analysis of the isotherms shows that the porosity of the composite film is about 12%, which is much smaller than that of bulk titania gel powder. The greater density appears to be related to the reported superior properties (robustness and resistance to electrical breakdown) of the organic/inorganic multilayer film. We conclude that the QCM-based, high-precision measurement of gas adsorption is a powerful tool for investigation of the detailed morphology of nanometer-thick films.     

Spreading, evaporation, and contact line dynamics of surfactant-laden microdrops

An optical technique based on the reflectivity measurements of a thin film was used to experimentally study the spreading, evaporation, contact line motion, and thin film characteristics of drops consisting of a water-surfactant (polyalkyleneoxide-modified heptamethyltrisiloxane, called superspreader) solution on a fused silica surface. On the basis of the experimental observations, we concluded that the surfactant adsorbs primarily at the solid-liquid and liquid-vapor interfaces near the contact line region. At equilibrium, the completely wetting corner meniscus was associated with a flat adsorbed film having a thickness of approximately 31 nm. The calculated Hamaker constant, A = -4.47 x 10(-)(20) J, shows that this thin film was stable under equilibrium conditions. During a subsequent evaporation/condensation phase-change process, the thin film of the surfactant solution was unstable, and it broke into microdrops having a finite contact angle. The thickness of the adsorbed film associated with the drops was lower than that of the equilibrium meniscus. The drop profiles were experimentally measured and analyzed during the phase-change process as the contact line advanced and receded. The apparent contact angle, the maximum concave curvature near the contact line region, and the convex curvature of the drop increased as the drop grew during condensation, whereas these quantities decreased during evaporation. The position of the maximum concave curvature of the drop moved toward the center of the drop during condensation, whereas it moved away from the center during evaporation. The contact line velocity was correlated to the observed experimental results and was compared with the results of the drops of a pure alcohol. The experimentally obtained thickness profiles, contact angle profiles, and curvature profiles of the drops explain how the surfactant adsorption affects the contact line motion. We found that there was an abrupt change in the velocity of the contact line when the adsorbed film of the surfactant solution was just hydrated or desiccated during the phase-change processes. This result shows the effect of vesicles and aggregates of the surfactant on the shape evolution of the drops. For these surfactant-laden water drops, we found that the apparent contact angle increased during condensation and decreased during evaporation. However, for the drop of a pure liquid (n-butanol and 2-propanol) the apparent contact angle remained constant at a constant velocity during condensation and evaporation. The contact line was pinned during the evaporation and spreading of the surfactant-laden water drops, but it was not pinned for a drop of a pure alcohol (self-similar shape evolution).     

Hydrophobic mechanochemical treatment of metallic surfaces wettability measurements as a means of assessing homogeneity

Hydrophobicity, lubrication and anticorrosion properties of steel substrates have been obtained by a deposition of thin film (i.e. by mechanochemical treatment) at room conditions. Stearic acid and paraffin were chosen as reactive molecules. Different abrasive powders were selected to generate active sites on the treated surfaces for adsorption of the reactive molecules and then, the results were compared. The surfaces were analyzed by reflection-absorption infrared spectroscopy (RAIRS). The results emphasize that, a thick layer of mixed stearic acid/paraffin was deposited onto the metallic surface after the treatment. After hexane rinsing we could only detect a very thin layer of oriented stearic acid molecules chemically adsorbed onto the metallic surface and which engages strong interactions with it. Whereas, RAIRS only provides molecular analysis, the XPS technique was complementary for discriminating the different surfaces. It was possible to show differences in thickness as well as in coverage according to the size and shape of abrasive particles. Furthermore, we could conclude that deposit layer is not uniform. Defects were always present and were dependent on abrasive powders used. Then wettability was assessed as a way to test the homogeneity of thin films generated by the mechanochemical treatment. In agreement with theoretical data, receding contact angle was very dependent on the defects in the deposited film. If holes or aggregates were increased in the deposit layer, the receding contact angle was decreased while advancing contact angles and equilibrium contact angles remained constant. A very important point for technological applications was that the homogeneity of the deposited film was governed by abrasive powder involved in mechanochemical treatment and contact angle values were a direct measurement of the homogeneity of surfaces generated by mechanochemical treatment.     

Surface engineering of styrene/PEGylated‐fluoroalkyl styrene block copolymer thin films

A series of diblock copolymers prepared from styrenic monomers was synthesized using atom transfer radical polymerization. One block was derived from styrene, whereas the second block was prepared from a styrene modified with an amphiphilic PEGylated‐fluoroalkyl side chain. The surface properties of the resulting polymer films were carefully characterized using dynamic contact angle, XPS, and NEXAFS measurements. The polymer morphology was investigated using atomic force microscope and GISAXS studies. The block copolymers possess surfaces dominated by the fluorinated unit in the dry state and a distinct phase separated microstructure in the thin film. The microstructure of these polymers is strongly influenced by the thin film structure in which it is investigated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 267–284, 2009