热处理对化学沉积Ni-Fe-P合金性能的影响

采用DSC和XRD研究了化学镀Ni-Fe-P合金的晶化行为和结构.结果表明,镀态合金呈非晶结构, 367.6 ℃下热处理出现亚稳态Ni5P2(P3)和Fe-Ni(Im3m), 499.2 ℃下热处理进一步晶化为稳定的Ni3P(I-4)和FeNi3(Pm3m).采用磁性能实验和在w=3.5％氯化钠溶液浸泡实验以及阳极极化实验研究了热处理对镀层磁性能和耐腐蚀性的影响.结果表明,该镀层在镀态时几乎没有磁性,随着退火温度的升高,磁性能不断提高. 400 ℃以后,镀层的饱和磁化强度和矫顽力随着退火温度升高而急剧上升.浸泡实验和阳极极化实验结果均表明镀态镀层比经热处理后的镀层在w=3.5％氯化钠溶液中具有更好的耐腐蚀性,但是它们的阳极极化行为不同.     

退火前后镍钨硼合金电沉积层的结构与性能

采用电化学技术、XPS、DSC、XRD等方法研究Ni W B合金电沉积及热处理前后合金镀层的结构和显微硬度.结果表明,在Ni W B合金电沉积过程中伴随着化学沉积镍等过程以及Na2B4O7在镀层中的夹杂;Ni W和Ni W B合金电沉积层分别表现为纳米晶结构和非晶态结构;热处理过程中合金电沉积层发生晶粒粗化过程以及Ni W B合金镀层发生新相形成过程,产生Ni4W和镍硼化物如Ni2B、Ni3B等沉淀物;400 ℃热处理2 h后Ni W合金镀层有最大的显微硬度达919.8 kg•mm－2,而在500 ℃下Ni W B合金有最大的硬度达1132.2 kg•mm－2.     

Synthesis and Soft Magnetic Properties of Mg-doped Ni Nanoparticles

Mg-doped Ni nanoparticles with good soft magnetic properties were prepared with the sol-gel method and were sintered at 400, 500, 600, and 900℃ in argon atmosphere, respectively. The structure and magnetic properties of the samples were studied by means of X-ray diffraction, TEM, and VSM magnetometers. X-Ray powder diffraction results show that Ni-Mg solid solution was formed with the single phase of face-centered cubic（fcc） structure. The particle size became larger with the increase of temperature. When the sintering temperature was 400 °C, the particle size was 6.3 nm, whereas it was 46.2 nm at 900 °C. Both the saturation magnetization（Ms） and the coercivity were enhanced with the increase of the particle size. The Ms values of the samples ranged from 18.965 to 46.766 emu/g and the coercivity ranged from 1051.3568 to 9145.0848 A/m.     

镍镀层中微量六方晶格镍的存在与稳定性研究

对由含糖精的Watts液得到的镍镀层(含硫镍)和Watts镍镀层(无硫镍)进行透射电镜观察及选区电子衍射实验,结果表明无硫镍镀层呈粒状结构,晶粒尺寸在100～500nm之间,属面心立方结构；含硫镍镀层为层状结构,层间距在700～1500nm之间,每层又由许多宽约200～300nm的小层组成,晶粒尺寸约20～30nm,大部分属面心立方结构,在层与层交界处发现有少量六方结构镍晶体,差示扫描量热法实验表明,在约180℃左右六方结构镍转化为更稳定的面心立方结构。     

电沉积Ni81.32Mo18.68非晶/纳米晶镀层的晶化动力学

在碱式碳酸镍为主的盐溶液中用电沉积法制备出含Mo原子分数为18.68%的Ni-Mo合金镀层. X射线衍射(XRD)表明该镀层为非晶/纳米晶混合结构; 用差示扫描量热法(DSC)对这种非晶/纳米晶混合结构的合金进行了晶化动力学研究, 测得其晶化激活能(E)为3.84×105 kJ·mol-1; 晶化开始温度约为440 ℃, 与非晶态结构Ni-Mo合金镀层相比, 晶化温度提高了约13 ℃. 热处理过程发现, 非晶/纳米晶混合结构镀层中少量纳米晶的存在阻止了非晶态相转变的可能性, 提高了混合结构镀层的热稳定性和晶化温度; 镀层在450 ℃热处理过程中有新相产生, 其不仅提高了镀层的密实度, 同时也阻止了非晶态相的转变, 提高了镀层的热稳定性.     

Electrodeposition, Structure and Corrosion Resistance of Nanocrystalline Ni-W Alloy

Ni—W alloy was electrodeposited from the electrolyte solution containing sodium tungstate, nickel sulfate and ammonium citrate. The electrodeposition, heat treatment, structure, surface morphology and corrosion resistance in w=0.03 NaCl solution, of Ni-W alloys were studied by means of DSC, XRD, SEM and electrochemical techniques. The results showed that the obtained Ni-W alloy electrodeposit with W weight content (Ww=0.471) was presented in more typical nanocrystaUine, After heat treatment at 400 ℃ for 1 h, the phase structure of the deposits was not obviously changed whereas the agglomerate for the reunion of tiny grains on deposit surface caused the granule in a more smooth morphology, the microhardness was slightly increased and the corrosion resistance was enhanced.     

NiB和NiP超细非晶合金的退火晶化行为及催化性能

 采用X射线吸收精细结构（XAFS）,X射线衍射（XRD）和差热分析（DTA）等方法研究了以化学还原法制备的NiB和NiP超细非晶态合金催化剂在退火过程中的结构变化．XRD结果表明,在300℃下退火时,NiB超细非晶态合金晶化生成纳米晶Ni3B亚稳物相,NiP超细非晶态合金则主要晶化生成金属Ni和部分晶态Ni3P的混合物相;在500℃退火且近于完全晶化的条件下,大部分超细非晶态合金都晶化为金属Ni．XAFS结果定量地说明,对于NiB和NiP初始样品,第一近邻Ni－Ni配位的平均键长Rj分别为0.274和0.271nm,其结构无序度σS很大,分别为0.033和0.028nm,其热无序度σT分别为0.0069和0.0060nm．300℃退火后,晶化生成的Ni3B的Ni－Ni配位的σS降低到初始样品的33％,仅为0.011nm．500℃退火后,NiB样品的结构参数与金属Ni基本一致,但NiP样品的Ni－Ni配位的σS还远大于σT,仍为0.0125nm,表明NiB和NiP超细非晶态合金的退火晶化行为有很大的差别．纳米晶Ni3B催化苯加氢反应的转化率比超细Ni－B非晶态合金或多晶金属Ni更高,表明纳米晶Ni3B中的Ni与B原子组成了苯加氢催化反应的活性中心．     

Ni/HZSM-5催化剂的结构及其催化山梨醇水相加氢合成烷烃性能

采用浸渍法制备了Ni/HZSM-5双功能催化剂,考察了焙烧温度对催化剂结构及其催化山梨醇水相加氢合成C5～C6烷烃性能的影响.结果表明,在金属中心和酸性载体的协同作用下,通过山梨醇中C-O键加氢和异构化高选择性合成了C5～C6烷烃.经500°C焙烧的Ni/HZSM-5催化剂上山梨醇水相加氢的活性最高,山梨醇转化率为62.0%,戊烷和己烷的总选择性为76.4%,其中异己烷选择性达45.4%.对催化剂进行N2物理吸附、X射线衍射、NH3程序升温脱附和H2程序升温还原等表征后发现,经500°C焙烧催化剂的有效比表面积和孔体积均明显增大,HZSM-5负载的硝酸镍分解成较小晶粒的NiO,表面酸量适中,且Ni物种与载体相互作用较强,较易被H2还原,Ni还原度达100%.这是其催化活性最高的原因.     

Formation of nanocrystals in the ZrO<Subscript>2</Subscript>–H<Subscript>2</Subscript>O system

Formation of zirconia nanocrystals in the course of thermal treatment of an X-ray amorphous zirconium oxyhydroxide was studied. It was shown that the formation of tetragonal and monoclinic polymorphs of ZrO₂ in the temperature range from 500 to 700°C occurs owing to dehydration and crystallization of amorphous hydroxide. An increase of the temperature up to 800°C and higher activates mass transfer processes and, as a result, activates the nanoparticle growth and increases the fraction of the phase based on monoclinic modification of ZrO₂ due to mass transfer from the nanoparticles with the non-equilibrium tetragonal structure. Herewith, formed ZrO₂ nanocrystals with monoclinic structure have a broad size distribution of crystallites, and the average crystallite size after thermal treatment at 1200°C for 20 min is about 42 nm.     

PdNiO/C在碱性介质中对甲醇的电氧化

应用循环伏安,计时电流,计时电位和XRD等方法研究了碱性介质中甲醇在自制PdNiO/C和Pd/C催化剂上的电化学氧化以及高温热处理对催化剂结构和性能的影响.结果表明,还原温度为70℃,Pd、Ni原子比为8∶2时,PdNiO/C催化剂对甲醇电化学氧化具有较好的催化活性.热处理可增大催化剂粒径,升高结晶度,降低分散度和催化活性,并且可使NiO从Pd的晶格中脱离出来.与Pd/C催化剂相比,优选的PdNiO/C催化剂有更高的催化活性和更好的抗毒化能力.     

钕掺杂磷酸盐微晶玻璃的制备及表征

利用熔融和晶化技术制备掺钕磷酸盐玻璃陶瓷。 采用差热分析、X射线衍射、扫描电子显微镜、紫外 可见 近红外分光光度计及荧光光谱仪对材料进行表征和分析。 结果表明,在490～540 ℃核化1～2 h,在550 ℃晶化1～3 h,可制得主晶相为Al2SiO5的透明玻璃陶瓷。 其透过率可达69%,晶粒平均尺寸为90 nm,并随热处理时间的增加逐渐增大,但透过率降低。 由于Nd3+在热处理后进入到Al2SiO5晶相中,使荧光谱线在1 056 nm处峰值比原始玻璃强度大。     

聚醚酮酮的合成、表征与结晶行为

聚醚酮酮的合成、表征与结晶行为＊王军佐郑玉斌柯扬船于冬宏＊＊吴忠文（吉林大学化学系长春１３００２３）关键词聚醚酮酮，结晶结构，低温熔融峰，热处理聚醚醚酮８０年代初由英国ＩＣＩ公司商品化，由于其优异的性能，已在宇航、军工、核能等领域得到了广泛的应用，聚...     

γ′-Fe_4N纳米晶薄膜的磁性及热稳定性研究

采用直流磁控溅射方法,在Si(100)单晶衬底上获得了γ′-Fe4N纳米晶薄膜样品.将样品在真空中分别于300,400,500,600,700和800℃下进行热处理,利用XRD,SEM和VSM等测试手段对样品的结构、形貌和磁性进行表征.结果表明,热处理温度在300～500℃时,在γ′-Fe4N纳米晶粒的界面处形成了Fe8N包裹层,600℃时,Fe8N包裹层转变为α-Fe,当热处理温度≥700℃时,样品全部转变为α-Fe.γ′-Fe4N薄膜样品在600℃以下温度热处理可保持其主相γ′-Fe4N的结构稳定,而其软磁性能并未发生明显的减弱.     

Ni2P/HZSM5上噻吩加氢脱硫性能研究

采用程序升温还原方法制备了Ni2P/HZSM5催化剂。用X射线衍射 (XRD)、低温N2吸附（BET）、扫描电镜(SEM)等技术对催化剂样品的物相、比表面积、形貌等性质进行了表征。在连续微反系统中测定了Ni2P/HZSM5催化剂对噻吩加氢脱硫催化活性；研究了Ni2P负载量、前驱体中Ni/P摩尔比对催化剂的物相及性能的影响，考察了空速、反应温度、反应压力等操作条件对催化剂上噻吩加氢脱硫性能的影响。实验结果表明，Ni2P/HZSM5催化剂对噻吩加氢脱硫反应具有较高的活性和稳定性。随着Ni2P负载量、前驱体中Ni/P摩尔比的增加，催化剂的活性和稳定性先升高后降低。反应温度和体积空速对Ni2P/HZSM5催化剂的噻吩加氢脱硫性能有较明显的影响，反应压力和进料氢油比的影响相对较小。     

Thermal analysis and thermochemistry of vitreous into crystalline state transition

Thermochemistry and structural mechanism of crystallization of MgO-Al₂O₃-SiO₂ glasses with TiO₂ as crystallization activator were studied. Thermal and HREM investigation proved that near the T _g temperature crystallization is going by rearrangement of glass structure elements and part of its components redistribution like at disorder — order phase transition in solid bodies. Nanocrystals of Mg-titanate and high quartz structure solid solution are formed then. Next enstatite and cordierite are crystallizing. Thermochemical and chemical bonds strength analysis indicate that during multistage crystallization of glasses, kind and order of crystal phase formation, is determined by the glass structure decomposition progress and its particular components release accompanying increase of temperature. It has been proved that molar heat capacity change (ΔC _p) accompanying the glass transition is the significant measure of degree of changes in the structure of glass preceding crystallization. This revised version was published online in July 2006 with corrections to the Cover Date.     

镍-磷/纳米碳管化学复合镀层的研究

The electroless Ni-P-carbon nanotubes composite plating was studied on the copper substrate. Metallurgical microscope, scanning electronic microscope, X-ray diffractometer and micro hardness tester were used to study the structure, constitution and performance of the electroless Ni-P-carbon nanotubes composite deposit. Experiential results show that, with the increment of carbon nanotubes content in electroless plating solution, the grain size on the sample surface decreases whereas the density of grains and the hardness for composite deposit increases. Moreover, adding carbon nanotubes not only improves the degree of crystallization for the composite deposit but also helps their transformation from the amorphous state to the nanocrystal state.     

退火处理对新型无镁Y0.7La0.3Ni3.25Al0.1Mn0.15储氢合金结构和电化学性能的影响

通过电弧熔炼制备了无镁La-Y-Ni系A₂B₇型Y_0.7La_0.3Ni_3.25Al_0.1Mn_0.15合金, 并在高纯0.2 MPa Ar气氛下分别对合金进行850~1050 ℃真空24 h退火热处理. 通过X射线衍射(XRD)、 中子衍射(ND)、 扫描电子显微镜/能量分散谱(SEM/EDS)和电化学测试方法研究了退火温度对合金结构和性能的影响. 结构分析表明, 铸态合金由CaCu₅, Ce₅Co₁₉, Gd₂Co₇, Ce₂Ni₇多相构成, 随着退火温度升高, CaCu₅, Ce₅Co₁₉, Gd₂Co₇相逐步减少直至消失, Ce₂Ni₇主相相丰度逐步增加. 900~950 ℃退火时, 合金为单相Ce₂Ni₇结构. 退火温度继续升高, 合金中出现少量PuNi₃相. 合金电极的最大放电容量随着退火温度的升高先增加后降低. 从铸态的307.6 mA·h/g增加到900 ℃退火时的最大值393.1 mA·h/g, 后又降到1050 ℃退火时的366.4 mA·h/g. 合金电极的电化学循环稳定性随退火温度的升高而升高, 循环100次后电化学容量保持率(S₁₀₀)从铸态的66%上升到1050 ℃退火后的88.5%, 900~950 ℃退火时, 合金电极具有较好的综合电化学性能.     

非水体系中电解镍中间产物制备纳米NiO

采用纯镍为阳极，乙酰丙酮和乙醇的混合溶液中加入少量有机胺导电盐为电解液，施加一定电流使镍溶解，然后将电解液直接水解，控制一定的水解条件，制备得到纳米NiO粉体. 采用拉曼光谱、红外光谱、元素分析、XRD 和TEM 分别对电解得到的纳米NiO前驱体和纳米NiO进行了分析与表征, 并探讨了电化学溶解镍金属法制备纳米NiO反应的影响因素.电化学溶解镍金属得到的前驱体为Ni(OEt)2(acac)2,这种不溶性镍醇盐配合物升温至40～50℃即可溶解于乙醇溶液中,可直接应用于溶胶 凝胶(Sol gel)过程.水解后的纳米NiO呈无定形结构, 350 ℃煅烧后形成立方晶型NaCl结构, 纳米NiO经600 ℃煅烧后粒径分布在5～10 nm. 该方法理论上为二价不溶性金属醇盐经溶胶 凝胶工艺制备纳米氧化物材料提供了一条新的途径.     

EXAFS研究Ni-B和Ni-Ce-B超细非晶态合金的退火晶化

采用同步辐射EXAFS技术定量地研究化学还原法制备的Ni-B和Ni-Ce-B超细非晶态合金中Ni原子的局域环境结构随退火温度升高而产生的变化,结果表明,对于Ni-B和Ni-Ce-B超细非晶态合金初始样品：Ni-Ni最邻近配位壳层的平均键长RNi-Ni、配位数N、热无序σT、结构无序σs分别为0．275nm,11.9.0.0069nm,0.034nm;0.276nm,12.4,0.0067nm,0.035nm,Ni-B最邻近配位壳层的RNi-B,N, σT,σs分别为0．215nm,2.7,0.0055nm,0.0048nm;0.214nm,2.0,0.0058nm,0.0042nm,Ni-Ni配位的σs很大,是其σT的4－5倍,比Ni－B配位的σs大近一个数量级,在300℃退火后,Ni－B样品开始发生晶化生成晶态Ni3B,其RNi-Ni和σs分别为0．254nm和0．011nm,σs降低近2倍;而．3％原子比的Ce掺入后使Ni-Ce-B超细非晶态合金的晶化温度升高100℃左右。在500℃退火后,Ni－B样品的结构参数与Ni箔的相近,但Ni-Ce-B样品中的Ni-Ni配位的σs仍为0．0073nm,Ni-B配位的N为1．2,表明稀土元素Ce（以CeO2)显著增强了Ni与B的相互作用,且同时使退火晶化成的Ni晶结构产生畸变。     

陶瓷基钯银合金膜制备技术及性能研究

报道采用浆料涂敷与化学镀相结合法在陶瓷支撑上沉积钯银合金膜,采用浆料涂敷法,将含钯银的浆料涂敷在支撑体上,干燥后热分解,使支撑体表面沉积部分钯银。然后,采用化学镀在50℃下沉积钯银膜,热处理后,得到表面较光洁、厚度约为3μm、银含量为23%(原子百分含量)、合金化较完全的钯银合金膜,该膜在压差为0.1MPa,温度为300℃时的渗氢通量达45cm^3(STP)/(cm^2·min),分离因子达500,研究了钯银合金膜中银含量随热处理温度的变化规律,由实验结果发现,银逐渐向表面扩散,并在一定的温度条件达到基本平衡。