Electrochemical Fabrication of Prussian Blue Nanocube‐decorated Electroreduced Graphene Oxide for Amperometric Sensing of NADH

In this study, Prussian blue (PB) film on the electroreduced graphene oxide (ERGO)‐modified Au electrode surface (ERGO/PB) is easily prepared by means of cyclic voltammetric technique in the mixture of K₃Fe(CN)₆ and FeCl₃. Its electrochemical behaviors for NADH biosensor are studied. The structural and morphological characters of modified electrode material are analyzed with using of XPS, XRD, Raman, EDS, and SEM techniques. ERGO/PB hybrid nanocomposite for NADH biosensor is exhibited to the higher catalytic effect (linear range from 1.0 to 100 μM, detection limit of 0.23 μM at S/N=3) compared to naked Au, ERGO‐modified Au, and PB‐modified Au electrodes. In addition to, ERGO/PB electrode was used to voltammetric and amperometric detection of H₂O₂. ERGO/PB electrodes also showed the same behavior as the NADH sensor. This ERGO/PB‐modified electrode supplied a simple, new, and low‐cost route for amperometric sensing of both NADH and H₂O₂.     

Electroanalytical Study of Prussian Blue Modified Glassy Carbon Paste Electrodes

Two types of glassy carbon (GC) powder (i.e., Sigradur K and Sigradur G) have been mixed with mineral oil to obtain glassy carbon paste electrodes (GCPE's). The electrochemical behavior of such electrodes at different percentages of glassy carbon has been evaluated with respect to the electrochemistry of ferricyanide as revealed with cyclic voltammetry and the best paste composition was chosen. GC was then modified with Prussian Blue (PB), mixed at different percentages with unmodified GC and with a fixed amount of mineral oil in order to obtain PB modified glassy carbon paste electrodes (PB‐GCPE's). PB‐GCPE's with different percentages of GC modified with PB (PB‐GC) were compared and the dependence on the amount of PB on their performances was evaluated by studying the parameters of cyclic voltammetry (i.e., current peak, ΔE_p, anodic and cathodic current ratio, charge density) and the amperometric response to H₂O₂. Data interpretation based on the GC surface area is presented. GCPE's with a selected amount of PB‐GC were then tested as H₂O₂ probes and all the analytical parameters together with the dependence on pH were evaluated. Some preliminary experiments with these electrodes assembled as glucose, lysine and lactate biosensors are also reported.     

Enhancement of the Electrochemical Performance of Prussian Blue Modified Electrode via Ionic Liquid Treatment

This article first reports the preparation of a Prussian blue (PB) modified electrode with improved electrochemical properties at the functionalized glass carbon electrode (GC) by imidazolium based ionic liquid. The molecular ionic liquid film on the GC electrode has been found to influence the electrodeposition of PB by a way of enhancement of voltammetric currents, suggesting efficient electrodepositon. Such efficient electrodeposition was caused by the static electric effect which existed between the positively charged imidazolium group on the electrode surface and the negative ferric‐ferricyanide in solution. Compared with the PB/GC electrode, the PB/[Bmim][Cl]/GC electrode showed much better electrochemical stability after successive potential cycling for 250 cycles. A comparative study on amperometric responses of both electrodes to reduce H₂O₂ was also investigated. PB/[Bmim][Cl]/GC electrode showed a better electrocatalytic performance to H₂O₂ with wider linear detection range and higher sensitivity than that at the electrode without [Bmim][Cl]. Furthermore, the kinetics for both electrodes was discussed. The PB/[Bmim][Cl]/GC electrode possessed a greater diffusion coefficient.     

Effect of Various Deposition Techniques,Electrode Materials and Posttreatment with Tetrabutylammonium and Tetrabutylphosphonium Salts on the Electrochemical Behavior and Stability of Various Prussian Blue Modified Electrodes

The effect of various deposition techniques, electrode materials and posttreatment with tetrabutylammonium and tetrabutylphosphonium salts on the electrochemical behavior and stability of various Prussian blue (PB) modified electrodes, namely PB modified glassy carbon electrodes, silicate‐film supported PB modified glassy carbon electrodes, PB‐doped silicate glassy carbon electrodes, PB modified carbon ceramic electrodes using electrochemical deposition and PB modified carbon ceramic electrodes using chemical deposition is reported. Cyclic voltammetry and amperometric measurements of hydrogen peroxide were performed in a flow injection system while the carrier phosphate buffer (pH 7.0) with a flow rate of 0.8 mL min^?1 was propelled into the electrochemical flow through cell housing the PB modified working electrode as well as an Ag|AgCl|0.1 M KCl reference and a Pt auxiliary electrode. The results showed that the deposition procedure, electrode material and posttreatment with additional chemicals can significantly alter the stability and electrochemical behavior of the PB film. Among the studied PB modified electrodes, those based on carbon ceramic electrodes modified with a film of electropolymerized PB showed the best electrochemical stability.     

Self‐Assembling of Hybrid Prussian Blue Units in Cinder Matrix: Characterization and Electrocatalysis

Industrial waste cinder (CFe*) has been utilized as a stable anchoring matrix for self‐assembling of Fe(CN)₆^3? as hybrid Prussian blue units (PB, *Fe³⁺Fe^II(CN)₆) on a screen‐printed carbon electrode (SPE) for efficient catalytic applications. The waste cinder was found to be a composite of calcium and iron silicates similar to glass matrix by X‐ray photoelectron spectroscopic (XPS) study. The hybrid PB formations were confirmed by both FT‐IR and electrochemical methods. Most importantly, the free iron (Fe*) ion bound to the non‐bridging oxygen terminals of the silicates was found to play a key role in the PB formation. The self‐assembled PB hybrid on the cinder‐modified screen‐printed electrodes (designated as PBCFe*‐SPE) improved linear detection range and sensitivity for H₂O₂ mediated oxidation than those obtained at a classical PB‐SPE in 0.1 M, pH 2 KCl/HCl base electrolyte at 0.0 V (vs. Ag/AgCl) by amperometric batch analysis.     

Galactose Oxidase/Prussian Blue Based Biosensors

This paper describes the development of an amperometric biosensor based on galactose oxidase (GAOx) immobilization within a laponite clay film deposited on Carbon Screen‐Printed Electrodes modified by electrodeposited Prussian Blue and coated with poly‐(O‐phenylenediamine) (PPD/PB/CSPEs). Amperometric performances of GAOx@laponite/PPD/PB/CSPEs bioelectrodes were determined using several GAOx substrates. Using these modified electrodes the reduction of enzymatically generated hydrogen peroxide was performed at ?0.2 V vs. Ag‐AgCl. In an initial attempt, E.Coli transketolase activity on its immobilized form was followed using a bienzymatic GAOx‐TK biosensor.     

Functionalization of Single‐Walled Carbon Nanotubes with Cubic Prussian Blue and Its Application for Amperometric Sensing

In this work, we synthesized electroactive cubic Prussian blue (PB) modified single‐walled carbon nanotubes (SWNTs) nanocomposites using the mixture solution of ferric‐(III) chloride and potassium ferricyanide under ambient conditions. The successful fabrication of the PB‐SWNTs nanocomposites was confirmed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV‐vis absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy, and cyclic voltammetry (CV). PB nanocrystallites are observed to be finely attached on the SWNTs sidewalls in which the SWNTs not only act as a carrier of PB nanocrystallites but also as Fe(III)‐reducer. The electrochemical properties of PB‐SWNTs nanocomposites were also investigated. Using the electrodeposition technique, a thin film of PB‐SWNTs/chitosan nanocomposites was prepared onto glassy carbon electrode (GCE) for the construction of a H₂O₂ sensor. PB‐SWNTs/chitosan nanocomposites film shows enhanced electrocatalytic activity towards the reduction of H₂O₂ and the amperometric responses show a linear dependence on the concentration of H₂O₂ in a range of 0.5–27.5 mM and a low detection limit of 10 nM at the signal‐to‐noise ratio of 3. The time required to reach the 95% steady state response was less than 2 s. CV studies demonstrate that the modified electrode has outstanding stability. In addition, a glucose biosensor is further developed through the simple one‐step electrodeposition method. The observed wide concentration range, high stability and high reproducibility of the PB‐SWNTs/chitosan nanocomposites film make them promising for the reliable and durable detection of H₂O₂ and glucose.     

Physicochemical Characteristics of Polypyrrole/(Glucose oxidase)/(Prussian Blue)‐based Biosensor Modified with Ni‐ and Co‐Hexacyanoferrates

In this work, three types of electrodes suitable for amperometric glucose biosensors were designed. One type of electrode was based on bio‐selective layer of polypyrrole/(glucose oxidase)/(Prussian Blue) (Ppy/GOx/PB) and it was used as a control electrode regarding to which electrochemical properties of two other types of electrodes were compared. During the formation of Prussian blue layers graphite electrodes were additionally modified by Ni‐hexacyanoferrate (NiHCF) and by Co‐hexacyanoferrate (CoHCF) in order to design Ppy/GOx/PB‐NiHCF and Ppy/GOx/PB‐CoHCF electrodes, respectively. Some physicochemical characteristics of all three types of electrodes were evaluated and compared. The Ppy/GOx/PB‐NiHCF electrode showed wider linear range of the calibration curve than Ppy/GOx/PB and Ppy/GOx/PB‐CoHCF electrodes. The effect of temperature on analytical performance of the Ppy/GOx/PB‐NiHCF based biosensor has been evaluated and activation energy of enzyme catalysed reaction has been calculated within the temperature range of 15 °C to 30 °C.     

Development of an Enzymeless/Mediatorless Glucose Sensor Using Ruthenium Oxide‐Prussian Blue Combinative Analogue

Presented in this work is the first step towards an enzymeless/mediatorless glucose sensor. We first observed remarkable electrocatalytic oxidation of glucose using combinative ruthenium oxide (RuOx)‐Prussian blue (PB) analogues (designated as mvRuOx‐RuCN, mv: mixed valent) at ca. 1.1 V (vs. Ag/AgCl) in acidic media (pH 2 Na₂SO₄/H₂SO₄). Individual RuOx and PB analogs failed to give any such catalytic response. A high ruthenium oxidation state (i.e., oxy/hydroxy‐Ru^VII, E°≈1.4 V vs. RHE), normally occurring in strong alkaline conditions at RuOx‐based electrodes, was electrogenerated and stabilized (without any conventional disproportionation reaction) in the mvRuOx‐RuCN matrix for glucose catalysis. Detail X‐ray photoelectron spectroscopic studies can fully support the observation. The catalyst was chemically modified onto a disposable screen‐printed carbon electrode and employed for the amperometric detection of glucose via flow injection analysis (FIA). This system has a linear detection range of 0.3–20 mM with a detection limit and sensitivity of 40 μM (S/N=3) and 6.2 μA/(mM cm²), respectively, for glucose. Further steps towards the elimination of interference and the extendibility to neutral pHs were addressed.     

Use of Screen‐printed Electrodes Modified by Prussian Blue and Analogues in Sensing of Cysteine

The utilisation of screen‐printing technology allows for a mass scalable approach for the production of electrochemical screen‐printed electrodes (SPEs) and the presence of a redox mediator can add new possibilities to the electrochemical properties of the SPEs. Among the materials used as redox mediators, cyanidoferrates polymers can be used for electro‐oxidation of cysteine. In this work, two monomers, namely, [Fe(CN)₆]⁴⁻ and [Fe(CN)₅NH₃]³⁻ were used to produce Prussian blue (PB) and Prussian blue‐Ammine (PB‐Ammine), respectively. In addition, two modification methods were compared, firstly via a drop‐casting and secondly by the incorporation of these materials into a printable ink. The SPE modified by PB‐Ammine (drop‐casting) exhibits the highest electroactive area, however the highest heterogeneous rate constant was found with the SPE modified by PB‐Ammine that was incorporated into the ink. The highest value of the constant of electro‐oxidation of cysteine and lowest limit of detection was also observed in the SPE modified by PB incorporated into the ink. These studies suggest that the electrocatalytic properties of SPE modified by PB and PB‐Ammine are dependent upon the availability of Fe³⁺ catalytic sites and the increased kinetics of the chemical reaction between the catalytic sites and the analyte.     

Laccase Biosensor Based on N‐Succinimidyl‐3‐Thiopropionate‐Functionalized Gold Electrodes

A laccase biosensor, in which the enzyme was immobilized on N‐succinimidyl‐3‐thiopropionate (NSTP)‐modified gold electrodes, is reported. Two different approaches for the preparation of N‐succinimidyl‐terminated monolayers were evaluated: a) activation of a preformed 3‐mercaptopropionic acid (MPA) SAM by reaction with 1‐(3‐dimethylaminopropyl)‐ 3‐ethylcarbodiimide (EDC) and N‐hydroxysulfosuccinimide (NHS); b) assembling of dithiobisuccinimidyl propionate (DTSP). NSTP‐modified electrodes were characterized by cyclic voltammetry and electrochemical impedance spectroscopy. Biosensors prepared by covalent binding of the enzyme and by cross‐linking with glutaraldehyde atop NSTP‐modified electrodes were compared in terms of sensitivity and operational range for caffeic acid. A much better analytical performance was found using the latter approach. Variables affecting the amperometric detection (enzyme loading, pH and applied potential) were optimized. The operational stability and characteristics of functioning of the laccase biosensor in terms of repeatability of the amperometric measurements, reproducibility with different biosensors and useful lifetime, were evaluated. The kinetic parameters of the enzyme reactions and the analytical characteristics of the corresponding calibration plots were calculated for eight phenolic compounds. Limits of detection of 0.07 μM, 0.05 μM and 0.09 μM were obtained for caffeic acid, catechol and 3,4‐dihydroxyphenylacetic acid (DOPAC), respectively. The practical usefulness of the developed biosensor was evaluated by estimating the “pool” of phenolic compounds in olive oil mill wastewaters (OMW).     

Amperometric Biosensor for Hydrogen Peroxide,Using Supramolecularly Immobilized Horseradish Peroxidase on the β‐Cyclodextrin‐Coated Gold Electrode

Horseradish peroxidase, previously modified with 1‐adamantane moieties, was supramolecularly immobilized on gold electrodes coated with perthiolated β‐cyclodextrin. The functionalized electrode was employed for the construction of an amperometric biosensor device for hydrogen peroxide using 1 mM hydroquinone as electrochemical mediator. The biosensor exhibited a fast amperometric response (6 s) and a good linear response toward H₂O₂ concentration between 12 μM and 450 μM. The biosensor showed a sensitivity of 1.02 mA/M cm², and a very low detection limit of 5 μM. The electrode retained 97% of its initial electrocatalytic activity after 30 days of storage at 4 ⁰C in 50 mM sodium phosphate buffer, pH 7.0.     

Functionalization of graphene with Prussian blue and its application for amperometric sensing of H2O2

As a two-dimensional carbon material with high surface area and conductivity, graphene shows great promise for designing composite nanomaterials to achieve high-performance electrochemical devices. In this work, we prepared graphene-based nanocomposite material by electrochemically depositing Prussian blue (PB) nanoparticles on the surface of graphene. Fourier transform infrared spectra, SEM, and cyclic voltammetry were used to characterize the successful immobilization of PB. Compared with PB films and graphene sheets, the PB–graphene composite films showed the largest current response to the reduction of H₂O₂, probably due to the synergistic effects between graphene sheets and PB nanoparticles. Therefore, a fast and highly sensitive amperometric sensor for H₂O₂ was obtained with a detection sensitivity of 1.6 μA μM^?1 H₂O₂ per cm² and a linear response range of 50～5,000 μM. The detection limit of H₂O₂ was 20 nM at a signal-to-noise ratio of 3. These obtained results are much better than those reported for carbon nanotubes-based amperometric sensors.     

Electrocatalysis of Puerarin on a Nano-CeO2/MWCNTs Composite Modified Electrode and Its Determination in Pharmaceutical Preparations

A good route for the fabrication of CeO₂ nanoparticles (nano‐CeO₂)/multi‐walled carbon nanotubes (MWCNTs) modified glassy carbon electrodes (GCE) was proposed. MWCNTs are used to immobilize nano‐CeO₂. What′s more, with the addition of the MWCNTs, the agglomeration level of CeO₂ nanoparticles can be reduced, the extremely large surface area can be obtained and the electron transfer rate can be increased. The morphological characterization of nano‐CeO₂/MWCNTs was examined by scanning electron microscopy (SEM). The performances of the nano‐CeO₂/MWCNTs/GCE were characterized with cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and typical amperometric response (i‐t). The potential utility of the constructed electrodes was demonstrated by applying them to the analytical determination of puerarin concentration. The catalytic oxidation of puerarin has a better result on nano‐CeO₂/MWCNTs/GCE because of the synergistic effect of nano‐CeO₂ and MWCNTs. An optimized limit of detection of 8.0×10^?9 mol/L was obtained at a signal‐to‐noise ratio of 3 and with a fast response time (within 3 s). Additionally, the nano‐CeO₂/MWCNTs/GCE exhibited a wide linear range from 0.04 to 6.0 μmol/L and high sensitivity.     

A Facile Preparation of H2O2 Sensors Using Layer‐by‐Layer Deposited Thin Films Composed of Poly(ethyleneimine) and Carboxymethyl Cellulose as Matrices for Immobilizing Hemin

A layer‐by‐layer (LbL) thin film composed of poly(ethyleneimine) (PEI) and carboxymethyl cellulose (CMC) was prepared on the surface of a gold (Au) disk electrode and the LbL layer was impregnated with hemin to fabricate amperometric hydrogen peroxide (H₂O₂) sensors. Hemin can be easily immobilized in the LbL layer by immersing the LbL film‐coated electrode in the hemin solution. The hemin‐modified electrode thus prepared exhibited an amperometric response to H₂O₂ on the basis of the electrochemical reduction catalyzed by hemin. The output current of the hemin‐modified electrode depended on the concentration of H₂O₂ over the range of 0.005–1.0 mM. Thus, the LbL film composed of PEI and CMC was found to be an excellent material for the facile preparation of hemin‐based H₂O₂ sensors.     

Electrocatalytic Activity of Nanohybrids Based on Carbon Nanomaterials and MFe2O4 (M=Co,Mn) towards the Reduction of Hydrogen Peroxide

We report the advantages of hybrid nanomaterials prepared with electrogenerated ferrites (MFe₂O₄; M: Co, Mn) and multi‐walled carbon nanotubes (MWCNTs) or thermally reduced graphene oxide (TRGO) on the electro‐reduction of hydrogen peroxide. Glassy carbon electrodes (GCE) modified with these hybrid nanomaterials dispersed in Nafion/isopropanol demonstrated a clear synergism on the catalytic reduction of reduction of hydrogen peroxide at pH 13.00. The intimate interaction between MFe₂O₄ and carbon nanomaterials allowed a better electronic transfer and a facilitated regeneration of M²⁺ at the carbon nanomaterials, reducing the charge transfer resistances for hydrogen peroxide reduction and increasing the sensitivities of the amperometric response.     

A Reagentless Amperometric Immunosensor for Alpha‐Fetoprotein Based on Gold Nanoparticles/TiO2 Colloids/Prussian Blue Modified Platinum Electrode

A novel reagentless amperometric immunosensor for the determination of alpha‐fetoprotein (AFP) was prepared by immobilizing TiO₂ colloids on Prussian blue (PB) modified platinum electrode, which yielded a positively charged interface with strong adsorption to deposit gold nanoparticles for immobilization of alpha‐fetoprotein antibody (anti‐AFP). The factors influencing the performance of the proposed immunosensors were studied in detail. Under the optimized conditions, cyclic voltammograms determination of AFP showed a specific response in two concentration ranges from 3.0 to 30.0 ng/mL and from 30.0 to 300.0 ng/mL with a detection limit of 1.0 ng/mL at a signal‐to‐noise ratio of 3. The proposed immunosensor exhibited high selectivity, good reproducibility, long‐term stability (>2 months) and good repeatability.     

Amperometric Detection and Quantification of 8‐Hydroxy‐2′‐deoxyguanosine (8‐OHdG) Using Dendrimer Modified Electrodes

8‐Hydroxy‐2′‐deoxyguanosine (8‐OHdG) detection by high performance liquid chromatography (HPLC) with amperometric detection was studied using a Au electrode modified with different dendrimer based thin films. Gold electrode is thiol‐modified, forming self‐assembled monolayers on which different generation PAMAM dendrimers with terminal functional groups ? COOH and ? NH₂ have been attached using peptidic bonds. Results obtained in synthetic samples show low limits of detection and quantification for 8‐OHdG (1.2×10^?9 and 3.7×10^?9 M respectively), with matrix interference elimination, thus avoiding sample pretreatment. Best results are obtained with electrodes modified with aliphatic amino thiols and 3.5 and 4.5 generation carboxylated dendrimers (Au/AET/DG^3.5 and Au/AET/DG^4.5), demonstrating that these materials constitute a good alternative for 8‐OHdG determination in biological fluids.     

Amperometric Glucose Biosensors Based on Integration of Glucose Oxidase onto Prussian Blue/Carbon Nanotubes Nanocomposite Electrodes

Nanosized Prussian blue (PB) particles were synthesized with a chemical reduction method and then the PB nanoparticles were assembled on the surface of multiwall carbon nanotubes modified glassy carbon electrode (PB/MWNTs/GCE). The results showed that the PB/MWNTs nanocomposite exhibits a remarkably improved catalytic activity towards the reduction of hydrogen peroxide. Glucose oxidase (GOD) was immobilized on the PB/MWNTs platform by an electrochemically polymerized o‐phenylenediamine (OPD) film to construct an amperometric glucose biosensor. The biosensor exhibited a wide linear response up to 8 mM with a low detection limit of 12.7 μM (S/N=3). The Michaelis–Menten constant K_m and the maximum current i_max of the biosensor were 18.0 mM and 4.68 μA, respectively. The selectivity and stability of the biosensor were also investigated.     

Amperometric Magnetoimmunosensors for Direct Determination of D‐Dimer in Human Serum

Two different D‐dimer disposable amperometric immunosensing designs based on indirect competitive or sandwich formats and the use of carboxylic acid‐modified magnetic beads (COOH‐MBs) and screen‐printed carbon electrodes (SPCEs) have been developed and compared. In both approaches, the resulting modified MBs were magnetically captured on the surface of a SPCE which was used as the transducer for the electrochemical detection at ?0.20 V upon addition of H₂O₂, and hydroquinone (HQ). Both configurations exhibited linear ranges of clinical usefulness and detection limits quite below the clinical threshold (0.5 µg mL^?1 D‐dimer). The sandwich configuration has been successfully tested with serum samples.