Determination of trace metals in sediment standard reference materials by graphite-furnace atomic absorption spectrometry with a stabilized temperature platform

Trace elements (As, Be, Cd, Co, Cr, Cu, Mn, Mo, Ni, Pb, V, Zn) in NBS 1645 (river sediments), NBS 1646 (estuarine sediment), MESS-1 and BCSS-1 (marine sediments), IAEA SL-1 (Lake Sediment) and IAEA Soil-5, are determined by graphite furnace atomic absorption spectrometry with the L'vov platform. The samples (ca. 0.25 g) are dissolved in a mixture of nitric, perchloric and hydrofluoric acids in a PTFE bomb. Results based on direct calibration with simple aqueous solutions are in good agreement with those obtained by the method of standard additions and with recommended values. The relative standard deviations are generally 5–10%. Chromium determinations are also evaluated by inductively-coupled plasma/atomic emission spectrometry.     

流动注射在线预浓集原子吸收光谱分析废水中的Cd~（2＋）、Fe~（3＋）、Zn~（2＋）

将ＳＨＡ无机离子交换剂应用于在线预浓集ＦＩＡ—ＡＡＳ系统中，对痕量Ｃｄ、Ｚｎ、Ｆｅ的测定进行了研究。三个元素的检出限分别为０．１ｎｇ／ｍｌ，０．３ｎｇ／ｍｌ，０．６ｎｇ／ｍｌ。相对标准偏差小于３％（定时进样）和５％（定量进样）．用标准物分析和回收实验评价了方法的准确度．对各种实际水样的测定结果今人满意。     

Total Sulfur Concentration in Tissues of Control and Cadmium-Exposed Rats by Inductively Coupled Plasma Atomic Emission Spectrometry

Abstract

Total sulfur (S) concentration in biological samples was determined simultaneously with metal concentrations by inductively coupled plasma-atomic emission spectrometry (ICP).

A 0.2 g portion of liver and other tissues were wet-digested with 1.0 ml mixed acid (HNO₃ : HCLO₄ = 5 : 1, v/v) at 130 – 150 °C. The solution was concentrated to about 0.1 ml and then diluted to 5.0 ml with double distilled water. Concentration of S was determined by ICP using ammonium sulfate as a standard S compound. Sulfur and other element concentrations in an NBS standard reference material (Bovine Liver SRM 1577) were within the certified values by this method.

Concentrations of total S, cadmium (Cd), copper (Cu) and zinc (Zn) in the liver, kidney, spleen, lung, pancreas and blood serum were compared between the control and Cd-exposed rats. The three metal concentrations were increased significantly by Cd exposure. However, S concentration was not altered significantly in the liver and other tissues despite the extensive induction of metallothionein (MT) by the repeated Cd exposure. Metallothionein induced by the accumulated Cd (121 μg/g) and Zn (48 μg/g) in the liver was estimated to account for at maximum 7 % of the total S by assuming that the increased metals were all bound to MT. Concentration of S in blood serum was decreased significantly by Cd loading.     

Dithione as chelator in the flow injection separation and pre-concentration system of trace metals in biological samples

Dithione was used as chelator in the flow injection-knotted reactor separation and pre-concentration system coupled to flame atomic absorption spectrometry to determine trace amounts of Cu, Cd, Zn, Co in biological standard samples. Peak height was used for quantitative purpose. Alkali and alkaline earth elements, which could not chelate with dithione were separated from the objective metals; competition between trace metals were avoided for the strong chelating ability of dithione. Compared to diethyldithiocarbamate and pyrrolidine dithiocarbamate (APDC), dithione was used for multi-element detection with lower chelator concentration and better analytical performance. Concentration factors of 23.4-69.3 were obtained using dithione, with the detection limits of 1.06-2.56 μg/l. The system developed was used to determine trace metals in certified biological reference materials of human hair, pig liver and sea prawn after routine digestion, the results obtained agreed well with the certified values, relative standard deviations of the determinations were at the range of 2.10-3.02%.     

聚丙烯腈微球预富集分离微柱与FAAS联用测定痕量Cd(Ⅱ)和Zn(Ⅱ)

将自制的聚合物微球填充到玻璃柱制备了2.5cm×4 mm i.d.预富集分离柱,并将其与火焰原子吸收光谱(FAAS)法联用,测定了其对Cd2和Zn2+的动态吸附,建立了测定溶液中痕量Cd2+和Zn2+的预富集分离-FAAS方法;优化了对Cd2+和Zn2+的吸附富集与洗脱条件,在室温下,溶液pH为5～6,上样和洗脱液流速...     

Fast on-line ultrasound-assisted extraction coupled to a flow injection-atomic absorption spectrometric system for zinc determination in meat samples

A continuous ultrasound-assisted extraction system connected to a flow injection manifold has been used for the on-line determination of zinc in meat samples by flame atomic absorption spectrometry. An experimental design was used for the optimisation of the continuous manifold. This flow injection methodology allowed a sampling frequency of ca. 80 samples per hour with a relative standard deviation for the whole procedure of 0.3% (for a sample containing 163.6 μg g⁻¹ Zn). The detection limit was 0.6 μg g⁻¹ for a sample amount of 5 mg. Accurate results were obtained by measuring certified reference materials (BCR-186 (pig kidney) and BCR-184 (bovine muscle)). The analytical procedure was applied to different real meat samples with satisfactory results.     

A novel method for the simultaneous determination of Pb (II), Cd (II) and Zn (II) in environmental water samples

A novel UV-VIS spectrophotometric method was developed in this study by using solid phase extraction procedure for the simultaneous preconcentration, separation and determination of trace levels of Pb (II), Cd (II) and Zn (II) ions in various water samples by using Amberlite N,N-bis(salicylidene)cyclohexanediamine (SCHD) resin. This study presents the results of experimental procedures carried out like the adsorption of analytes to the resin, influences of some analytical parameters that effect the recovery such as pH, sample volume, sample flow rate, eluent type and concentration, eluent volume, eluent flow rate and the effects of alkaline metals, earth alkaline metals and some other transition metals. The analytes in the samples with the adjusted pH range of 4–7 were adsorbed on XAD-4-SCHD resin and eluted by using 1.0 mol L^?1 nitric acid. The amounts of ions were determined by using UV-VIS spectrometer. The limits of detection were 0.03, 0.07 and 0.05 µg mL^?1 for Pb (II), Cd (II) and Zn (II), respectively. The accuracy of the method was assured by the analysis of the certified standard water sample NW-TMDA-70.2 and the observed recoveries were above 93%. Different environmental water samples that contain trace amounts of Pb (II), Cd (II) and Zn (II) were analysed by using the method developed in this study. Same samples were also analysed by ICP-MS for comparison and almost the similar results were observed. The method developed in this study was successfully applied to the various environmental water samples to determine the trace levels of Pb (II), Cd (II) and Zn (II) ions.     

Determination of cadmium and lead at low levels by using preconcentration at fullerene coupled to thermospray flame furnace atomic absorption spectrometry

A new and sensitive method for Cd and Pb determinations, based on the coupling of thermospray flame furnace atomic absorption spectrometry and a preconcentrator system, was developed. The procedure comprised the chelating of Cd and Pb with ammonium pyrrolidinedithiocarbamate with posterior adsorption of the chelates on a mixture (40 mg) of C₆₀ and C₇₀ at a flow rate of 2.0 ml min⁻¹. These chelates were eluted from the adsorbent by passing a continuous flow of ethanol (80% v/v) at 0.9 ml min⁻¹ to a nickel tube placed in an air/acetylene flame. After sample introduction into the tube by using a ceramic capillary (0.5 mm i.d.), the analytical signals were registered as peak height. Under these conditions, improvement factors in detectability of 675 and 200 were obtained for Cd and Pb, respectively, when compared to conventional flame atomic absorption spectrometry. Spiked samples (mineral and tap waters) and drinking water containing natural concentrations of Cd were employed for evaluating accuracy by comparing the results obtained from the proposed methodology with those using electrothermal atomic absorption spectrometry. In addition, certified reference materials (rye grass, CRM 281 and pig kidney, CRM 186) were also adopted for the accuracy tests. Due to the good linearity ranges for Cd (0.5–5.0 μg l⁻¹) and Pb (10–250 μg l⁻¹), samples with different concentrations could be analyzed. Detection limits of 0.1 and 2.4 μg l⁻¹ were obtained for Cd and Pb, respectively, and RSD values <4.5% were observed (n=10). Finally, a sample throughput of 24 determinations per hour was possible.     

Determination of trace amounts of cadmium, lead, copper and zinc in natural waters by inductively coupled plasma atomic emission spectrometry with thermospray nebulisation, after enrichment on Chelex-100

Enrichment on Chelex-100, followed by evaporation when necessary, was used for the pre-concentration of Cd, Pb, Cu and Zn from natural waters. The measurements were carried out with inductively coupled plasma atomic emission spectrometry using a thermospray nebulisation system to reach the required sensitivity. The detection limits corresponding to three times the standard deviation of the blank (in 1% v/v HNO3) after a 30-fold enrichment are 0.02 microgram l-1 for Cd, 0.33 microgram l-1 for Pb and 0.03 microgram l-1 for Cu and Zn. Matrix effects, which are fairly serious with thermospray nebulisation, were taken into account by using the standard additions method. Results obtained for several river water samples were compared with those found by analysis of the non-enriched sample with inductively coupled plasma mass spectrometry or graphite furnace atomic absorption spectrometry. In all instances the agreement was satisfactory.     

Determination of Cd in sonicate slurries and leachates of biological and environmental materials by FI-CV-AAS

An analytical method for Cd analysis in solid samples which combines the ultrasonic slurry formation with cold vapour generation and atomic absorption spectrometry is described. The samples are suspended in HCl and sonicated until homogeneous and reduced particle size slurry formation. Several aspects were studied: acidity of the medium, sonication time, and slurry formation in different matrices. The procedure described permits the use of direct calibration, with KCN addition as masking agent of interfering ions (Cu, Pb, Ni and Zn) present in the environmental matrices. Supernatant analysis of these last samples experimentally shown that preparation of the suspension with 6 mol l(-1) HCl concentration led to quantitative extraction of Cd. Biological materials analysis needed the use of the standard addition calibration method due to the high matrix effect observed. Supernatant analysis in biological samples does not give a total Cd recovery for all of them. The detection limits observed for Cd were 0.05 and 0.2 mug l(-1) for supernatant and slurry analysis respectively in environmental samples, while in biological samples were 0.2 and 0.6 mug l(-1) for supernatant and slurry analysis, respectively. In all case the better precision was obtained for supernatant analysis (3-6%) than slurry analysis (6-12%). The results obtained by analysing different reference materials (sewage sludge, city waste incineration, Antarctic krill and human hair) showed good agreement with the certified value confirming the validity of such a method for Cd determination instead to wet digestion procedures.     

Solid-phase extraction using multiwalled carbon nanotubes and quinalizarin for preconcentration and determination of trace amounts of some heavy metals in food,water and environmental samples

A solid phase extraction procedure has been developed using multiwalled carbon nanotubes (MWCNTs) as a solid sorbent and quinalizarin [1,2,5,8-tetrahydroxyanthracene-9,10-dione] as a chelating agent for separation and preconcentration of trace amounts of some heavy metal ions, Cd(II), Cu(II), Ni(II), Pb(II) and Zn(II) before their determination by flame atomic absorption spectroscopy (FAAS). The influences of the analytical parameters, including pH, amounts of quinalizarin and adsorbent, sample volume, elution conditions such as volume and concentration of eluent, flow rates of solution and matrix ions, were investigated for the optimum recoveries of the analyte ions. No interference effects were observed from the foreign metal ions. The preconcentration factor was 100. The detection limit (LOD) for the investigated metals at the optimal conditions were observed in the range of 0.30–0.65 μg L^?1. The relative standard deviation (RSDs), and the recoveries of standard addition for this method were lower than 5.0% and 96–102%, respectively. The new procedure was successfully applied to the determination of analytes in food, water and environmental samples with satisfactory results.     

六极杆碰撞反应池–ICP–MS法测定海水中痕量金属元素

建立了直接稀释法测定海水中痕量金属元素Cr,Cu,Zn,Cd,Pb的方法。样品经稀释10倍后,使用基体匹配及内标校正,采用六极杆碰撞反应池–电感耦合等离子体质谱仪直接测定稀释后海水样品中的5种元素Cr,Cu,Zn,Cd,Pb。各元素在0.0~100μg/L范围内均呈现良好的线性关系,线性相关系数(r~2)均大于0.999 0,方法检出限为0.004~0.209μg/L。测定结果的相对标准偏差为2.4%~4.4%(n=6),加标回收率为92%~113%。该方法简单快捷,适用于近岸海水中痕量元素Cr,Cu,Zn,Cd,Pb的分析。     

Effect of ultrasound agitation on the release of heavy elements in Certified Reference Material of human hair (CRM BCR 397)

An ultrasonic-assisted leaching procedure was developed for the determination of heavy elements (As, Cu, Cd, Pb, and Zn) in Certified Reference Material of human hair (CRM 397) provided from the Community Bureau of Reference (BCR) of the Commission of the European Community. Concentrated nitric acid-30% hydrogen peroxide (2 + 1) was used for the leaching method. The effects of different factors on acid leaching of elements, such as presonication time (without ultrasonic stirring), sonication or exposure time to ultrasound, and temperature of the ultrasonic bath have been investigated. Optimum values of these parameters were selected for the maximum extraction of heavy metals from CRM BCR 397 and human scalp hair samples of normal healthy males. To check the validity of the proposed method, a wet acid digestion method was used to obtain the total elemental concentration in CRM BCR 397 and scalp hair samples. Cu and Zn in leachate and digests were measured by flame atomic absorption spectrometry using a conventional air/acetylene flame, while As, Cd, and Pd were determined by electrothermal atomic absorption spectrometry. Under optimized conditions, the recovery for Zn, Cd, Pd, As, and Cu was 98, 98.5, 97.5, 98.2, and 95%, respectively, of those obtained with the wet acid digestion method.     

雷公藤的药效及毒性与微量元素的研究

雷公藤是一种药效大、毒性也大的中药。研究了雷公藤的28种无机元素，发现其有益元素铁、锰、锌、硒含量较高．其有害元素铅、砷、镉含量也较高，与其药效和毒性一一相对应。雷公藤对风湿性关节炎、肾病、肝脏病、皮肤病的疗效．与铁、锰、锌、硒在人体中生物学机理一致。雷公藤对消比道、心血管、肝脏、泌尿系统、造血系统的毒害作用，与铅、砷、镉在人体中的生物学效应一致。所以在使用雷公藤时，应考虑到微量元素作用．可提高雷公藤的疗效，降低其毒性。     

Phenolic compounds,antioxidant activity and Cu,Zn, Cd and Pb content in wild and cultivated cranberries and blueberries

The aim of this study was to determine the content of Cu, Zn, Cd and Pb and the total polyphenol (TP) content as well as the total antioxidant capacity (TAC) in wild cranberries and blueberries collected from different localities of the Slovakia and to compare them with properties of six cranberry and six highbush blueberry cultivars obtained from the research centre. Compared with cultivated cranberries (Cu, Zn, Cd and Pb content: 0.642, 1.496, 0.015 and 0.050 mg/kg FM) in wild fruits, higher Cu (by 37%) and lower Zn, Cd and Pb (by 8%, 7% and 44% respectively) were determined using atomic absorption spectrometry method. In wild blueberries, higher Cu, Zn and Pb (by 16%, 209% and 80% respectively) and similar Cd contents were determined compared with cultivated fruits (Cu, Zn, Cd and Pb content: 0.483, 0.541, 0.003 and 0.055 mg/kg FM). The TP contents estimated by spectrophotometry using Folin–Ciocalteau reagent were in intervals 1405–3161 (cranberries) and 1300–3077 (blueberries) expressed as mg GAE/kg FM. While the average TP content determined in wild cranberries was by 31% lower than that in cultivated cranberries, in wild blueberries it was by 97% higher compared with highbush blueberry cultivars. The values of TAC determined by spectrophotometry method using 2,2-diphenyl-1-picrylhydrazyl were in range 20.67–22.22 (cranberries) and 14.03–24.79 (blueberries) expressed as mmol TE/kg FM. In wild cranberries and blueberries, the lower average TAC values compared with cultivated berries were determined (by 1% and 28%, respectively).     

Assessment of Heavy Metal Pollution and Ecological Risk of Roadside Soils in Tlemcen (Algeria) Using Flame-Atomic Absorption Spectrometry

In Algeria, few studies have been conducted on the evaluation of roadside soil pollution. A total of 34 soil samples (28 roadside and 6 off-road) was obtained at 0–20?cm depth along the RN 35 national road. Heavy metal (Cd, Cr, Cu, Fe, Ni, Pb, and Zn) contents were extracted using aqua regia digestion and determined using atomic absorption spectrometry. Background values of heavy metal contents were determined using the robust statistical method of median plus two times the median absolute deviation. Single- and multi-element pollution and ecological risk indices were calculated. The results showed that background values were 2.5?±?0.3, 64.9?±?8.1, 28.0?±?4.1, 29371.5?±?4403.0, 32.9?±?4.4, 72.2?±?12.8, and 445.1?±?62.9?mg/kg for Cd, Cr, Cu, Fe, Ni, Pb, and Zn, respectively. The results were all higher than their corresponding median values. Single-element pollution indices (enrichment factor and geoaccumulation index) showed that the pollution is primarily due to Pb and Zn. Multi-element pollution index (Nemerow index) indicated that only 3% of the soil samples are strongly contaminated, whereas 23% are seriously contaminated. The potential ecological risk index showed that Cd is the most harmful element, followed by Pb and Zn. 65% of the soil samples had moderate potential ecological risk, while only 3% had considerable potential ecological risk. This study may be used as a baseline for future monitoring and as a tool for decision-making regarding environmental protection policies and sustainability of this semiarid agroecosystem.     

Solvent extraction with ammonium pyrrolidinedithiocarbamate and 2,6-dimethyl-4-heptanone for the determination of trace metals in effluents and natural waters

A method is described for the determination of ten trace metals (V, Cr, Fe, Co, Ni, Cu, Zn, Mo, Cd, Pb) in aqueous samples by simultaneous solvent extraction followed by flame atomic absorption spectrometry. 2,6-DimethyI-4-heptanone is preferred to 4-methyl-2-pentanone as the solvent, and ammonium pyrrolidinedithiocarbamate to sodium diethyl-dithiocarbamate as the extractant except when relatively large amounts of iron are present. Calibration graphs are linear, usually over the range 0–50 μg l^-1. The effects of interfering substances, in particular iron, are shown, and the need for calibration by standard additions is demonstrated. The general need for preoxidation of samples is discussed.     

Determination of Cd, Co, Cu, Mn, Ni, Pb, and Zn by Inductively Coupled Plasma Mass Spectroscopy or Flame Atomic Absorption Spectrometry after On-line Preconcentration and Solvent Extraction by Flow Injection System

The concentrations of Cd, Co, Cu, Mn, Ni, Pb, and Zn in natural and sea waters are too low to be directly determined with by flame atomic absorption spectrometry (FAAS) or graphite furnace atomic absorption spectrometry (GFAAS). Specific sample preparations are requested that make possible the determination of these analytes by preconcentration or extraction. These techniques are affected by severe problems of sample contamination. In this work Cd, Co, Cu, Mn, Ni, Pb, and Zn were determined by inductively coupled plasma mass spectroscopy (ICP-MS) or by atomic absorption spectrometry, in fresh and seawater samples, after on-line preconcentration and following solvent elution with a flow injection system. Bonded silica with octadecyl functional group C₁₈, packed in a microcolumn of 100-μl capacity, was used to collect diethyldithiocarbamate complexes of the heavy metals in aqueous solutions. The metals are complexed with a chelating agent, adsorbed on the C₁₈column, and eluted with methanol directly in the flow injection system. The methanolic stream can be addressed to FAAS for direct determination of Cu, Ni, and Zn, or collected in a vial for successive analysis by GFAAS. The eluted samples can be also dried in a vacuum container and restored to a little volume with concentrated HNO₃and Milli-Q water for analysis by ICP-MS or GFAAS.     

Flow injection analysis of Zn and Co in beverages, biological, environmental and pharmaceutical samples

A new, simple, rapid and selective flow injection analysis (FIA) method for the spectrophotometric quantification (speciation of inorganic and organic form) of Zn and Co with ammonium thiocyanate and malachite green (MG) in the presence of surfactants (CPC and TX-100) is described. The value of apparent molar absorptivity of the Zn- and Co- complexes are (1.23) × 10⁴ and (8.67) × 10³ L mol^–1cm^–1 at absorption maximum, 635 nm, respectively. The detection limit (amount causing a peak height > 3 s) is 15 ppb Zn and 20 ppb Co, whereas their optimum working ranges for the quantitative determinations are 0.05–2.0 ppm Zn and 0.07–2.5 ppm Co in the real samples. The sample thoughput of the method is 120 samples/h at the flow rate of 5.0 mL/min with rel. std. dev. of < ± 1%. The method is free from interferences of almost all ions which are commonly associated with these metals in the complex materials. The composition of the complexes and their reaction mechanism involved are discussed. The effect of FIA and analytical variables for the determination of the metals are optimized. The method has been applied to the quantification of Zn and Co in beverages, biological, environmental, and pharmaceutical samples.     

Developing a robust LC–MS/MS method to quantify Zn‐DTPA,a zinc chelate in human plasma and urine

Quantitation of Zn‐DTPA (zinc diethylenetriamene pentaacetate, a metal chelate) in complex biological matrix is extremely challenging on account of its special physiochemical properties. This study aimed to develop a robust and specific liquid chromatography–tandem mass spectrometry (LC–MS/MS) method for determination of Zn‐DTPA in human plasma and urine. The purified samples were separated on Proteonavi (250 × 4.6 mm, 5 μm; Shiseido, Ginza, Tokyo, Japan) and a C₁₈ guard column. The mobile phase consisted of methanol–2 mm ammonium formate (pH 6.3)–ammonia solution (50:50:0.015, v/v/v), flow rate 0.45 mL/min. The linear concentration ranges of the calibration curves for Zn‐DTPA were 1–100 μg/mL in plasma and 10–2000 μg/mL in urine. The intra‐ and inter‐day precisions for quality control (QC) samples were from 1.8 to 14.6% for Zn‐DTPA and the accuracies for QC samples were from −4.8 to 8.2%. This method was fully validated and successfully applied to the quantitation of Zn‐DTPA in plasma and urine samples of a healthy male volunteer after intravenous infusion administration of Zn‐DTPA. The result showed that the concentration of Zn‐DTPA in urine was about 20 times that in plasma, and Zn‐DTPA was completely (94.7%) excreted through urine in human.