Spectrophotometric determination of vanadium(IV) with nitrilotriacetic acid

A new and convenient spectrophotometric method for the estimation of vanadium(IV) with NTA is described. The minimum ratio of metal ion to ligand, working pH, wavelength for maximum absorbance of the complex ion, and the effect of various cations and anions are described. The complex ion obeys Beer's law in the concentration range 1–32 mmol/liter of the vanadium(IV) ion. It is observed that iron(II), cobalt(II), nickel(II), copper(II), and oxidizing anions such as chromate and nitrite interfere in this determination, whereas managanese(II), chromium(III), iron(III), and anions like nitrate, chloride, bromide, iodide, thiocyanate, sulfate, and sulfite do not have any effect. Excessive amounts of acetate, phosphate, oxalate, tartrate and thiosulfate must also be avoided in this determination. Anions and cations which interfere in the determination of vanadium(IV) by NTA should not be present in the system.     

Preconcentration of Nickel(II) in White Wine Using Quinoxaline-2,3-dithiol and a Finely Divided Anion-Exchange Resin for the Determination by Solid-Phase Spectrophotometry

A simple and sensitive method for the determination of trace amounts of nickel(II) is described. The method is based on the adsorptive enrichment of nickel(II) as the complex with quinoxaline-2,3-dithiol using a finely divided anion-exchange resin, collection of the resin on a membrane filter by filtration, and direct measurement of the absorbance of the resultant circular thin layer by reflective spectrophotometry at 605 nm. In the presence of interfering cations such as copper(II) and cobalt(II) a sample solution is first filtered, after the addition of ammonium thiocyanate and Zephiramine, to extract these cations onto a membrane filter as the ion-pair precipitate formed between the metal-thiocyanate complex anions and Zephiramine cations, then nickel(II) in the filtrate is determined. Interferences from iron(III), silver(I), bismuth(III), cadmium(II), mercury(II), indium(III), palladium(II), platinum(IV), tin(IV), and zinc(II) can also be eliminated. The proposed method was applied to the determination of nickel in white wine. The concentrations of nickel found in 5-ml aliquots of 10 different wine samples were in the range 16.1-68.0 ng ml⁻¹.     

Extraction of manganese(II) with dithizone and potassium thiocyanate on foam sorbents for spectrophotometric determination in silicates

A method for selective extraction of Mn(II) with dithizone and potassium thiocyanate has been described. The method involves formation of a Mn(II)-thiocyanate-dithizone complex in a hexamine medium containing potassium thiocyanate (2.8M), dithizone (5.5-6.5 x 10(-5)M) and hydroxylamine hydrochloride (0.25%) at pH approximately 6 followed by extraction of the complex on polyurethane foam using batch squeezing mode within 1 hr. The sorbed Mn-thiocyanate-dithizone complex is eluted with acetone and made alkaline with 0.5 ml of a stabilizer solution (19 ml 2M NH(3) solution + 1 ml 5% hydroxylamine hydrochloride). The absorbance of the solution is measured at 506 nm. The adverse effect due to Pb may be obviated by separating the Pb as the sulphate during decomposition of sample and that due to iron may be removed before extraction of Mn by any suitable method. The other interfering elements (Cd, Zn, Ni, Co, Cu, etc.) are masked with KCN (6 x 10(-3)M optimum) solution. The method obeys Beer's Law from 0.1 to 2.0 mug Mn/ml. The method has been applied to various silicates, carbonates and glasses.     

Spectrophotometric estimation of cobalt(II) with nitrilotriacetic acid

A convenient and efficient method for the estimation of cobalt(II) ions in the presence of other metal ions is described. Interference of metal ions such as iron(II), iron(III), nickel(II), manganese(II), and copper(II) have been investigated. Only iron(III) ions seriously affect this determination. Copper(II) and nickel(II) ions do not interfere if present in a molar-ratio less than 1:2 in the cobalt(II) ion solution. Cobalt(II)-nickel(II) and cobalt(II)-copper(II) binary mixtures can be efficiently analyzed at selective wavelengths.     

Organic solvent-soluble membrane filters for the preconcentration and spectrophotometric determination of iron(II) traces in water with Ferrozine

An organic solvent-soluble membrane filter (MF) is proposed for the simple and rapid reconcentration with subsequent spectrophotometric determination of trace levels of iron (II) in water. Iron (II) is collected on a nitrocellulose membrane filter as ion associate of an anionic complex, which is formed by iron (II) and Ferrozine and a cation-surfactant. The ion-pair compound and the MF can be dissolved in small volumes of 2-ethoxyethanol and the absorbance of the resulting solution is measured at 560 nm against a reagent blank with molar absorptivity of 4.01 × 10⁴ L mol^–1 cm^–1. Beer’s law is obeyed over the concentration range 0–10 μg L^–1 of iron (II) in water and the detection limit is 0.03 μg L^–1 with a 50-fold enrichment factor. The proposed method can satisfactorily be applied to the determination of iron (II) in natural water and sea water.     

Surface-enhanced Raman spectroscopy of free bilirubin and bilirubin complexes with transition metals iron(II), nickel(II) and cobalt(II)

The surface-enhanced Raman scattering (SERS) spectra of free bilirubin and bilirubin complexes with transition metals [iron(II), nickel(II) and cobalt(II)] are investigated on colloidal silver. Free bilirubin is found to be adsorbed on colloidal silver at the lactam and dicarboxylate oxygens. The addition of some transition metal ions results in rapid, square planar complex formation and the complex ratio of bilirubin with the metal ion is 1:1.     

硫氰酸汞间接分光光度法测定三乙基铝中氯的含量

建立了测定三乙基铝中氯含量的硫氰酸汞间接分光光度法。在酸性溶液中,硫氰酸汞与氯离子反应后游离出硫氰酸根离子,硫氰酸根离子与铁离子反应生成红色硫氰酸铁络合物,于460 nm波长处测定该络合物的吸光度,从而间接获得氯的含量。对测量过程的波长、酸度、显色剂的用量、显色剂的稳定性等因素进行了探讨。氯的质量在0~50μg范围内与吸光度呈良好的线性关系,线性相关系数r=1.000 0,测定结果的相对标准偏差为0.07%~0.20%(n=6),加标回收率为94.8%~105.0%。该法适用于三乙基铝工业品中氯含量的测定。     

Flow-injection simultaneous determination of iron(III) and copper(II) and of iron(III) and palladium(II) based on photochemical reactions of thiocyanato-complexes

The flow injection analysis systems have been developed for the simultaneous determination of iron(III) and copper(II) and of iron(III) and palladium(II) based on the photochemical reactions of their thiocyanato-complexes. In the first system, a sample solution was injected in to nitric acid solution and mixed with ammonium thiocyanate solution, followed by spectrophotometric monitoring of the thiocyanato-complexes formed. Another aliquot of the same sample solution was injected and the thiocyanato-complexes formed in the same way were irradiated by UV light before spectrophotometric monitoring. In another system, the absorbance of thiocyanato-complexes formed by each sample injection was monitored with two flow cells aligned with the same optical path before and after UV irradiation. The difference in the extent of photochemical decomposition of the thiocyanato-complexes enabled simultaneous determinations of iron(III) and copper(II) and of iron(III) and palladium(II) at levels of several μg ml⁻¹ to some tens μg ml⁻¹ in their admixtures. Sample throughputs are 40 and 20 h⁻¹ by the former and latter systems, respectively.     

Sequential determination of iron(II) and iron(III) in pharmaceutical by flow-injection analysis with spectrophotometric detection.

A flow injection procedure for the sequential spectrophotometric determination of iron(II) and iron(III) in pharmaceutical products is described. The method is based on the catalytic effect of iron(II) on the oxidation of iodide by bromate at pH = 4.0. The reaction was monitored spectrophotometrically by measuring the absorbance of produced triiodide ion at 352 nm. The activating effect for the catalysis of iron(II) was extremely exhibited in the presence of oxalate ions, while oxalate acted as a masking agent for iron(III). The iron(III) in a sample solution could be determined by passing through a Cd-Hg reductor column introduced in the FIA system to reduce iron(III) to iron(II), which allows total iron determination. Under the optimum conditions, iron(II) and iron(III) could be determined over the range of 0.05 - 5.0 and 0.10 - 5.0 microg ml(-1), respectively with a sampling rate of 17 +/- 5 h(-1). The experimental limits of detection were 0.03 and 0.04 microg ml(-1) for iron(II) and iron(III), respectively. The proposed method was successfully applied to the speciation of iron in pharmaceutical products.     

Gas chromatography of ternary complexes of manganese(II), iron(II), cobalt(II) and nickel(II) with hexafluoroacetylacetone and DI-n-butylsulphoxide

The gas Chromatographic behaviour of the ternary complexes of selected bivalent first-row transition metal ions with 1,1,1,5,5,5-hexafluoro-2,4-pentanedione H(HFA), and di-n-butylsulphoxide, DBSO, was studied. Calibration plots of peak area vs. amount of metal injected were linear over a range of 60–900 ng for manganese(II), iron(II), cobalt(II) and nickel(II). The average relative standard deviation was less than 3·0% for all the metals studied. Detection limits of 60, 109, 112 and 115ng for cobalt(II), nickel(II), iron(II) and manganese(II), respectively, were obtained with flame-ionization detection. Various liquid phases, including OV-1, SE-30, and Dexsil 300 were used. The best results were obtained on columns of 5% Dexsil 300. No appreciable thermal decomposition was observed on stainless-steel or glass columns, but the best formed peaks were obtained on all-glass columns. The elution of the metallic species was confirmed by venting the exit gases from the gas chromatograph directly into an atomic-absorption spectrophotometer.     

Reversed Phase Extraction Chromatographic Separation of Manganese(II) with Tributyl Phosphate

Abstract

The extraction chromatography of manganese(II) was developed using tributyl phosphate as extractant from thiocyanate media with silica gel as the stationary phase. Manganese was extracted from 1.5 M ammonium thiocyanate, stripped with mineral acids and determined spectrophotometrically at 450 nm. It was separated from alkali metals, Mo(VI), nickel, silver and lead by selective extraction, and from iron(III), zinc, cobalt by selective stripping. The method was extended for the analysis of manganese in samples of soil and minerals.     

Determination of platinum (II,IV) and palladium(II) as thiocyanate complexes by capillary zone electrophoresis analysis of carboplatin and similar drugs

The thiocyanate complexes of Pd(II), Pt(II) and Pt(IV) were studied by capillary zone electrophoresis. Pd(II) can be detected in the form of the thiocyanate complex at 305 nm with higher sensitivity than in the form of its chloro complex (absorption maximum 214 nm). A detection limit equal to 5 ppb for Pd has been finally achieved. The possibility of simultaneous determination of Pd(II) and Pt(IV) in the form of thiocyanate complexes has also been demonstrated. When the method optimized for the determination of Pt(II) was applied to the drugs Cykloplatin and Ribocarbo (containing carboplatin) and Platidiam (containing cisplatin), good agreement of the platinum content with the declared value was obtained. Samples of vehicle exhaust particulates (National Institute for Environmental Studies, Japan, No. 8 reference material) were also analyzed.     

Determination of heavy metals at sub-ppm levels in seawater and dialysis solutions by FAAS after tetrakis(pyridine)-nickel(II)bis(thiocyanate) coprecipitation.

A coprecipitation method has been developed for the determination of Cr(III), Mn(II), Fe(III), Co(II), Cu(II), Cd(II) and Pb(II) ions in aqueous samples by flame atomic absorption spectrometry (FAAS) with the combination of pyridine, nickel(II) as a carrier element and potassium thiocyanate as an auxiliary complexing agent. The obtained coprecipitates were dissolved with nitric acid and measured by FAAS. The coprecipitation conditions, such as the effect of the pH, amounts of nickel, pyridine and potassium thiocyanate, sample volume, and the standing time of the precipitate formation were examined in detail. It was found that the metal ions studied were quantitatively coprecipitated with tetrakis(pyridine)-nickel(II)bis(thiocyanate) precipitate (TP-Ni-BT) in the pH range of 9.0 - 10.5. The reliability of the results was evaluated by recovery tests, using synthetic seawater solutions spiked with the analyte metal ions. The obtained recoveries ranged from 96 to 101% for all of the metal ions investigated. The proposed method was validated by analyses of two certified reference materials (NIST SRM 2711 Montana soil and HPS Certified Waste Water Trace Metals Lot #D532205). It was also successfully applied to seawater and dialysis solution samples. The detection limits (n = 25, 3s) were in the range of 0.01-2.44 microg l(-1) for the studied elements and the relative standard deviations were < or =6%, which indicated that this method could fully satisfy the requirements for analysis of such samples as seawater and dialysis solution having high salt contents.     

Quantitation of ranitidine in pharmaceuticals by titrimetry and spectrophotometry using potassium dichromate as the oxidimetric reagent

Four new methods are described for the determination of ranitidine hydrochloride (RNH) in bulk drug and in formulations employing titrimetric and spectrophotometric techniques and using potassium dichromate as the oxidimetric reagent. In titrimetry (method A), RNH is treated with a measured excess of dichromate in acid medium, and the unreacted oxidant is back titrated with iron(II) ammonium sulfate. The three spectrophotometric methods are also based on the oxidation of RNH by a known excess of dichromate under acidic conditions followed by the determination of surplus oxidant by three different reaction schemes. In one procedure (method B), the residual dichromate is treated with diphenylcarbazide and the absorbance measured at 540 nm. Calculated amount of iron(II) is added to residual dichromate and the resulting iron(III) is complexed with thiocyanate and measured at 470 nm (method C). Method D involves reduction of unreacted dichromate by a calculated amount of iron(II) and estimation of residual iron(II) as its orthophenanthroline complex after raising the pH, and measuring the absorbance at 510 nm. In all the methods, the amount of dichromate reacted corresponds to the drug content. The experimental conditions are optimized. The titrimetric procedure is applicable over 5–10 mg range. In spectrophotometric methods, Beer’s law is obeyed in the ranges 5–50, 5–80, and 10–100 µg ml^?1 for method B, method C, and method D, respectively. The methods were validated for accuracy, precision and recovery. The proposed methods were applied to the analysis of RNH in the tablet and the injection forms, and the results were in agreement with those obtained by the reference method.     

Indirect spectrophotometric determination of thiocyanate by extraction as bisthiocyanatobisquinolinemercury(II) complex and its ligand substitution reaction with dithizone

Thiocyanate forms with mercury(II) in the presence of quinoline a mixed-ligand mercury(II) complex, bisthiocyanatobisquinolinemercury(II), and is extracted into chloroform. This mixed-ligand complex is treated with dithizone and forms the bisdithizonatomercury(II) complex. Maximum and constant absorbance of the dithizone complex is obtained when thiocyanate is extracted at pH 5.1-6.5, and Beer's law is obeyed at 498 nm, where the difference in absorbance between the dithizone complex and dithizone is largest. Chloride, bromide, iodide, cyanide and large amounts of ammonium and copper(II) ions interfere.     

Spectrophotometric determination of iron (II) with quinisatin oxime

A sensitive spectrophotometric determination of iron is based on the blue color (absorption maximum at 660 mμ) formed by reaction of iron (II) with quinisatin oxime in buffered solution containing ethyl alcohol and a small amount of dimethylformamide. The color develops rapidly and is stable for a few h. The absorbance is well reproducible, and conforms to Beer's law. The optimum concentration range at 1 cm optical path is about 0.5 to 2.5 p.p.m. of iron. Small amounts of iron(III) are reduced by the reagent and cause no difficulty. Cobalt and nickel interfere. Iron(II) and quinisatin oxime react in a 1:3 mole ratio; some possible modes of complex formation are suggested.     

Analysis of metals by solid-liquid separation after liquid-liquid extraction spectrophotometric determination of palladium(II) by extraction of palladium dimethylglyoximate with melted naphthalene

A method of liquid-liquid extraction of palladium di-methylglyoximate with molten naphthalene followed by solid-liquid separation is successfully applied to palladium. The complex between palladium and dimethylglyoxime is easily extracted into molten naphthalene. After extraction, the very fine solidified naphthalene crystals are dissolved in chloroform, and the absorbance of the resultant solution is measured at 370 nm against a reagent blank. Beer's law is obeyed for 30-370 mug of palladium in 10 ml of chloroform, and the molar absorptivity is calculated to be 1.72 x 10(4) l.mole.(-1)mm(-1). Various alkali metal salts and metal ions do not interfere. The interference of nickel(II) is overcome by the extraction at pH 2, and that of iron(III) by masking with EDTA or by reduction to iron(II). The method is rapid and accurate.     

Simultaneous spectrophotometric determination of nickel and iron in copper-base alloy with bromo-PADAP

The reaction of nickel (II) with Br-PADAP, in the presence of tergitol NPX surfactant, forms a complex with absorption peaks at 520 and 560 nm. The iron(II)-Br-PADAP system at the same conditions forms a chelate with absorption peaks at 560 and 748 nm. This allows the simultaneous spectrophotometric determination of nickel and iron by measuring the absorbance at 560 and 748 nm. The proposed method, at ph 4.0-5.7, shows a molar absorptivity of 1.22 x 10(5)l . mole(-1) . cm(-1) for nickel at 560 nm and 8.20 x 10(4)l . mole(-1) . cm(-1) at 560 nm and 3.35 x 10(4)l . mole(-1) . cm(-1) at 748 nm for iron(II). Beer's law is obeyed up to 0.40 mu/ml of nickel(II) and up to 0.65 mu/ml of iron(II). Thiosulphate as masking agent allows the simultaneous determination of iron and nickel in the presence of high concentrations of copper. The ethylene glycol 2-(2-amino-ethyl) tetracetic acid provides the elimination of many other interferences. The method has been applied successfully to the simultaneous determination of nickel and iron in reference samples.     

Liquid chromatographic determination of cobalt(II), copper(II) and iron(II) using 2-thiophenaldehyde-4-phenyl-3-thiosemicarbazone as derivatizing reagent

The complexing reagent 2-thiophenaldehyde-4-phenyl-3-thiosemicarbazone (TAPT) was examined for high performance liquid chromatographic (HPLC) separations of cobalt(II), copper(II) and iron(II) or cobalt(II), nickel(II), iron(II), copper(II) and mercury(II) as metal chelates on a Microsorb C-18, 5-mum column (150x4.6 mm i.d.) (Rainin Instruments Woburn, MA, USA). The complexes were eluted isocratically with methanol:acetonitrile:water containing sodium acetate and tetrabutyl ammonium bromide (TBA). UV detection was at 254 nm. The solvent extraction procedure was developed for simultaneous determination of the metals, with detection limits within 0.5-2.5 mug ml(-1) in the final solution. The method was applied for the determination of copper, cobalt and iron in pharmaceutical preparation.     

Ion paired chromatography of iron (II,III), nickel (II) and copper (II) as their 4,7-Diphenyl-1,10-phenanthroline chelates

A reversed phase ion-paired chromatographic method that can be used to determine trace amounts of iron (II,III), nickel (II) and copper (II) was developed and applied to the determination of iron (II) and iron (III) levels in natural water. The separation of these metal ions as their 4,7-diphenyl-1,10-phenanthroline (bathophenanthroline) chelates on an Inertsil ODS column was investigated by using acetonitrile-water (80/20, v/v) containing 0.06 M perchloric acid as mobile phase and diode array spectrophotometric detection at 250-650 nm. Chromatographic parameters such as composition of mobile phase and concentration of perchloric acid in mobile phase were optimized. The calibration graphs of iron (II), nickel (II) and copper (II) ions were linear (r > 0.991) in the concentration range 0-0.5, 0-2.0 and 0-4.0 mug ml(-1), respectively. The detection limit of iron (II), nickel (II) and copper (II) were 2.67, 5.42 and 18.2 ng ml(-1) with relative standard deviation (n = 5) of 3.11, 5.81 and 7.16% at a concentration level of 10 ng ml(-1) for iron (II) and nickel (II) and 25 ng ml(-1) for copper (II), respectively. The proposed method was applied to the determination of iron(II) and iron(III) in tap water and sea water samples without any interference from other common metal ions.