Highly sensitive and selective solid-contact calcium sensor based on Schiff base of benzil with 3-aminosalycilic acid covalently attached to polyacrylic acid amide for health care

Solid-state potentiometric calcium sensors based on newly synthesized Schiff’s base of 3-aminosalycilic acid with benzil [2-hydroxy-3-(2-oxo-1,2-diphenylethylidene)amino) benzoic acid] ionophore I and with isatin [2-hydroxy-3-(2-oxoindolin-3-ylidene amino)benzoic acid] ionophore II ionophores and their covalently attached to polyacrylamide ionophores III and IV, respectively, were developed. The all-solid-state sensors were constructed by the application of a thin film of polymeric membrane cocktail onto gold electrodes that were pre-coated with the conducting polymer poly (3,4-ethylenedioxy-thiophen) as an ion and electron transducer. More than 40 sensors with membranes containing plasticized PVC or poly(butyl methacrylate-co-dodecyl methacrylate as a plasticizer-free membrane matrix were investigated. The constructed sensors contained various amounts of the different ionophores with and without anionic lipophilic additive. The sensor containing 10% of ionophore III and 3% tetra (p-chlorophenyl) borate in acrylate copolymer exhibited a stable potentiometric response over a wide pH range of 4–9. It possessed a linear concentration range of 6 10^?10 to 1 10^?2 mol L^?1 with a Nernstian slope of 28.5 mV/decade and a limit of detection (LOD) of 2 10^?10 mol L^?1. It exhibited a good selectivity for calcium to other cations. The selectivity coefficients towards different mono-, di- and trivalent cations were determined with the fixed interference method (FIM) and separate solution method (SSM). The sensor’s life time is more than 3 months, without significant deterioration in the slope. The proposed sensors were utilized for the determination of calcium concentration in serum. The results were compared with those obtained from routine clinical laboratory electrolyte analyser. The results reveal that the all-solid-state calcium sensor is promising for the point of care testing.     

Amide and Acyl‐Hydrazine Functionalized Calix[4]arenes as Carriers for Hydrogen Phosphate Selective Electrodes

Anion‐selective solvent polymeric membrane based on hydrogen bond‐forming, neutral ionophores with amide or acyl‐hydrazine groups are described. The use of the two calix[4]arenes results in anion‐selective electrodes with a selectivity for phosphate. The electrodes of the optimum characteristic have the composition of 1 wt% ionophore, 66 wt% o‐NPOE, 33 wt% poly (vinyl chloride) (PVC) and TDMACl (15 or 30 mol% relative to the ionophore 1 and 2 , respectively). The optimized membrane electrodes show Nernstian responses towards monohydrogen phosphate (?29.1 and ?29.3 mV/decade) based on ionophore 1 and 2 , respectively, in a wide concentration range (1.0×10^?5 to 1.0×10^?2 or 1.0×10^?5 to 1.0×10^?1 M). The selectivity coefficients are determined with the fixed interference method and the activity ratio method. The electrodes display an anti‐Hofmeister series selectivity pattern and highly selective for HPO₄^2? over Cl^?, Br^?, CH₃COO^?, NO₃^? and SO₄^2?. The lifetime of the electrodes is at least 1 month and their response time is found to be 25 s. The proposed sensors could be put to analytical use both by direct potentiometry as well as potentiometric titration.     

Solid‐contact Acetate‐selective Electrode Based on a 1,3‐bis(carbazolyl)urea‐ionophore

The construction and study of solid‐contact acetate‐selective electrodes is described using a 1,3‐bis(carbazolyl)urea derivative as a neutral hydrogen‐bonding ionophore and poly(3,4‐ethylenedioxythiophene) as the solid contact. It was shown recently that this ionophore binds acetate (logK_ass=4.98) that is used as primary ion in this study. The electrodes show linearity over the activity range of 10^?4.50–10^?1.10 with a sub‐Nernstian slope of ?51.3 mV per decade and a detection limit of 10^?5.00. The anion‐selectivity pattern of these electrodes deviates markedly from the Hofmeister pattern. When adding ionophore to the membrane the logarithm of the selectivity coefficient (logK) for SCN^? decreased from 6.5 to 1.2, logK for I^? decreased from 5.7 to 0.9, logK for NO₃^? decreased from 4.3 to 0.6 and logK for Br^? decreased from 3.3 to 0.1. The selectivity coefficients of hydrophilic anions such as Cl^?, F^?, HPO₄^2?, and SO₄^2? are significantly lower than in case of the ionophore‐free membrane. It was discovered that the constructed electrodes are also relatively selective to bicarbonate. This work is an important step towards the further development of solid‐contact anion‐selective electrodes.     

Comparative study of carbon paste electrodes modified by new pentaaza macrocyclic ligands and gold nanoparticles embedded in three-dimensional sol–gel network for determination of trace amounts of Ag(I)

Two new Ag(I) chemically modified carbon paste electrodes were prepared with comparative potentiometric study of 1,3,6,10,13-pentaaza-2,14-(2,6-pyridyl)-cyclotetradecane-4,12-dione (PPCT) and 1,3,6,9,11,12-pentaaza-2,13-(2,6-pyridyle)-bicycle[2,2,9]pentadecane-4,11-dione (PPBP) as ionophore. These sensors have been modified with sol–gel–Au nanoparticles to obtain a wide concentration range for potentiometric determination of Ag(I) in aqueous solutions. The sensors exhibit significantly enhanced selectivity toward Ag(I) ions over a wide concentration range of 4.0 × 10^?9–2.2 × 10^?2 and 2.2 × 10^?7–2.0 × 10^?2 mol L^?1 with a lower detection limit of 2.5 × 10^?9 and 2.0 × 10^?7 mol L^?1 for PPCT and PPBP modified electrodes respectively. The electrodes are highly selective to Ag(I) ions over a large number of mono, bi, and tri-valent cations. These electrodes were successfully used as indicator electrode for potentiometric determination of silver in sulphadiazine (burning cream) and radiological film.     

Tetracycline Potentiometric Sensor Based on Cyclodextrin for Pharmaceuticals and Waste Water Analysis

In this work, the construction and performance evaluation of PVC membranes ion‐selective electrodes for the determination of tetracycline type antibiotics is described. Electrodes with the best responses were based on plastic membranes containing 31% (w/w) PVC, 68% (w/w) of dibutylphthalate as plasticizer and 1% (w/w) of β‐cyclodextrin as ionophore. The electrodes were responsive over 6 months to tetracycline, oxytetracycline, doxycycline and chlortetracycline in glycine buffer solution (pH 2), in the dynamic range 2×10^?5–10^?2 mol L^?1 with a constant slope of about 55 mV/dec To enable large scale analysis reducing wastes as associated costs tubular shape electrodes were coupled to a sequential‐injection analysis system and its performance evaluated using pharmaceutical samples and waste waters from a treatment facility. The sample throughput of 51 samples h^?1 was enabled by the system as well as results that favorably agree with those provided by chromatographic analysis.     

Modified Screen-Printed Electrode for Potentiometric Determination of Copper(II) in Water Samples

Modified screen printed (SPE) and carbon paste electrodes (CPE) with phenanthroline–tetraphenyl borate ionophore [Phen:TPB] were fabricated for the determination of copper(II). The modified electrodes have linear responses over a wide concentration range (1 × 10^?6–1 × 10^?2 mol·L^?1) of copper(II) ion at 25 °C with divalent cationic slopes of 29.85 ± 0.58 and 29.45 ± 0.81 mV·decade^?1 and exhibit a detection limit of 1 × 10^?6 mol·L^?1 for SPE and CPE. The selectivity coefficient was measured using the match potential method in acetate buffer of pH = 4.2. The modified SPE and CPE sensors show high selectivity and sensitivity for determination of copper(II) and also show stable and reproducible response over a period of five and three months for SPE and CPE sensors, respectively. This method can be used for determination of copper(II) in water, soil, plant and fish tissue samples and the results obtained agreed with those obtained with atomic absorption spectrometer (AAS).     

Mercury ion selective poly(aniline) solid contact electrode based on 2-mercaptobenzimidazol ionophore

A mercury(II) ion selective poly(aniline) solid contact electrode based on 2-mercaptobenzimidazol (2MBI) ionophore as a sulfur containing sensing material was successfully developed. The electrode exhibits a good linear response of 29.1 mV/decade (at 20 ± 0.2°C, r ² = 0.997) within the concentration range of 1 × 10^?2?1 × 10^?7 M Hg(II). The composition of this electrode was: ionophore 0.100, polyvinylchloride (PVC) 0.330, dibutylphthalate (DBP) 0.470, potassiumtetrakis(4-chlorophenyl)borate (KTpCIPB) 0.090, and oleic acid (OA) 0.010. A poly(aniline) solid contact electrode based on 2MBI with DBP and OA plasticizers exhibited the best response characteristics of the results obtained for similarly coated wire type electrodes and solid contact electrodes based on only one DBP plasticizer. The electrode shows good selectivity for mercury(II) ions in comparison with alkali, alkaline earth, transition and heavy metal ions. This electrode is suitable for use with aqueous solutions of pH 3.3?C8.0 and the standard deviation in the measured EMF difference was ±0.5 mV in a mercury nitrate sample solution of 1.0 × 10^?2 M and ±1.1 mV in a mercury nitrate sample solution of 1.0 × 10^?3 M. The stabilization time was less than 15 min and the response time was less than 33 s. The electrode was applied as a sensor for the determination of Hg(II) content in a sea water sample and some amalgam alloys. The results show good correlation with data obtained by atomic absorption spectrometry.     

Processing of signals from an ion-elective electrode array by a neural network

Neural network software is described for processing the signals of arrays of ion-selective electrodes. The performance of the software was tested in the simultaneous determination of calcium and copper(II) ions in binary mixtures of copper(II) nitrate and calcium chloride and the simultaneous determination of potassium, calcium, nitrate and chloride in mixtures of potassium and calcium chlorides and ammonium nitrate. The measurements for the Ca²⁺/Cu²⁺ determinations were done with a pH-glass electrode and calcium and copper ion-selective electrodes; results were accurate to ±8%. For the K⁺/Ca²⁺NO^?₃/Cl^? determinations, the measurements were made with the relevant ion-selective electrodes and a glass electrode; the mean relative error was ±6%, and for the worst cases the error did not exceed 20%.     

PVC‐Based on Thiopyrilium Derivatives Membrane Electrodes for Determination of Histamine

This study describes novel histamine‐selective electrodes, having their basis on thiopyrilium (TP) derivatives as suitable ionophores. The electrodes were prepared by incorporating the TP derivatives into plasticized poly(vinyl chloride) (PVC) membranes. These electrodes demonstrate high selectivity as far as the histamine response is considered, as compared with many common inorganic anions and other kinds of amino acids. The influence of membrane composition, pH and the effect of lipophilic cationic and anionic additives on the response characteristics of the electrode were investigated. The resulting sensor based on 2,6‐bis(4‐dimethyl amino phenyl)‐4‐phenyl thiopyrilium perchlorate (TP4) responds to histamine in a wide concentration range from 5.0 × 10^?6 to 1.0 × 10^?1 M with a slope of 54.8 ± 0.6 mV decade^?1 and detection limit of 3.0 μ mol L^?1 (～0.3 ppm). The electrode illustrates fast response time and good long‐term stability (more than 2 months). The ability to design histamine‐selective electrodes based on new thiopyrilium derivatives and both to alter selectivity and improve the response characteristics through structural changes to the charged ionophore, has been investigated. The prepared electrode was used for the determination of histamine in a synthetic human serum sample. Consequently, satisfactory recovery results were obtained over a wide concentration range of histamine.     

Electrochemical Investigations of the Anticancer Drug Idarubicin Using Multiwalled Carbon Nanotubes Modified Glassy Carbon and Pyrolytic Graphite Electrodes

The effect of surface modifications on the electrochemical behavior of the anticancer drug idarubicin was studied at multiwalled carbon nanotubes modified glassy carbon and edge plane pyrolytic graphite electrodes. The surface morphology of the modified electrodes was characterized by scanning electron microscopy. The modified electrodes were constructed for the determination of idarubicin using adsorptive stripping differential pulse voltammetry. The experimental parameters such as supporting electrolyte, pH, accumulation time and potential, amount of carbon nanotubes for the sensitive assay of idarubicin were studied as details. Under the optimized conditions, idarubicin gave a linear response in the range 9.36×10^?8–1.87×10^?6 M for modified glassy carbon and 9.36×10^?8–9.36×10^?7 M for modified edge plane pyrolytic graphite electrodes. The detection limits were found as 1.87×10^?8 M and 3.75×10^?8 M based on modified glassy carbon and edge plane pyrolytic graphite electrodes, respectively. Interfering species such as ascorbic acid, dopamine, and aspirin showed no interference with the selective determination of idarubicin. The analyzing method was fully validated and successfully applied for the determination of idarubicin in its pharmaceutical dosage form. The possible oxidation mechanism of idarubicin was also discussed. The results revealed that the modified electrodes showed an obvious electrocatalytic activity toward the oxidation of idarubicin by a remarkable enhancement in the current response compared with bare electrodes.     

Solid contact PVC membrane electrodes based on neutral or charged carriers for the selective reading of anionic sulfamethoxazole and their application to the analysis of aquaculture water

Sulfamethoxazole (SMX) is among the antibiotics employed in aquaculture for prophylactic and therapeutic reasons. Environmental and food spread may be prevented by controlling its levels in several stages of fish farming. The present work proposes for this purpose new SMX selective electrodes for the potentiometric determination of this sulphonamide in water. The selective membranes were made of polyvinyl chloride (PVC) with tetraphenylporphyrin manganese (III) chloride or cyclodextrin-based acting as ionophores. 2-nitrophenyl octyl ether was employed as plasticizer and tetraoctylammonium, dimethyldioctadecylammonium bromide or potassium tetrakis (4-chlorophenyl) borate was used as anionic or cationic additive. The best analytical performance was reported for ISEs of tetraphenylporphyrin manganese (III) chloride with 50% mol of potassium tetrakis (4-chlorophenyl) borate compared to ionophore. Nersntian behaviour was observed from 4.0?×?10^?5 to 1.0?×?10^?2?mol/L (10.0 to 2500?µg/mL), and the limit of detection was 1.2?×?10^?5?mol/L (3.0?µg/mL). In general, the electrodes displayed steady potentials in the pH range of 6 to 9. Emf equilibrium was reached before 15?s in all concentration levels. The electrodes revealed good discriminating ability in environmental samples. The analytical application to contaminated waters showed recoveries from 96 to 106%.     

1‐Pyrrolidine Dicarbodithioate Based Electrodes for Determination of Iron(III) in Lubrication Oil

The lipophillic ammonium salt of 1‐pyrrolidine dicarbodithioic acid (PCDT) (I) was introduced as a new selective ionophore for an iron selective electrode. In addition, the effect of immobilization of 18‐crown‐6 (18CE6) (membrane type‐II), on the electrode performance was discussed. The slope of the PCDT‐based (I) electrode was (20 mV/decade). The linear concentration range was (10^?5–10^?1 M) after one day doping. The detection limit for electrode type‐(II) was (1.3×10^?6 M). For membrane with only 18CE6 (type‐III) the linear range and the detection limit were improved (10^?5–10^?1 M and 3.2×10^?6 M, respectively). The pH‐range was between 5–11 for type‐II, and III electrodes, while it was 7–11 for type‐I electrode. Most of the common cations were tested for the evaluation of the electrode selectivity with correlation to the ionic radii of the tested cations. Among them only Ag⁺ and Pb²⁺ were the real interference for type‐III electrode. Application of using the electrode for the determination of iron in lubrication oil samples was performed with RSD (1.77–2.7%) and (1.01–2.3%) for type‐II and III electrodes, respectively. The corresponding recovery ranges were (93.0–99.9%) and (96.3–100%). The obtained results were compared to those of an atomic absorption spectrophotometric method.     

Construction and Performance Characterization of Ion‐Selective Electrodes for Potentiometric Determination of Paroxetine Hydrochloride in Pharmaceutical Preparations and Biological Fluids

Three types of ion‐selective electrodes: PVC membrane, modified carbon paste (CPE), and coated graphite electrodes (CGE) have been constructed for determining paroxetine hydrochloride (Prx). The electrodes are based on the ion pair of paroxetine with sodium tetraphenylborate (NaTPB) using dibutyl phthalate as plasticizing solvent. Fast, stable and potentiometric response was obtained over the concentration range of 1.1×10^?5–1×10^?2 mol L^?1 with low detection limit of 6.9×10^?6 mol L^?1 and slope of a 56.7±0.3mV decade^?1 for PVC membrane electrode, the concentration range of 2×10^?5–1×10^?2 mol L^?1 with low detection limit of 1.2×10^?5 mol L^?1 and slope of a 57.7±0.6 mV decade^?1 for CPE, and the concentration range of 2×10^?5–1×10^?2 mol L^?1 with low detection limit of 8.9×10^?6 mol L^?1 and slope of a 56.1±0.1 mV decade^?1 for CGE. The proposed electrodes display good selectivity for paroxetine with respect to a number of common inorganic and organic species. The electrodes were successfully applied to the potentiometric determination of paroxetine hydrochloride in its pure state, its pharmaceutical preparation, human urine and plasma.     

Nitrite‐Selective Electrode Based On Cobalt(II) tert‐Butyl‐Salophen Ionophore

A series of polymeric nitrite‐selective electrodes containing a new lipophilic ionophore Co(II) tert‐butyl‐salophen is reported. The stability of Co(II) ionophores within a PVC‐based membrane was investigated by leaching experiments. Different membrane compositions were explored in order to reach the lowest possible limit of detection for a PVC‐based nitrite selective polymeric membrane electrode containing this ionophore. The optimal electrode showed a limit of detection of 2×10^?6 M and exhibited four orders of magnitude of discrimination over nitrate, chloride and bromide. The electrodes were evaluated in undiluted human urine and attest to the robustness of the ionophore.     

基于酞菁铜衍生物为载体的电极对水杨酸根的选择性电位响应

本文以2,9,16,23-四硝基酞菁铜(II) (Cu(II)TNPc) 和2,9,16,23-四氨基酞菁铜(II) (Cu(II)TAPc) 为载体制备PVC聚合膜,构建了水杨酸根选择性电极,并探讨了该电极的选择性响应性能。研究了增塑剂的性质、载体的含量及阴、阳离子添加剂对电极电位响应的影响。结果表明,基于Cu(II)TNPc为载体的PVC膜电极对水杨酸根 (Sal－) 呈现出优先选择性电位响应。具有最佳电位响应的电极的膜组成是：(w/w) 3.0% Cu(II)TNPc,67.0% o-NPOE,29.5% PVC和0.5% NaTPB。基于该组成的电极的线性响应范围为1.0×10－1－9.0×10－7 mol·L－1,检测下限为7.2×10－7 mol·L-1,斜率为－59.8±0.5 mV/decade;其响应快速,稳定性好,适宜的pH范围是3.0－7.0。并成功运用于了实际样品中水杨酸含量的测定,获得令人满意的结果。     

Novel Plastic Chromium(III)‐Ion Selective Electrodes Based on Different Ionophoric Species and Plasticizing Solvent Mediators

Different ionophoric species, viz.: 18‐crown‐6 (18C6), dibenzo‐18‐crown‐6 (DB18C6) and calix[6]arene (CAX), as electroactive materials, with 2‐nitrophenyloctylether (2‐NPOE), bis(ethylhexyl)sebacate (DOS), dioctyl phthalate (DOP), and didecyl phthalate (DDP) as plasticizing solvent mediators were used to construct Cr³⁺ selective electrodes in a PVC matrix in the ratio (w/w) PVC: ionophore: plasticizer (60 : 2 : 120). Seven electrodes out of the fabricated 12 electrodes, gave best results in terms of working concentration range (1.0×10^?5?1.0×10^?1 M) with a close to Nernstian slope of 18.5 and a Nernstian slope of 20.0 mV/decade of activity. The usable pH range of the sensors is 4.0–7.0. The detection limit of the selected electrodes is ≤1.0×10^?7 M. The response time of the sensors is 8–35 s, depending on the concentration of Cr³⁺ used. The selectivity coefficient values indicate that the electrodes are highly selective for Cr³⁺ over a number of other cations except Pb²⁺ and Na⁺ (for some electrodes). The electrodes have successfully been used to determine Cr³⁺ in certified and real alloys and in effluents of electroplating shops with a precision as relative standard deviation (RSD)<3%, for each of the proposed Cr³⁺‐ion selective electrodes. The results obtained by the proposed ISEs are in good agreement with the results obtained by direct flame AAS method.     

Sequential flow-injection determinations of calcium and magnesium in waters

A tubular PVC membrane electrode for calcium without inner reference solution and a device for location of the reference electrode are described. In the flow-injection system, calcium is determined potentiometrically and then magnesium is determined by atomic absorption spectrometry. The electrode provides linear response to calcium in the range 5 × 10^?5/2-10^?1 M. On-line dilution of the sample allows magnesium determination in the range 0/2-10 mg l^?. Flow rates between 3 and 6 ml min^?1 are possible. The sampling frequency is 60/2-90 h^?1.     

Sensitive Anodic Stripping Voltammetric Copper Ions Determination Performed in Double Deposition and Double Stripping Steps System for Real Water Samples Analysis

The article reports on utilization of double deposition and stripping steps for increasing sensitivity of Cu(II) determination by anodic stripping voltammetry (ASV) at two lead film working electrodes. A significant preconcentration of copper was achieved thanks to utilization of a simple design of four electrodes system that gives possibility to perform one measurement cycle consisting of two deposition and two stripping steps. Due to the fact that deposition step is doubled, the concentration of Pb(II) needed to lead film electrodes formation was significantly reduced as compared to traditional procedures using three electrodes system. The analytical procedure of Cu(II) determination was optimized. The experimental factors: supporting electrolyte's pH and its concentration, lead ions concentration, potential and time of deposition at both working electrodes were studied. The Cu(II) peak current was linearly dependent on its concentration from 5×10^?10 to 2×10^?8 mol L^?1 (deposition time of 270 and 160 s at the first and the second working electrode, respectively). The obtained detection limit for copper ions determination was 2.1×10^?10 mol L^?1. The described procedure was validated by analysis of two water certified reference materials. The described procedure was also utilized for real water sample analysis.     

Mixed Aza‐Thioether Crowns Containing a 1,10‐Phenanthroline Sub‐Unit as Neutral Ionophores for Silver Ion

Three different recently synthesized aza‐thioether crowns containing a 1,10‐phenanthroline sub‐unit (L1–L3) and a corresponding acyclic ligand (L4) were studied to characterize their abilities as silver ion ionophores in PVC‐membrane electrodes. Novel conventional silver‐selective electrodes with internal reference solution (CONISE) and coated graphite‐solid contact electrodes (SCISE) were prepared based on one of the 15‐membered crowns containing two donating S atoms and two phenanthroline‐N atoms (L1). The electrodes reveal a Nernstian behavior over wide Ag⁺ ion concentration ranges (1.0×10^?5?1.0×10^?1 M for CONISE and 5.0×10^?8?4.0×10^?2 M for SCISE) and very low limits of detection (8.0×10^?6 M for CONISE and 3.0×10^?8 M for SCISE). The potentiometric response is independent from pH of the solution in the pH range 3.0–8.0. The electrodes manifest advantages of low resistance, very fast response and, most importantly, good selectivities relative to a wide variety of other cations. The electrodes can be used for at least 2 months (for CONISE) and 4 months for (SCISE) without any appreciable divergence in potentials. The electrodes were used as an indicator electrode in the potentiometric titration of Ag⁺ ion and in the determination of silver in photographic emulsions and in radiographic and photographic films.     

A Potentiometric Sensor for Cd2+ Based on Carbon Nanotube Paste Electrode Constructed from Room Temperature Ionic Liquid,Ionophore and Silica Nanoparticles

A novel and effective potentiometric sensor for the rapid determination of Cd²⁺ based on carbon paste electrode consisting of the room temperature ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate, multiwalled carbon nanotubes, silica nanoparticles and ionophore was constructed. The prepared composite has a low potential drift, high selectivity and fast response time, which leads to a more stable potential signal. A linear dynamic range of 4.50×10^?9–1.00×10^?1 mol L^?1 with a detection limit of 2.00×10^?9 mol L^?1 was obtained. The modified electrode was successfully applied to the accurate determination of trace amounts of Cd²⁺ in environmental and biological samples.