Determination of Biacetyl by Sensitized Photochemical Kinetic Fluorimetry

Abstract

A new in-situ photochemical kinetic fluorimetric method was proposed for the determination of biacetyl (BI). It is based on the sensitization of BI on the photochemical reaction of amaranth (AM). AM, a nonfluorescent compound was converted into an intensively fluorescent compound in a slightly alkaline medium by the sensitized photochemical reaction, and BI was indirectly determined by monitoring the change of the fluorescence intensity. The determination can be carried out by fixed-time method or tangent method. The kinetic behavior of the reaction and the effects of some experimental conditions were investigated and discussed. The calibration graph was rectilinear from 1.0 μg ml^?1 to 10.0 μg ml^?1 of BI (r = 0.999), the limit of detection was 1.0 ng ml^?1, and the coefficient of variation was 0.44% for 0.90 μg ml^?1 of BI (n = 6). The mechanism for the sensitization of BI was examined and the triplet-triplet energy transfer, in which BI acted as the energy donor and AM as the energy acceptor, was suggested to be the main cause. Its application to real samples has been tested.     

Phosphorescence detection in flowing systems: selective determination of aluminium by flow-injection liquid room-temperature phosphorimetry

The concept of the micelle stabilized liquid room-temperature phosphorescence (MS-LRTP) was applied to the determination of a metal (aluminium) in a flowing system. A three-line flow-injection manifold was developed and various parameters were optimized. A linear calibration graph was obtained for 0–4 μg ml^?1 aluminium. The limit of detection was 50 ng ml^?1 and the relative standard deviations for 0.1 and 1.0 μg ml^?1 aluminium were 2.7 and 1.3% respectively. The proposed procedure is fairly selective. More than 20 common ions studied did not interfere with the determination of aluminium or could be masked by appropriate reagents. The flow-injection method proposed was applied without any preliminary separation to the determination of aluminium in simulated synthetic samples in water and in clinical samples of particular importance in the control of aluminium toxicity in renal failure patients.     

Low-Temperature Phosphorescence Analysis of Mebendazole and Related Imidazoles

Abstract

Native low-temperature phosphorescence of mebendazole and flubendazole in ethanol is used for the determination of these imidazoles in anthelmintic preparations with wavelength maxima and detection limits of λ_EXC = 322 nm, λ_EM = 454 nm; 10 ng ml^?1 and λ_EXC = 325 nm, = λ_EM = 455 nm; 5 ng ml^?1, respectively, with linear response up to 8 μg ml^?1 and 9 μg ml^?1, respectively. The structural basis of these phenomena is discussed for both compounds and for related imidazoles and benzimidazoles. Apart from good sensitivity and excellent specificity offered by the technique, the use of cryogenic equipment (liquid nitrogen, special cuvettes, expensive dewar cells) implies some disadvantages for routine analyses.     

Polarography of disodium pentacyanonitrosylferrate(II): Part 2. Determination at Therapeutic Levels in Serum,Plasma, and Whole Blood

Disodium pentacyanonitrosylferrat(II) (sodium nitroprusside) is determined at therapeutic (ng ml^?1) levels in plasma, serum and blood with conventional and high-performance differential pulse polarography (d.p.p. and h.p.d.p.p.) at a dropping mercury electrode or a static mercury drop electrode. Serum or plasma (3 ml) is treated with perchloric acid containing 1 mg ml^?1 potassium hexacyanoferrate(II), centrifuged for 10 min and subjected to polarography. For spiked serum, calibration graphs are linear over the range 30–1000 ng ml^?1 sodium nitroprusside, regardless of the polarographic technique; the estimated detection limit is 15 ng ml^?1 (5 × 10^?8 M). Calculated therapeutic levels range from 100 to 1000 ng ml^?1. Similar results were obtained for spiked plasma. A similar procedure is suitable for whole blood and was used to study the in-vitro degradation of sodium nitroprusside (200 ng ml^?1) on incubation at 37°C. The in-vitro loss is rapid (t_{$\text{1}\text{2}$} ≈ 6 min) but meaningful in-vivo levels can be obtained when the blood is collected in a 0.9% sodium chloride solution at 0°C. Thiocyanate, the main metabolite of nitroprusside, and thiosulphate, which is a potential antidote for cyanide, do not interfere.     

Phosphorescence and its characteristics in pyridine vapor

The phosphorescence emission of pyridine-d₀ and -d₅ has been observed in the vapor phase by means of time-resolved spectroscopy. The results of the experiments, which are described in full detail in this paper, on the phosphorescence spectrum, the excitation spectrum, the phosphorescence decay and sensitization of biacetyl phosphorescence indicate that the emission concerned is the genuine phosphorescence of the pyridines. For pyridine-d₀ (-d₅), the wavelength of the phosphorescence maximum is 450 nm (440 nm), the phosphorescence quantum yield 1.5 × 10^?6) (1.7 × 10^?6) and the phosphorescence lifetime is 1.2 μs (2.1 μs), the values for pyridine-d₅ being given in parentheses. The phosphorescence characteristics of pyridine are compared with those of other related molecules. The nature of the phosphorescent triplet state of pyridine is discussed with particular regard to the exceptionally fast non-radiative decay from that state.     

Self-quenching and electronic energy transfer of triplet molecules. The benzaldehyde-biacetyl system in the vapor phase

The triplet-triplet energy transfer from benzaldehyde to biacetyl and the competing self-quenching between triplets and ground state molecules of benzaldehyde were investigated in the dilute vapor phase by monitoring the phosphorescence (T₁(nπ^*)S_o) decay of benzaldehyde. Following excitation into the S₁(nπ^*)S₀ absorption band, a triplet self-quenching rate constant of k_SQ=(2.4±0.1) × 10⁴ s^?1 Torr^?1, corresponding to a gas-kinetic cross section of σ_SQ=0.22 A², was measured. The collision-free lifetime of the benzaldehyde triplet was found to be 2.3 ± 0.4 ms. Substitution of the aldehydic proton by deuterium reduces k_SQ by a factor of two: complete deuteration of the molecule has no further effect. Under the same excitation conditions, the energy transfer rate to biacetyl is k_ET=(2.8 ± 0.1) × 10⁶ s^?1 Torr^?1, with σ_ET = 24 A². This process is not influenced by deuteration.     

Inductively-coupled plasma atomic emission spectrometric determination of boron based on generation of methyl borate

Boron is converted to methyl borate, distilled and condensed, and selectively volatilized at 50°C into the plasma without interference from methanol, which quenches the plasma. The 3σ detection limit is 40 ng ml^?1 boron, the calibration graph is linear up to 10 μg ml^?1 and the r.s.d. 3.0% for 2.0 μg ml^?1 (n = 10). Boron is determined in plant-tissue and steel standards.     

Square-wave cathodic adsorptive stripping voltammetric determination of trace amounts of 2-mercaptobenzimidazole in water samples

A sensitive, simple and reproducible square-wave cathodic adsorptive stripping voltammetric method is developed for the determination of 2-mercaptobenzimidazole (MBIM) in different water samples using a static mercury drop electrode (SMDE) as a working electrode. The solution conditions and instrumental parameters were optimized for the determination of MBIM by square-wave cathodic adsorptive stripping voltammetry. This method is based on a sensitive adsorptive reduction peak of the MBIM at ?0.532 V vs. Ag/AgCl reference electrode in a Britton-Robinson buffer at pH 10.0. The linear concentration range was 20–600 ng ml^?1 when using 0.0 V as the accumulation potential. The detection limit of the method was calculated to be 8.41 ng ml^?1. The precision was excellent with relative standard deviations (n = 20) of 2.30%, 1.71%, 2.25% and 1.33% at MBIM concentrations of 40, 90, 200 and 500 ng ml^?1, respectively. The proposed voltammetric method is used for the determination of MBIM in different spiked water samples.     

Indirect determination of fluoride in waters with lanthanum alizarin complexone and inductively-coupled plasma emission spectrometry

Fluoride is determined indirectly by measurement of the La II 333.75-nm line in the lanthanum/alizarin complexone/fluoride complex. The ternary complex is extracted into hexanol containing N,N-diethylaniline and the extract is introduced directly into the plasma. Related to water samples, the detection limit (3σ, concentration factor 5) is 0.59 ng ml^?1 fluoride, calibration is linear up to 1.2 μg ml^?1 and the relative standard deviation for 0.04 μg ml^?1 is 2.6%. Alkali, alkali elements and most anions do not interfere. The method is applied in the analysis of river water, coastal seawater and drinking water.     

Correlation between phosphorescence lifetimes and ratios of steady state phosphorescence to fluorescence intensity for biacetyl in various solvents

The phosphorescence of biacetyl in fluid solutions is quenched not only by oxygen but also by impurities resulting from the distillation procedure and from the freeze-pump-thaw degassing technique. A linear correlation between the measured phosphorescence lifetimes and the ratios of the phosphorescence to the fluorescence intensities is established; the slope affords reliable calculations of the biacetyl triplet lifetimes from steady state measurements and additionally the determination of the rate constant k_p of radiative triplet deactivation. This constant is dependent on the solvent, whereas the fluorescence constant k_F is not.     

Flame atomic absorption spectrometric determination of Cd(II), Ni(II), Co(II) and Cu(II) in tea and water samples after simultaneous preconentration of dithizone loaded on naphthalene

A simultaneous preconcentration procedure for the determination of Cd(II), Ni(II), Co(II) and Cu(II) by atomic absorption spectrometry is described. The method is based on solid phase extraction of the metal ions on dithizone loaded on naphthalene in a mini-column, elution with nitric acid and determination by flame atomic absorption spectrometry. The sorption conditions including NaOH concentration, sample volume and the amount of dithizone were optimized in order to attain the highest sensitivity. The calibration graph was linear in the range of 0.5–75.0 ng ml^?1 for Cd(II), 1.0–150.0 ng ml^?1 for Ni(II), 1.0–150.0 ng ml^?1 for Co(II) and 1.0–125.0 ng ml^?1 for Cu(II) in the initial solution. The limit of detection based on 3S_b was 0.13, 0.32, 0.33 and 0.43 ng ml^?1 for Cd(II), Ni(II), Co(II) and Cu(II), respectively. The relative standard deviations (R.S.D) for ten replicate measurements of 20 ng ml^?1of Cd(II), 100 ng ml^?1 of Ni(II), Co(II) and 75 ng ml^?1 of Cu(II) were 3.46, 2.43, 2.45 and 3.26%, respectively. The method was applied to the determination of Cd(II), Ni(II), Co(II) and Cu(II) in black tea, tap and river water samples.     

Simultaneous determination of copper and lead by graphite-furnace atomic absorption spectrometry after liquid-liquid extraction of the ion pair with zephiramine

A procedure for the simultaneous determination of copper and lead by graphite-furnace atomic absorption spectrometry was investigated by means of a two-channel atomic absorption spectrometer. Both copper(II) and lead(II) are converted into their iodo complex anions and extracted quantitatively into diisobutyl ketone as their ion pairs with tetradecyldimethylbenzylammonium (zephiramine) in a 10-ml centrifuge tube. An aliquot of the organic extract is directly pipetted from the upper layer in the centrifuge tube and injected into the graphite furnace. The detection limits (S/N = 3) are 2.6 ng ml^?1 of copper and 1.0 ng ml^?1 of lead. The relative standard deviations for 10 replicate determinations are 2.9% for 20 ng ml^?1 of copper and 2.7% for 10 ng ml^?1 of lead. Results of analyses of some practical samples are given.     

反相胶束介质中敏化双乙酰室温磷光——-α-萘乙酸为敏化剂

本文报道了AOT-C6H12-H2O反相胶束介质中α-萘乙酸(α-NAA)敏化双乙酰(BIAC)的室温磷光。详细讨论了琥珀酸二(2-乙基己基)酯磺酸钠(AOT)浓度和水泡大小(W值)对敏化磷光的影响。吸收、发光性质和微粘度性质的实验表明AOT浓度对敏化磷光强度的影响由敏化磷光寿命、能量转移效率和Poisson分布决定; 一定范围内, 随着水浓度增大, 由于粘度下降和内腔半径增大作用的相互抵销, 水泡大小仅有微弱影响。当W([H2O]/[AOT])大于20后, 内腔半径增大起主要作用, 敏化磷光强度快速下降。与普通SDS胶束相比, 磷光强度约增强13倍, 检出限约下降一个数量级。建立了灵敏的测定α-萘乙酸和双乙酰的敏化室温磷光法, 检出限分别达2.0×10^-^8mol.dm^-^3(α-NAA)和8.5×10^-^9mol.dm^-^3(BIAC)。     

一种新的敏化/猝灭室温磷光: CTAB胶束中α-溴代萘敏化联乙酰的室温磷光猝灭

本文首次报道了将敏化和猝灭同时偶合在同一体系中的敏化/猝灭室温磷光新方法。体系中, CTAB胶束一方面增强α-溴代萘的室温磷光发射、α-溴代萘和联乙酰的三重态-三重态能量转移效率, 另一方面起到猝灭α-溴代萘敏化联乙酰发射的室温磷光的作用。CTAB对联乙酰的猝灭反应由三重态-三重态能量转移速率限制,求得α-溴代萘敏化联乙酰的三重态-三重态能量转移速率常数为1.76×10^9(mol.dm^-^3)^-^1s^-^1, CTAB对联乙酰的猝灭常数为7.82×10^7(mol.dm^-^3)^-^1s^-^1。详细研究了实验条件, 实现了猝灭法测定联乙酰,检测限达2.8×10^-^8mol.dm^-^3。     

Voltammetric behaviour of ascorbic acid at a graphite—epoxy composite electrode chemically modified with cobalt phthalocyanine and its amperometric determination in multivitamin preparations

Cyclic voltammetry was used to investigate the electrochemical behaviour of ascorbic acid at a carbon—epoxy composite electrode modified with the electron mediator cobalt phthalocyanine. The modified electrode reduced the overpotential necessary for the oxidation of the vitamin by approximately 150 mV to 0.21 V vs. The saturated calomel electrode; the process was dependent on the pH of the supporting electrolyte, but independent of ionic strength over the range studied. The relative standard deviation (r.s.d.) of the peak heights of the cyclic voltammograms was 0.81% for a 1 × 10^?4 M ascorbic acid solution (n = 7). The optimum supporting electrolyte was found to be 0.05 M phosphate buffer (pH 5).Amperometry in stirred solutions was then done at an applied potential of +0.25 V. The limit of detection was 0.65 ng ml^?1 and the calibration graph was linear in the range 175 ng ml^?1?50 μg ml^?1. The method was used to determine ascorbic acid concentrations in single- and multivitamin preparations; the recovery was 97.86% for the vitamin added to one preparation. The r.s.d. for the analyses in these samples was about 5%. For comparison, the vitamin was also determined in these tablets using LC with UV detection at 254 nm; the correlation coefficient for the levels determined was 0.9989 (p = 0.0007).     

Determination of Morestan Residues in Water and Foodstuffs by Transmitted Room Temperature Solid Phase Spectrophosphorimetry

Abstract

A method for the determination of the pesticide morestan by means of transmitted room temperature solid phase spectrophosphorimetry has been developed. The method is based on the native phosphorescence showed by the morestan when it is fixed in a Whatman No 4 paper as a solid support. The excitation and emission wavelengths were 362 and 527 nm, respectively. The optimum phosphorescent emission was obtained when the delay time was 0.15 ms and the gate time 12.0 ms without need of a heavy atom. The linear dynamic range was between 0.1 and 1.0 μg.ml^?1, and the detection and quantification limits were 0.03 and 0.09 μg.ml^?1, respectively. The precision of the method, expressed as the relative standard deviation of ten samples at the 0.6 μg.ml^?1 concentration level, was 3.0%. The method was applied to the determination of the pesticide in different type of waters, potatoes and vegetables.     

Kinetic Spectrophotometric Determination of Vanadium (V) Based on its Inhibitory Effect on the Thionine – Ascorbic Acid Reaction

ABSTRACT

A simple and sensitive kinetic method for the determination of vanadium(V) based on its inhibitory effect on the reduction of thionine by ascorbic acid at pH=5 is described. The reaction rate is monitored spectrophotometrically by measuring the decrease in absorbance of thionine at 598 nm after a fixed time (10 min). The calibration graph is linear in the range of 10 ? 120 ng ml^?1 of vanadium(V) and the detection limit is 6 ng ml^?1. The relative standard deviation (RSD) for 80 ng ml^?1 of V(V) was 0.96% (n=10). The method was successfully applied to the determination of vanadium in a certified reference sample.     

Quenching of the lowest benzene triplet state in the vapor phase by nitric oxide

the rate constant for quenching of the triplet state (³B_1u) of benzene vapor by nitric oxide has been determined from a study of the flash photosensitization of biacetyl phosphorescence. The rate constant has been found to be (1.08 ± 0.2) × 10^?11 cm³ molecule^?1 sec^?1. Although this value is much larger than expected, it is in agreement with rate constants reported for quenching of some liquid phase aromatics.     

Determination of caprolactam by adsorptive voltammetry after separation by thin-layer chromatography

Caprolactam (2-oxohexamethyleneimine) can be determined in wastewaters and natural waters by adsorptive stripping voltammetry after separation of the product of the reaction between caprolactam and p-(N,N-dimethylamino)benzene-p′-azobenzoyl chloride. When a hanging mercury drop electrode is used with an accumulation time of 60 s in stirred solution, caprolactam can be determined from a lower limit of 0.2 μg ml^?1. With a 360-s accumulation time, linear calibration plots are obtained for 8 × 10^?10?8 × 10^?9 mol l^?1 caprolactam. The effect of interfering sample components is eliminated by the TLC separation.     

Determination of trace amounts of nickel by differential pulse adsorptive cathodic stripping voltammetry using calconcarboxylic acid as a chelating agent

A method for the determination of nickel(II) by stripping voltammetry is described. The method is based on the adsorptive accumulation of nickel(II) calconcarboxylic acid complex onto a hanging mercury drop electrode (HMDE), followed by the reduction of the adsorbed complex using differential pulse voltammetry. The optimum operating conditions and parameters were found to be 0.05 M NH₃/NH₄Cl buffer (pH = 9.5) as the supporting electrolyte, a ligand concentration of 1 × 10^?6 M, accumulation potential of ?0.5 V (vs. Ag/AgCl) and accumulation time of 60 s. At the optimized conditions, the peak current is proportional to the concentration of nickel in the range of 1.7 × 10^?9 to 4.7 × 10^?7 M (0.1–28 ng ml^?1) with a detection limit of 0.05 ng ml^?1. The relative standard deviation (n = 10) at nickel concentrations of 2, 10 and 15 ng ml^?1 varies in the range 0.76 to 2.1%. Possible interferences by metal ions, which are of great significance in real matrices, have been studied. The method was successfully applied to the determination of nickel content in a chocolate sample.