Determination of trace elements in manganese metal and compounds by ion-exchange chromatography and atomic absorption spectrometry : Part 1. Determination of Li,Na, K,Be, Ti(IV), Mg,Ni, Ca and Al

Traces of the specified elements can be separated from 1-g amounts of manganese(II), using a 20-g column of AG50W-X8 cation-exchange resin. The trace elements are separated into four groups and are determined by atomic absorption spectrometry, except titanium, which is determined spectrophotometrically. With the exception of sodium, recoveries for 10 μg amounts vary between 94% (for nickel) and 101% (for magnesium). Relevant elution curves, results for the analysis of synthetic mixtures and for the determination of eight trace elements in samples of manganese metal, manganese chloride and manganese dioxide are presented.     

Quantitative separation of gallium from zinc, copper, indium, iron(III) and other elements by cation-exchange chromatography in hydrobromic acid-acetone medium

Gallium can be separated from Zn, Cu(II), In, Cd, Pb(II), Bi(III), Au(III), Pt(IV), Pd(II), Tl(III), Sn(IV) and Fe(III) by elution of these elements with 0.50M hydrobromic acid in 80% acetone medium, from a column of AG50W-X4 cation-exchange resin. Gallium is retained and can be eluted with 3M hydrochloric acid. Separations are sharp and quantitative except for iron(III) which shows extensive tailing. With 0.20M hydrobromic acid in 80% acetone as eluting agent, all the species above except iron(III) and copper(II) can be separated from gallium with very large separation factors. Only a 1-g resin column and small elution volumes are required to separate trace amounts and up to 0.5 mmole of gallium from more than 1 g of zinc or the other elements. Hg(II), Rh(III), Ir(IV), Se(IV), Ge(IV), As(III) and Sb(III) have not been investigated, but should be separated together with zinc according to their known distribution coefficients. Relevant elution curves, results for the analysis of synthetic mixtures and for amounts of some elements remaining in the gallium fraction are presented.     

火焰原子吸收光谱法分析猫爪草胶囊中铁锌锰的含量

为给猫爪草胶囊药用研究提供依据,采用空气-火焰原子吸收光谱法对猫爪草胶囊中铁锌锰元素的含量进行了测定.结果表明,猫爪草胶囊中,铁为287.8 μg/g,锌为27.4 μg/g,锰为24.6 μg/g.方法精密度为2.67%～4.09%,各元素回收率在96.3%～107.6%之间.该法操作简单、结果准确,是猫爪草胶囊中铁...     

Separation of traces of manganese,cobalt, nickel and copper from gram amounts of tellurium by cation-exchange chromatography in hydrochloric acid/acetone media

Traces of Mn(II), Co(II), and Ni(II) and minor amounts (up to 20 mg of these elements are separated from gram amounts of tellurium by cation-exchange chromatography on small columns (3 g) of macroporous AG MP-50 resin or larger colunns (5 g) of microporous AG 50W-X8 resin. The trace elements are retained from 0.5 M HCl containing 70% acetone while tellurium passes through and is eluted completely with this solution. The trace elements are then eluted with 3.0 M HCl and can be determined by atomic absorption spectrometry. Copper (II) can also be separated but requires a 10-g column of AG MP-50 resin. Separations are sharp and quantitative and only microgram amounts of tellurium remain in the trace element fraction when a 3-g sample of tellurium dioxide is taken; 10-μg amounts of the trace elements were separated from such samples and determined with standard deviations of <1%. Relevant elution curves and results for the analysis of synthetic mixtures are presented.     

Determination of uranium in zircon

A routine fluorimetric procedure is described for the determination of trace amounts of uranium in zircon. It employs the direct extraction of uranyl nitrate with ethyl acetate using phosphate as a retainer for zirconium. Submicrogram amounts or uranium are separated in the presence of 100,000 times the amount of zirconium. The modified procedure has been worked out using synthetic mixtures of known composition and zircon. Results of analyses have an accuracy of 97–98% of the contained uranium and a standard deviation of less than 2.5%.     

Determination of tungsten in silicates and natural waters

Coprecipitation with hydrous manganese dioxide is used for the concentration of tungsten from natural waters (including sea water) and from solutions prepared from silicate rocks and sediments by hydrofluoric acid attack. After dissolution of the hydrous manganese dioxide precipitate in acidified sulphur dioxide solution, cation excliange is used to separate tungsten and molybdenum from other coprecipitated elements, hydrogen peroxide being used as eluant. Molybdenum is separated from tungsten by extraction of its dithiol complex from 24 N hydrochloric acid medium containing citric acid and can be determined photometrically. After destruction of citric acid, tungsten is determined photometrically with dithiol. The overall cliemical yield of th analytical process is 94±1%. The standard deviation of the method is ±0.010 μg for sea water (0.116 μg W/l) and ca 0.05 μg/g for siliceous sediments containing 0.5–1.0 μg W/g.     

Determination of Gold and Palladium in Manganese and Nickel Compounds by Atomic Absorption Spectrometry After Separation by Use of Amberlite XAD-7 Resin

Abstract

A method for preconcentration and determination of traces of Au and Pd from manganese, nickel and their compounds is described. The trace elements are preconcentrated at a small column filled with Amberlite XAD-7 resin. After their eluation the elements are determined by flame AAS. The relative standard deviations (N=10) were found to be lower than 5%; the detection limit (3s, N=20) for Au and Pd in metal samples is 0.07 μg/g.     

Quantitative separation of Al, Ga, In, and Tl by cation exchange chromatography in hydrochloric acid-acetone

Up to 4 mmole (1 mmole each) of tervalent Al, Ga, In and Tl are separated from each other on a 60-ml column of AG50W-X8 resin of 200-400 mesh particle size by cation-exchange chromatography in hydrochloric acid-acetone mixtures. Separations are very sharp and without tailing. Recoveries for amounts from 1-100 mg average 100.0 +/- 0.1 % for the analysis of synthetic mixtures. An anion-exchange method is described for the separation of gallium from the hydrochloric acid-acetone eluate. Relevant cation-exchange distribution coefficients, anion-exchange coefficients for gallium in hydrochloric acid-acetone, an elution curve for all four elements and results of quantitative separations of synthetic mixtures are presented.     

Determination of traces of rare earth elements in high-purity uranium by ion-exchange separation and neutron activation γ-spectrometry

Neutron activation γ-spectrometry is sufficiently sensitive for the determination of traces of rare earth elements but quantitative separation from uranium is essential. The rare earth elements in 0.2 M ammonium carbonate medium are quantitatively retained on Chelex-100, and are quantitatively separated from uranium by recycling the eluate. When 10-g samples are used, neutron activation provides detection limits of 1–20 μg kg^?1. Recoveries of rare earths, checked by spiking with radiotracers, are essentially complete.     

Determination of low atomic number elements at trace levels in uranium matrix using vacuum chamber total reflection X-ray fluorescence

Determinations of low atomic number elements Na, Mg and Al present at trace concentrations in uranium matrix were made by vacuum chamber total reflection X-ray fluorescence spectrometer for the first time. For this purpose, synthetic samples of uranium with known amounts of these low atomic number elements were prepared by mixing different volumes of their solutions with U solution of high purity. The concentrations of these elements in the samples were in the range of 100–300 μg/g with respect to uranium and 10–20 μg/mL in the solutions. Major matrix uranium was separated by solvent extraction with 30% solution of tri-n-butyl phosphate in dodecane. After the solvent extraction, aqueous phase containing trace elements was mixed with Sc internal standard and the samples were analyzed by vacuum chamber total reflection X-ray fluorescence spectrometer having a Cr Kα excitation source. The total reflection X-ray fluorescence results obtained, after blank corrections, indicated an average deviation of 14% from the calculated concentrations of these low atomic number elements on the basis of their preparation. However, the total reflection X-ray fluorescence determined concentration of Mg was exceptionally lower than the calculated concentration in two samples. These studies have shown that vacuum chamber total reflection X-ray fluorescence is a promising technique for the determination of low atomic number elements in uranium matrix after its separation.     

火焰原子吸收光谱法测定芦荟中微量铁、锌含量

用火焰原子吸收光谱法测定了芦荟中铁、锌两种微量元素含量。结果表明,芦荟中铁和锌千含量分别为638、244μg/g。火焰原子吸收光谱法测定样品中铁含量和锌含量的相对标准偏差分别为7．06％,3．63％,加标回收率在95％～102．5％范围内,检测限分别为0．011μg,／mL和0．002μg／mL。     

Titrimetric determination of U(iv) alone and in mixtures with V(IV), Mn(II), Ce(III) and Fe(II)

Summary A rapid and accurate method is described for the potentiometric determination of uranium(IV) with permanganate at room temperature using trace amounts of ortho-phosphoric acid as a catalyst. The procedure has been extended for the differential potentiometric determination of mixtures with vanadium, manganese or cerium. The methods are easy, non-time consuming and free from interference by a large number of foreign ions. Conditions are also developed for the differential photometric determination of uranium and iron in mixtures.Based on these procedures, a differential titrimetric procedure has been developed for determination of iron(III), vanadium(V), chromium(VI) and manganese(VII) [or cerium(IV)] in a single solution at room temperature. This procedure has also been tested on Bureau of Standard samples.

---

Titrimetrische Bestimmung von U(IV) allein und in Mischungen mit V(IV), Mn(II), Ce(III) und Fe(II)Anwendung auf die Analyse von Stählen und Legierungen

Zusammenfassung Eine schnelle und genaue Methode wird beschrieben zur potentiometrischen Bestimmung von Uran(IV) mit Permanganat bei Raumtemperatur unter Verwendung von Spuren Orthophosphorsäure als Katalysator. Das Verfahren wurde auf die differentialpotentiometrische Bestimmung im Gemisch mit V, Mn und Ce ausgedehnt. Die rasch und einfach ausführbare Methode wird durch zahlreiche Fremdionen nicht gestört. Eine differentialphotometrische Bestimmung von U(IV) und Fe(II) im Gemisch wird ebenfalls angegeben, außerdem eine differentialtitrimetrische Bestimmung von Fe(III), V(V), Cr(VI), Mn(VII) [oder Ce(IV)] in einer Lösung. Anwendungsbeispiele für Stähle und Legierungen werden beschrieben.

     

Rapid laser fluorometric method for the determination of uranium in soil, ultrabasic rock, plant ash, coal fly ash and red mud samples

A simple and rapid laser fluorometric determination of trace and ultra trace level of uranium in a wide variety of low uranium content materials like soil, basic and ultra basic rocks, plant ash, coal fly ash and red mud samples is described. Interference studies of some common major, minor and trace elements likely to be present in different, geological materials on uranium fluorescence are studied using different fluorescence enhancing reagents like sodium pyrophosphate, orthophosphoric acid, penta sodium tri-polyphosphate and sodium hexametaphosphate. The accurate determination of very low uranium content samples which are rich in iron, manganese and calcium, is possible only after the selective separation of uranium. Conditions suitable for the quantitative single step extraction of 25 ng to 20 μg uranium with tri-n-octylphosphine oxide and single step quantitative stripping with dilute neutral sodium pyrophosphate, which also acts as fluorescence enhancing reagent is studied. The aqueous strip is used for the direct laser fluorometric measurement without any further pretreatment. The procedure is applied for the determination of uranium in soil, basalt, plant ash, coal fly ash and red mud samples. The accuracy of the proposed method is checked by analyzing certain standard reference materials as well as synthetic sample with known quantity of uranium. The accuracy and reproducibility of the method are fairly good with RSD ranging from 3 to 5% depend upon the concentration of uranium.     

Determination of sulphur in uranium matrix by total reflection X-ray fluorescence spectrometry

The possibility of sulphur determination in uranium matrix by total reflection x-ray fluorescence spectrometry (TXRF) has been studied. Calibration solutions and samples of sulphur in uranium matrix were prepared by mixing uranium in form of a standard uranyl nitrate solution and sulphur in the form of Na₂SO₄ standard solution, prepared by dissolving Na₂SO₄ in Milli-Q water. For major element analysis of sulphur, it was determined without separation of uranium whereas for the trace level determinations, uranium was first separated by solvent extraction using 30% tri-n-butyl phosphate (TBP) in dodecane as an extractant. In order to countercheck the TXRF results, a few samples of Rb₂U(SO₄)₃, a chemical assay standard for uranium, were diluted to different dilutions and sulphur content in these solutions were determined. The TXRF determined results for trace determinations of sulphur in these diluted solutions were counterchecked after addition of another uranium solution, so that sulphur is at trace level compared to uranium, separating uranium from these solution mixtures using TBP extraction and determining sulphur in aqueous phase by TXRF. For such TXRF determinations, Co was used as internal standard and W Lα was used as excitation source. The precision and accuracy of the method was assessed for trace and major element determinations and was found to be better than 8% (1σ RSD) and 15% at a concentration level of 1 μg/mL of sulphur measured in solutions whereas for Rb₂U(SO₄)₃, these values were found to be better than 4 and 13%, respectively.     

The determination of zinc,copper, lead and manganese in phosphate-containing matrices by coprecipitation on iron(III) hydroxide and X-ray fluorescence spectrometry

Trace amounts of zinc, copper, lead and manganese (10–75 μg) are coprecipitated on iron(III) hydroxide at pH 8.5 after masking of phosphate by calcium. Reliable results are obtained for mixtures with widely different concentrations. The limit of detection is about 1 μg.     

火焰原子吸收光谱法分析竹沥胶囊中铁、锌、锰的含量

用火焰原子吸收光谱法测定了竹沥胶囊中铁、锌、锰3种微量元素含量,结果表明,竹沥胶囊中铁为57.8μg/g,锌为16.5μg/g,锰为8.13μg/g,各元素回收率在98%～107%之间。     

Determination of uranium in minerals and rocks

A method is described for the determination of uranium in minerals and rocks by spectrophotometry and fluorimetry. After treatment of the sample with hydrochloric acid, uranium is separated from matrix elements by adsorption on a column of the strongly basic anion-exchange resin Dowex 1 x 8 from an organic solvent system consisting of IBMK, tetrahydrofuran and 12M hydrochloric acid (1:8:1 v v ). Following removal of iron, molybdenum and co-adsorbed elements by washing first with the organic solvent system and then with 6M hydrochloric acid, the uranium is eluted with 1M hydrochloric acid. In the eluate, uranium is determined by means of the spectrophotometric arsenazo III method or fluorimetrically. The suitability of the method for the determination of both trace and larger amounts of uranium was tested by analysing numerous geochemical reference samples with uranium contents in the range 10(-1)-10(4) ppm. In practically all cases very good agreement of results was obtained.     

Simultaneous Determination of Nickel and cobalt in Manganese Sulphate Electrolyte by DMGH2-Sensitized Differential Pulse Polarography

Abstract

A method is described for the simultaneous determination of nickel and cobalt in manganese sulphate electrolyte by the dimethylglyoxime (DMGH₂) sensitized differential pulse polarography. The high manganese sulphate background (1.2M) in the concentrated process plant electrolyte interferes only with the nickel determination and precludes its direct determination. A 50% v/v dilution and an excessive amount (2 × 10^?3M) of the chelating agent are required at pH7.7 for the reliable determination of both elements. Under these conditions, the linear concentration ranges are 0-110 μg/1 for nickel and 0-140 μg/1 for cobalt. The minimum detectable amounts above the levels present in the process plant electrolyte are 2 μg/1 and 1 μg/1 for both elements, respectively. The relative standard deviations for all measurements are between 1 and 3%.     

Solvent extraction separations with bpha. applications to the microanalysis of niobium and zirconium in uranium

A detailed study of the benzoylphenylhydroxylamine (BPHA)-chloroform-hydrochloric acid solvent extraction system with 52 elements is described with emphasis placed on extraction of the easily hydrolyzed transition metals from strong hydrochloric acid. From this study, a separation procedure for hafnium, niobium, tantalum, titanium, vanadium, and zirconium from uranium was developed, and procedures are given for the microanalysis of niobium and zirconium in uranium. Niobium and zirconium are separated from uranium by extraction into BPHA-chloroform from 10-N HCl.The separated elements are then measured colorimetrically as the niobium-4-(2-pyridylazo)resorcinol and zirconium-arsenazo III complexes. The limit of detection is 1 μg/g U.     

A highly selective procedure for the spectrophotometric determination of aluminium with 8-hydroxy-quinoline and its application to the determination of

Aluminium, hydroxyquinolate can be quantitatively extracted by chloroform from an ammoniacal solution containing hydroxyquinoline, complexone and cyanide. Likewise extracted are titanium, vanadium, tantalum, niobium, uranium, zirconium, gallium, antimony, bismuth, indium and traces of beryllium. Aluminium can be separated from the first five elements by an extraction in ammoniacal solution containing hydrogen peroxide.Zirconium, gallium, bismuth and antimony can be eliminated by a cupferron extraction and indium by extraction with diethyldithiocarbamate. Beryllium is eliminated by performing an extraction with hydroxyquinoline at pH 5. The proposed method enables a practically specific photometrical determination of aluminium. Applications are given of the determination of trace and higher amounts of aluminium in steels, non-ferrous alloys and in glass.