Determination of Sulfite in Hair Waving Products Using Oxygen‐Incorporated Gold‐Modified Screen‐Printed Electrodes

An electrodeposition oxygen‐incorporated gold‐modified screen‐printed carbon electrode (AuOSPE) was fabricated to determine the sulfite content in hair waving products. The AuOSPE showed an electrocatalytic current for sulfite at +0.4 V (vs. Ag/AgCl). Compared with a gold screen‐printed electrode (AuSPE), the AuOSPE showed a higher electrocatalytic current. The increase in the electrocatalytic current was ascribed to the increase of the oxygen incorporated with gold atom on AuOSPE. The AuOSPE coupled with a flow injection analysis (FIA) system showed excellent oxidation current for sulfite in a 0.1 mol L^?1 phosphate buffer solution (PBS), pH 6.0. The linear working range for determining the sulfite content was 0.05 to 1200 mg L^?1 (0.625 µmol L^?1 to 15.00 mmol L^?1) with a calculated detection limit of 0.03 mg L^?1 (0.375 µmol L^?1) (DL, S/N=3). Relative standard deviations (RSD) of 3.03 %, 2.30 % and 4.26 % were calculated for consecutive injections (n=12) of 20, 300 and 900 mg L^?1 sulfite, respectively. The amount of sulfite in two hair waving products was determined by the proposed method and a standard iodometric method. The recoveries ranged from 96.18 % to 105.61 %. The AuOSPE showed high sensitivity, selectivity, stability and reproducibility for sulfite.     

Gold Nanoparticles Modified Titania Nanotube Arrays for Amperometric Determination of Ascorbic Acid

Development and use of highly ordered, vertically aligned TiO₂ nanotube arrays modified with gold nanoparticles for the selective detection of ascorbic acid (AA) in the presence of uric acid and glucose are reported here. Gold nanoparticles were electrodeposited on the Nanotube arrays by CV. The sensor was characterized using SEM, EDS, CV, and EIS. It showed very good performance with a sensitivity of 46.8 μA mM^?1 cm^?2, response time below 2 seconds and linearity in the range of 1 μM to 5 mM with a detection limit of 0.1 μM and was tested for the AA concentration in pharmaceutical preparations.     

Microsensor Chip Integrated with Gold Nanoparticles‐Modified Ultramicroelectrode Array for Improved Electroanalytical Measurement of Copper Ions

This paper presents a microsensor chip integrated with a gold nanoparticles‐modified ultramicroelectrode array (UMEA) as the working electrode for the detection of copper ions in water. The microsensor chip was fabricated with Micro‐Electromechanical System technique. Gold nanoparticles were electrodeposited onto the surface of UMEA at a constant potential of ?0.3 V. The ratio d/R_b of interelectrode spacing (d) over the individual electrode’s radius (R_b) was investigated to improve the electrochemical performance. The UMEA with a d/R_b of 20 showed the best hemispherical diffusion mode, resulted in fast response time and high current response. The gold nanoparticles increased the active surface area of UMEA by not changing the geometries of UMEA, and the current response was increased further. Incorporating the optimized characteristic of UMEA and gold nanoparticles, the microsensor showed a good linear range from 0.5 to 200 µg L^?1 of copper ions in the acetate buffer solutions with the method of square wave stripping voltammetry. Compared with the gold nanoparticles‐modified disk electrode, the gold nanoparticles‐modified UMEA showed higher sensitivity (0.024 µA mm^?2 µg^?1 L) and lower limit of detection (0.2 µg L^?1). Water samples from river water and tap water were analyzed by the microsensor chip with recovery ranging from 100.7 % to 107.8 %.     

Pulsed Amperometric Detection of Histamine at Glassy Carbon Electrodes Modified with Gold Nanoparticles

Gold nanocrystal‐modified glassy carbon electrodes (nAu‐GCE) were prepared and used for the determination of histamine by flow injection and high performance liquid chromatography using pulsed amperometric detection (PAD) as the detection mode. Experimental variables involved in the electrodeposition process of gold from a HAuCl₄ solution were optimized. A catalytic enhancement of the histamine voltammetric response was observed at the nAu‐GCE when compared with that obtained at a conventional Au disk electrode, as a consequence of the microdispersion of gold nanocrystals on the GC substrate. The morphological and electrochemical characteristics of the nAu‐GCE were evaluated by SEM and cyclic voltammetry. PAD using a very simple potential waveform consisting of an anodic potential (+700 mV for 500 ms) and a cathodic potential (?300 mV for 30 ms), was used to avoid the electrode surface fouling when histamine was detected under flowing conditions. Flow injection amperometric responses showed much higher I_p values and signal‐to‐noise ratios at the nAu‐GCE than at a conventional gold disk electrode. A limit of detection of 6×10^?7 mol L^?1 histamine was obtained. HPLC‐PAD at the nAu‐GCE was used for the determination of histamine in the presence of other biogenic amines and indole. Histamine was determined in sardine samples spiked at a 50 μg g^?1 concentration level, with good results. Furthermore, the chromatographic PAD method was also used for monitoring the formation of histamine during the decomposition process of sardine samples.     

聚N,N-双水杨醛乙二胺合钴修饰超微电极的制备及其在一氧化氮测定中应用的研究

通过电化学聚合法制备了聚Ｎ，Ｎ－双水杨醛乙二胺合钴［ｐｏｌｙＣｏ（Ｓａｌｅｎ）］修饰超微电极，研究了该修饰电极的电催化性质及其在一氧化氮（ＮＯ）测定中的应用．实验结果表明，ｐｏｌｙＣｏ（Ｓａｌｅｎ）修饰超微电极对ＮＯ的测定有高的灵敏度，ＮＯ的浓度在２．０×１０－８～２．８×１０－６ｍｏｌ／Ｌ范围内，电流与浓度呈良好的线性关系，线性相关系数为０．９９９８，检出限为１．０×１０－８ｍｏｌ／Ｌ；该电极进一步修饰Ｎａｆｉｏｎ后，生物体中常见的物质如抗坏血酸、儿茶酚胺类神经递质的代谢物、ＮＯ的氧化产物ＮＯ－２等不干扰测定．本传感器可以满足ＮＯ在体分析的需要．     

Electrocatalytic Oxidation and Determination of Sulfite with a Novel Copper‐Cobalt Hexacyanoferrate Modified Carbon Paste Electrode

The electrocatalytic oxidation of sulfite has been studied at a stable electroactive thin film of copper‐cobalt hexacyanoferrate (CuCoHCF) hybrid electrodeposited on a carbon paste electrode (ECMCPE). A linear range of 5 μM to 5 mM of sulfite, with an experimental detection limit of 1 μM, was obtained using the cyclic voltammetric method. The oxidation of sulfite showed no significant fouling effect on the modified electrode surface at sulfite concentrations below 5 mM. The proposed modified electrode exhibited several attractive features, including simple preparation, fast response, good stability and repeatability, and could be applied to sulfite determination in real samples.     

Sulfite Determination with Gold Electrode Promoted by bis(4-Pyridyl)disulphide/cytochrome C

Abstract

A biosensor was developed using oxidized cytochrome C - sulfite reaction by following the electrochemical reaction between reduced cytochrome C and gold electrode. The change in the current at the fixed potential equal to anodic peak potential of cytochrome C was proportional to sulfite concentration in the range of 0.4×10^?4 to 4.0×10^?4 M.     

Determination of Copper in the Presence of Various Amounts of Arsenic with L‐Cysteine Modified Gold Electrodes

An L ‐cysteine modified gold electrode for the determination of copper in the presence of various amounts of arsenic with anodic stripping voltammetry has been studied. The electrode was fabricated by immersing a gold electrode in an ethanol solution of 5mM L ‐cysteine for 60 min. Various parameters, such as the effect of different supporting electrolytes, the pH of the electrolyte and the deposition potential were investigated. Under optimum conditions, copper was accumulated at ?0.3 V (vs. SEC) for 60 s in 0.1 M phosphate buffer pH 5.0 in the presence of different amounts of arsenic. Essentially the same sensitivities (0.33±0.001 μA/μM) and limits of detection (0.13±0.002 μM) of copper were obtained with various amount of arsenic in the range 2 μM to 20 μM.     

巯基乙酸修饰金电极的电化学行为及对铜离子的测定

通过共价自组装的方法制备了巯基乙酸单分子层修饰金电极.在含有铜离子的磷酸缓冲液中搅拌吸附,铜离子与修饰电极表面的巯基乙酸形成的活性配合物吸附在电极表面.用该电极对不同浓度的铜离子进行检测,发现峰电流随铜离子浓度的增大而增大,在0.05~1μmol/L之间出现良好的线性关系,其最低检测限可达10 nmol/L.     

An In Situ Copper Plated Boron‐Doped Diamond Microelectrode Array for the Sensitive Electrochemical Detection of Nitrate

The first example of using a copper microelectrode array for use in electroanalysis is explored and exemplified with the electroanalytical quantification of nitrate. The analytical approach is based upon the in situ deposition of copper at a boron‐doped diamond (BDD) microelectrode array. The immobilized copper layer is electrocatalytic for nitrate reduction and exhibits an analytically useful range from 1.2 to 124 μM with a marked selectivity for nitrate ion over nitrate, with a limit of detection of 0.76 μM. The analytical applicability was examined through standard addition determinations of nitrate in drinking and river water samples.     

A Pencil Graphite Electrode In Situ Modified by Monovalent Copper: a Promising Tool for the Determination of Methylxanthines

A pencil graphite electrode (PeGE) exhibits a promising tool for the electrochemical analysis of xanthine (Xan) and its N‐methyl derivatives (1‐, 3‐, 7‐ and 9‐mXan). The changes in their level in blood, serum, urine, as products of purine catabolism, can indicate the development of some diseases. Sensitivity‐enhanced voltammetric detection of mXans was achieved by forming of complex with Cu(I) and application of elimination procedure. The Cu(I)‐mXan complex was identified by means of titration of electrochemically produced cuprous ions by mXan. Our approach enables separation of overlapped mXan oxidation signals. Based on the obtained results, we found that the effect of methyl group position on the xanthine skeleton was significant and it was also discussed.     

Gold and Nanogold Electrodes Modified with Gold Nanoparticles and meso‐2,3‐Dimercaptosuccinic Acid for the Simultaneous,Sensitive and Selective Determination of Dopamine and Its Biogenic Interferents

Gold and nanogold electrodes modified with self‐assembled layers composed of gold nanoparticles and organic sulfur compounds were applied for quantitative determination of dopamine and its biogenic interferents like: ascorbic and uric acids. For the novel sensor a linear relationship between the current response of dopamine at the potential of peak maximum and the concentration was found over a wide analyte concentration range in solution with a very good detection sensitivity and detection limit. It was proved that current peaks of dopamine and both ascorbic and uric acids were clearly separated from each other enabling selective detection of these compounds coexisting in a mixture in solution of pH 7.     

Theoretical Analysis and Determination of the Heterogeneous Stability Constant of Copper(II)-Humic Acids Complex at Chemically Modified Carbon Paste Electrode

A theory for determining the heterogeneous stability constant of a metal complex system at the surface of a chemically modified carbon paste electrode was developed. The proposed theory has been applied to the studies of a copper(II)-humic acids (Has) complex system. In an open circuit, copper(II) was accumulated from a stirred preconcentration medium onto the HAs-CMCPE. The subsequent electrochemical measurement was performed in a small volume of Britton-Robinson (B-R) buffer (pH 3.78). By means of cyclic voltammetry (CV) and anodic stripping voltammetry (ASV), the determined average heterogeneous stability constant of copper(II)-HAs complex was 4.99×10⁹.     

Determination of Norepinephrine Alone and in the Presence of Ascorbic and Uric Acids Using a Gold Electrode Modified with Gold Nanoparticles and Self‐Assembled Layers of meso‐2,3‐Dimercaptosuccinic Acid

This paper reports on the modification of gold electrodes with self‐assembled layers (SAMs) composed of meso‐2,3‐dimercaptosuccinic acid, cysteamine and gold nanoparticles, respectively and their application to quantitative determination of norepinephrine alone and in the presence of ascorbic and uric acids in solution at pH 7. The modification was carried out on two kinds of templates: a bare gold electrode (2D electrode) and a gold electrode coated in the first step with gold nanoparticles (3D electrode). Cyclic voltammograms reveal an enhancement of the norepinephrine electrooxidation in comparison to a bare, (non‐modified) gold electrode. The oxidation peaks for norepinephrine, ascorbic acid and uric acid have a peak‐to‐peak separation that enables their selective determination even in a complex mixture.     

甲壳素修饰碳糊电极测定痕量铜

报道了采用甲壳素修饰碳糊电极测定痕量铜的方法。通过开路富集，Ｃｕ６２＋和甲壳素形成络合物富集于电极表面，然后经介质交换，电位还原再进行阳熔出伏安测定。在浓度为３．０×１０＾－９－９．０×１２０＾－７ｍｏｌ／Ｌ范围内，峰电流与痕量铜浓度呈线性关系，检测限为１．０×１０＾－９ｍｏｌ／Ｌ。同时，对电极反应的机理进行了讨论。     

Application of Square Wave Anodic Stripping Voltammetry for Determination of Traces of Ti(I) at Carbon Electrodes In Situ Modified with Bi Films

Bismuth films deposited in situ at glassy carbon and carbon film electrodes were tested for the determination of traces of Tl(I) separately and together with Zn(II) and Pb (II), in acetate buffer solution pH 3.7, using square wave anodic stripping voltammetry. Electrochemical impedance spectra in the presence of Tl(I) showed differences between the electrode substrates. The sensitivity to Tl does not depend on the presence of other ions, and was better at carbon film electrodes, although the 2 nmol L^?1 detection limit was independent of electrode substrate. Application to the measurement of Tl(I) in commercial berry juice is demonstrated.     

18－冠－6修饰碳糊电极测定金的研究

本文研究了１８－冠－６修饰碳糊电极测定金的条件，金在０．５ｍｏｌ／ＬＨＣ１－０．００５ｍｏｌ／ＬＫＣ１底液中富集，介质交换到０．０１ｍｏｌ／ＬＨＣ１中进行测定。金（Ⅲ）浓度在０．１～１．０μｇ／ｍＬ范围内呈线性关系，相对标准偏差为９．７％，检出限为２０ｎｇ／ｍＬ。可不经预先分离直接测定矿样中的金，结果良好。并研究了Ａｕ（Ⅲ）在１８－冠－６碳糊修饰电极上的还原机理。     

铁氰化镍化学修饰电极对亚硫酸根离子的电催化氧化及其应用

本文采用电化学方法在玻碳(GC)基体上制备出性能稳定的铁氰化镍(NiHCF)修饰膜电极,表征了NiHCF膜的电化学行为,研究了其对SO_3~(2-)离子的电催化氧化作用。结果表明,SO_3~(2-)离子在NiHCF/GC上氧化是受NiHCF媒介作用的,属EC平行催化反应。催化峰电流与SO_3~(2-)离子浓度在1.0×10~(-6)～2.0×10~(-2)mol/L范围内呈线性关系,检测限可达5.0×10~(-7)mol/L。用于测定空气中SO_2含量,结果良好。     

Electroanalysis of Pyridoxine at Copper Nanoparticles Modified Polycrystalline Gold Electrode

Pyridoxine is analyzed using square wave voltammetry (SWV) at copper nanoparticles (nano‐Cu) modified poly‐crystalline gold electrode (nano‐Cu/Au). Nano‐Cu/Au is fabricated by a potential scan electrodeosition technique. Nano‐Cu/Au electrode has been characterized morphologically and electrochemically. The analysis of pyridoxine at nano‐Cu/Au electrode is achieved utilizing the quenching of copper voltammetric response due to the complexation with pyridoxine forming an electroinactive complex. Pyridoxine selectively forms complex with copper ions (modifier), but not with Au (underlying substrate) as supported by UV/Vis spectrophotometry. Using SWV the calibration curve for pyridoxine analysis was obtained in the concentration range of 0.3–2.7 µM with high correlation coefficient. The proposed method has been successfully applied for the determination of pyridoxine in two dosage forms.     

化学修饰电极富集石墨炉原子吸收法测定痕量金

本文提出用聚丙烯脒硫氰酸盐化学修饰石墨管内壁、电化学预富集石墨炉原予吸收测定Au的分析方法.分析灵敏度提高100倍.应用于矿石中痕量Au的测定,获得了满意的结果.