Al Electrode Modified by Au Atoms as a Novel Electrode for Electrocatalytic Oxidation of Thiosulfate

An aluminum electrode modified with gold atoms was introduced as a novel electrode. Gold atoms were deposited both chemically and electrochemically onto the aluminum electrode to make an aluminum/gold (Al/Au) modified electrode (ME). The experimental results showed that the Al/Au modified electrode prepared by chemical deposition, exhibits much more current than the electrochemical deposition method. The electrochemical behavior of the Al/Au modified electrode was studied by cyclic voltammometry. This modified electrode showed two pairs of peaks, a₁c₁ and a₂c₂, with surface‐confined characteristics in a 0.5 M phosphate buffer. The dependence of E_pa of the second peak (a₂c₂) on pH shows a Nernestian behavior with a slope of 55 mV per unit pH. The effect of different supporting electrolytes, solution's pH and different scan rates on electrochemical behavior of Al/Au modified electrode was studied. Au deposited electrochemically on a Pt electrode (Pt/Au) was also used as another modified electrode. A comparative study of electrochemical behavior of bare Al, Pt/Au and Al/Au modified electrodes showed that both Pt/Au and Al/Au electrodes have the ability of electrocatalytic oxidation of S₂O₃^2?, but the electrocatalytic oxidation on the latter was better than the former. The kinetics of the catalytic reaction was investigated by using cyclic voltammetry and chronoamperometry techniques. The average value of the rate constant for the catalytic reaction and the diffusion coefficient were evaluated by means of chronoamperometry technique.     

Sb在Au电极上不可逆吸附的电化学过程

用电化学循环伏安法和电化学石英晶体微天平(EQCM)技术研究了Sb在Au电极上不可逆吸附的电化学过程. 研究结果表明, 在-0.25 V到0.18 V(vs SCE)范围内, Sb可在Au电极上稳定吸附, 并且在0.15 V附近出现特征氧化还原峰. 根据EQCM实验数据, 在电位0.18 V时, Sb在Au电极上的氧化产物是Sb2O3; 同时Sb的吸附阻止了电解液中阴离子和水在Au电极上的吸附. 当电极电位超过0.20 V时, Sb2O3会被进一步氧化成Sb5+化合物, 同时逐渐从Au电极表面脱附.     

Electorchemical Studies of Cytochrome c on Electodes Modified by Single—Wall Carbon Naotubes

Single-wall carbon nanotubes(SWNTs) modified gold electrodes were prepared by using two different methods.The electrochemical behavior of cytochrome c on the modified gold electrodes was investigated.The first kind of SWNT-modified electrode (noted as SWNT/Au electrode)was prepared by the adsorption of carboxylterminated SWNTs from DMF dispersion on the gold electrode.The oxidatively processed SWNT tips were covalently modified by coupling with amines (AET) to form amide linkage.Via Au-S chemical bonding,the self-assembled monolayer of thiol-unctionalized nanotubes on gold surface was fabricated so as to prepare the others SWNT-modified electrode (noted as SWNT/AET/Au electrode).It was shown from cyclic voltammetry cxperiments that cytochrome c exhibited direct electrochemical responses on the both electrodes, but only the current of controlled diffusion existed on the SWNT/Au electrode while both the currents of controlled diffusion and adsorption of cytochrome c occurred on the SWNT/AET/Au electrode.Photoelastic Modulation Infared Reflection Absorpthion Spectroscopy (PEM-IRRAS) and Quartz Crystal Microbalance (QCM) were employed to verify the adsorption of SWNTs on the gold electrodes.The results proved that SWNTs could enhance the direct electron transfer proecss between the electrodes and redox proteins.     

Voltammetry of basal plane platinum electrodes in acetonitrile electrolytes: effect of the presence of water

The first part of this report studies the electrochemical properties of single-crystal platinum electrodes in acetonitrile electrolytes by means of cyclic voltammetry. Potential difference infrared spectroscopy in conjunction with linear voltammetry was used to obtain a molecular-level picture of this interface. The second part of this report studies the hydrogen evolution and the hydrogen oxidation reactions on the three low-index faces of Pt electrodes in acetonitrile electrolytes. The data (CVs and IR spectra) strongly suggest that acetonitrile and CN(-) molecules are adsorbed on single-crystal platinum electrodes in the range of -1.5 to 0.3 V versus Ag/AgCl. Those species block part of the adsorption sites for hydrogen adatoms, and they decompose on the surface in the presence of water. The nature of the cation and the presence of water strongly affect the onset of acetonitrile electrolysis and the kinetics and stability of the adsorbed species on the electrode. Finally, the hydrogen evolution and the hydrogen oxidation reactions on platinum single-crystal surfaces in acetonitrile electrolytes are strongly affected by the surface-energy state of Pt electrodes.     

Electropolymerization of <Emphasis Type="Italic">trans</Emphasis>-[RuCl<Subscript>2</Subscript>(vpy)<Subscript>4</Subscript>] complex—EQCM and Raman studies

The electropolymerization of trans-[RuCl₂(vpy)₄] (vpy=4-vinylpyridine) on Au or Pt electrodes was studied by cyclic voltammetry, electrochemical quartz crystal microbalance (EQCM) technique, and Raman spectroscopy. Cyclic voltammetry of the monomer at a microelectrode shows the typical Ru(III/II) and Ru(IV/III) waves, together with the vinyl reduction waves at −1.5 and −2.45 V and adsorption wave at −0.8 V. Electrodeposition on EQCM technique performed under potential cycling between −0.9 and −2.0 V revealed that the polymerization proceeded well in advance of the vinyl reduction waves. At potentials more positive than −0.9 V, soluble oligomers were deposited irreversibly on the electrode during the oxidative sweep. The film also showed reversible mass changes due to the oxidation and accompanying ingress of charge-balancing anions and solvent into the film. In contrast, potentiostatic growth of the polymer at −1.6 V was slower because the oligomeric material was lost completely from the electrode. Unreacted vinyl groups were detected by in situ Raman spectroscopy for films grown at −0.7, −0.9, and −1.6 V but were absent when the polymerization was carried out at −2.9 V vs Ag/Ag⁺.     

Electrochemical Behavior of Irreversibly Adsorbed Sb on Au Electrode

The electrochemical processes of irreversibly adsorbed antimony (Sb_ad) on Au electrode were investigated by cyclic voltammetry (CV) and electrochemical quartz crystal microbalance (EQCM). CV data showed that Sb_ad on Au electrode yielded oxidation and reduction features at about 0.15 V (vs saturated calomel electrode, SCE). EQCM data indicated that Sb_ad species were stable on Au electrode in the potential region from −0.25 to 0.18 V (vs SCE); the adsorption of Sb inhibited the adsorption of water and anion on Au electrode at low electrode potentials. Sb₂O₃ species was suggested to form on the Au electrode at 0.18 V. At a potential higher than 0.20 V the Sb₂O₃ species could be further oxidized to Sb(V) oxidation state and then desorbed from Au electrode.     

Cobalt oxide electrodeposition on various electrode substrates from alkaline medium containing Co–gluconate complexes: a comparative voltammetric study

A study regarding the electrodeposition of Co oxides from alkaline medium containing 12?mM gluconate ligand and 12?mM Co²⁺ on glassy carbon, Au, Pt, Ni, Ti and ITO electrode substrate was carried out through cyclic voltammetry technique. Films of cobalt oxides were deposited either anodically by voltage cycling (100?mV?s^?1) between ?0.3 and 0.6?V (SCE) or by potentiostatic conditions at potential comprised between 0.2 and 0.6?V for a fixed time of deposition. Analysis of the voltammetric experimental data clearly showed that the rate of cobalt oxide electrodeposition process decreases in the order Au > Pt > GC, Ni > Ti, ITO and the massive cobalt electrodeposition does not proceed to an appreciable extent until potentials of 0.3–0.4?V (SCE) is reached. The effect of the scan rate on the peak potential, peak current, and peak-to-peak separation of the deposited cobalt oxide films was studied, and some substantial differences in terms of electrochemical behaviour in relation at the specific substrate electrode were observed and critically discussed.     

Sb在Pt(100),Pt(110),Pt(111)及Pt(320)上不可逆吸附的电化学特性

研究了Sb在Pt(1 0 0 ) ,Pt(1 1 0 ) ,Pt(1 1 1 )和Pt(32 0 )单晶面上不可逆吸附的电化学特性 .发现当扫描电位的上限Eu≤ 0 .45V时 ,Sbad可以稳定地吸附在Pt(1 0 0 ) ,Pt(1 1 0 )和Pt(1 1 1 )表面 ,而Sbad在Pt(32 0 )表面稳定的电位较低 ,为Eu≤ 0 .40V .从饱和吸附Sb的铂单晶电极出发 ,通过改变电位扫描上限Eu 和电位扫描圈数可以获得不同Sb覆盖度 (θSb)的电极 .根据Sb和H在铂单晶电极表面共吸附的定量数据 ,对Sb在不同铂单晶面上饱和吸附的模型进行了初步探讨 .     

Electroreduction of Oxygen and Electrooxidation of Methanol at Carbon and Single Wall Carbon Nanotube Supported Platinum Electrodes

The present research aimed at investigating the electrocatalytic properties and the electrochemical deposition of Pt nanoparticles on carbon powder, carbon nanotube and preparation of carbon and single wall carbon nanotube supported platinum electrodes. The Pt nanoparticles were synthesized by electroreduction of hexachloroplatinic acid in aqueous solution at ?200 mV. Electrocatalytic properties of the modified electrodes for oxygen reduction were investigated by cyclic voltammetry in O₂ saturated solution containing 0.1 M HClO₄. Methanol electrooxidation at the modified surfaces in 0.5 M HCLO₄ was studied by cyclic voltammetry. The corresponding results showed that the Pt/SWCNT/GC electrode exhibits more improved catalytical activity than the Pt/C/GC electrode.     

Pd/Pt二元合金电极的制备及氧还原性能

本文利用欠电位沉积亚单层的Cu及Pt置换取代Cu的方法, 制备了具有不同表面元素组成的Pd/Pt二元合金电极(用Pd/Ptx表示, x指欠电位沉积Cu-Pt置换取代Cu过程的次数),并对其表面元素组成、氧还原性能进行了表征. 在控制欠电位沉积Cu的下限电位恒定(0.34 V)的前提下, 表面Pt/Pd的元素组成比通过重复欠电位沉积Cu及Pt置换取代Cu的次数(1~5次)来可控地调变. 光电子能谱(XPS) 以及红外光谱实验表明,Pd/Ptx电极表层区的Pt：Pd元素组成比随着Pt沉积次数增加而增加, 对Pd/Pt4电极, 在电极表层区约2~3 nm内的Pt/Pd的原子比大约是1:4,而最表层裸露Pd原子的比例仍在20%以上。循环伏安结果显示, 随着Pt沉积次数的增加(1-5次), Pd/Ptx电极表面越不易被氧化。氧还原测试结果显示随着Pt沉积次数的增加(1~4次), Pd/Ptx二元金属电极的氧还原活性依次增加, 经过第3次沉积后其氧还原活性已优于纯Pt,而经4次以上沉积,其氧还原活性基本不变。在其它反应条件相同条件的前提下, Pd/Pt4电极上氧还原的半波电位与纯Pt相比右移约25 mV。结合本文与文献的实验结果,我们初步认为Pd/Ptx二元金属体系氧还原性能改善主要源自表层Pd原子导致其邻近的Pt原子上含氧物种吸附能的降低.     

铂电极上锑吸附原子对1,2-丙二醇电催化氧化性能的影响

运用电化学循环伏安(CV)和电化学原位石英晶体微天平(EQCM)研究了Pt电极表面不可逆吸附Sb原子的电化学特性以及Pt电极上Sb吸附原子对0.1mol·L-1H2SO4溶液中1,2 丙二醇电催化氧化性能的影响.研究发现,当扫描电位的上限Eu≤0.50V(SCE)时,Sb可以稳定地吸附在Pt电极表面,饱和覆盖度为0.34;通过控制电位扫描上限和扫描圈数剥离部份Sb可方便地得到Sbad的不同覆盖度;Pt电极表面Sb吸附原子能在较低的电位下吸附氧,可显著提高1,2 丙二醇电催化氧化活性.与Pt电极相比较,Sb饱和吸附原子修饰的Pt电极使1,2 丙二醇氧化的峰电流增加了近2倍.作者还从表面质量变化提供了吸附原子电催化作用的新数据.     

A Graphite‐Polyurethane Composite Electrode for the Analysis of Furosemide

A graphite‐polyurethane composite electrode has been used for the determination of furosemide, a antihypertensive drug, in pharmaceutical samples by anodic oxidation. Cyclic voltammetry and electrochemical impedance spectroscopy were used to characterize the electrooxidation process at +1.0 V vs. SCE over a wide pH range, with the result that no adsorption of analyte or products occurs, unlike at other carbon‐based electrode materials. Quantification was carried out using cyclic voltammetry, differential pulse voltammetry, and square‐wave voltammetry. Linear ranges were determined (up to 21 μmol L^?1 with cyclic voltammetry) as well as limits of detection (0.15 μmol L^?1 by differential pulse voltammetry). Four different types of commercial samples were successfully analyzed. Recovery tests were performed which agreed with those obtained by spectrophotometric evaluation. The advantages of this electrode material for repetitive analyzes, due to the fact that no electrode surface renewal is needed owing to the lack of adsorption, are highlighted.     

Structurally heterogeneous electrode films of polyacrylamide and acrylamide/vinylpyridine copolymeric gels: Mediation of ascorbic acid oxidation

The surface chemistry, i.e. adsorption and surface phase formation, on Rh, Ir, Pt and Au single-crystal electrodes in 0.5 M H₂SO₄ has been studied in the potential range between 0 and 4 V vs. a standard hydrogen electrode by X-ray photoelectron spectroscopy and cyclic voltammetry. Both methods gave complementary results which were interpreted as potential-dependent changes from physisorption of water to adsorption of hydroxyl groups, hydroxide film formation, and eventual growth of thick adlayers of oxyhydroxide (Rh, Ir and Au) or hydroxide (Pt) with increasing applied voltage.     

Anodic Stripping Voltammetric Detection of Arsenic(III) at Gold Nanoparticle‐Modified Glassy Carbon Electrodes Prepared by Electrodeposition in the Presence of Various Additives

The simple, fast and highly sensitive anodic stripping voltammetric detection of As(III) at a gold (Au) nanoparticle‐modified glassy carbon (GC) (nano‐Au/GC) electrode in HCl solution was extensively studied. The Au nanoparticles were electrodeposited onto GC electrode using chronocoulometric technique via a potential step from 1.1 to 0 V vs. Ag|AgCl|NaCl (sat.) in 0.5 M H₂SO₄ containing Na[AuCl₄] in the presence of KI, KBr, Na₂S and cysteine additives. Surfaces of the resulting nano‐Au/GC electrodes were characterized with cyclic voltammetry. The performances of the nano‐Au/GC electrodes, which were prepared using different concentrations of Na[AuCl₄] (0.05–0.5 mM) and KI additive (0.01–1.0 mM) at various deposition times (10–30 s), for the voltammetric detection of As(III) were examined. After the optimization, a high sensitivity of 0.32 mA cm^?2 μM^?1 and detection limit of 0.024 μM (1.8 ppb) were obtained using linear sweep voltammetry.     

Electrochemistry of triphenyltin acetate at a mercury-film glassy carbon electrode

The electrochemical behaviour of triphenyltin acetate was investigated by cyclic voltammetry, differential-pulse voltammetry and controlled potential electrolysis at a mercury-film glassy carbon electrode. Effects on the electrochemical response of the composition of supporting electrolytes, pH, electrode rotation speed and triphenyltin acetate concentration were determined. The electrochemical reduction of this compound was found to involve a preliminary adsorption process (E_peak ≈ ?0.7 V vs. SCE), the reduction of triphenyltin acetate to the triphenyltin radical (E_peak ≈ ?1.0 V) and reduction of the radical to the triphenyltin anion (E_peak ≈ ?1.4 V). A procedure for the determination of trace amounts of this compound by differential-pulse anodic stripping voltammetry in 50% (v/v) ethanol with 0.1 M acetic acid + 0.1 M ammonia solution was developed and applied to the analysis of a commercial powder formulation and water and fish samples. The limit of detection was 2.5 × 10^?9 M triphenyltin acetate.     

The Electrochemical Behavior and the Quantitative Determination of Nitrogen Dioxide at a Solid Polymer Electrolyte Supported Pt‐Au Electrode

The electrochemical behavior of NO₂ at Au/Nafion, Pt/Nafion and Pt‐Au/Nafion electrodes was investigated by using electrochemical and SEM methods, respectively. It was found that the Pt‐Au/Nafion electrode showed higher electrocatalytic activity than Pt/Nafion and Au/Nafion electrodes. The net current density of Au/Nafion electrode decayed significantly during the reaction, though it showed high initial value. Pt/Nafion and Pt‐Au/Nafion electrodes, on the contrary, showed good stability. A quantitative determination of NO₂ concentration was carried out at Pt‐Au/Nafion electrode and a satisfactory linear relationship was found for the NO₂ concentration in the range of 0–100 ppm.     

Electrochemical Determination of Transmembrane Protein Na+/K+‐ATPase and Its Cytoplasmic Loop C45

Electrochemistry of membrane proteins is complicated by the fact that the studied substances are poorly soluble or insoluble in aqueous environment. The solubilization of proteins using surfactants (detergents) affects the electrochemical analysis or even renders it impossible. In the present study, the electrochemistry of the transmembrane protein Na⁺/K⁺‐ATPase (NKA) and its water‐soluble isolated cytoplasmic loop C45 is described. The proteins were studied using adsorptive transfer cyclic voltammetry and square‐wave voltammetry on basal‐plane pyrolytic graphite electrode (PGE) as well as constant‐current chronopotentiometric stripping analysis on hanging mercury drop electrode (HMDE). The nonionic surfactant octaethylene glycol monododecyl ether (C₁₂E₈) was used for NKA solubilization. Under these conditions the oxidation currents of Tyr and Trp (peak Y: +0.55 V and peak W: +0.7 V, vs. Ag/AgCl/3 M KCl) and catalytic reduction currents (peak H: ?1.8 V) of NKA and C45 loop can be observed. Using the experimental procedures suggested in this study, we were able to investigate the oxidation, reduction and adsorption of NKA and C45 at femtomole level without the necessity of labeling by electroactive markers or techniques based on protein immobilization within the lipid bilayer attached to the electrode surface.     

Electrochemical Studies of Chemically Modified Nanometer‐Sized Electrodes

Self‐assembled monolayers (SAMs) of 4‐aminothiophenol (4‐ATP) has been successfully deposited onto nanometer‐sized gold (Au) electrodes. The cyclic voltammograms obtained on a 4‐ATP SAMs modified electrode show peaks and the peak height is proportional to the scan rate, which is similar to that on an electroactive SAMs modified macro electrode. The electrochemical behavior and mechanism of outer‐sphere electron transfer reaction on the 4‐ATP SAMs modified nanometer‐sized electrode has also been studied. The 4‐ATP SAMs modified electrode is further modified with platinum (Pt) nanoparticles. Electrochemical behaviors show that there is electrical communication between Pt nanoparticles and Au metal on the Pt nanoparticles/4‐ATP SAMs/Au electrode. However, scanning electron microscopic image shows that the Pt nanoparticles are not evenly covered the electrode.     

硝基苯在铜电极上的电还原特性研究

应用循环伏安法和线性扫描伏安法研究水溶液中硝基苯在铜电极上的电还原特性及其电还原为苯胺的中间步骤和反应机理.结果表明:铜电极上硝基苯的还原电位在-0.58V和-1.32V左右(vs.SCE),溶液的酸性和碱性均有益于该还原反应的发生;还原过程伴有反应物吸附现象,当硝基苯浓度较大时,还原过程受传质过程控制;随着厌氧程度的提高,还原速率加快.     

Mechanism of nitrate electroreduction on Pt(100)

Kinetics and mechanism of nitrate anion reduction on the Pt(100) electrode in perchloric and sulfuric acid solutions are studied. Analysis of the results of electrochemical measurements (combination of potentiostatic treatment and cyclic voltammetry) and the data of in situ IR spectroscopy allow suggesting the following scheme of the nitrate reduction process on Pt(100) differing from that in the literature. If the potential of 0.85 V is chosen as the starting potential for a clean flame-annealed electrode surface and negativegoing (cathodic) potential sweep is applied, then an NO adlayer with the coverage of about 0.5 monolayer is formed on Pt(100) in the nitrate solution already at 0.6 V. The further decrease in the potential results in NO reduction to hydroxylamine or/and ammonia, desorbing products vacate the adsorption sites for nitrate and hydrogen adatoms. At E < 0.1 V, adsorbed hydrogen is mostly present on the surface. During positive-going (anodic) potential sweep, the process of nitrate reduction starts after partial hydrogen desorption, the cathodic peak of nitrate reduction to hydroxylamine or ammonia is observed at 0.32 V on cyclic voltammograms. The process of nitrate anion reduction continues up to 0.7 V; at higher potentials, the surface redox process with participation of hydroxylamine or ammonia (the anodic peak at 0.78 V) and nitrate (the cathodic peak at 0.74 V is due to nitrate reduction to NO on the vacant adsorption sites) occurs.