Preparation of nanoporous MgO-coated TiO2 nanoparticles and their application to the electrode of dye-sensitized solar cells

Sol-gel-derived Mg(OH)(2) gel was coated onto TiO(2) nanoparticles, and the subsequent thermal topotactic decomposition of the gel formed a highly nanoporous MgO crystalline coating. The specific surface area of the electrode that was prepared from the core-shell-structured TiO(2) nanoparticles significantly increased compared with that of the uncoated TiO(2) electrode. The increase in the specific surface area of the MgO-coated TiO(2) electrode was attributed to the highly nanoporous MgO coating layer that resulted from the topotactic reaction. Dye adsorption behavior and solar cell performance were significantly enhanced by employing the MgO-coated TiO(2) electrode. Optimized coating of a MgO layer on TiO(2) nanoparticles enhanced the energy conversion efficiency as much as 45% compared to that of the uncoated TiO(2) electrode. This indicates that controlling the extrinsic parameters such as the specific surface area is very important to improve the energy conversion efficiency of TiO(2)-based solar cells.     

Microstructure design of nanoporous TiO2 photoelectrodes for dye-sensitized solar cell modules

The optimization of dye-sensitized solar cells, especially the design of nanoporous TiO2 film microstructure, is an urgent problem for high efficiency and future commercial applications. However, up to now, little attention has been focused on the design of nanoporous TiO2 microstructure for a high efficiency of dye-sensitized solar cell modules. The optimization and design of TiO2 photoelectrode microstructure are discussed in this paper. TiO2 photoelectrodes with three different layers, including layers of small pore size films, larger pore size films, and light-scattering particles on the conducting glass with the desirable thickness, were designed and investigated. Moreover, the photovoltaic properties showed that the different porosities, pore size distribution, and BET surface area of each layer have a dramatic influence on short-circuit current, open-circuit voltage, and fill factor of the modules. The optimization and design of TiO2 photoelectrode microstructure contribute a high efficiency of DSC modules. The photoelectric conversion efficiency around 6% with 15 x 20 cm2 modules under illumination of simulated AM1.5 sunlight (100 mW/cm2) and 40 x 60 cm2 panels with the same performance tested outdoor have been achieved by our group.     

Preparation of nanocrystalline TiO2 thin film at low temperature and its application in dye-sensitized solar cell

The electrophoretic deposition combined with common pressure hydrothermal treatment was employed to prepare nanocrystalline TiO₂ thin film from suspension of tetra-n-butyl titanate and P25 at low temperature. The tetra-n-butyl titanate was hydrolyzed and crystallized into anatase to interconnect nanocrystalline TiO₂ particles and to stick them to a conductive substrate by common pressure hydrothermal treatment to improve the electron transport properties of the deposited thin film. A dye-sensitized solar cell based on TiO₂ thin film prepared by the low temperature method yielded the conversion efficiency of 6.12%. Due to the relative slower electron transport rate in the deposited film, its conversion efficiency was slightly lower than that of the cell with TiO₂ thin film prepared by the conventional high temperature sintering method. Since it is free of high temperature sintering step, this method can be used to prepare nanocrystalline TiO₂ thin film on plastic polymer conductive substrate for fabrication of flexible dye-sensitized solar cell.     

Double-layer coating of SrCO3/TiO2 on nanoporous TiO2 for efficient dye-sensitized solar cells

Surface modification plays a crucial role in improving the efficiency of dye-sensitized solar cells (DSSCs), but the reported surface treatments are in general superior to the untreated TiO(2) but inferior to the typical TiCl(4)-treated TiO(2) in terms of solar cell performance. This work demonstrates a two-step treatment of the nanoporous titania surface with strontium acetate [Sr(OAc)(2)] and TiCl(4) in order, each step followed by sintering. An electronically insulating layer of SrCO(3) is formed on the TiO(2) surface via the Sr(OAc)(2) treatment and then a fresh TiO(2) layer is deposited on top of the SrCO(3) layer via the TiCl(4) treatment, corresponding to a double layer of Sr(OAc)(2)/TiO(2) coated on the TiO(2) surface. As compared to the typical TiCl(4)-treated DSSC, the Sr(OAc)(2)-TiCl(4) treated DSSC improves short-circuit photocurrent (J(sc)) by 17%, open-circuit photovoltage (V(oc)) by 2%, and power conversion efficiency by 20%. These results indicate that the Sr(OAc)(2)-TiCl(4) treatment is better than the often used TiCl(4) treatment for fabrication of efficient DSSCs. Charge density at open circuit and controlled intensity modulated photocurrent/photovoltage spectroscopy reveal that the two electrodes show almost same conduction band level but different electron diffusion coefficient and charge recombination rate constant. Owing to the blocking effect of the SrCO(3) layer on electron recombination with I(3)(-) ions, the charge recombination rate constant of the Sr(OAc)(2)-TiCl(4) treated DSSC is half that of the TiCl(4)-treated DSSC, accounting well for the difference of their V(oc). The improved J(sc) is also attributed to the middle SrCO(3) layer, which increases dye adsorption and may improve charge separation efficiency due to the blocking effect of SrCO(3) on charge recombination.     

Improving the performance of solid-state dye-sensitized solar cell using MgO-coated TiO2 nanoporous film

An ultrathin overlayer of MgO on TiO2 is shown to drastically improve the stability of solid-state dye-sensitized solar cell using CuI as a hole conductor in addition to solar energy conversion efficiency.     

Partially nanowire-structured TiO2 electrode for dye-sensitized solar cells

Partially nanowire-structured TiO₂ was prepared by a hydrothermal processing followed by calcination in air. The hydrogen titanate powder as-synthesized was calcined at 300 °C for 4 h to obtain the partially nanowire-structured TiO₂. A dye-sensitized solar cell (DSC) with a film thickness of 5.6 μm, fabricated using the partially nanowire-structured TiO₂ showed better performance than using a fully nanowire-structured TiO₂ or a conventional equi-axed TiO₂ nanopowder. The short-circuit current density (J_SC), the open-circuit voltage (V_OC), the fill factor (FF) and the overall efficiency (η) are 11.9 mA/cm², 0.754 V, 0.673 and 6.01 %, respectively. The effects of one-dimensional nanostructure and electron expressway concept are discussed.     

Green synthesis and dye-sensitized solar cell application of rutile and anatase TiO2 nanorods

Journal of Solid State Electrochemistry - Nanorods (NRs) of TiO2 have biogenically been prepared, i.e., from the extract of Phellinus linteus mushroom. The presence of mixed anatase and...     

Energy-storable dye-sensitized solar cell with a polypyrrole electrode

A three-electrode-type solar-rechargeable battery, energy-storable dye-sensitized solar cell (ES-DSSC), has been constructed by the hybridization of a typical Gratzel cell and a conducting polymer charge-storage electrode; efficient photo-charging can be accomplished by visible-light irradiation.     

Porosity effects on electron transport in TiO2 films and its application to dye-sensitized solar cells

Porosity (P) of TiO2 film in dye-sensitized solar cells affects the light absorption coefficient and electron diffusion coefficient. A theoretical analytical expression of the intensity-modulated photocurrent spectroscopy (IMPS) response involving the light absorption coefficient and the electron diffusion coefficient as a function of the porosity has been proposed to investigate the influence of TiO2 film porosity on the characteristics of electron transport. The incident photon-to-current conversion efficiency (IPCE) and electron transit time depending on the porosity have been analyzed illuminating from both the electrolyte side (IE) and the substrate side (IS). The IPCE derived from the IMPS response reaches its maximum at a porosity of around 30% for IE and 41% for IS, respectively. Electron transit time increases with increasing the porosity for IE, while it declines when P < 0.41 for IS, which is attributable to the influence of the RC time constant. It has also been found that a larger RC time constant will lead to a longer transit time. The electron diffusion coefficient calculated from the transit time for IE corresponds to the results from the porosity reported in previous literature, which indicates that the dependence of the electron transit time tau(d) on the porosity is justifiable. The diffusion coefficient calculated for a larger RC time constant approaches the value from the literature when P > or = 0.41, while it is not practicable when P < 0.41 for IS.     

Spatial electron distribution and its origin in the nanoporous TiO2 network of a dye solar cell

Dye solar cells have been investigated by charge carrier extraction under short and open circuit conditions and an illumination intensity equivalent to 1 sun (AM 1.5). Under short circuit conditions, a surprisingly high amount of charge carriers stored in the nanoporous TiO2 network has been observed. A theoretical model was developed to describe the charge transport in the nanoporous TiO2 network of a dye solar cell, and the spatial distribution of the electron concentration was calculated. These results were compared with the experimental data of charge carriers stored in the TiO2 network under short and open circuit conditions. We were able to conclude that under short circuit conditions, the electrochemical potential of the electrons in the region far from the electrode is up to 550-570 meV higher than that of the electrons at the front electrode. This internal voltage is the driving force across the nanoporous TiO2 film under short circuit conditions.     

Facile preparation of large aspect ratio ellipsoidal anatase TiO2 nanoparticles and their application to dye-sensitized solar cell

A simple one-step heat-treatment of peroxotitanate complex aqueous solution at around 100 °C was resulted in the formation of ellipsoidal anatase TiO₂ nanoparticles having a high aspect ratio with no branches. The length of these ellipsoidal TiO₂ falls in the range of 200–350 nm, depending on mole ratio of Ti⁴⁺/H₂O₂. Dye-sensitized solar cell based on these ellipsoidal nanocrystalline TiO₂ as photoanode was fabricated and characterized.     

Improvement of dye-sensitized solar cell performance through electrodepositing a close-packed TiO2 film

A simple electrodepositing method was proposed for fabricating a uniform, tight, and close-packed TiO₂ nanocrystalline film on the ITO substrate. The electrode and dye-sensitized solar cell (DSSC) with electrodeposited TiO₂ layer were characterized by scanning electron microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. The phthalocyanin dye, zinc tetra-carboxyl phthalocyanin complex, was used as a model dye to evaluate the influence of close-packed TiO₂ blocking layer on the photocurrent–voltage property. On the electrodeposition, the close-packed TiO₂ layer could effectively inhibit the recombination of charges, and therefore improve the performances of the corresponding cells. The effects of film thickness on light transmittance and photocurrent density of the corresponding cell were also demonstrated. The optimum film thickness was found to be approximately 400 nm. At the optimum thickness, the photocurrent density greatly increased comparing with that of the screen printing TiO₂ film. These results imply that our proposition was a potential and feasible method for the fabrication of DSSC practically.     

Nanocrystalline TiO2/ZnO thin films: fabrication and application to dye-sensitized solar cells

Nanocrystalline TiO2 thin films composed of densely packed grains were deposited onto indium-doped tin oxide (ITO)-coated glass substrates at room temperature using a chemical bath deposition technique. A layer-by-layer (LbL) process was utilized to obtain a 1.418-microm-thick TiO2/ZnO structure. The TiO2 surface was super-hydrophilic, but its hydrophilicity decreased considerably after ZnO deposition. Other TiO2/ZnO films were studied to assess their suitability as photoelectrodes in dye-sensitized solar cells (DSSCs).     

Preparation of highly ordered TiO2 nanotubes on Ti-foil for dye-sensitized solar cells

TiO₂ nanotube arrays were grown on Ti foil in mixed electrolyte by the anodizing process. TiO₂ nanotube arrays were immersed in the TiCl₄ solution to improve the photocurrent by enhanced charge transfer between TiO₂ and dye molecules on the activity surface. Internal resistance of dye-sensitized solar cells (DSSC) was measured by impedance spectroscopy measurements. Backside illuminated DSSC with TiCl₄-treated TiO₂ nanotubes exhibited a conversion efficiency of 1.45% and showed improved electron transfer.     

Preparation of a novel polymer gel electrolyte based on N-methyl-quinoline iodide and its application in quasi-solid-state dye-sensitized solar cell

Using poly(acrylonitrile-co-styrene) as polymer host, 1,2-propanediol carbonate, dimethyl carbonate and ethylene carbonate as mixture solvent, N-methyl-quinoline iodide and iodine as the source of I⁻/I₃ ⁻, a novel polymer gel electrolyte with ionic conductivity of 5.12 × 10⁻³ S· cm⁻¹ at 25°C was prepared by sol-gel and hydrothermal methods. Based on the polymer gel electrolyte, a quasi-solid-state dye-sensitized solar cell was fabricated. The solar cell possess better long-term stability and light-to-electrical energy conversion efficiency of 4.04% under irradiation of 100 mW· cm⁻². The influences of polymer host, solvent, N-methyl-quinoline iodide and temperature on ionic conductivity of the polymer gel electrolyte and the performance of the dye-sensitized solar cell was discussed.     

Low-temperature formation of efficient dye-sensitized electrodes employing nanoporous TiO2 spheres

300-nm-sized nanoporous TiO₂ spheres (SPs), blended with 25-nm-sized nanoparticles, were successfully applied to low-temperature fabrication of TiO₂ electrodes for dye-sensitized solar cell (DSC). The introduction of SPs increased the adsorbed amount dye molecules, induced the efficient transport of photo-injected electrons through TiO₂ layer, and offered an extended light-scattering efficiency in the long wavelength region. Furthermore, the adhesion of TiO₂ layer to the FTO substrate was considerably improved. As a result, the photovoltaic conversion efficiency (η) of DSC processed at 140 °C was enhanced from 4.4% to 6.3%.     

A simple recipe for an efficient TiO2 nanofiber-based dye-sensitized solar cell

Development of highly efficient dye-sensitized solar cells (DSSCs) with good photovoltaic parameters is an active research area of current global interest. In this article, we provide a simple recipe for the fabrication of electrospun TiO(2) nanorod-based efficient dye-sensitized solar cell using a Pechini-type sol. The Pechini-type sol of TiO(2) nanofibers produces a highly porous and compact layer of TiO(2) upon doctor-blading and sintering without the need for an adhesion and scattering layers or TiCl(4) treatment. The best nanofiber DSSCs with an area of ~0.28 cm(2) shows an efficiency of ~4.2% under standard test conditions (100 mW/cm(2), 25°C and AM1.5 G) and an incident photon-to-electron conversion efficiency (IPCE) of ~50%. Impedance measurements show lower charge transfer resistance that improved the fill factor. We believe that simple approaches such as the present one to develop nanofiber DSSCs would open up enormous possibilities in effective harvesting of solar energy for commercial applications, considering the fact that electrospinning is a cost-effective method for the mass scale production of nanofibers and nanorods.     

Pyrolytic carbon from an aromatic precursor and its application as a counter electrode in dye-sensitized solar cells

Pyrolytic carbon thin films were deposited on quartz plates through a chemical vapor deposition process, by using a biphenyl precursor, 4,4'-bis(chloromethyl-1,1'-biphenyl). The pyrolytic carbons were microporous and catalytic toward reduction of tri-iodide, and the films thus obtained possessed a metallic appearance with good mirror reflections, hydrophilic surfaces, and low sheet resistances. The pyrolytic carbon-coated quartz plates were used, in place of the commonly used Pt-coated fluorine-doped tin oxide glass, as the counter electrode for dye-sensitized solar cells (DSSCs). The light to electricity conversion efficiency of the cell thus obtained was reasonably high, achieving 78% of that obtained by using the conventional but much more expensive Pt counter electrode. From the electrochemical impedance spectroscopic analysis, one found that the minor reduction in the conversion efficiency came from the relatively higher resistance and lower catalytic activity of the pyrolytic carbon. This work demonstrates that the newly developed pyrolytic carbon films may be a promising alternative to Pt as the counter electrode material for DSSCs.     

静电喷雾法制备高效染料敏化太阳能电池的二氧化钛光阳极

TiO2光阳极膜是染料敏化太阳能电池（DSSC）的核心部件之一,它对电池的光电转换效率起决定性作用．TiO2电极一般采用刮涂法和丝网印刷法制备．近3年,通过静电喷雾制备光阳极的方法得到国内外学者的关注．静电喷雾制备光阳极会受到多种因素的影响,如电压、流速、悬浮液浓度、喷雾距离以及喷雾时间等．但这些因素对成膜和DSSC器件性能的影响却没有得到全面的研究或者报道．本文使用静电喷雾法制备了多孔TiO2纳米膜,并研究了以其为电极的电池器件特性．经过超声充分分散的稳定TiO2乙醇悬浮液在高电压下喷雾到导电玻璃上成膜．通过改变电喷雾距离,得到了具有不同形貌的TiO：光阳极膜,并解释了其形成的机理及其对电池性能的影响．研究还表明,光阳极膜的TiC14处理能够很好地改善电池性能．通过优化,基于流速为0．8mL／h、电喷雾距离和时间分别为2．2cm和8min条件下制备的光阳极,结合TiC14处理,组装的电池在模拟太阳光源AM1．5G下光电转化效率达6．24％．     

Preparation of large-area dye-sensitized solar cells based on hydrothermally synthesized nitrogen-doped TiO2 powders

Low-cost, yellowish, nanocrystalline nitrogen-doped titanium dioxide (N-doped TiO₂) powder was synthesized by a hydrothermal method. The as-prepared N-doped TiO₂ powder was characterized by X-ray diffraction, transmission electron microscopy (TEM), UV–Vis absorption spectra, X-ray photoelectron spectroscopy (XPS), and Brunauer–Emmett–Teller analysis techniques. The grain size of the prepared powder was around 13 nm as estimated by both Scherrer’s method and TEM images. The effect of the ratio of N-doped TiO₂ particles to Degussa P25 on the photovoltaic performance of large-area dye-sensitized solar cells (DSSCs) was also investigated. The N-doped TiO₂ electrode showed higher photovoltaic performance compared with that of pure P25 at constant irradiation of 100 mW cm^?2, which is attributed to the large pore size and high surface area of N-doped TiO₂ resulting in the introduction of extra charge carrier pathways that could be beneficial for overall charge transportation. Energy conversion efficiency of 5.12 % was achieved in a DSSC device with active area of 51.19 cm².