Electrochemical study of breast cancer cells MCF-7 and its application in evaluating the effect of diosgenin.

The electrochemical behavior of breast cancer cells was studied on a graphite electrode by cyclic voltammetry (CV) and potentiometric stripping analysis (PSA). In both cases, only one oxidative peak at approximately +0.75 V was observed. The peak area in PSA was used to study the growth of the cells and the effect of diosgenin on MCF-7 cells. The results showed that diosgenin can effectively inhibit the viability and proliferation of the breast cancer cells.     

Simultaneous and Sensitive Detection of Cd(II) and Pb(II) Using a Novel Bismuth Film/Ordered Mesoporous Carbon‐molecular Wire Modified Graphite Carbon Paste Electrode

An electrochemical sensor for the simultaneous and sensitive detection of Cd(II) and Pb(II) is proposed on the basis of square‐wave anodic stripping voltammetry (SWASV) experiments using a novel bismuth film/ordered mesoporous carbon‐molecular wire modified graphite carbon paste electrode (Bi/OMC‐MW/GCPE). Ordered mesoporous carbon (OMC) and molecular wire (MW) (diphenylacetylene) were used as the modifier and binder, respectively. The Bi/OMC‐MW/GCPE was prepared with the addition of graphite powder, OMC and DPA at the ratio of 2 : 1 : 1. The electrochemical properties and morphology of the electrode were characterized by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), SWASV and scanning electron microscopy (SEM). The parameters affecting the stripping current response were investigated and optimized. The experimental results show that the prepared electrode exhibited excellent electrochemical performance, good electrical conductivity and a high stripping voltammetric response. Under optimized conditions, a linear range was achieved over a concentration range from 1.0 to 70.0 μg/L for both Cd(II) and Pb(II) metal ions, with detection limits of 0.07 μg/L for Cd(II) and 0.08 μg/L for Pb(II) (S/N=3) with the deposition time 150 s. Moreover, the sensor exhibited improved sensitivity and reproducibility compared to traditional CPEs. The fabricated electrode was then successfully used to satisfactorily detect Cd(II) and Pb(II) in real soil samples.     

Cyclic Voltammograms of Ferrocene on Multi‐Walled Carbon Nanotubes (MWCNTs)‐Modified Edge Plane Pyrolytic Graphite (EPPG) Electrode in Room Temperature Ionic Liquids (RTILs) of 1‐Ethyl‐3‐Methylimidazolium Tetrafluoroborate (EMIBF4)

In this work, the electrochemical behavior of ferrocene (Fc) was investigated by cyclic voltammetry (CV) in room temperature ionic liquids (RTILs) of 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIBF₄) on glass carbon (GC), edge plane pyrolytic graphite (EPPG) and multi‐walled carbon nanotube (MWCNTs)‐modified EPPG electrodes, respectively. The results demonstrated that on GC electrode, pairs of well‐defined reversible peaks were observed, while for the electrode of EPPG, the peak potential separation (ΔE_p) is obviously larger than the theoretical value of 59 mV, hinting that the electrode of EPPG is distinguished from the commonly used electrode, consistent with the previous proposition that EPPG has many “defects”. To obtain an improved electrochemical response, multi‐walled carbon nanotubes (MWCNTs) were modified on the electrode of EPPG; the increased peak current and promoted peak potential separation not only proved the existence of “defects” in MWCNTs, but also supported that “creating active points” on an electrode is the main contribution of MWCNTs. Initiating the electrochemical research of Fc on the MWCNTs‐modified EPPG electrode in RTILs and verifying the presence of “defects” on both EPPG and MWCNTs using cyclic voltammograms (CVs) of Fc obtained in RTILs of EMIBF₄, is the main contribution of this preliminary work.     

Underpotential Deposition and Stripping of Lead at Disorganized Monolayer‐Modified Gold Electrodes

Underpotential deposition (UPD) and stripping of Pb²⁺ at thiol‐based disorganized monolayer‐modified gold electrodes was studied by cyclic voltammetry (CV) and electrochemical quartz crystal microgravimetry (EQCM). Electrodes modified with mercaptoacetic acid or mercaptoethane sulfonic acid were studied. Due to the proximity of the potentials for the Pb UPD and thiol reductive desorption, achievement of a UPD‐stripping voltammetry methodology for determination of low concentrations of Pb²⁺ was not successful. However by comparison of the CV and EQCM data and consideration of the possible mass changes per mole electrons transferred in light of the other species present in solution, possible mechanisms are put forward for the deposition and stripping of Pb²⁺ at thiol‐modified electrodes.     

Electrochemical Detection of a Cancer Biomarker mir‐21 in Cell Lysates Using Graphene Modified Sensors

In the present study, the voltammetric and impidimetric detection of microRNA‐21, mir‐21 from cell lysates was investigated for the first time by using graphene modified disposable pencil graphite electrodes (GME). The surface characterization of GME was performed via electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM). Upon passive adsorption of inosine substituted antimicroRNA‐21, antimir‐21 probe, InP, onto the surface of GME and then solid phase hybridization of InP with mir‐21, the target, the electrochemical detection was performed by using Differential Pulse Voltammetry (DPV) and EIS techniques. This developed biosensor, GME has presented a 2.77 times lower detection limit of 2.09 µg/mL (3.12 pmol) with respect to unmodified pencil graphite electrode (GE). Moreover it is capable of analyzing mir‐21 in the cell lysates of mir‐21 positive breast cancer cell line (MCF‐7) contrast to mir‐21 negative hepatoma cell line (HUH‐7). The proposed electrochemical yes‐no system does not require any purification and/or amplification step prior to fast detection of mir‐21 from real samples.     

The Electrochemical Behavior of a N‐containing Calix[4]arene Derivative

The electrochemical behavior of 5,11,17,23‐Tetrakis‐dimethylaminomethylcalix[4]arene (DCA) has been investigated by cyclic voltammetry (CV). The results show that there is an irreversible electrochemical oxidative wave with peak potential of 1.35 V in chloroform at a glassy carbon electrode. The kinetic parameters of the andic wave, such as α, n and k_s, were discussed. In addition, a new pair of quasi‐reversible redox peaks with peak potentials of 0.72 V and 0.94 V was found. It can result in DCA electrodeposition at the electrode surface. This film modified electrode was characterized by CV and electrochemical impedance spectroscopy (EIS). Moreover, the possible mechanism of electrodeposition was also discussed     

Voltammetric Reduction of a 4‐Nitroimidazole Derivative on a Multiwalled Carbon Nanotubes Modified Glassy Carbon Electrode

We report the electrochemical behavior of a 4‐nitroimidazole derivative, 1‐methyl‐4‐nitro‐2‐hydroxymethylimidazole (4‐NImMeOH), on glassy carbon electrode (GCE) modified with multiwalled carbon nanotubes (MWCNT). As dispersing agents, dimethylformamide (DMF) and water were used. The electrochemical response of the resulting electrodes was evaluated using linear sweep, cyclic and square‐wave voltammetry (LSV, CV and SWV). Several parameters such as medium pH, nature and concentration of the CNTs dispersion and accumulation time were tested. The optimal conditions determined for obtain better response were: pH 2, dispersion concentration=4 mg/mL of CNT in water, accumulation time=7 min. The MWCNT‐modified GCE exhibited attractive electrochemical properties producing enhanced currents with a significant reduction in the overpotential and good signal‐to‐noise characteristics, in comparison with the bare GCE. The modified electrode is highly repeatable for consecutive measurements, reaching a variation coefficient of 2.9% for ten consecutive runs.     

Electrochemical Behavior of o‐Nitrophenol at Hexagonal Mesoporous Silica Modified Carbon Paste Electrodes

A hexagonal mesoporous silica (HMS) modified carbon paste electrode (CPE) was fabricated and characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) methods (ferrocene as a probe). The electrochemical behavior of nitrophenol (o‐NP) at the HMS modified electrode (HMSCPE) was investigated. Compared with CPE, a well‐defined reduction peak and a remarkably peak current response was observed. It is indicated that mesoporous HMS exhibited remarkable enhancement effects on the electrochemical reduction of o‐NP. The electrochemical reduction mechanism was also discussed. Consequently, a simple and sensitive electrochemical method was proposed for the determination of o‐NP, which was used to determine o‐NP in waste water samples.     

Preparation of Novel Arrays Silver Nanoparticles Modified Polyrutin Coat‐Paraffin‐Impregnated Graphite Electrode for Tyrosine and Tryptophan's Oxidation

A novel array silver nanoparticles and Rutin complex film modified paraffin‐impregnated graphite electrode was proposed in this work (denoted as Ag/Rutin/WGE). The characteristics were investigated by the field emission scanning electron microscopy (FE‐SEM), infrared spectra (IR), UV‐visible (UV), X‐ray photoelectron spectroscopy (XPS) and electrochemical techniques. Silver ions were gradually chelated by polyrutin film at 4′‐oxo‐5′‐OH and 5‐OH‐4‐oxo sites accompanying adsorption, then. Silver nanoparticles were highly‐dispersed electrodeposited on polyrutin film. The electrochemical behaviors of tyrosine (Tyr) and tryptophan (Trp) were studied by cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques. The Ag/Rutin/WGE electrode shows overlapping catalysis for the oxidation of Tyr and Trp. The linear response of Tyr and Trp were 0.3–10.0 and 0.7–70.0 μM with detection limit of 0.07 and 0.1 μM in a signal‐to‐noise ratio of 3.     

Electrochemical Characterization of Gold 6‐Amino‐2‐mercaptobenzothiazole Self‐Assembled Monolayer for Dopamine Detection in Pharmaceutical Samples

A new sensor, gold‐6‐amino‐2‐mercaptobenzothiazole (6A2MBT), was fabricated via a self‐assembly procedure. Electrochemical properties of the monolayer were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The modified electrode showed excellent antifouling property against the oxidation products of DA, allowed us to construct a dynamic calibration curve with two linear parts, 1.00×10^?6 to 3.72×10^?4 and 3.72×10^?4 to 6.42×10^?4 M DA, with correlation coefficients of 0.997 and 0.992 and a detection limit of 1.57×10^?7 M DA by using differential pulse voltammetry (DPV), respectively. Finally, the performance of the Au‐6A2MBT modified electrode was successfully tested for electrochemical detection of DA in a pharmaceutical sample.     

A Novel Electrochemical Sensor Based on Copper‐based Metal‐Organic Framework for the Determination of Dopamine

A glassy carbon electrode (GCE) modified with a copper‐based metal‐organic framework (MOF) [HKUST‐1, HKUST‐1 = Cu₃(BTC)₂ (BTC = 1,3,5‐benzenetricarboxylicacid)] was developed as a highly sensitive and simple electrochemical sensor for the determination of dopamine (DA). The MOF was prepared by a hydrothermal process, and the morphology and crystal phase of the MOF were characterized by scanning electron microscopy (SEM) and X‐ray diffraction (XRD), respectively. Meanwhile, the electrochemical performance was investigated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and electrochemical impedance spectroscopy (EIS). Under optimized conditions, the modified electrode showed excellent electrocatalytic activity and high selectivity toward DA. The linear response range was from 5.0 × 10⁻⁷ to 1.0 × 10⁻⁴ M and the detection limit was as low as 1.5 × 10⁻⁷ M. Moreover, the electrochemical sensor was used to detect DA in real samples with excellent results. MOF‐based sensors hold great promise for routine sensing applications in the field of electrochemical sensing.     

Carbon Paste Electrode Incorporating 1‐[4‐(Ferrocenyl Ethynyl) Phenyl]‐1‐Ethanone for Electrocatalytic and Voltammetric Determination of Tryptophan

A carbon paste electrode spiked with 1‐[4‐ferrocenyl ethynyl) phenyl]‐1‐ethanone (4FEPE) was constructed by incorporation of 4FEPE in graphite powder‐paraffin oil matrix. It has been shown by direct current cyclic voltammetry and double step chronoamperometry that this electrode can catalyze the oxidation of tryptophan (Trp) in aqueous buffered solution. It has been found that under optimum condition (pH 7.00), the oxidation of Trp at the surface of such an electrode occurs at a potential about 200 mV less positive than at an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α and rate constant for the chemical reaction between Trp and redox sites in 4FEPE modified carbon paste electrode (4FEPEMCPE) were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of Trp showed a linear dependent on the Trp concentrations and linear calibration curves were obtained in the ranges of 6.00×10^?6 M–3.35×10^?3 M and 8.50×10^?7 M–6.34×10^?5 M of Trp concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 1.80×10^?6 M and 5.60×10^?7 M by CV and DPV methods. This method was also examined as a selective, simple and precise new method for voltammetric determination of tryptophan in real sample.     

Direct Electrochemistry of Cytochrome c on a Silica Sol‐Gel Film Modified Electrode

Dilute silica sol‐gel was simply dropped on the surface of a basal plane graphite electrode (BPGE) to form a silica sol‐gel film modified electrode. Direct electrochemical response of cytochrome c (Cyt c) on the modified electrode was observed by cyclic voltammetry (CV). The results suggested that Cyt c could be tightly adsorbed on the surface of the silica sol‐gel film modified electrode. A couple of well‐defined and nearly reversible redox peaks can be observed in a phosphate buffer solution (pH 7.0), which anodic and cathodic peak potentials were at ?0.243 and ?0.306 V (vs. Ag/AgCl), respectively. Cyt c adsorbed on the surface of silica sol‐gel film shows a remarkable electrocatalytic activity for the reduction of oxygen. Based on these, a third‐generation biosensor could be constructed to detect the concentration of oxygen in aqueous solution.     

Molecularly Imprinted Polypyrrole for DNA Determination

In this study graphite electrodes modified by a thin DNA‐imprinted polypyrrole layer, which was able to bind specific target‐DNA, are reported. For this aim, electrochemical synthesis of polypyrrole was performed on a pencil graphite electrode by cyclic voltammetry (CV) or by potential pulse sequences (PPS). The modified electrode surface was used for electrochemical determination of target‐DNA by differential pulse voltammetry. According to our best knowledge this is a first report on the application of DNA‐imprinted polymer for the determination of target‐DNA. The results showed that the molecularly imprinted polypyrrole (MIPPy) layer that formed on the carbon electrode surface was sensitive for target‐DNA, while the nonimprinted polypyrrole layer was not sensitive to the same target‐DNA. Comparison of electrodes modified using PPS and CV techniques is presented.     

Adsorptive Stripping Voltammetric Determination of 4‐Hexylresorcinol in Pharmaceutical Products Using Multiwalled Carbon Nanotube Based Electrodes

A sensitive electroanalytical method is presented for the determination of 4‐hexylresorcinol using adsorptive stripping voltammetry (AdsSV) at a multiwalled carbon nanotube modified basal plane pyrolytic graphite electrode (MWCNT‐BPPGE). This method is also extended to the use of a MWCNT modified screen‐printed electrode (MWCNT‐SPE), thereby demonstrating that this approach can easily be incorporated into a facile and inexpensive electrochemical sensor.     

Fabrication of Chitosan‐Multiwall Carbon Nanotube Nanocomposite Containing Ferri/Ferrocyanide: Application for Simultaneous Detection of D‐Penicillamine and Tryptophan

We report a simple and effective strategy for fabrication of the nanocomposite containing chitosan (CS) and multiwall carbon nanotube (MWNT) coated on a glassy carbon electrode (GCE). The characterization of the modified electrode (CS‐MWNT/GC) was carried out using scanning electron microscopy (SEM) and UV–vis absorption spectroscopy. The electrochemical behavior of CS‐MWNT/GC electrode was investigated and compared with the electrochemical behavior of chitosan modified GC (CS/GC), multiwalled carbon nanotube modified GC (MWNT/GC) and unmodified GC using cyclic voltammetry (CV) and electron impedance spectroscopy (EIS). The chitosan films are electrochemically inactive; similar background charging currents are observed at bare GC. The chitosan films are permeable to anionic Fe(CN)₆^3?/4? (FC) redox couple. Electrochemical parameters, including apparent diffusion coefficient for the Fe(CN)₆^3?/4? redox probe at FC/CS‐MWNT/GC electrode is comparable to values reported for cast chitosan films. This modified electrode also showed electrocatalytic effect for the simultaneous determination of D‐penicillamine (D‐PA) and tryptophan (Trp). The detection limit of 0.9 μM and 4.0 μM for D‐PA and Trp, respectively, makes this nanocomposite very suitable for determination of them with good sensitivity.     

Graphene Functionalized Graphite Electrode with Diphenylacetylene for Sensitive Electrochemical Determination of Adenosine‐5′‐triphosphate

In this paper a molecular wire modified carbon paste electrode (MW‐CPE) was firstly prepared by mixing graphite powder with diphenylacetylene (DPA). Then a graphene (GR) and chitosan (CTS) composite film was further modified on the surface of MW‐CPE to receive the graphene functionalized electrode (CTS‐GR/MW‐CPE), which was used for the sensitive electrochemical detection of adenosine‐5′‐triphosphate (ATP). The CTS‐GR/MW‐CPE exhibited excellent electrochemical performance and the electrochemical behavior of ATP on the CTS‐GR/MW‐CPE was carefully studied by cyclic voltammetry with an irreversible oxidation peak appearing at 1.369 V (vs. SCE). The electrochemical parameters such as charge transfer coefficient (α) and electrode reaction standard rate constant (k_s) were calculated with the results of 0.53 and 5.28×10^?6 s^?1, respectively. By using differential pulse voltammetry (DPV) as detection technique, the oxidation peak current showed good linear relationship with ATP concentration in the range from 1.0 nM to 700.0 µM with a detection limit of 0.342 nM (3σ). The common coexisting substances, such as uric acid, ascorbic acid and guanosine‐5′‐triphosphate (GTP), showed no interferences and the modified electrode was successfully applied to injection sample detection.     

Preparation and Characterization of a Tin Pentacyanonitrosylferrate‐Modified Carbon Ceramic Electrode: Application to Electrocatalytic Oxidation and Amperometric Detection of L‐Cysteine

The sol‐gel technique was used to construct tin pentacyanonitrosylferrate (SnPCNF) modified composite carbon ceramic electrode (CCE). This involves two steps: construction of CCE containing metallic Sn powder and then electrochemical creating of SnPCNF on the surface of CCE. The SnPCNF modified CCE (SnPCNFlCCE) was characterized by energy‐dispersive X‐ray (EDX), FTIR and cyclic voltammetry (CV) techniques. The SnPCNF film showed electrocatalytic activity toward the oxidation of L ‐cysteine. A linear calibration plot was obtained over the L ‐cysteine concentration range 1–51 μM using chronoamperometry. L ‐cysteine was determined amperometrically at the surface of this modified electrode. The detection limit (for a signal to noise of 3) and sensitivity were found to be 0.62 μM and 126 μA/mM, respectively.     

Polystyrene sulphonate wrapped multiwalled carbon nanotubes modified graphite electrode for simultaneous determination of ascorbic acid, dopamine and uric acid

Graphite electrode is modified by casting multi-walled carbon nanotubes (MWCNTs) wrapped with polystyrene sulphonate (PSS) onto the surface of the bare graphite electrode. The modified electrode was characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The behavior of the modified electrode towards the oxidation of ascorbic acid (AA), dopamine (DA) and uric acid (UA) has been determined by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and chronoamperometry (CA). The modified electrode showed better electrocatalytic activity towards AA, DA and UA compared to bare graphite electrode. The electrochemical oxidation signals of AA, DA and UA are well separated into three distinct peaks with peak potential difference of 222, 128 and 350 mV between AA-DA, DA-UA and AA-UA respectively in CV studies and corresponding peak potential separation in DPV are 228, 120 and 348 mV. This modified electrode was successfully used for simultaneous determination of AA, DA and UA in ternary mixture.     

Determination of Esomeprazole on an Electropolymerized L‐arginine and β‐cyclodextrin Modified Screen Printed Carbon Electrode

The formation of an inclusion complex of the proton‐pump inhibitor (PPI) drug esomeprazole (ESO) with ß‐cyclodextrin (ß‐CD) has been investigated and proven by cyclic voltammetry (CV). The formation constant of the complex was determined. Thereafter, an electropolymerized β‐CD and L‐arginine (L‐arg) modified screen printed carbon electrode (P‐β‐CD‐L‐arg/SPCE) was developed for the determination of ESO using differential pulse adsorptive stripping voltammetry (DPAdSV). A significant enhancement of the peak current was observed when applying an accumulation step due to the effect of adsorption. Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) further indicated that the polymer of β‐CD and L‐arg efficiently improved the electron transfer kinetic between analyte and electrode surface. Under the optimized conditions, the oxidation peak current was linearly proportional to the concentration of the drug in the range of 1.0×10^?8 to 1.0×10^?5 M. The DPAdSV method was successfully used to determine the concentrations of the drug in spiked human serum samples.