钨含量对W/SiO2/Al2O3催化剂上1-丁烯自歧化反应的影响

采用浸渍法制备了一系列钨负载量不同的W/SiO₂/Al₂O₃ 催化剂. 采用X 射线衍射(XRD)、激光拉曼(Raman)光谱、紫外-可见(UV-Vis)光谱、氢气程序升温还原(H₂-TPR)和氨程序升温脱附(NH₃-TPD)等技术对催化剂进行了表征. 实验结果表明: 钨的负载量对催化剂上氧化钨物种的分散程度、还原性以及催化剂的酸性有非常重要的影响. 对该类催化剂上1-丁烯自歧化反应进行了详细考察, 结果表明: 当钨的质量分数为6.0%时,W/SiO₂/Al₂O₃催化剂表现出最佳的歧化活性和稳定性. 原因在于6.0%的钨负载量可以使催化剂上氧化钨物种具有中等程度的分散性、合适的还原性, 并且使催化剂具有一定程度的酸性, 这些因素有利于在催化剂上形成烯烃歧化活性位.     

NO选择性催化还原Ce-Mn-Ti-O催化剂铈组分助催化作用

用NH3程序升温脱附(NH3-TPD)、X射线衍射(XRD)、X射线光电子能谱(XPS)、H2程序升温还原(H2-TPR)和BET表面积测试结合NO选择性催化还原(SCR)微型反应评价等方法,研究了溶胶-凝胶法制备的Ce-Mn-Ti-O复合氧化物催化剂中铈组分的助催化作用.结果表明随铈含量增加,NO转化率大幅度增加,在Ce/Mn摩尔比约0.08时达极大值,其后随铈含量进一步增加,NO转化率又逐渐下降.适量铈组分的加入对Mn-Ti-O催化剂表面酸性影响不大,但增加了催化剂活性组分Mn物种的表面浓度,提高了Mn4+物种的相对含量和Mn物种的可还原性,从而提高催化剂低温SCR活性.当Ce/Mn摩尔比超过0.08,催化剂表面的Mn组分与Ce组分可能形成无定型结构的多层聚集的Ce-O-Mn物种,导致催化剂Mn/Ti摩尔比下降和Mn物种可还原性下降,从而导致催化剂SCR活性的下降.     

States of Carbon Nanotube Supported Mo-Based HDS Catalysts

The dispersion of the active phase and loading capacity of the Mo species on carbon nanotube (CNT) was studied by the XRD technique. The reducibility properties of Co-Mo catalysts in the oxide state over CNTs were investigated by TPR, while the sulfided Co-Mo/CNT catalysts were characterized by means of the XRD and LRS techniques. The activity and selectivity with respect to the hydrodesulfurization (HDS) performances on carbon nanotube supported Co-Mo catalysts were evaluated. It was found that the main active molybdenum species in the oxide state MoO3/CNT catalysts were MoO2, but not MoO3, as generally expected. The maximum loading before the formation of the bulk phase was lower than 6% (percent by mass, based on MoO3). TPR studies revealed that the active species in the oxide state Co-Mo/CNT catalysts were reduced more easily at relatively lower temperatures in comparison to those of the Co-Mo/γ-Al2O3 catalysts, indicating that the CNT support promoted or favored the reduction of the active species. The active species of a Co-Mo-0.7/CNT catalyst were more easily reduced than those of the Co-Mo/CNT catalysts with Co/Mo atomic ratios of 0.2, 0.35, and 0.5, respectively, suggesting that the Co/Mo atomic ratio has a great effect on the reducibility of the active species. It was found that the incorporation of cobalt improved the dispersion of the molybdenum species on the support, and a phenomenon of mobilization and re-dispersion had occurred during the sulfurization process, resulting in low valence state Mo3S4 and Co-MoS2.17 active phases. HDS measurements showed that the Co-Mo/CNT catalysts were more active than the Co-Mo/γ-Al2O3 ones for the desulfurization of DBT, and the hydrogenolysis/hydrogenation selectivity of the Co-Mo/CNT catalysts was also much higher than those of the Co-Mo/γ-Al2O3. The Co-Mo/CNT catalyst with a Co/Mo atomic ratio of 0.7 showed the highest activity, whereas the catalyst with a Co/Mo atomic ratio of 0.35 had the highest selectivity.     

Characterization of CuO supported on tetragonal ZrO2 catalysts for N2O decomposition to N2

A series of tetragonal zirconia-supported CuO oxide catalysts with various CuO loadings were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), electron spin resonance (ESR), ultraviolet and visible diffuse reflectance spectroscopy (UV/vis-DRS), and temperature-programmed reduction (TPR) measurements. The results indicate that the dispersion capacity of copper oxide on this support is approximately 8.6 Cu(2+) ions/nm(2) ZrO(2). The state of the resulting supported copper species depends on the CuO loading. At CuO loadings below the dispersion capacity, only highly dispersed copper ion species are present on the surface of t-ZrO(2). In particular, isolated Cu ions are the predominant species at low loadings. In contrast, pair Cu ions become the most abundant species at loadings near the dispersion capacity. It has been proposed that these dispersed CuO (isolated and paired Cu ions) have a symmetric 5-fold-oxygen-coordination symmetry (C(3)(v) symmetry) and can be described as distorted octahedra with a missing corner or a trigonal bipyramids. Finally, at CuO loadings above the dispersion capacity the formation of crystalline CuO is observed. TPR results reveal that the dispersed Cu ion species have a different reducibility from CuO crystallites, presumably due to strong interactions between these species and the t-ZrO(2) support. The catalytic activity of these CuO/t-ZrO(2) catalysts for the decomposition of N(2)O can also be directly correlated to CuO dispersion, with paired Cu ions being the most active species for this reaction.     

Effect of niobium promoter on iron-based catalyst for Fischer-Tropsch reaction

Niobium-promoted Fe/CNTs catalysts were prepared using a wet impregnation method.Samples were characterized by nitrogen adsorption,H2-TPR,TPD,XRD and TEM.The Fischer-Tropsch Synthesis(FTS) was carried out in a fixed-bed microreactor at 220 ℃,1 atm and H2/CO=2 for 5 h.Addition of niobium into Fe/CNTs increased the dispersion,decreased the average size of iron oxide nanoparticles and the catalyst reducibility.Niobium-promoted Fe catalyst resulted in appreciable increase in the selectivity of C5+ hydrocarbons and suppressed methane formation.These effects were more pronounced for the 0.04%Nb/Fe/CNTs catalyst,compared to those observed from other niobium compositions.The 0.04%Nb/Fe/CNTs catalyst enhanced the C5+ hydrocarbons selectivity by a factor of 67.5% and reduced the methane selectivity by a factor of 59.2%.     

Al2O3负载Cu,Fe或Ni掺杂氧化钼催化乙苯氧化脱氢（英文）

Molybdenum-based catalysts supported on Al2O3 doped with Ni, Cu, or Fe oxide were synthesized and used in ethylbenzene dehydrogenation to produce styrene. The molybdenum oxide was sup-ported using an unconventional route that combined the polymeric precursor method (Pechini) and wet impregnation on commercial alumina. The samples were characterized by X-ray diffraction (XRD), N2 adsorption-desorption isotherms, temperature-programmed reduction of H2 (H2-TPR), and thermogravimetric (TG) analysis. XRD results showed that the added metals were well dis-persed on the alumina support. The addition of the metal oxide (Ni, Cu, or Fe) of 2 wt% by wet im-pregnation did not affect the texture of the support. TPR results indicated a synergistic effect be-tween the dopant and molybdenum oxide. The catalytic tests showed ethylbenzene conversion of 28%–53% and styrene selectivity of 94%–97%, indicating that the addition of the dopant improved the catalytic performance, which was related to the redox mechanism. Molybdenum oxides play a fundamental role in the oxidative dehydrogenation of ethylbenzene to styrene by its redox and acid–base properties. The sample containing Cu showed an atypical result with increasing conver-sion during the reaction, which was due to metal reduction. The Ni-containing solid exhibited the highest amount of carbon deposited, shown by TG analysis after the catalytic test, which explained its lower catalytic stability and selectivity.     

The structure and catalytic activity of anatase and rutile titania supported manganese oxide catalysts for selective catalytic reduction of NO by NH3

The structure and catalytic properties of anatase and rutile supported manganese oxide catalysts prepared by impregnation method have been studied by using X-ray diffraction (XRD), laser Raman spectroscopy (LRS), X-ray photoelectron spectroscopy (XPS), H(2) temperature-programmed reduction (H(2)-TPR) and BET surface area measurements combined with activity testing of selective catalytic reduction (SCR) of NO by NH(3). It has been shown that the manganese oxide loadings on the two TiO(2) supports exert great influences on the SCR activity. For the rutile supported manganese oxide catalysts, increasing manganese oxide loading leads to the increase of reducibility of dispersed manganese oxide species and the rate constant k, which reaches a maximum around 9.6 × 10(-6) mol g(Mn)(-1) s(-1) at 0.5 mmol Mn per 100 m(2) TiO(2). When the manganese oxide loading is beyond this value, the existence of amorphous MnO(x) multiple layers will certainly reduce the ratio of manganese oxide species exposed on the surface and the reducibility of dispersed manganese oxide species, resulting in the rapid decrease of rate constant k. The LRS and XPS results have revealed that for the anatase supported manganese oxide catalysts manganese oxide species exist in Mn(+4) as a major species with Mn(+3) species and partially undecomposed Mn-nitrate as the minor species. Under the SCR reaction conditions, Mn(+3) species on anatase are oxidized to Mn(+4) species, inserting in the surface of anatase and promoting the anatase-to-rutile transformation in the surface layers of the anatase support. Since these Mn(4+) cations are actually dispersed on the support with a rutile shell-anatase core structure and its concentration is very near to that of MnO(x)/TiO(2) (R) catalyst, the relation between the rate constant k and the MnO(x) loading on the anatase support is similar to that on the rutile support, and that the rate constant k values for anatase and rutile supported manganese oxide catalysts are very close at the same MnO(x) loading.     

负载型V2O5/TiO2催化剂表面分散状态和性质对氨选择性催化还原NO性能的影响（英文）

采用多种物理化学手段研究了不同负载量V2O5/TiO2催化剂的VOx物种分散状态、表面酸性、可还原性及其选择性催化还原(SCR)NO性能.结果表明,V2O5在锐钛矿TiO2表面的实测单层分散容量约为1.14mmol V/100m2TiO2,与"嵌入模型"的估算值相符,表明分散态的钒离子应键合在TiO2表面的八面体空位上.随着V2O5负载量的增加,V2O5/TiO2催化剂上NO转化频率(TOF)先急剧增加,至0.70mmol V/100m2TiO2(略超过分散容量的一半)时达到极大(约8.3×10-3s-1),然后又急剧下降;同时,孤立VOx物种可能倾向于分散在相邻的八面体空位上,且通过V-O-V化学键相连形成聚合的VOx物种,V-O-V键所占比例增加而V-O-Ti键所占比例减小,催化剂表面单位钒离子的Brnsted酸中心量增加,故催化剂的TOF急剧增加.随着负载量进一步增加,虽然催化剂表面单位钒离子的Brnsted酸中心量仍缓慢增加,但V-O-Ti键所占比例减少,导致钒离子的可还原性下降,另外,分散容量以上时晶相V2O5的形成也导致钒离子表面利用率下降,从而导致催化剂的TOF下降.桥式Brnsted酸位(V-O(H)-V)也是SCR反应活性中心之一,不同负载量V2O5/TiO2催化剂上SCR活性与表面VOx物种的分散状态、表面酸性和钒离子可还原性密切相关.     

Nickel ferrite spinel as catalyst precursor in the dry reforming of methane:Synthesis,characterization and catalytic properties

Dry reforming of methane by CO2 using nickel ferrite as precursor of catalysts was investigated.Nickel ferrite crystalline particles were prepared by coprecipitation of nitrates with NaOH or ammonia followed by calcination,or by hydrothermal synthesis without calcination step.The textural and structural properties were determined by a number of analysis methods,including X-ray diffraction (XRD),Raman spectroscopy and X-ray photoelectron spectroscopy (XPS),among which X-ray diffraction (XRD) was at room and variable temperatures.All synthesized oxides showed the presence of micro or nanoparticles of NiFe2O4 inverse spinel,but Fe2O3 (hematite) was also present when ammonia was used for coprecipitation.The reducibility by hydrogen was studied by temperature-programmed reduction (TPR) and in situ XRD,which showed the influence of the preparation method.The surface area (BET),particle size (Rietveld refinement),as well as surface Ni/Fe atomic ratio (XPS) and the behavior upon reduction varied according to the synthesis method.The catalytic reactivity was investigated using isopropanol decomposition to determine the acid/base properties.The catalytic performance of methane reforming with CO2 was measured with and without the pre-treatment of catalysts under H2 in 650-800 C range.The catalytic conversions of methane and CO2 were quite low but they increased when the catalysts were pre-reduced.A significant contribution of reverse water gas shift reaction accounted for the low values of H2 /CO ratio.No coking was observed as shown by the reoxidation step performed after the catalytic reactions.The possible formation of nickel-iron alloy observed during the study of reducibility by hydrogen was invoked to account for the catalytic behavior.     

Influence of Adding Molybdenum on Structure and Performance of FexOy/SBA-15 Catalysts in Selective Oxidation of Propene

Mixed iron and molybdenum oxide catalysts supported on nanostructured silica, SBA-15, were synthesized with various Mo/Fe atomic ratios ranging from 0.07/1.0 to 0.57/1.0. Structural characterization of as-prepared Mo_xO_y_Fe_xO_y/SBA-15 samples was performed by nitrogen physisorption, X-ray diffraction, and DR-UV-Vis spectroscopy. Adding molybdenum resulted in a pronounced dispersion effect on supported iron oxidic species. Increasing atomic ratio up to 0.21Mo/1.0Fe was accompanied by decreasing species sizes. Strong interactions between iron and molybdenum during the synthesis resulted in the formation of Fe−O−Mo structure units, possibly Fe₂(MoO₄)₃-like species. Reducibility of Mo_xO_y_Fe_xO_y/SBA-15 catalysts was investigated by temperature-programmed reduction experiments with hydrogen as reducing agent. The lower reducibility obtained when adding molybdenum was ascribed to both dispersion and electronic effect of molybdenum. Catalytic performance of Mo_xO_y_Fe_xO_y/SBA-15 samples was studied in selective gas-phase oxidation of propene with O₂ as oxidant. Adding molybdenum resulted in an increased acrolein selectivity and a decreased selectivity towards total oxidation products.     

In situ characterization of Pt catalysts supported on ceria modified TiO2 for the WGS reaction: influence of ceria loading

This work analyzes the influence of cerium content (6-15 wt%) on a TiO(2) support over the structure and water gas shift (WGS) activity of Pt catalysts. The structural properties of these Pt/Ce-TiO(2) catalysts were characterized by XRD, TEM and XANES. Physicochemical characterization of the catalysts showed differences in the structure and dispersion of Ce entities on the support with Ce loading. For the samples with low ceria content (6 wt%), cerium is deposited on the support in the form of CeO(x) clusters in a highly dispersed state in close interaction with the Ti atoms. The formation of CeO(x) clusters at low Ce-loading on the support facilitates the dispersion of small particles of Pt and improves the reducibility of ceria component at low temperatures. The changes in platinum dispersion and support reducibility with Ce-loading on the TiO(2) support lead to significant differences in the WGS activity. Pt supported on the sample with lower Ce content (6 wt%) shows better activity than those corresponding to catalysts with higher Ce content (15 wt%). Activity measurements coupled with catalysts characterization suggest that the improvement in the reducibility of the support with lower Ce content was associated with the presence of CeO(x) clusters of high reducibility that improve the chemical activity of the oxide-metal interfaces at which the WGS reaction takes place.     

助剂Cu对Ni/γ-Al2O3催化剂低温还原性能影响

制备了一系列铜质量分数不同的CuNi/γ-Al2O3催化剂，进行了TPR和XRD表征并测定了该系列催化剂对苯加氢制环己烷的催化活性。结果表明，助剂Cu的负载量对低温（160 ℃）还原后催化剂的催化活性影响很大，在铜镍原子摩尔比为1∶1时，催化剂具有较高的催化活性和稳定性；添加铜组分可促进镍在载体表面分散，使负载NiO的还原温度降低，催化活性提高。     

CuO/ZrO_2催化水煤气变换反应制氢:ZrO_2载体焙烧温度的影响

以经不同温度(120、250、350、450℃)焙烧处理的ZrO_2为载体,采用沉积-沉淀法制备了系列CuO/ZrO_2催化剂;考察了富氢气氛下催化剂的水煤气变换反应(WGS)催化性能。结果表明,CuO/ZrO_2催化剂的催化活性随ZrO_2载体焙烧温度的升高呈现先升高后降低的"火山型"变化趋势,在焙烧温度为250℃时取得最高值。采用X射线粉末衍射、N_2物理吸附-脱附、N_2O滴定、H_2程序升温还原和CO程序升温还原及质谱跟踪等技术研究了系列ZrO_2载体及CuO/ZrO_2催化剂的结构和还原性能。结果表明,随着ZrO_2焙烧温度的升高,一方面,CuO/ZrO_2催化剂的Cu分散度逐渐降低,与ZrO_2具有强相互作用的高分散活性Cu-[O]-Zr物种("[]"表示ZrO_2表面氧空位)逐渐减少;另一方面,Cu-[O]-Zr物种的还原能力逐渐增强,并诱导催化剂活性表面羟基的还原能力也相应增强(CO为还原剂),即降低了催化剂对WGS反应的起活温度。两方面的综合作用使得ZrO_2载体焙烧温度为250℃(中等温度)时,CuO/ZrO_2催化剂的WGS催化活性最高。     

制备条件对用于甘油蒸汽重整反应Ni基催化剂性能的影响

研究了制备参数对用于甘油蒸汽重整反应的Ni基催化剂性能的影响。采用过量浸渍法、等体积浸渍法和改进的平衡沉积过滤(EDF)法制备了一系列Al2O3负载的8 wt%Ni催化剂,运用X射线衍射(XRD)、电感耦合等离子体光谱仪、N2吸附-脱附、扫描电镜(SEM)、透射电镜和H2程序升温还原(TPR)表征了催化剂的表面和体相性质;采用CHN分析仪和SEM表征了使用后催化剂以测定其表面沉积的碳及其形貌。结果表明,制备方法对所制催化剂的织构、结构和表面性质影响很大,导致氧化铝表面Ni物种的分散和种类的不同。即使XRD和TPR结果证实形成了铝酸镍晶相,但Ni/Al-edf催化剂中β峰的贡献大于其它两个催化剂的,表明在这种情况下铝酸镍更容易还原。在550 oC以上CO2选择性增加和CO选择性不变,表明Ni/Al-wet和Ni/Al-edf催化剂可成功催化水汽变换反应。另外,650oC时Ni/Al-edf催化剂上甘油生成气相产物的转化率、氢气产率以及烯丙醇、乙醛和乙酸选择性最高,且它在所有催化剂中的积炭量也最低。将催化剂结构性质、分散度和还原性与其催化性能相关联,发现EDF法制得的催化剂比表面积和活性相分散度更高,更易被还原,因而其活性和生成H2的选择性更高,也更抗积碳。     

Controlling Metal-Oxide Reducibility for Efficient C−H Bond Activation in Hydrocarbons

Knowing the structure of catalytically active species/phases and providing methods for their purposeful generation are two prerequisites for the design of catalysts with desired performance. Herein, we introduce a simple method for precise preparation of supported/bulk catalysts. It utilizes the ability of metal oxides to dissolve and to simultaneously precipitate during their treatment in an aqueous ammonia solution. Applying this method for a conventional VO_x−Al₂O₃ catalyst, the concentration of coordinatively unsaturated Al sites was tuned simply by changing the pH value of the solution. These sites affect the strength of V−O−Al bonds of isolated VO_x species and thus the reducibility of the latter. This method is also applicable for controlling the reducibility of bulk catalysts as demonstrated for a CeO₂−ZrO₂−Al₂O₃ system. The application potential of the developed catalysts was confirmed in the oxidative dehydrogenation of ethylbenzene to styrene with CO₂ and in the non-oxidative propane dehydrogenation to propene. Our approach is extendable to the preparation of any metal oxide catalysts dissolvable in an ammonia solution.     

Al2O3改性CuO/Fe2O3催化剂水煤气变换反应性能

采用分步共沉淀法制备了不同Al₂O₃含量(0%-15% (w))的CuO/Fe₂O₃催化剂, 并进行水煤气变换反应(WGSR)评价测试. 制得的催化剂中含有复合物CuFe₂O₄, 其晶粒尺寸, 氧化还原性质和表面Cu分散通过相应表征手段加以研究. X 射线粉末衍射(XRD), 拉曼(Raman)光谱, N₂物理吸附, N₂O分解和CO₂程序升温脱附(CO₂-TPD)等表征技术说明适量Al₂O₃的加入可以促进尖晶石CuFe₂O₄发生由四方相向立方相的转变, 阻止催化剂中Cu烧结, 增大表面Cu分散, 增加弱碱性位点的数量. 此外, 采用H₂程序升温还原(H₂-TPR)技术探究改性的CuO/Fe₂O₃催化剂的还原性能. 关联结果发现, Al₂O₃掺杂在增大铜物种的耗氢量, 降低其还原温度方面起着重要的作用. 即Al₂O₃的添加促进CuO/Fe₂O₃催化剂中铜铁物种之间的协同作用. 结合活性测试和表征结果,适量的Al₂O₃ (10%(w))改性的催化剂具有较小的Cu颗粒尺寸、较大的Cu分散、较强的还原性能、较多数量的弱碱性位点, 因此具有更好的初始活性和热稳定性.     

高效WO3掺杂MCF催化剂的合成及其在环戊烯选择氧化制戊二醛反应中的应用

以钨酸钠和正硅酸乙酯为前驱体直接合成高含量WO₃掺杂介孔氧化硅泡沫(MCF)催化剂. 在773 K焙烧后显示出更高的热稳定性. 小角X射线散射, N₂-物理吸附和透射电子显微镜结果表明钨物种嵌入后, 材料仍保持MCF特征的三维织构介孔特征. 紫外拉曼和紫外可见漫反射光谱结果表明钨物种主要以孤立的或者低聚态的氧化钨形式存在, 所以在氧化钨质量分数(w)低于20%时氧化钨物种能够高度分散在载体上. 在环戊烯选择氧化制戊二醛反应中, 反应16 h 后环戊烯的转化率达到100%, 戊二醛的产率达到83.5%. 催化剂重复利用实验表明催化剂的稳定性较好, 没有钨物种的脱落. 这种优异的催化性能归结于合适的氧化钨含量和高分散的钨物种.     

Co-doping a metal (Cr,Mn, Fe,Co, Ni,Cu, and Zn) on Mn/ZSM-5 catalyst and its effect on the catalytic reduction of nitrogen oxides with ammonia

Selective catalytic reduction (SCR) of NO_x by NH₃ over a series of Mn–M/Z catalysts (M = Cr, Mn, Fe, Co, Ni, Cu, Zn, and Z = the ZSM-5 Zeolite) synthesized by wet impregnation method was investigated. Mn–Fe/Z, Mn–Co/Z, and Mn–Cu/Z catalysts exhibited approximately 100 % NO_x conversion over a wide temperature range (200–360 °C) in a defined atmospheric condition, which was noticeably greater than that of Mn–Cr/Z (340–360 °C). Furthermore, the effect of addition of second metal oxide species to the initial Mn/Z catalyst on the structure of catalysts was studied by several characterization techniques. BET measurements revealed high surface area and pore volume of the Mn–Cu/Z catalyst. In addition, the XRD and UV–Vis DR results showed that addition of co-doped metal oxide species improved the dispersion of metal ions and inhibited crystallization of metal oxides. UV–Vis studies also were in good accordance with DTA/TG results confirming the formation of cobalt oxide and copper oxide clusters in Mn–Co/Z and Mn–Cu/Z catalysts, respectively. The FTIR spectra of pyridine adsorption, in addition, suggested the Mn–Cu/Z catalyst contained the most Lewis acid sites leading to more NO_x adsorption capacity.     

Investigation of Fe−Ni Mixed‐Oxide Catalysts for the Reduction of NO by CO: Physicochemical Properties and Catalytic Performance

A series of Fe?Ni mixed‐oxide catalysts were synthesized by using the sol–gel method for the reduction of NO by CO. These Fe?Ni mixed‐oxide catalysts exhibited tremendously enhanced catalytic performance compared to monometallic catalysts that were prepared by using the same method. The effects of Fe/Ni molar ratio and calcination temperature on the catalytic activity were examined and the physicochemical properties of the catalysts were characterized by using XRD, Raman spectroscopy, N₂‐adsorption/‐desorption isotherms, temperature‐programmed reduction with hydrogen (H₂‐TPR), temperature‐programmed desorption of nitric oxide (NO‐TPD), and X‐ray photoelectron spectroscopy (XPS). The results indicated that the reduction behavior, surface oxygen species, and surface chemical valence states of iron and nickel in the catalysts were the key factors in the NO elimination. Fe_0.5Ni_0.5O_x that was calcined at 250 °C exhibited excellent catalytic activity of 100 % NO conversion at 130 °C and a lifetime of more than 40 hours. A plausible mechanism for the reduction of NO by CO over the Fe?Ni mixed‐oxide catalysts is proposed, based on XPS and in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) analyses.     

CuO-Ag2O/γ-Al2O3催化剂的TPR特性及氧化活性研究

采用程序升温还原技术(TPR)研究CuO-Ag2O/γ-Al2O3双组分及其单组分催化剂的还原特性以及热处理温度对其还原性能的影响。发现不同负载量的Cuo-Ag2O/γ-Al2O3催化剂的还原特性有明显差异, 反映出催化剂表面存在着不同种类的铜物种。Ag2O的存在, 使催化剂的TPR峰位与单组分CuO/γ-Al2O3的TPR曲线产生明显差异, 还原峰发生位移, 随Ag2O添加量的增加, 位移增大。对苯的完全氧化反应结果表明, 催化剂的氧化活性次序为:CuO-Ag2O/γ-Al2O3>CuO/γ-Al2O3>Ag2O/γ-Al2O3。热处理温度升高, 使催化剂表面铜物种分散状态及其还原性能发生变化。从500~900℃, 存在一个使铜物种达到最佳分散态的温度。讨论了负载于γ-Al2O3载体上的CuO-Ag2O双组分及其单组分催化剂在还原过程中金属与载体, 金属与金属间的相互作用以及热处理温度对其还原性能的影响。