Fast GC with a Small Volume Column Oven and Low Power Heater

A new apparatus for fast gas chromatography separations is described. It consists of a small volume oven containing a coiled fused silica capillary column that is heated by a flow of hot air. The oven can be heated at rates of 10 °C s^?1 with a 300 W heater. Benchmark studies at various temperature programming rates are described. Retention time relative standard deviations increase with increasing heating rate, but are at most about 1% when an 8 °C s^?1 heating rate is employed. The small size of the column oven makes it possible for it to be attached to a commercial GC instrument through an opening provided for installation of a second injector.     

Volcanic Rock Materials for Defluoridation of Water in Fixed-Bed Column Systems

Consumption of drinking water with a high concentration of fluoride (>1.5 mg/L) causes detrimental health problems and is a challenging issue in various regions around the globe. In this study, a continuous fixed-bed column adsorption system was employed for defluoridation of water using volcanic rocks, virgin pumice (VPum) and virgin scoria (VSco), as adsorbents. The XRD, SEM, FTIR, BET, XRF, ICP-OES, and pH Point of Zero Charges (pH_PZC) analysis were performed for both adsorbents to elucidate the adsorption mechanisms and the suitability for fluoride removal. The effects of particle size of adsorbents, solution pH, and flow rate on the adsorption performance of the column were assessed at room temperature, constant initial concentration, and bed depth. The maximum removal capacity of 110 mg/kg for VPum and 22 mg/kg for VSco were achieved at particle sizes of 0.075–0.425 mm and <0.075 mm, respectively, at a low solution pH (2.00) and flow rate (1.25 mL/min). The fluoride breakthrough occurred late and the treated water volume was higher at a low pH and flow rate for both adsorbents. The Thomas and Adams–Bohart models were utilized and fitted well with the experimental kinetic data and the entire breakthrough curves for both adsorbents. Overall, the results revealed that the developed column is effective in handling water containing excess fluoride. Additional testing of the adsorbents including regeneration options is, however, required to confirm that the defluoridation of groundwater employing volcanic rocks is a safe and sustainable method.     

Rapid Analysis of Nitrate and Nitrite by Ion-Interaction Chromatography on a Monolithic Column

Ion-interaction chromatography with direct conductivity detection has been used for analysis of nitrate and nitrite. Chromatographic separation was performed on a monolithic silica-based C₁₈ column dynamically modified with tetrabutylammonium (TBA⁺). Using the optimized mobile phase, containing 2.0 mmol L^?1 TBA⁺ and 0.8 mmol L^?1 citrate (pH 6.0), delivered at a flow rate of 6.0 mL min^?1, separation of five anions (chloride, nitrite, bromide, nitrate, and sulfate) was achieved in only 40 s at a column temperature of 30 °C. The detection limits for nitrate and nitrite were 0.74 and 0.92 mg L^?1, respectively. The relative standard deviation (RSD, n = 5) of the retention times of nitrate and nitrite was 0.1% and RSD of chromatographic peak areas were 0.4 and 0.2%, respectively. The method was successfully used for analysis of the anions in groundwater. Recovery of nitrate and nitrite was 99.1 and 105%, respectively.     

Histidine as the functional group for a chelating ion exchanger

In the chelating ion exchanger synthesized, the amino group of histidine is attached chemically via the azide method to the carboxyl group of Amberlite IRC-50. A flow system based on a spectrophotometric detector, with 4-(2-pyridylazo) resorcinol as reagent, is described for fast assays of eluted cations. The pH dependence of the metal extraction is reported for Ag(I), Au(III), Cu(II), Fe(III), Hg(II), Ni(II) and Zn(II) ions. The resin exhibits no affinity for the alkali or alkaline earth metals. The uptake of traces of the specified elements from synthetic samples by a short (90 mm) column of the histidine-containing resin was in the range 94–100% and the retained metals were readily eluted by means of 2 M hydrochloric or hydrobromic acid. In column operation, mercury was quantitatively recovered even in the presence of large excesses of various ligands. The recoveries of the trace metals were good at the usual pH of natural waters.     

Separation and determination of traces of heavy metals complexed with humic substances in river waters by sorption on indium-treated amberlite xad-2 resin

A nonionic macroreticular styrene/divnylbenzene copolymer, Amberlite XAD-2 resin is pulverized to 1–10 μm and treated with indium ions to saturate traced of cation exchange sites for the quantitative separation of humic complexes from cations. A 100-ml filtered sample is passed through an indium-treated XAD-2 column (16 diameter, 5 mm tall) at pH 5 at a flow rate of 2 ml min^? to sorb heavy metals complexed with humic and fulvic acids. Inorganic cations and anions, EDTA complexes and colloidal hydrated iron(III) oxide are not retained on the column at all. The heavy metals sorbed on the column are then ultrasonically desorbed with 0.5 M nitric acid and determined by graphite-furnace atomic absorption spectrometry. The results fo two river water samples obtained are in good agreement with those obtained when the macroreticular weak-base anion-exchanger DEAE-Sephadex A-25 is used.     

Preconcentration of Zr, Hf, Nb, Ta and W in seawater using solid-phase extraction on TSK-8-hydroxyquinoline resin and determination by inductively coupled plasma-mass spectrometry

Here, we present the first simultaneous preconcentration and determination of ultratrace (pmol kg⁻¹ level) Zr, Hf, Nb, Ta and W in seawater, both in the form of dissolved and acid-dissolvable species. 8-Hydroxyquinoline (8HQ) bonded covalently to a vinyl polymer resin, TSK-8HQ, was used in a chelating adsorbent column to concentrate the metals. The greatest advantage of this resin is its endurance to 5 M HF, since this is an effective eluent for all five metals. The analytes were successfully concentrated from 250 mL seawater with a 50-fold concentration factor through the column extraction and evaporation. The detection limit was 0.009-0.15 pmol kg⁻¹. The procedure blank determined using ultra pure water as a sample was 0.005-0.37 pmol kg⁻¹. The five metals were quantitatively recovered from seawater with good precision (2-4%). The effect of sample pH, sample flow rate, eluent composition and sample pretreatment were carefully studied. This method was applied to seawater.     

胺型键合固定相分离碱性物质的影响因素考察

 以某些碱性物质为探测溶质 ,中性物质乙苯为参照溶质 ,详尽考察了检测温度、缓冲液中阳离子浓度、流动相的流速分别在流动相的 pH值为 3 0和 7 0时对胺型键合固定相分离碱性物质的影响。研究结果表明 ,随着温度的升高 ,碱性物质的保留时间先下降较快 ,然后趋于平缓 ,而柱效和峰形分别得到了提高和改善 ;缓冲液中阳离子浓度对碱性物质的保留行为有较大的影响 ;碱性物质的最佳流速较中性物质小。由于胺型键合固定相中的疏水烷基链中引入了极性官能团氨基 ,因此碱性物质在该固定相上的行为比在传统的固定相上更为复杂。     

Column Chromatographic Preconcentration of Copper in Alloys and Complex Materials Using 9,10 Phenanthrenequinone Monoxime Supported on Naphthalene

Abstract

A solid chelating compound phenanthrenequinone monoxime PQM) supported on naphthalene provides a rapid and economical means of preconcentration and separation of copper from the aqueous samples. Copper forms a complex with PC:: supported on naphthalene in the column at pH 6.1–8.4 with a flow rate of 1 ml/min. The metal complex and naphthalene are dissolved out from the column with 5 ml of DMF and the absorbance is measured at 470 nm against reacent blank. Beer's law is obeyed in the concentration range 0.6 9.6 μg of copper in 5 ml of DMF. The molar absorptivity and sensitivity are 6.3×10⁴ L mol^?1 cm^?1 and 0.001 μg cm^?2 respectively.     

Purification of IgG from Sera of Rabbit and Guinea Pig by Flow-Through Mode Ion-Exchange Chromatography using DEAE Sepharose Fast Flow Column

A one-step purification process using flow-through mode ion-exchange chromatography (Ft-IEC) was evaluated for the purification of Immunoglobulin G (IgG) from rabbit and guinea pig serum. A simple protein precipitation with saturated ammonium sulfate was used to pretreated plasma samples. Chromatographic separation was carried out on DEAE Sepharose Fast Flow (F.F.) column at a flow rate of 1 mL min^?1. Ft-IEC using Tris?CHCl buffer at pH 7.0 allowed the recovery of 22% of the loaded IgG with purity of 95% existed in flowthrough and washing effluents but not in elution effluents. To be compared, bind-elute mode IEC using Tris?CHCl buffer at pH 8.5 based on the routine protocol showed that the recovery of 15% of the loaded IgG with purity of 80% existed in elution effluents. These results indicate that the Ft-IEC is an effective method for purifying IgG from sera of rabbit and guinea pig and may also be suitable for other animal sera by adjusting pH at equilibrium buffer for chromatography column.     

C18柱串联冠醚手性柱高效分离3种芳香族氨基酸对映体

将C18柱与手性冠醚柱串联,建立了一种反相高效液相色谱法用于3种芳香族氨基酸对映体同时拆分的方法.考察了反相色谱流动相的组成、pH值、柱温、流速对对映体拆分的影响.实验结果表明,当流动相为HClO4-乙睛溶液(86:14,V/V,pH 2.0)、柱温20℃、流速0.4 mL/min时,3种氨基酸对映体可获得基线分离.进一步对比了C18柱、冠醚手性柱和串联顺序不同的4种分离模式,结果表明,C18柱不能拆分氨基酸对映体,仅能分离不同种类氨基酸;冠醚手性柱可分离氨基酸映体,但不同种类氨基酸色谱峰出现重叠;串联模式能实现3种氨基酸对映体的基线分离,实现双柱优势互补,而串联顺序对分离影响不大,仅影响色谱峰的峰形.     

Preconcentration and Determination of Toxic Metals by A New Calix[4]arene Bonded HPLC Column

The present study deals with the preconcentration and determination of toxic metal ions using p-tetranitrocalix[4]arene (3) appended silica-based new HPLC column. The synthesized material was characterized using Fourier transform infrared and scanning electron microscopy techniques. The sorption characteristics of the HPLC column were investigated for three toxic metals (Cd²⁺, Hg²⁺ and Pb²⁺) in column agreement. The experiments were performed in five steps that were monitored using a UV–visible diode-array detector. However, all the HPLC experimental results were reconfirmed by using atomic absorption spectrophotometer. The effect of concentration on the sorption efficiency of the column was evaluated for all the three metals and the data obtained were investigated using Langmuir, Freundlich and Dubinin–Redushkevich (D–R) sorption isotherms. The value of coefficient of determination (R ²), i.e. 0.99, suggested that the Freundlich sorption isotherm was found to be the best-fit model for all the three toxic metal ions, whereas, mean free energy was calculated from the D–R isotherm as 5.3, 5.7, and 5.8 kJ/mol for Pb²⁺, Cd²⁺, and Hg²⁺, respectively; suggesting that physical electrostatic force is involved in the sorption process. The developed method was validated for system efficiency, accuracy, and precision.     

Adsorption Strategy of Plasmid DNA Nanoparticulate: Preparative Purification by a Simple Custom Expanded Bed Column

This paper summarizes the critical examination of the hydrodynamic performance of the NBG expanded bed contactor operated with streamline-DEAE adsorbent under various operating conditions for expanded bed adsorption of plasmid DNA nanoparticles from alkaline lysate. The purification process is not RNase-free. In this study, a rapid and efficient scaleable purification protocol obtaining, plasmid DNA nanoparticles (average size of 40 nm) with a high purity level for use as therapeutic agent in customized NBG expanded bed columns was developed. This technique allows efficient levels of binding to the column media and vector purification without centrifugation or filtration steps. Residence time distribution (RTD) studies were exploited to achieve the optimal condition of plasmid DNA nanoparticle (pDNA) recovery upon anion exchange adsorbent in this contactor. In addition, the purification experiments were carried out in the expanded bed columns with settle bed height of 6.0 ± 0.2 cm. NaCl gradient elution enabled the isolation of supercoiled plasmid from low-Mr RNA, cDNA and plasmid variants. Subsequently dynamic binding capacity of the adsorbent was calculated while these values decreased with increase in flow velocity. Moreover, the effect of pH upon the performance of this recovery process and the feedstock volume upon the expanded bed anion exchange purification was investigated. The results demonstrated that separation of low-Mr RNA from plasmid DNA isoforms in the range of pH between 5.5 and 7.5 is achievable in this column. The yield of recovery of pDNA in optimal condition was higher than 88.51% which was a superior result in one-pass frontal chromatography. The generic application of simple customized NBG expanded bed column and its potential for the purification and recovery of plasmid DNA as a nanoparticulate bioproduct is strongly discussed.     

Preconcentration and Determination of Toxic Metals by A New Calix[4]arene Bonded HPLC Column

The present study deals with the preconcentration and determination of toxic metal ions using p-tetranitrocalix[4]arene (3) appended silica-based new HPLC column. The synthesized material was characterized using Fourier transform infrared and scanning electron microscopy techniques. The sorption characteristics of the HPLC column were investigated for three toxic metals (Cd²⁺, Hg²⁺ and Pb²⁺) in column agreement. The experiments were performed in five steps that were monitored using a UV–visible diode-array detector. However, all the HPLC experimental results were reconfirmed by using atomic absorption spectrophotometer. The effect of concentration on the sorption efficiency of the column was evaluated for all the three metals and the data obtained were investigated using Langmuir, Freundlich and Dubinin–Redushkevich (D–R) sorption isotherms. The value of coefficient of determination (R ²), i.e. 0.99, suggested that the Freundlich sorption isotherm was found to be the best-fit model for all the three toxic metal ions, whereas, mean free energy was calculated from the D–R isotherm as 5.3, 5.7, and 5.8 kJ/mol for Pb²⁺, Cd²⁺, and Hg²⁺, respectively; suggesting that physical electrostatic force is involved in the sorption process. The developed method was validated for system efficiency, accuracy, and precision.

     

Adsorption behaviour of cadmium on L-methionine immobilized on controlled pore glass

The adsorption behaviour of Cd onto the relative non-polar L-methionine was studied. To this end, L-met was immobilized on controlled pore glass (CPG), incorporated in a microcolumn and inserted in a flow injection system for Cd preconcentration from aqueous solutions. Binding constant of the system was calculated and it turned to be of 1.99, with sites capacity of n = 3.12. The ratio of Cd moles bound to L-met moles was calculated and it was 0.03:1 at pH 9.0. On-line breakthrough curves were used to study the effect of pH, analyte concentration and influent flow rate on Cd retention. A complementary pH study was added with a titration curve. Transient peak areas revealed that Cd stripping from the column occurred instantaneously. The system achieves an enrichment factor of 130, reaching a detection limit of 0.63 ng L^{− 1} when 10 mL of the solution were passed through the column. The method was successfully applied to Cd determination in the standard reference material (SRM), QC METAL LL2 metals in natural water, as a validation study.     

Characterization and separation of Al13 species using gel-filtration chromatography

A polyaluminum chloride (PAC) sample was prepared using a slow alkaline titration method. The Bio-Gel P-100 gel column chromatographic technique was used to separate and characterize the various forms of aluminum present in the prepared PAC solution. The effluents from a gel column were monitored using online chemical method: Al-Ferron timed complexation spectrophotometry and by ²⁷Al nuclear magnetic resonance (NMR) spectroscopy. Effects of different experimental conditions such as eluent flow rate, ionic strength and pH on separation of Al₁₃ were investigated. Experimental results indicated that molecule size exclusion was not the only parameter affecting the column chromatographic separation efficiency of Al₁₃ but molecule charge as well. Reducing the eluent flow rate, increasing the ionic strength and suitable pH resulted in increase in the separation efficiency. Experimental results clearly indicated that by varying the experimental conditions, it is possible to produce pure Al₁₃ species using a gel column chromatographic technique.     

Characterization and separation of Al13 species using gel-filtration chromatography

A polyaluminum chloride (PAC) sample was prepared using a slow alkaline titration method. The Bio-Gel P-100 gel column chromatographic technique was used to separate and characterize the various forms of aluminum present in the prepared PAC solution. The effluents from a gel column were monitored using online chemical method: Al-Ferron timed complexation spectrophotometry and by ²⁷Al nuclear magnetic resonance (NMR) spectroscopy. Effects of different experimental conditions such as eluent flow rate, ionic strength and pH on separation of Al₁₃ were investigated. Experimental results indicated that molecule size exclusion was not the only parameter affecting the column chromatographic separation efficiency of Al₁₃ but molecule charge as well. Reducing the eluent flow rate, increasing the ionic strength and suitable pH resulted in increase in the separation efficiency. Experimental results clearly indicated that by varying the experimental conditions, it is possible to produce pure Al₁₃ species using a gel column chromatographic technique.     

Preconcentration of Trace Cadmium (II) and Copper (II) in Environmental Water Using a Column Packed with Modified Silica Gel-Chitosan Prior to Flame Atomic Absorption Spectrometry Determination

A new column loaded with modified silica gel-chitosan is proposed as a preconcentration system for adsorption of trace cadmium (II) and copper (II). The optimization steps were performed under dynamic conditions, involving pH, sample flow rate, eluent selection, concentration, volume, and flow rate. Trace Cd(II) and Cu(II) were quantitatively adsorbed by the modified silica gel-chitosan. The metal ions adsorbed on the separation column were eluted with 0.1 M HNO₃ and determined by flame atomic absorption spectrometry. Under the optimum conditions, this method allowed the determination of cadmium and copper with limits of detection (LOD) of 20 ng L^?1 and 38 ng L^?1, respectively. The relative standard deviation values (RSDs) for 1.0 mg L^?1 of cadmium and 1.0 mg L^?1 of copper were 2.62% and 2.85%, respectively.     

The lon-chromatographic behavior of arsenite,arsenate, methylarsonic acid and dimethylarsinic acid on the hamilton PRP-X100 anion-exchange column

The HPLC separation of arsenite, arsenate, methylarsonic acid and dimethylarsinic acid has been studied in the past but not in a systematic manner. The dependence of the retention times of these arsenic compounds on the pH of the mobile phase, on the concentration and the chemical composition of buffer solutions (phosphate, acetate, potassium hydrogen phthalate) and on the presence of sodium sulfate or nickel sulfate in the mobile phase was investigated using a Hamilton PRP-X100 anion-exchange column. With a flame atomic absorption detector and arsenic concentrations of at least 10 mg dm^?3 all investigated mobile phases will separate the four arsenic compounds at appropriate pH values in the range 4–8. The shortest analysis time (?3 min) was achieved with a 0.006 mol dm^?3 potassium hydrogen phthalate mobile phase at pH 4, the longest (?10 min) with 0.006 mol dm^?3 sodium sulfate at pH 5.9 at a flow rate of 1.5 cm³ min^?1. With a graphite furnace atomic absorption detector at the required, much lower, flow rate of ?0.2 cm³ min^?1 acceptable separations were achievable only with the pH 6 phosphate buffer (0.03 mol dm^?3) and the nickel sulfate solution (0.005 mol dm^?3) as the mobile phase. To become detectable approximately 100 ng arsenic from each arsenic compound (100 μl injection) must be chromatographed with the phosphate buffer, and approximately 10 ng with the nickel sulfate solution.     

Behaviour of Salbutamol on Diol Normal-Phase Column

Summary The behaviour of salbutamol, a sympathomimetic amine-and catecholamine-like substance, was studied on Diol normal-phase column. The possibility for controlled retention of salbutamol using methanol containing mobile phase was proved. The mobile phase consisted of buffer (0.05 M H₃PO₄, pH 5.0 with TEA) – methanol (15:85 v/v). The effects of organic solvent, pH, ion power of the buffer and the length of amine alkyl chain in buffer were studied. The retention of salbutamol increased significantly with the increase of methanol content above 80%. At pH values between 3.5 and 7.5 the retention of salbutamol varied from 2.16 to 2.36 only. The limit of quantitation was 0.30 ng · mL^–1. The investigations confirm the H-bonding retention mechanism.     

High Performance Liquid Chromatographic Analysis of Desipramine in Human Plasma Using a Microbore Column Technique

Abstract

A reversed-phase, isocratic HPLC method has been developed for the quantitation of desipramine in human plasma. the method involved the use of cloimpramine as an internal standard. the chromatographic separation was accomplished with a mobile phase comprising acetonitrile-aqueous solution (60:40. v/v) containing 10 mM disodium hydrogenphosphate and 80 mM sodium dodecyl sulfate adjusted to pH 2. the mobile phase was pumped at a flow rate of 0.5 ml/min. the column used was a microbore column (2 mm I.D. × 100 mm) packed with a C18 reversed-phase material (5μm ODS Hypersil). Plasma samples were extracted at basic pH with diethyl ether followed by back-extraction into 0.1 N sulfuric acid. Using UV detection at 250 nm, the lower limit of sensitivity was 10 ng/ml. the inter- and intra-assay coefficients of variation were found to be less than 10%. the assay procedure was applied to a long term oral dosing study in patients to monitor the plasma concentration of desipramine.