Surface forces in wetting films

A short review of various components of surface forces acting in a non-symmetrical system such as wetting films is presented here. Experimental results are compared with modified DLVO theory, which includes, besides dispersion and electrostatic, structural (solvation) forces caused by a change in liquid structure in conditions of confined geometry. The peculiarities of disjoining pressure isotherms and conditions of the film stability of non-polar and polar simple liquids, as well as of aqueous solutions of electrolytes and surfactants, are systematically considered from a historical perspective.     

Hydrophobic forces in the foam films stabilized by sodium dodecyl sulfate: effect of electrolyte

Further studies of the hydrophobic force in foam films were carried out, including the effect of added inorganic electrolyte. We used a thin film balance of Scheludko-Exerowa type to obtain the disjoining pressure isotherms of the foam films stabilized by 10(-4) M sodium dodecyl sulfate in varying concentrations of sodium chloride. The results were compared with the disjoining pressure isotherms predicted from the extended Derjaguin-Landau-Verwey-Overbeek theory, which considers contributions from hydrophobic force in addition to those from double layer and van der Waals dispersion forces. The double layer forces were calculated from the surface potentials (psi s) obtained using the Gibbs adsorption equation and corrected for the counterion binding effect, while the dispersion forces were calculated using the Hamaker constant (A232) of 3.7 x 10(-20) J. The hydrophobic forces were calculated from the equilibrium film thickness as described previously. The predicted disjoining pressure isotherms were in good agreement with the experimental ones. It was found that the hydrophobic force is dampened substantially by the added electrolyte.     

Properties of foam films stabilized with tetraethylammonium perfluorooctane-sulfonate

Properties of single foam films prepared with tetraethylammonium perfluorooctane-sulfonate (TAPOS) were studied. Film thickness was measured as a function of NH₄Cl concentration in the film forming solution. The dependence of the film disjoining pressure versus the film thickness (disjoining pressure isotherms) and the mean lifetime of the films were studied. The dependence of the film thickness on the electrolyte concentration showed the presence of an electrostatic double layer at the film surfaces. The electrostatic double layer component of the disjoining pressure was screened at a NH₄Cl concentration higher than 0.2 M where Newton black films (NBFs) of 6 nm thickness were formed. These films are bilayers of amphiphile molecules and contain almost no free water. The disjoining pressure isotherms of the foam films formed with 0.001 M TAPOS were measured at two different NH₄Cl concentrations (0.005 and 0.0005 M). The Deryaguin-Landau-Verwey-Overbeek (DLVO) theory describes well the isotherms with an electrostatic double layer potential of ∼140 mV. The mean lifetime, a measure of the stability of the NBFs, was measured depending on surfactant concentrations. The observation of NBF was possible above a minimum TAPOS concentration of 9.4 × 10⁻⁵ M. Above this concentration, the lifetime increases exponentially. The dependence of the film lifetime on surfactant concentration is explained by the theory for NBF-rupture by nucleation mechanism of formation of microscopic holes.     

Interaction forces in thin liquid films stabilized by hydrophobically modified inulin polymeric surfactant. 1. Foam films

Using the interferometric method of Scheludko-Exerowa for investigation of foam films, we have obtained results using a hydrophobically modified inulin polymeric surfactant (INUTEC SP1). Measurements were carried out at constant INUTEC SP1 concentration of 2 x 10(-)(5) mol.dm(-)(3) and at various NaCl concentrations (in the range 1 x 10(-)(4) to 2 mol.dm(-)(3)). At constant capillary pressure of 50 Pa, the film thickness decreased gradually with an increase in NaCl concentration up to 10(-)(2) mol.dm(-)(3) NaCl above which the film thickness remains virtually constant at about 16 nm. This reduction in film thickness with an increase in NaCl concentration is due to the compression of the double layer and at the critical electrolyte concentration (C(el,cr) = 10(-)(2) mol.dm(-)(3)) the electrostatic component of the disjoining pressure is completely screened and the remaining pressure is due to the steric interaction between the adsorbed polymer layers. Disjoining pressure-thickness (Pi-h) isotherms were obtained at C(el) < C(el,cr) (10(-)(4) - 10(-)(3) mol.dm(-)(3)) and C(el) > C(el,cr) (0.5, 1, and 2 mol.dm(-)(3)). In the first case, the disjoining pressure isotherms could be fitted using the classical DLVO theory, Pi = Pi(el) + Pi(vw), and using the constant charge model. At C(el) > C(el,cr), the main repulsion is due to the steric interaction between the polyfructose loops that exist at the air-water interface, i.e., Pi = Pi(st) + Pi(vw). Under these conditions, there is a sharp transition from DLVO to non-DLVO forces. In the latter case, the interaction could be described using the de Gennes' scaling theory. This gave an adsorbed layer thickness of 6.5 nm which is in reasonable agreement with the values obtained at the solid-solution interface. The Pi-h isotherms showed that these foam films are not very stable and they tend to collapse above a critical capillary pressure (of about 1 x 10(3) Pa), and these results could be used to predict the foam stability.     

Influence of electrolytes on the dynamic surface tension of ionic surfactant solutions: expanding and immobile interfaces

Here, we derive analytical asymptotic expressions for the dynamic surface tension of ionic surfactant solutions in the general case of nonstationary interfacial expansion. Because the diffusion layer is much wider than the electric double layer, the equations contain a small parameter. The resulting perturbation problem is singular and it is solved by means of the method of matched asymptotic expansions. The derived general expression for the dynamic surface tension is simplified for the special case of immobile interface and for the maximum bubble pressure method (MBPM). The case of stationary interfacial expansion is also considered. The effective diffusivity of the ionic surfactant essentially depends on the concentrations of surfactant and nonamphiphilic salt. To test the theory, the derived equations are applied to calculate the surfactant adsorption from MBPM experimental data. The results excellently agree with the adsorption determined independently from equilibrium surface-tension isotherms. The derived theoretical expressions could find application for interpreting data obtained by MBPM and other experimental methods for investigating interfacial dynamics.     

Investigation of the isotherms of the disjoining pressure of wetting films of binary nonionic solutions by the ellipsometric method

The paper deals with an experimental investigation into the influence of the second component on the thicknesses of the wetting films of a nonionic solvent. A technique has been developed for the production of pure, smooth, thin glass substrates for wetting liquid films.

The use of these glass substrates enabled us to exclude the influence on the experimental results of such noncontrollable factors as roughness and pollution of the substrate surface. The isotherms of the disjoining pressure of wetting films of a number of two-component mixtures of nonionic liquids on glass substrates were experimentally determined. The film thicknesses were measured by an ellipsometric method; the disjoining pressure for the film was preset by adjusting the pressure of solvent vapours. The results obtained demonstrate a qualitative agreement with the theory of the adsorption component of disjoining pressure developed by Derjaguin and Churaev.

It is also shown that even very small additions of a polar substance to a nonpolar solvent may cause a marked change in the thickness of films. In addition to adopting the theory of the adsorption component of disjoining pressure, certain assumptions are made about the formation of the structural component resulting from the addition of a polar component to quantitatively describe the results obtained. The contribution of the adsorption and structural components of disjoining pressure to the stability of films of solution is estimated.     

Evidence of surface charge at the air/water interface from thin-film studies on polyelectrolyte-coated substrates

The stability of thin water films on silicon substrates coated with cationic and anionic polyelectrolytes was investigated by the thin film pressure balance technique. Depending on the surface charge of the substrate, the water films are either stable (on negatively charged wafers) or rupture rapidly (on positively charged wafers). It is supposed that this behavior is due to a negative surface charge of the free water surface. The underlying assumption that the films' stability is due to electrostatic interactions is supported by measurements of the disjoining pressure on silicon wafers with a native oxide layer, which indicates a decrease of the film thickness, and thus decreasing repulsive interaction between the two film interfaces, with increasing ionic strength.     

Mixed solutions of anionic and zwitterionic surfactant (Betaine): surface-tension isotherms, adsorption, and relaxation kinetics

Here, we present experimental surface-tension isotherms of mixed solutions of two surfactants, sodium dodecyl sulfate (SDS) and cocoamidopropyl betaine (Betaine), measured by means of the Wilhelmy plate method. The kinetics of surface-tension relaxation exhibits two characteristic time scales, which have been distinguished to determine correctly the equilibrium surface tension. The transition from the zwitterionic to the cationic form of Betaine is detected by surface-tension measurements. Synergistic dependence of the critical micellization concentration on the composition of the surfactant blend is established. The experimental surface-tension isotherms are fitted by means of the two-component van der Waals model, and an excellent agreement between theory and experiment was achieved. Having determined the parameters of the model, we calculated different properties of the mixed surfactant adsorption layer at various concentrations ofSDS, Betaine, and salt. Such properties are the adsorptions ofthe two surfactants, the surface dilatational elasticity, the occupancy of the Stern layer by bound counterions, the surface electric potential, and so forth. In particular, the addition of a small amount of Betaine to SDS significantly increases the surface elasticity. The results could be further applied to predict the thickness and stability of foam films or the size of the rodlike micelles in the mixed solutions of SDS and Betaine.     

Headgroup and hydrocarbon tail effects on the surface tension of sugar-based surfactant solutions

Measurements of surface tension isotherms were conducted for water solutions of pure and mixed n-decyl-beta-d-glucopyranoside (C(10)-Glu) and n-decyl-beta-d-maltopyranoside (C(10)-Mal) surfactants. By applying the Gibbs surface tension equation, the surface densities of Glu and Mal were derived for different compositions and concentrations. The surface fractions were compared with theoretically calculated values where the headgroups were modeled as hard disks. Satisfactory agreement was found for hard-disk sizes of 22.9 and 11.3 A(2) in the case of a 1:1 mixture. The results of the hard-disk calculations were employed to estimate the configurational free energy of the n-decyl-hydrocarbon chain. The results obtained agree well with previous calculations for the n-dodecyl chain. Comparison with n-dodecyl beta-d-maltopyranoside (C(12)-Mal) indicated a further contribution, with the longer hydrocarbon chain giving rise to a higher surface tension in good agreement with data for hydrocarbon liquids. Furthermore, the interpenetration of the headgroup into the hydrocarbon film was studied by means of comparing surface-tension data for n-decyl- and n-dodecyl-ethylene-oxide-based surfactants and n-decyl- and n-dodecyl-beta-d-thiomaltopyranosides (C(10)-S-Mal and C(12)-S-Mal, respectively) and -maltopyranosides. It was found that lengthening the tetra(etylene oxide) chain by one segment affects the surface tension only marginally, indicating little interpenetration of the additional ethylene-oxide group into the hydrocarbon film. For the thiomaltosides, however, the corresponding effect was found to be remarkably high.     

A disjoining pressure study of foam films stabilized by mixtures of nonionic and ionic surfactants

Studying the disjoining pressure Pi as a function of the film thickness h (Pi-h curves) of foam films stabilized by ionic and nonionic surfactants, one finds that the surface charge density q0 of films stabilized by ionic surfactants increases with increasing surfactant concentration, while the opposite holds true for nonionic surfactants. Thus, it should be possible to tune the surface charge density with mixtures of nonionic and ionic surfactants. To address this question, we studied foam films stabilized by aqueous solutions of surfactant mixtures. The mixtures consisted of the nonionic beta-dodecylmaltoside (beta-C12G2) and the cationic dodecyl trimethylammonium bromide (C12TAB) with mixing ratios of beta-C12G2/C12TAB = 1:0, 50:1, 1:1, 1:50, 0:1. The addition of small amounts of C12TAB to beta-C12G2 first neutralizes the negative surface charge of the beta-C12G2 films and finally leads to a charge reversal from negatively to positively charged surfaces. On the other hand, by adding small amounts of beta-C12G2 to C12TAB, one observes the formation of stable CBFs which was also observed for the pure C12TAB. However, in contrast to the pure C12TAB, the resulting Pi-h curves for the mixtures cannot be described with the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory; the slope of the curves is too steep, and it barely changes with changing electrolyte concentration. A possible explanation for this observation will be given and discussed.     

Electrostatic and steric interactions in oil-in-water emulsion films from Pluronic surfactants

Stabilization of oil-in-water emulsion films from PEO-PPO-PEO triblock copolymers is described in terms of interaction surface forces. Results on emulsion films from four Pluronic surfactants, namely F108, F68, P104 and P65 obtained with the Thin Film Pressure Balance Technique are summarized. It is found that film stabilization is due to DLVO (electrostatic) and non-DLVO (steric in origin) repulsive forces. The charging of the oil/water film interfaces is related to preferential adsorption of OH(-) ions. This is confirmed by pH-dependent measurements of the equivalent film thickness (h(w)) at both constant capillary pressure and ionic strength. With reducing pH in the acidic region, a critical value (pH(cr,st)) corresponding to an isoelectric state of the oil/water film surfaces is found where the electrostatic interaction in the films is eliminated. At pH≤pH(cr,st), the emulsion films are stabilized only by steric forces due to interaction between the polymer adsorption layers. Disjoining pressure (Π) isotherms measured for emulsion films from all the four Pluronic surfactants used at pH相似文献   

Effect of introduced charge in cellulose gels on surface interactions and the adsorption of highly charged cationic polyelectrolytes

The interaction between cellulose surfaces in aqueous solution has been measured using colloidal probe microscopy. Cellulose thin films with varying charge through carboxyl group substitution were used in this study with the surface forces fit to DLVO theory. It was found that the surface potential increased, as expected, with increasing carboxyl substitution. Furthermore, for a given degree of substitution, the surface potential increased as a function of increasing pH. At low pH, the surface forces interaction were attractive and could be fit to the non-retarded Hamaker equation using a constant of 3 x 10(-21) J. At pH greater than 5, the force interactions were monotonically repulsive, regardless of the ionic strength of the solution for all charge densities of the cellulose thin films. The adsorption of polyDADMAC to these charged cellulose films was also investigated using the quartz crystal microbalance. It was found that for the low charge film, a low surface excess of PDADMAC was sensed and that the adsorbed conformation was essentially flat. However for the higher charged cellulose film, a spontaneous de-swelling was observed resulting in no possibility of quantitatively determining the sensed mass using QCM.     

A Model for Hydration Interactions between Apoferritin Molecules in Solution

We have studied how non-DLVO forces between molecules of the globular protein apoferritin in solution affect its osmotic second virial coefficient. A model explaining the effects of the solution ionic strength and pH on the interprotein interaction is developed, to give a physical interpretation of recently published experimental findings showing that the second virial coefficient of the protein apoferritin, supported by acetate buffer, goes through a minimum as a function of ionic strength. At low ionic strengths, the apoferritin second virial coefficient initially decreases with increasing sodium ion concentration, as DLVO theory predicts. However, non-DLVO hydration forces due to overlapping of the Stern layers of the protein molecules increase the second virial coefficient with further increase of sodium ion concentration, again as found experimentally at higher ionic strengths. The non-DLVO effect arises from ionic exchange between hydrogen and sodium ions at the protein surface. An adsorption shell of hydrated sodium ions forms around the protein molecules with increasing buffer concentration.     

Heteroaggregation in binary mixtures of oppositely charged colloidal particles

Heteroaggregation (or heterocoagulation) rate constants have been measured in mixtures of well-characterized colloidal particles of opposite charge with multiangle static and dynamic light scattering. This technique permits routine measurements of absolute heteroaggregation rate constants, also in the presence of homoaggregation. Particularly with multiangle dynamic light scattering, one is able to estimate absolute heteroaggregation rate constants accurately in the fast aggregation regime for the first time. Heteroaggregation rate constants have also been measured over a wide range of parameters, for example, ionic strength and different surface charge densities. Amidine latex particles, sulfate latex particles, and silica particles have been used for these experiments, and they were well characterized with respect to their charging and homoaggregation behavior. It was shown that heteroaggregation rate constants of oppositely charged particles increase slowly with decreasing ionic strength, and provided the surface charge is sufficiently large, the rate constant is largely independent of the surface charge. These trends can be well described with DLVO theory without adjustable parameters.     

Behaviour of wetting films of sodium hyaluronate saline solutions

The behaviour of wetting films of sodium hyaluronate (NaHA) saline solutions, at physiological conditions, is investigated using interferometry. Concentrations in the range of dilute and semi-dilute regimes were chosen to assess the role of bulk molecular interactions on the surface forces. The transition from dilute to semi-dilute solutions is known to occur at c*=0.59 mg mL(-1). Dilute solutions form stable films whose behaviour is explained by van der Waals interactions. For semi-dilute solutions, the disjoining pressure vs film thickness isotherms show branches attributed to stepwise thinning or film stratification, which is interpreted in terms of a network as predicted by the theory of semi-dilute polyelectrolyte solutions. The distance between branches is 16 nm for the NaHA concentration of 2 mg mL(-1) and 12 nm for the concentration of 3.5 mg mL(-1), in agreement with the calculated correlation lengths of the polymeric network. Since no experimental evidence exists for the presence of a stable network in the bulk, this tendency for self-association should be the result of the liquid confinement. To our knowledge, the existence of oscillatory disjoining pressure isotherms in the presence of excess salt was never observed for other polyelectrolyte solutions.     

黑膜厚度与膜表面张力关系的研究

用微干涉测量技术直接测定楔压等温线,研究了电解质浓度对阳离子表面活性剂TTAB在浓度大于cmc时形成黑膜厚度的影响及膜表面张力与溶液表面张力之间的差别.结果显示,黑膜厚度取决于楔压和电解质浓度,随着楔压的增加,液膜厚度减少至一定程度后几乎保持不变,表明黑膜类型的转化是阶跃式的,而电解质屏蔽了液膜两个表面电荷层间的排斥作用,故电解质浓度增加,液膜厚度变小.由楔压等温线得出的膜表面张力的结果说明一般黑膜的表面张力与溶液的表面张力并无明显差别.     

Surface properties of mixtures of surface-active sugar derivatives with ionic surfactants: theoretical and experimental investigations

Surface properties of systems that are mixtures of ionic surfactants and sugar derivatives-anionic surfactant sodium dodecyl sulfate and n-dodecyl-beta-D-maltoside (SDS/DM) and cationic surfactant dodecyltrimethylammonium bromide and n-dodecyl-beta-D-glucoside (DTABr/DG)-were investigated. The experimental results obtained from measurements of surface tension of mixtures with various ratio of ionic to nonionic components were analyzed by two independent theories. First is Motomura theory, derived from the Gibbs-Duhem equation, allowing for indirect evaluation of the composition of mixed monolayers and the Gibbs energies of adsorption, corresponding to mutual interaction between surfactants in mixed adsorbed film. As second theory we used our newly developed theoretical model of adsorption of ionic-nonionic surfactant mixtures. Using this approach, we were able to describe the experimental surface tension isotherms for mixtures of surface-active sugar derivatives and ionic surfactants. We obtained a good agreement with experimental data using the same set of model parameters for a whole range of studied compositions of a given surfactant mixture. The values of surface excess calculated from both theories agreed with each other with a reasonable accuracy. However, the newly developed model of adsorption of ionic-nonionic surfactant mixtures has the advantage of straightforward determination of surface layer composition. By the solution of equations of adsorption, one can obtain directly the values of surface excess of all components (surfactant ions, counterions, and nonionic surfactants molecules), which are present in the investigated system.     

Influence of monovalent ion size on colloidal forces probed by Monte Carlo simulations

The present work studies the role of ionic size in the interactions between the electrical double layers of colloids immersed into electrolyte solutions of monovalent ions. Such interactions are studied by means of Monte Carlo (MC) simulations and the classical Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. Despite the omission of the steric effects and some other features of real electrolyte solutions, DLVO theory is known to work qualitatively well for 1:1 electrolyte solutions. However, this affirmation is based on previous tests where an ionic diameter around 0.4 nm was taken for all ionic species. In contrast, some experimental studies suggest that larger hydrated ions should be considered and even specified for each type of ion. In this work, the importance of ionic size is analyzed by applying the primitive model of electrolyte to the intermediate region between a pair of equally charged infinite planar surfaces. The double layer interactions were calculated from the ionic densities at the distance of closest approach to the charged surfaces, this method constitutes an alternative to the traditional calculations at the midplane. Our MC simulations predict the existence of negative net pressures for monovalent electrolytes in the case of zero charge density. In addition, MC simulations reveal some disagreements with theoretical predictions for ionic diameters larger than 0.4 nm. These discrepancies can become significant if surface charge density is large enough due to the restructuration of the double layer. The physical mechanisms for these deviations are also discussed.