FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.     

Preparation of ethyl levulinate from wheat stalk over Zr(SO4)2/SiO2

A series of Zr(SO₄)₂/SiO₂ solid acid catalysts with different Zr(SO₄)₂ loadings were prepared by water-soluble-impregnation method at room temperature. Then, the prepared catalysts were characterized by Fourier transform infrared spectroscopy, transmission electron microscopy and energy-dispersive X-ray spectrum, X-ray diffraction, adsorption/desorption of N₂, and temperature-programmed desorption of NH₃. The results showed that the active component Zr(SO₄)₂ was successfully adhered to the mesoporous SiO₂, and the acid amount of Zr(SO₄)₂/SiO₂ increased with the increasing of the Zr(SO₄)₂ loadings. Finally, the wheat stalk was used as raw material and depolymerized over Zr(SO₄)₂/SiO₂ to produce ethyl levulinate (EL). The reaction mixture was separated and purified by filtration and vacuum distillation. The kinetic characteristics and the reaction pathway were also studied. A comparative study showed that 20 wt.% Zr(SO₄)₂/SiO₂ exhibited higher catalytic activity. When reaction temperature, time, catalyst dosage and Zr(SO₄)₂ loadings were 190 °C, 50 min, 20 wt.% and 30 wt.%, the EL yield reached a maximum of 17.14%. The relative content of EL exceeded 90% after three steps of distillation.     

Synthesis, characterization and hydrogen storage capacity of MS2 (M = Mo, Ti) nanotubes

The structure, morphology and hydrogen-storage capacity of MS₂ (M = Mo, Ti) nanotubes prepared by different experimental methods were studied. It was found that the MoS₂ nanotubes treated by KOH displayed the gaseous storage capacity of 1.2 wt% hydrogen (under the hydrogen pressure of 3 MPa and 25°C) and the electrochemical discharge capacity of 262 mAh/g (at the discharge current density of 50 mA/g and 25°C) that corresponds to about 1.0 wt % hydrogen. In comparison, TiS₂ nanotubes can store 2.5 wt% hydrogen under the hydrogen pressure of 4 MPa and 25°C. The results show that MS₂ compound nanotubes are promising materials for hydrogen storage. __________ Translated from Acta Scientiarum Naturalium Universitatis Nankaiensis, 2005, 38(4) (in Chinese)     

Syntheses of MO2 (M=Si, Ce, Sn) nanoparticles by solid-state reactions at ambient temperature

Nano oxides (SiO₂, CeO₂, SnO₂) were successfully synthesized by solid-state reactions at ambient temperature. The nanoparticles were characterized by X-ray powder diffraction, TEM, BET, and TGA-DTA. The SiO₂ particles were also investigated using IR spectra. Effects of calcination on the nanoparticles were studied in this paper. The solid-state reaction technique is a convenient, inexpensive and an effective preparation method of monodisperse oxide nanoparticles in high yield. The mechanisms of the formation of nano materials by solid-state reactions at ambient temperature were primarily investigated.     

Preparation and Characterization of SiO2-MxOy(M = V, Sn, Sb) Thin Films from Silicic Acid and Metal Chlorides

The preparation of SiO₂-M _x O _y (M = V, Sn, Sb) binary oxide thin films by sol-gel method was investigated. The reaction of silicic acid with metal chloride (M = Sn and Sb) or oxychloride (M = V) formed homogeneous solutions. The dip-coating of slide glass and silicon wafer followed by heat treatment gave oxide films having Si—O—M bond. The changes of FT-IR spectra as a function of heat treatment temperature and molar composition confirmed the Si—O—M bonds. The sheet resistance of films increased with an increase on heat treatment temperature and decrease in the content of metal oxide M _x O _y . X-ray diffraction peaks were observed for the SiO₂-V₂O₅ films with high V₂O₅ contents and heat-treated above 250°C, while the others were amorphous. Oxide films heat treated at 500°C had a thickness between 340–470 nm.     

Microporous Silica Xerogel Membrane with High Selectivity and High Permeance for Carbon Dioxide Separation

The asymmetric microporous silica xerogel membrane was prepared by sol-gel method. A multi-layer (asymmetric) structure was obtained by silica xerogel layer on top of mesoporous silica layer (mean pore diameter of 4 nm), supported by porous alumina tube (mean pore diameter of 0.1 m). The ratio of the permeances, CO₂/N₂ for this membrane attained more than 60 at 298 K. This value is considerably higher than the theoretical Knudsen value (CO₂/N₂ = 0.8). The gas permeances of this membrane were about 5–10 times higher than the previous membrane. Application of the membrane to an enrichment of CO₂ from air was also investigated. CO₂ in the air (about 300 ppm) was concentrated to more than 1000 ppm by using the membrane at 298 K.     

O MAS NMR study of the oxygen local environments in the anionic conductors Y2(B1−xB′x)2O7(B, B′=Sn, Ti, Zr)

The local environments for oxygen in yttrium-containing pyrochlores and fluorites, Y₂(B_1−xB′_x)₂O₇ (B=Ti, B′=Sn, Zr) are investigated by using solid state ¹⁷O MAS NMR spectroscopy. The quadrupolar coupling constants of the nucleus, ¹⁷O are sufficiently small for these ionic oxides, that high-resolution spectra are obtained from the MAS spectra. Different oxygen NMR resonances are observed due to local environments with differing numbers of metal cations (Y³⁺, Sn⁴⁺, Ti⁴⁺ and Zr⁴⁺), allowing the numbers of different local environments to be quantified and cation mixing to be investigated. Evidence for pyrochlore-like local ordering is detected for Y₂Zr₂O₇, which nominally adopts the fluorite structure.     

正极材料Li(Ni0.5Mn0.5)1-xMxO2 (M=Ti，Al；x=0，0.02)电化学行为的比较研究

0IntroductionMany efforts have been made to develop newmaterials as an alternative to LiCoO2due to the rela-tively high cost and toxicity of Co.Much attention hasbeen paid to layered structure cathode materials suchas LiMnO2and LiNiO2due to their lower co…     

Gram-Scale Synthesis of an Ultrastable Microporous Metal-Organic Framework for Efficient Adsorptive Separation of C2H2/CO2 and C2H2/CH4

A highly water and thermally stable metal-organic framework (MOF) Zn₂(Pydc)(Ata)₂ (1, H₂Pydc = 3,5-pyridinedicarboxylic acid; HAta = 3-amino-1,2,4-triazole) was synthesized on a large scale using inexpensive commercially available ligands for efficient separation of C₂H₂ from CH₄ and CO₂. Compound 1 could take up 47.2 mL/g of C₂H₂ under ambient conditions but only 33.0 mL/g of CO₂ and 19.1 mL/g of CH₄. The calculated ideal absorbed solution theory (IAST) selectivities for equimolar C₂H₂/CO₂ and C₂H₂/CH₄ were 5.1 and 21.5, respectively, comparable to those many popular MOFs. The Q_st values for C₂H₂, CO₂, and CH₄ at a near-zero loading in 1 were 43.1, 32.1, and 22.5 kJ mol⁻¹, respectively. The practical separation performance for C₂H₂/CO₂ mixtures was further confirmed by column breakthrough experiments.     

Rationally Designed Bi2M2O9 (M = Mo/W) Photocatalysts with Significantly Enhanced Photocatalytic Activity

Novel Bi₂W₂O₉ and Bi₂Mo₂O₉ with irregular polyhedron structure were successfully synthesized by a hydrothermal method. Compared to ordinary Bi₂WO₆ and Bi₂MoO₆, the modified structure of Bi₂W₂O₉ and Bi₂Mo₂O₉ were observed, which led to an enhancement of photocatalytic performance. To investigate the possible mechanism of enhancing photocatalytic efficiency, the crystal structure, morphology, elemental composition, and optical properties of Bi₂WO₆, Bi₂MO₆, Bi₂W₂O₉, and Bi₂Mo₂O₉ were examined. UV-Vis diffuse reflectance spectroscopy revealed the visible-light absorption ability of Bi₂WO₆, Bi₂MO₆, Bi₂W₂O₉, and Bi₂Mo₂O₉. Photoluminescence (PL) and photocurrent indicated that Bi₂W₂O₉ and Bi₂Mo₂O₉ pose an enhanced ability of photogenerated electron–hole pairs separation. Radical trapping experiments revealed that photogenerated holes and superoxide radicals were the main active species. It can be conjectured that the promoted photocatalytic performance related to the modified structure, and a possible mechanism was discussed in detail.     

Electronic structure of X2 Y3 molecules (X = B, Al, Ga; Y = O,S): A theoretical study

Ab initio molecular orbital and density functional theory calculations on X₂Y₃ (X = B, Al,Ga; Y = O,S) indicate a bent structure withC _2v symmetry to be the preferred arrangement for B₂ O₃, B₂ S₃ and Al₂S₃. In contrast, the linear isomer is favoured for Al₂ O₃ and Ga₂ O₃. These are in agreement with the experimentally observed structures. The electronegativity difference between X and Y, the MO patterns and the ionic nature of the bonding explain variations in the molecular structure. The results from the two theoretical approaches (MP2/6-31G* and Becke3LYP/6-311 +G* level) are comparable.     

A parametric study of CO2/N2 gas separation membrane processes for post-combustion capture

Capture of CO₂ from flue gases produced by the combustion of fossil fuels and biomass in air is referred to as post-combustion capture. Chemisorbent processes are considered to be the most feasible method and are already at an advanced stage of development, but gas separation membranes are attracting more and more attention as a possible alternative. This paper describes a detailed parametric study of mass and energy balances for a simulated single membrane process. Typical operating conditions (CO₂ concentration in the flue gas, pressure and temperature, etc.) together with the influence of the membrane quality (permeability, selectivity) and membrane area on membrane performance (CO₂ separation degree and CO₂ purity) are simulated over a wide range of parameters.     

S-M（M=Al,Co）复合掺杂LiMn2O4的结构稳定性

应用量子化学电荷自洽离散变分Xα(SCC-DV-Xα)方法,研究了S-Al、S-Co复合掺杂增强尖晶石结构锂锰氧化物稳定性的作用机制.计算结果表明, S-Al复合掺杂锂锰尖晶石和S-Co复合掺杂锂锰尖晶石中的共价键强度均比未掺杂尖晶石LiMn2O4中的强,且与MnO2中的共价键强度相近; S-Al, S-Co复合掺杂尖晶石中Mn的电荷也与MnO2模型[Mn6O26]28－中十分接近. Mn原子的电荷密度次序是MnO2≈掺硫铝后锰锂尖晶石≈掺硫钴后的锂锰尖晶石< 锰锂尖晶石.即[LixMn3Co3O20S6]n－和[LixMn3Al3O20S6]n－中Mn的状态与MnO2中的Mn相似.上述结果揭示了S和非Jahn-Teller效应阳离子（Al3＋,Co3＋）复合掺杂尖晶石结构锂锰氧化物在电化学过程中不会发生Jahn-Teller畸变的内在原因.     

Application of manganese (II) phthalocyanine synthesized in situ in the SiO2/SnO2 mixed oxide matrix for determination of dissolved oxygen by electrochemical techniques

This work describes the in situ immobilization of Mn(II) phthalocyanine (MnPc) in a porous SiO₂/SnO₂ mixed oxide matrix obtained by the sol gel processing method. The chemically modified matrix SiO₂/SnO₂/MnPc, possessing an estimated amount of 8 × 10⁻¹⁰ mol cm⁻² of MnPc on the surface, was used to prepare an electrode to analyze dissolved oxygen in water by an electrochemical technique. The electrode was prepared by mixing the material with ultrapure graphite and evaluated using differential pulse voltammetry. Dissolved O₂ was reduced at −0.31 V with a limit of detection (LOD) equal to 7.0 × 10⁻⁴ mmol L⁻¹. A mechanism involving four electrons in O₂ reduction was determined by the rotating disk electrode technique.     

An Efficient Procedure for the Synthesis of Benzoxazole and Benzothiazole Derivatives Using a H2O2/SiO2-FeCl3 System

A series of benzoxazole and benzothiazoles was readily prepared from the reaction of ortho-aminophenol/ortho-aminothiophenol and aldehydes using solid silica supported ferric chloride (SiO₂-FeCl₃) as catalyst followed by oxidation with H₂O₂ under ambient conditions. Some of advantages of this method are a simple and convenient procedure, easy purification, and shorter reaction times.

Supplemental materials are available for this article. Go to the publisher's online edition of Phosphorus, Sulfur, and Silicon and the Related Elements to view the free supplemental file.     

Vibrational spectra of cyclooctatetraenyl alkali metal complexes [C8H8M2 (M = Na, K)]: A theoretical study

The cyclooctatetraenyl dianion (C₈H₈²⁻) π-conjugated system forms a stable complex system with alkali and some transition metals. The results of vibrational analysis for C₈H₈M₂ (M = Na, K) complexes were reported here. The geometries of C₈H₈M₂ (M = Na, K) were optimized using ab initio (HF, MP2, CCSD(T)) and DFT (B3LYP) methods with 6-311G** and 6-311++G** basis sets and the harmonic frequencies were obtained. To reproduce and compare with the experimental values the structurally similar molecules C₅H₅M (M = Na, K) and benzene were studied. The scale factors obtained from these systems were applied to predict the experimental frequencies of C₈H₈M₂ (M = Na, K). The force field and vibrational spectra are analyzed and the most probable assignments are proposed for all the fundamentals based on the potential energy distribution.     

Novel M(II)–Hg(II) coordination polymers generated from metal-containing building blocks M(2-pyrazinecarboxylate)2 · (H2O)2 (M=Cu, Ni, Co) and HgCl2

A new class of M(II)–Hg(II) (M=Cu(II), Co(II), Ni(II)) mixed-metal coordination polymers, Cu(2-pyrazinecarboxylate)₂HgCl₂ (4), [Co(2-pyrazinecarboxylate)₂(HgCl₂)₂] · 0.61H₂O (5) and [Ni(2-pyrazinecarboxylate)₂(HgCl₂)₂] · 0.77H₂O (6), have been prepared by self assembly of metal-containing building blocks, M(2-pyrazinecarboxylate)₂ · (H₂O)₂(M=Cu(II), Co(II), Ni(II)), with HgCl₂. Compounds 4–6 were characterized fully by IR, elemental analysis and single crystal X-ray diffraction. Compound 4 crystallized in the monoclinic space group C2/c, with a=17.916(5) Å, b=7.223(2) Å, c=13.335(4) Å, β=128.726(3)°, V=1346.2(6) ų, Z=4. It contains alternating Hg(II) and Cu(II) metal centers that are cross-linked by 2-pyrazinecarboxylate spacers and chlorine co-ligands to generate a unique three-dimensional Hg(II)–Cu(II) mixed metal framework. Compound 5 crystallized in the triclinic space group P , with a=6.3879(7) Å, b=6.6626(8) Å, c=13.2286(15) Å, α=96.339(2)°, β=91.590(2)°, γ=113.462(2)°, V=511.71(10) ų, Z=1. Compound 6 also crystallized in the triclinic space group P , with a=6.3543(8) Å, b=6.6194(8) Å, c=13.2801(16) Å, α=96.449(2)°, β=92.263(2)°, γ=113.541(2)°, V=506.67(11) ų, Z=1. Compounds 5 and 6 are isostructural and in the solid state the Hg(II)M(II)Hg(II) units are connected by Hg₂Cl₂ linkages to produce a novel M(II)–Hg(II) (M=Co(II), Ni(II)) zigzag mixed-metal chain, in which a new type of M–M′–M′–M array was observed. The metal containing building blocks, M(2-pyrazinecarboxylate)₂ · (H₂O)₂ (M=Cu(II), Co(II), Ni(II)), exhibit different connectivities to HgCl₂ depending on the metal cation contained within them.     

二氯二茂钛(锆)/格氏试剂体系在有机合成中的应用

介绍近几年来二氯二茂钛 (锆 ) /格氏试剂体系在有机合成中的应用 ,特别是使用该体系发展的新反应及其机理的研究情况     

Silica supported orthophosphoric acid (H3PO4. SiO2): a green,heterogeneous catalyst for solvent-free oxathioacetalization of aldehydes

Abstract

A silica supported orthophosphoric acid catalyst (H₃PO₄. SiO₂) was prepared by stirring silica gel (100–200mesh) with orthophosphoric acid in chloroform at room temperature. The catalyst was characterized by scanning electron microscopy (SEM) and energy dispersion analytical X-ray (EDX). It demonstrated excellent activity, chemoselectivity, and recyclability for oxathioacetalization of aldehydes.     

Syntheses and characterization of two oxoborates, (Pb3O)2(BO3)2MO4 (M=Cr, Mo)

Two oxoborates, (Pb₃O)₂(BO₃)₂MO₄ (M=Cr, Mo), have been prepared by solid-state reactions below 700 °C. Single-crystal XRD analyses showed that the Cr compound crystallizes in the orthorhombic group Pnma with a=6.4160(13) Å, b=11.635(2) Å, c=18.164(4) Å, Z=4 and the Mo analog in the group Cmcm with a=18.446(4) Å, b=6.3557(13) Å, c=11.657(2) Å, Z=4. Both compounds are characterized by one-dimensional chains formed by corner-sharing OPb₄ tetrahedra. BO₃ and CrO₄ (MoO₄) groups are located around the chains to hold them together via Pb–O bonds. The IR spectra further confirmed the presence of BO₃ groups in both structures and UV–vis diffuse reflectance spectra showed band gaps of about 1.8 and 2.9 eV for the Cr and Mo compounds, respectively. Band structure calculations indicated that (Pb₃O)₂(BO₃)₂MoO₄ is a direct semiconductor with the calculated energy gap of about 2.4 eV.