Amperometric Glucose Biosensor Based on the Deposition of Copper and Glucose Oxidase onto Glassy Carbon Transducer

ABSTRACT

The performance of a first generation glucose amperometric biosensor based on the entrapment of glucose oxidase (GOx) within a net of copper electrodeposited onto activated glassy carbon electrode, is described. The copper electrodeposited offers an efficient electrocatalytic activity towards the reduction of enzymatically-liberated hydrogen peroxide, allowing for a fast and sensitive glucose quantification. The influence of the electrodeposition conditions (pH, potential, time, copper salt and enzyme concentrations) on the response of the bioelectrode was evaluated from the amperometric signals of hydrogen peroxide and glucose. The combination of copper electrodeposition with a nation membrane allows an excellent selectivity towards easily oxidizable compounds such as uric and ascorbic acids at an operating potential of -0.050 V. The response is linear up to 2.0 × 10^?2 M glucose, the detection limit being 1.2 × 10^?3 M.     

Amperometric Glucose Biosensors Based on Glassy Carbon and SWCNT‐Modified Glassy Carbon Electrodes

Different carbonaceous materials, such as single‐walled carbon nanotubes (SWCNTs) and glassy carbon submitted to an electrochemical activation at +1.80 V (vs. SCE) for 900 s, have been used with the aim of comparing their performances in the development of enzyme electrodes. Commercial SWCNTs have been pretreated with 2.2 M HNO₃ for 20 h prior to use. The utility of activated GC as promising material for amperometric oxidase‐based biosensors has been confirmed. With glucose oxidase (GOx) as a model enzyme, glucose was efficiently detected up to 1 mM without the use of a mediator. Both electrodes operated in stirred solutions of 0.1 M phosphate buffer (pH 5.5), containing dissolved oxygen, at a potential of ?0.40 V vs. SCE. Although the performances of the two carbonaceous materials were comparable, the biosensors based on activated GC were characterized by a practically unchanged response 40 days after the fabrication, a better signal to noise ratio, and a little worse sensitivity. In addition, the preparation procedure of such biosensors was more simple, rapid and reproducible.     

Disposable Screen‐Printed Carbon Electrodes for Dual Electrochemiluminescence/Amperometric Detection: Sequential Injection Analysis of Oxalate

This work describes the development and application of an electrochemical cell specifically designed for disposable screen printed carbon electrodes (SPCE) suitable for simultaneous electrochemiluminescence (ECL) and amperometric detection in sequential injection analysis. The flow system with facility for photomultiplier tube via a fiber optic facing the SPCE is user‐friendly and makes the detection process very easy to operate. Instead of the need to constant deliver the chemiluminescence (CL) reagents to the reaction zone, sequential injection analysis allows a considerable reduction in the consumption of the sample and expensive CL reagents (such as Ru(bpy) salts). The utility of the analyzer was demonstrated for the detection of oxalate based on the ECL reaction with Ru(bpy) . Under optimized conditions, in the presence of 100 μM Ru(bpy) , the linear ranges of peak current and ECL light intensity for oxalate distinctly varied from 10 μM to 5 mM and 0.1 μM to 100 μM, respectively. In other words, the linear detection can be covered over a four‐order range with the combination of these two signals.     

基于立方体纳米氧化亚铜修饰的安培型葡萄糖生物传感器的制备及性能研究

将合成的立方体纳米氧化亚铜用于修饰玻碳电极,在其上固定葡萄糖氧化酶,构建了高灵敏的安培型葡萄糖生物传感器.采用X射线衍射(X RD)、扫描电镜(SEM)对合成的立方体纳米氧化亚铜及其修饰电极进行了表征.结果表明,合成的纳米氧化亚铜为均匀的立方体形状.采用循环伏安法(CV)、交流阻抗谱(EIS)、差分脉冲伏安法(DPV)及计时电流法(CA)考察了修饰电极的电化学行为.在含0.1 mmol/L葡萄糖的磷酸盐缓冲溶液(pH 7.4)中研究了立方体纳米氧化亚铜修饰电极的循环伏安(CV)响应,实验结果表明,此修饰电极对葡萄糖显示出良好的电催化性能.DPV响应电流与葡萄糖的浓度在5.0×10-6 ～4.0× 10-3mol/L范围内呈良好的线性关系,线性相关系数R2=0.9983,检出限为6.8×10-7 mol/L(S/N=3).CA实验结果表明,尿酸、抗坏血酸、D-果糖对传感器不产生干扰.本传感器具有较好的重现性和稳定性,可用于实际样品中葡萄糖的检测.     

Reagentless Glucose Biosensor Based on the Direct Electrochemistry of Glucose Oxidase on Carbon Nanotube‐Modified Electrodes

The direct electrochemistry of glucose oxidase (GOD) was revealed at a carbon nanotube (CNT)‐modified glassy carbon electrode, where the enzyme was immobilized with a chitosan film containing gold nanoparticles. The immobilized GOD displays a pair of redox peaks in pH 7.4 phosphate buffer solutions (PBS) with the formal potential of about ?455 mV (vs. Ag/AgCl) and shows a surface‐controlled electrode process. Bioactivity remains good, along with effective catalysis of the reduction of oxygen. In the presence of dissolved oxygen, the reduction peak current decreased gradually with the addition of glucose, which could be used for reagentless detection of glucose with a linear range from 0.04 to 1.0 mM. The proposed glucose biosensor exhibited high sensitivity, good stability and reproducibility, and was also insensitive to common interferences such as ascorbic and uric acid. The excellent performance of the reagentless biosensor is attributed to the effective enhancement of electron transfer between enzyme and electrode surface by CNTs, and the biocompatible environment that the chitosan film containing gold nanoparticles provides for immobilized GOD.     

Amperometric Glucose Biosensor Based on Platinum Nanoparticles Combined Aligned Carbon Nanotubes Electrode

A sensitive amperometric glucose biosensor based on platinum nanoparticles (PtNPs) combined aligned carbon nanotubes (ACNTs) electrode was investigated. PtNPs which can enhance the electrocatalytic activity of the electrode for electrooxidating hydrogen peroxide by enzymatic reaction were electrocrystallized on 4‐aminobenzene monolayer‐grafted ACNTs electrode by potential‐step method. These PtNPs combined ACNTs' (PtNPs/ACNTs) surfaces were characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The highly dispersed PtNPs on ACNTs can be obtained. The enzyme electrode exhibits excellent response performance to glucose with linear range from 1×10^?5–7×10^?3 mol L^?1 and fast response time within 5 s. Furthermore, this glucose biosensor also has good reproducibility. It is demonstrated that the PtNPs/ACNTs electrode with high electrocatalytic activity is a suitable basic electrode for preparing enzyme electrodes.     

Electrochemical Determination of Pyrogallol at Conducting Poly(3,4‐ethylenedioxythiophene) Film‐Modified Screen‐Printed Carbon Electrodes

The electrochemical oxidation of pyrogallol at electrogenerated poly(3,4‐ethylenedioxythiophene) (PEDOT) film‐modified screen‐printed carbon electrodes (SPCE) was investigated. The voltammetric peak for the oxidation of pyrogallol in a pH 7 buffer solution at the modified electrode occurred at 0.13 V, much lower than the bare SPCE and preanodized SPCE. The experimental parameters, including electropolymerization conditions, solution pH values and applied potentials were optimized to improve the voltammetric responses. A linear calibration plot, based on flow‐injection amperometry, was obtained for 1–1000 µM pyrogallol, and a slope of 0.030 µA/µM was obtained. The detection limit (S/N=3) was 0.63 µM.     

Flow Injection Analysis of Aluminum Chlorohydrate in Antiperspirant Deodorants Using a Built‐in Three‐in‐one Screen‐Printed Silver Electrode

A screen‐printed silver strip with a built‐in three‐in‐one electrode (SPAgE) configuration of Ag‐working, Ag‐counter and Ag/Ag_xO (silver oxides) pseudoreference electrodes has been developed for sensitive and selective electrochemical flow injection analysis (FIA) of aluminum chlorohydrate (ACH) present in antiperspirants, through the free Cl^? ion liberated from ACH in aqueous medium, as a redox signal at Ag‐working electrode in pH 6 phosphate buffer solution (PBS). The solution phase and instrumental parameters were systematically optimized. The calibration graph was linear in the window 1–200 ppm concentration of ACH and the lowest detection limit (S/N=3) was 295 ppb with a slope of 0.0989 μA/ppm and regression coefficient of 0.998. Calculated relative standard deviation (RSD) values for the detection of 5 and 50 ppm ACH by this method are 2.21 % and 2.16 %, respectively. Four different antiperspirant deodorants real samples with and without ACH content were successfully analyzed and the detected values obtained were found to be in good agreement with the product labeled values.     

Amperometric Biosensor for Choline Based on Gold Screen‐Printed Electrode Modified with Electrochemically‐Deposited Silica Biocomposite

A mediator‐free choline biosensor was developed using the electrochemically assisted sol‐gel deposition on gold screen‐printed electrodes. The addition of 12 mM of cationic surfactant CTAB in silica sol allowed enhancing the stability of the sensor. The modified electrode demonstrated catalytic activity and stable amperometric response to choline for over 3 weeks of exploitation with the sensitivity of 6 µA mM^?1 and LOD of 6 µM. The interference of ascorbic acid was reduced by pretreating the analyzed solution with MnO₂ powder. The application of the sensor with the purpose of identifying choline in the baby milk demonstrated satisfactory metrological characteristics.     

基于Nafion/碳纳米粒子修饰的葡萄糖传感器

采用滴涂法制备了Nafion/碳纳米粒子复合物修饰玻碳电极,该电极对H2O2具有良好的电催化氧化性能。还利用滴涂法制备了Nafion/碳纳米粒子复合物包裹的葡萄糖酶电化学生物传感器,该生物传感器对葡萄糖有着良好的电催化作用。应用该传感器对葡萄糖进行了检测,检测线性范围为2.0×10-6～6.0×10-3mol/L,检出限为1.6×10-6mol/L(S/N=3),实验结果表明该传感器具有良好的稳定性、重现性和抗干扰能力。对小鼠血清样品中的葡萄糖进行检测,结果令人满意。     

Sensitive Determination of Nitrofurantoin by Flow Injection Analysis Using Carbon Nanofiber Screen Printed Electrodes

In this work, a new method to quantify nitrofurantoin in aqueous media using a flow injection system connected to commercially available screen‐printed carbon nanofibers was developed. A pretreatment of the screen‐printed carbon nanofibers electrode with Britton? Robinson buffer/N,N‐dimethylformamide was applied to enhance the nitrofurantoin peak current signal in one step. The developed method was demonstrated to be sensible, reproducible, easy, and inexpensive. With a low detection limit, it is applicable to real samples. The results indicate that it is highly applicable for the detection of nitrofurantoin in several matrices. When urine samples without any pretreatment were analyzed, the method proved reproducible and sensible and had a low detection limit. The use of screen‐printed electrodes has advantages over other modified electrodes as a glassy carbon due to its versatility.     

Amperometric Glucose Biosensor Based on Pt‐Pd Nanoparticles Supported by Reduced Graphene Oxide and Integrated with Glucose Oxidase

A novel glucose biosensor was developed based on the immobilization of glucose oxidase (GOx) on reduced graphene oxide incorporated with electrochemically deposited platinum and palladium nanoparticles (PtPdNPs). Reduced graphene oxide (RGO) was more hybridized by chemical and heat treatment. Bimetallic nanoparticles were deposited electrochemically on the RGO surface for potential application of the Pd? Pt alloy in biosensor preparation. The as‐prepared hybrid electrode exhibited high electrocatalytic activities toward H₂O₂, with a wide linear response range from 0.5 to 8 mM (R²=0.997) and high sensitivity of 814×10^?6 A/mMcm². Furthermore, glucose oxidase with active material was integrated by a simple casting method on the RGO/PdPtNPs surface. The as‐prepared biosensor showed good amperometric response to glucose in the linear range from 2 mM to 12 mM, with a sensitivity of 24×10^?6 A/mMcm², a low detection limit of 0.001 mM, and a short response time (5 s). Moreover, the effect of interference materials, reproducibility and the stability of the sensor were also investigated.     

Prussian Blue Modified Amperometric Hg2+ Ion Biosensor Based on Glucose Oxidase Inhibition

In this research a Hg²⁺ ion biosensor was developed by combining Prussian blue (PB) with glucose oxidase (GOx) – an enzyme that can be inhibited by Hg²⁺ ions. An application of PB in the design of Hg²⁺ ion biosensor enabled detecting changes in hydrogen peroxide reduction current at low operational potential of 0.2 vs Ag|AgCl,KCl_sat. The described Hg²⁺ ion biosensor exhibited wide linear range from 27 μM to 247 μM of Hg²⁺ and higher maximal detectable concentration of Hg²⁺ than other GOx inhibition-based biosensors, making it convenient for the analysis of samples with high concentration of Hg²⁺ ions.     

Minimization of Interferences in Flow Injection Amperometric Glucose Biosensor Based on Oxidation of Enzymatically‐produced H2O2

One of the major problems in amperometric biosensors based on detection of H₂O₂ produced by enzymatic reaction between oxidase enzymes and substrate is the interference of redox active compounds such as ascorbic acid (AA), dopamine (DA) and uric acid (UA). To minimize these interferences, sodium bismuthate was used for the first time as an insoluble pre‐oxidant in the flow injection (FI) amperometric glucose biosensor at a Glucose oxidase (GOx) immobilized Pt/Pd bimetallic modified pre‐anodized pencil graphite electrode (p.PGE). In this context, these interfering compounds were injected into a flow injection analysis (FIA) system using an injector which was filled with NaBiO₃. Thus, these interferents were converted into their redox inactive oxidized forms before reaching the electrode in the flow cell. While glucose was not influenced by the pre‐oxidant in the injector, the huge oxidation peak currents of the interferents decreased significantly in the biosensor. FI amperometric current time curves showed that the AA, DA and UA were minimized by 96 %, 86 %, and 98 % respectively, in the presence of an equivalent concentration of interferences in a 1.0 mM glucose solution. The proposed FI amperometric glucose biosensor exhibits a wide linear range (0.01–10 mM, R²=0.9994) with a detection limit of 2.4×10^?3 mM. Glucose levels in the artificial serum and two real samples were successfully determined using the fabricated FI amperometric biosensor.     

Fabrication of a Highly Sensitive Glucose Biosensor Based on Immobilization of Osmium Complex and Glucose Oxidase onto Carbon Nanotubes Modified Electrode

In this research a novel osmium complex was used as electrocatalyst for electroreduction of oxygen and H₂O₂ in physiological pH solutions. Electroless deposition at a short period of time (60 s), was used for strong and irreversible adsorption of 1,4,8,12‐tetraazacyclotetradecane osmium(III) chloride (Os(III)LCl₂) ClO₄ onto single‐walled carbon nanotubes (SWCNTs) modified GC electrode. The modified electrode shows a pair of well defined and reversible redox couple, Os(IV)/Os(III) at wide pH range (1–8). The glucose biosensor was fabricated by covering a thin film of glucose oxidase onto CNTs/Os‐complex modified electrode. The biosensor can be used successfully for selective detection of glucose based on the decreasing of cathodic peak current of oxygen. The fabricated biosensor shows high sensitivity, 826.3 nA μM^?1cm^?2, low detection limit, 56 nM, fast response time <3 s and wide calibration range 1.0 μM–1.0 mM. The biosensor has been successfully applied to determination of glucose in human plasma. Because of relative low applied potential, the interference from electroactive existing species was minimized, which improved the selectivity of the biosensor. The apparent Michaelis‐Menten constant of GOx on the nanocomposite, 0.91 mM, exhibits excellent bioelectrocatalytic activity of immobilized enzyme toward glucose oxidation. Excellent electrochemical reversibility, high stability, technically simple and possibility of preparation at short period of time are of great advantages of this glucose biosensor.     

Development of Amperometric Glucose Biosensor Based on Reconstitution of Glucose Oxidase on Polymeric 3‐Aminophenyl Boronic Acid Monolayer

An amperometric biosensor for determining glucose based on deflavination of the enzyme glucose oxidase and subsequent reconstitution of the apo‐protein with a complexed flavin adenine dinucleotide (FAD) monolayer is described. The GOx‐reconstituted electrode exhibited excellent electrocatalytic activities towards the reduction and oxidation of hydrogen peroxide as well. The prepared biosensor showed an excellent performance for glucose at +0.5 V with a high sensitivity (5.94 μA/mM) and relatively good response time (～12 s) in a wide concentration range of 1–17 mM (correlation coefficient of 0.9998). The applicability to blood analysis was also evaluated.     

Nafion—四硫富瓦烯修饰蜡浸石墨电极的葡萄糖传感器

本文用四硫富瓦烯（ＴＴＦ）作为酶与电极之间的电子传递体，通过牛血清蛋白和戊二醛交联剂，把葡萄糖化氧化酶固定在Ｎａｆｉｏｎ－ＴＴＦ修饰石墨电极上，最后在电极修饰一层Ｎａｆｉｏｎ膜，制备成葡萄糖传感器。Ｎａｆｉｏｎ膜不仅能防止四硫富瓦燃流失，而且能氢抗坏血酸，尿酸等电活生物质阻挡在电极外，防止其干扰，同时具有防污性能。通过实验表明ＴＴＦ＾＋，ＴＴＴ＾２＾＋都能够氧化葡萄糖氧化酶中的辅酶（ＦＡＤＨ２）。     

Screen‐Printed Electrodes for Amperometric Determination of Iodide

An amperometric method for the determination of iodide ions has been developed using disposable, screen‐printed electrodes. The used sensors have a gold, graphite and platinum working electrodes with an area of about 7 mm². Calibration curves exhibit a linear relationship between the electrode response and the iodide concentration up to 3.00 mM. The correlation coefficients for all calibration curves varied from 0.988 to 0.998. The relative standard deviations were equal to or less than 5.26 % (n=5). The lowest iodide concentration measured was 100 µM.     

Biosensor Based on Self‐Assembling Glucose Oxidase and Dendrimer‐Encapsulated Pt Nanoparticles on Carbon Nanotubes for Glucose Detection

A novel amperometric glucose biosensor based on layer‐by‐layer (LbL) electrostatic adsorption of glucose oxidase (GOx) and dendrimer‐encapsulated Pt nanoparticles (Pt‐DENs) on multiwalled carbon nanotubes (CNTs) was described. Anionic GOx was immobilized on the negatively charged CNTs surface by alternatively assembling a cationic Pt‐DENs layer and an anionic GOx layer. Transmission electron microscopy images and ζ‐potentials proved the formation of layer‐by‐layer nanostructures on carboxyl‐functionalized CNTs. LbL technique provided a favorable microenvironment to keep the bioactivity of GOx and prevent enzyme molecule leakage. The excellent electrocatalytic activity of CNTs and Pt‐DENs toward H₂O₂ and special three‐dimensional structure of the enzyme electrode resulted in good characteristics such as a low detection limit of 2.5 μM, a wide linear range of 5 μM–0.65 mM, a short response time (within 5 s), and high sensitivity (30.64 μA mM^?1 cm^?2) and stability (80% remains after 30 days).     

An Amperometric Glucose Electrode Based on Adsorbed Glucose Oxidase on Palladium/Gold Modified Graphite

Abstract

A glucose electrode was constructed by adsorbing glucose oxidase (GOD) on a modified electrode for H₂ O ₂ oxidation, consisting of Pd/Au sputtered on graphite. Maximally, 0.8 U cm^?2 of GOD could be adsorbed. The electrode was used in a f.i.a. manifold for determination of glucose. Linear calibration curves were obtained in the concentration range 3. 10^?6 4. 10^?3 mol L^?1 glucose. The applied potentials for glucose determination were + 300 mV vs. Ag/AgCl at pH 8.0, + 350 mV at pH 7.0, + 400 mV at pH 6.0 and + 500 mV at pH 5.0. The activity vs. pH profile of adsorbed GOD was broad having an optimum between pH 5 and 6. The apparent kinetic parameters for adsorbed GOD, K_M ^app and i_max, were found to be 50 mM and 160 uA at optimal pH.