Electroanalytical Determination of N‐Nitrosamines in Aqueous Solution Using a Boron‐Doped Diamond Electrode

The electrochemical methods cyclic and square‐wave voltammetry were applied to develop an electroanalytical procedure for the determination of N‐nitrosamines (N‐nitrosopyrrolidine, N‐nitrosopiperidine and N‐nitrosodiethylamine) in aqueous solutions. Cyclic voltammetry was used to evaluate the electrochemical behaviors of N‐nitrosamines on boron‐doped diamond electrodes. It was observed an irreversible electrooxidation peak located in approximately 1.8 V (vs. Ag/AgCl) for both N‐nitrosamines. The optimal electrochemical response was obtained using the following square‐wave voltammetry parameters: f=250 Hz, E_sw=50 mV and E_s=2 mV using a Britton–Robinson buffer solution as electrolyte (pH 2). The detection and quantification limits determined for total N‐nitrosamines were 6.0×10^?8 and 2.0×10^?7 mol L^?1, respectively.     

Electrochemical Behavior and Electroanalytical Determination of Indole‐3‐Acetic Acid Phytohormone on a Boron‐Doped Diamond Electrode

In this work, a boron‐doped diamond (BDD) electrode was used for the electroanalytical determination of indole‐3‐acetic acid (IAA) phytohormone by square‐wave voltammetry. IAA yielded a well‐defined voltammetric response at +0.93 V (vs. Ag/AgCl) in Britton–Robinson buffer, pH 2.0. The process could be used to determine IAA in the concentration range of 5.0 to 50.0 µM (n=8, r=0.997), with a detection limit of 1.22 µM. The relative standard deviation of ten measurements was 2.09 % for 20.0 µM IAA. As an example, the practical applicability of BDD electrode was tested with the measurement of IAA in some plant seeds.     

Selective Electroanalytical Assay for Cysteine at a Boron Doped Diamond Electrode

The electrochemical oxidation of the cysteine‐quinone adduct has been examined as a means of providing an electroanalytical cysteine specific detection protocol. The appliance of square‐wave voltammetry allowed 0.5 μM as a limit of detection. The effects of various biologically relevant interferences including other thiols were studied and found to present no change in the voltammetric profile. The practical applicability and efficiency of the methodology was probed through the determination of cysteine concentration in growth tissue medium.     

Electroanalytical Determination of Lidocaine in Pharmaceutical Preparations Using Boron‐Doped Diamond Electrodes

A new electroanalytical procedure was developed for the determination of lidocaine in commercial local anesthetics products containing lidocaine as the active ingredient. The procedure is based on the use of electrochemical methods as cyclic and square‐wave voltammetry, with boron‐doped diamond electrodes. The oxidation of lidocaine in Britton–Robinson buffer (0.1 mol L^?1) using this type of electrode gives rise to one irreversible peak in 1.68 V (versus Ag/AgCl). The detection and quantification limits obtained from pure water were 10.0 and 34.4 μg/L, respectively. The proposed electrochemical method was also successfully applied to the analysis of commercially available pharmaceutical preparations. The electrochemical responses of pharmaceutical preparations (gels) were identical to those of standard lidocaine. No influence of propyleneglycol present in the gels on the voltammetric responses was observed. Lidocaine recoveries ranged from 97.6% to 99.2%.     

Non‐Invasive Salivary Electrochemical Quantification of Paraquat Poisoning Using Boron Doped Diamond Electrode

The present work describes the first electrochemical method for quantifying paraquat herbicide poisoning in human saliva samples. Paraquat shows two couples of well‐defined peaks in aqueous solution using a boron doped diamond (BDD) electrode. By using square wave voltammetry (SWV) technique under optimum experimental conditions, a linear analytical curve was obtained for paraquat concentrations ranging from 0.800 to 167 µmol L^?1, with a detection limit of 70 nmol L^?1. This method was applied to quantify paraquat spikes in human saliva samples and in two different water samples (tap and river). The recovery values obtained ranged from 83.0 to 104 % and 99.1 to 105 %, respectively, which highlight the accuracy of the proposed method.     

Sensitive Detection of Capsaicin by Adsorptive Stripping Voltammetry at a Boron‐Doped Diamond Electrode in the Presence of Sodium Dodecylsulfate

In the present paper, a sensitive electroanalytical methodology for the determination of capsaicin using adsorptive stripping voltammetry (AdSV) at a boron‐doped diamond (BDD) electrode is presented. The voltammetric results indicate that in the presence of sodium dodecylsulfate (SDS) the BDD electrode remarkably enhances the oxidation of capsaicin which leads to an improvement of the peak current with a shift of the peak potential to less negative values. A linear working range of 0.05 to 6.0 µg mL^?1 (0.16–20 µM) with a detection limit of 0.012 µg mL^?1 (0.034 µM) has been obtained using BDD electrode by AdSV.     

Electroanalytical Determination of Promethazine Hydrochloride in Pharmaceutical Formulations on Highly Boron‐Doped Diamond Electrodes Using Square‐Wave Adsorptive Voltammetry

The electrochemical oxidation of promethazine hydrochloride was made on highly boron‐doped diamond electrodes. Cyclic voltammetry experiments showed that the oxidation mechanisms involved the formation of an adsorbed product that is more readily oxidized, producing a new peak with lower potential values whose intensity can be increased by applying the accumulation potential for given times. The parameters were optimized and the highest current intensities were obtained by applying +0.78 V for 30 seconds. The square‐wave adsorptive voltammetry results obtained in BR buffer showed two well‐defined peaks, dependent on the pH and on the voltammetric parameters. The best responses were obtained at pH 4.0, frequency of 50 s^?1, step of 2 mV, and amplitude of 50 mV. Under these conditions, linear responses were obtained for concentrations from 5.96×10^?7 to 4.76×10^?6 mol L^?1, and calculated detection limits of 2.66×10^?8 mol L^?1 (8.51 μg L^?1) for peak 1 and of 4.61×10^?8 mol L^?1 (14.77 μg L^?1) for peak 2. The precision and accuracy were evaluated by repeatability and reproducibility experiments, which yielded values of less than 5.00% for both voltammetric peaks. The applicability of this procedure was tested on commercial formulations of promethazine hydrochloride by observing the stability, specificity, recovery and precision of the procedure in complex samples. All results obtained were compared to recommended procedure by British Pharmacopeia. The voltammetric results indicate that the proposed procedure is stable and sensitive, with good reproducibility even when the accumulation steps involve short times. It is therefore very suitable for the development of the electroanalytical procedure, providing adequate sensitivity and a reliable method.     

Sensitive Determination of the Diquat Herbicide in Fresh Food Samples on a Highly Boron‐Doped Diamond Electrode

The highly boron‐doped diamond electrode (HBDD) combined with square wave voltammetry (SWV) was used in the development of an analytical procedure for diquat determination in potato and sugar cane samples and lemon, orange, tangerine and pineapple juices. Preliminary experiments realised in a medium of 0.05 mol L^?1 Na₂B₄O₇ showed the presence of two voltammetric peaks around ?0.6 V and around ?1.0 V vs. Ag/AgCl/Cl^? 3.0 mol L^?1, where the first peak could be successfully used for analytical proposes due the facility in the electrode surface renovation. After the experimental and voltammetric optimisation, the calculated detection and quantification limits were 1.6×10^?10 mol L^?1 and 5.3×10^?10 mol L^?1 (0.057 µg L^?1 and 0.192 µg L^?1, respectively), which are lower than the maximum residue limit established for fresh food samples by the Brazilian Sanitary Vigilance Agency. The proposed methodology was used to determine diquat residues in potato and sugar cane samples and lemon, orange, tangerine and pineapple juices and the calculated recovery efficiencies indicated that the proposed procedure presents higher robustness, stability and sensitivity, good reproducibility, and is very adequate for diquat determination in complex samples.     

A New Indirect Electroanalytical Method to Monitor the Contamination of Natural Waters with 4‐Nitrophenol Using Multiwall Carbon Nanotubes

The electrochemical detection of the hazardous pollutant 4‐nitrophenol (4‐NP) at low potentials, in order to avoid matrix interferences, is an important research challenge. This study describes the development, electrochemical characterization and utilization of a multiwall carbon nanotube (MWCNT) film electrode for the quantitative determination of 4‐NP in natural water. Electrochemical impedance spectroscopy measurements showed that the modified surface exhibits a decrease of ca. 13 times in the charge transfer resistance when compared with a bare glassy carbon (GC) surface. Voltammetric experiments showed the possibility to oxidize a hydroxylamine layer (produced by the electrochemical reduction of 4‐NP on the GC/MWNCT surface) in a potential region which is approximately 700 mV less positive than that needed to oxidize 4‐NP, thus minimizing the interference of matrix components. The limit of detection for 4‐NP obtained using square‐wave voltammetry (0.12 μmol L^?1) was lower than the value advised by EPA. A natural water sample from a dam located in São Carlos (Brazil) was spiked with 4‐NP and analyzed by the standard addition method using the GC/MWCNT electrode, without any further purification step. The recovery procedure yielded a value of 96.5% for such sample, thus confirming the suitability of the developed method to determine 4‐NP in natural water samples. The electrochemical determination was compared with that obtained by HPLC with UV‐vis detection.     

Voltammetric Determination of 3‐Nitrofluoranthene and 3‐Aminofluoranthene at Boron Doped Diamond Thin‐Film Electrode

The voltammetric behavior of 3‐nitrofluoranthene and 3‐aminofluoranthene was investigated in mixed methanol‐water solutions by differential pulse voltammetry (DPV) at boron doped diamond thin‐film electrode (BDDE). Optimum conditions have been found for determination of 3‐nitrofluoranthene in the concentration range of 2×10^?8–1×10^?6 mol L^?1, and for determination 3‐aminofluorathnene in the concentration range of 2×10^?7–1×10^?5 mol L^?1, respectively. Limits of determination were 3×10^?8 mol L^?1 (3‐nitrofluoranthene) and 2×10^?7 mol L^?1 (3‐aminofluoranthene).     

Electrochemical Determination of Vitamin D3 in Pharmaceutical Products by Using Boron Doped Diamond Electrode

A sensitive square‐wave voltammetry method was developed to determine cholecalciferol (vitamin D₃) in pharmaceutical products at boron‐doped diamond electrode as a working electrode. Vitamin D₃ provided a well‐defined voltammetric peak at around +1.00 V (vs. Ag/AgCl, 3.5 mol dm^?3) in 0.02 mol dm^?3 Britton‐Robinson buffer pH 5.0 prepared in 50 % ethanol. The influence of various factors such as type and pH of the supporting electrolyte, scan rate and square‐wave parameters were studied and optimized. Under optimum conditions, the oxidation peak current increased linearly with the concentration of vitamin D₃ over the range of 2 to 200 μmol dm^?3. The calculated limit of detection and limit of quantitation were 0.17 μmol dm^?3 and 0.51 μmol dm^?3, respectively. The boron‐doped diamond electrode exhibited specific recognition capability for cholecalciferol amongst possible interferences, and the determination of vitamin D₃ was possible in samples such as commercial pharmaceutical products without complicated sample pretreatments.     

Determination of Total Phenols in Foods by Boron Doped Diamond Electrode

A robust electrochemical method to measure the total phenol content in food samples is presented. Under optimal condition, BDD electrode showed excellent performance to detect the oxidation of several phenols and does not present the drawback due to electrode fouling. The analytical method used to perform such measurement has been optimized and successfully applied in different food samples. The results obtained were compared with the standard Folin–Ciocalteau method.     

Determination of Sodium Diethyldithiocarbamate in Water by Anodic Voltammetry Using a Boron‐Doped Diamond Electrode

An electrochemical study was made of the anodic behavior of sodium diethyldithiocarbamate (DEDTC) using a boron‐doped diamond electrode (BDDE) in sodium sulfate supporting electrolyte. This paper presents a new alternative for the electroanalytical determination of DEDTC in protic media, using cyclic voltammetry or chronoamperometry. Linear plots of current vs. concentration correlated with anodic stepwise oxidation were obtained in delimited potential ranges with very good correlation coefficients.     

硼掺杂金刚石电极及其电分析应用

一种新电极材料的发明往往会推动电分析测试的发展。硼掺杂金刚石(BDD)电极在电分析中具备宽电势窗口、低背景电流、 耐腐蚀稳定性高和低吸附的特点,因而在电分析化学中引起了广泛的兴趣。本文对BDD电极的制备、表征和基本电分析性质进行了介绍,并对其在毛细管电泳、生物传感电极、痕量金属离子检测、化学修饰电极及化学需氧量快速测定方面的应用进行了综述。     

Comparison of Boron‐Doped Diamond and Glassy Carbon Electrodes for Determination of Procaine Hydrochloride

The electrochemical oxidation of procaine hydrochloride (PC?HCL, 2‐diethylaminoethyl 4‐aminobenzoate hydrochloride) was investigated at as‐deposited boron‐doped diamond (ad‐BDD) electrode, anodically oxidized BDD (ao‐BDD) electrode and glassy carbon (GC) electrode using cyclic voltammetry (CV). Well‐defined cyclic voltammograms were obtained for PC?HCL oxidation with high signal‐to‐background (S/B) ratio, low tendency for adsorption, good reproducibility and long‐term stability at ad‐BDD electrode, demonstrating its superior electrochemical behavior and significant advantages in contrast to ao‐BDD and GC electrode. At 100 μM PC?HCL, the voltammetric S/B ratio was nearly one order of magnitude higher at an ad‐BDD electrode than that at a GC electrode. In a separate set of experiments for oxidation of 100 μM PC?HCL, 96%, 92% and 84% of the initial oxidation peak current was retained at the ad‐BDD, ao‐BDD and GC electrode, respectively, by stirring the solution after the tenth cycle. The current response was linearly proportional to the square root of the scan rate within the range 10–1000 mV s^?1 in 10 μM PC?HCL solutions, indicating that the oxidation process was diffusion‐controlled with negligible adsorption at an ad‐BDD surface. The good linearity was observed for a concentration range from 5 to 200 μM with a linear equation of y=0.03517x+0.65346 (r=0.999), and the detection limit was 0.5 μM for oxidation of PC?HCL at the ad‐BDD electrode. The ad‐BDD electrode could maintain 100% of its original activity after intermittent use for 3 months.     

Electrochemical Determination of Boron in Natural Waters

Abstract

A sensitive voltammetric method for the determination of trace boron, based on the formation of the complex of boric acid with 4‐hydroxy‐5‐[salicylideneamino]‐2‐7‐naphthalenedisulfonic acid (azomethine H) is described. The reduction of the boric acid‐azomethine H complex at a hanging mercury drop electrode was exploited by square wave voltammetry (SWV) and cyclic voltammetry to determine boron in natural water samples, which were collected in the regions surrounding the boron mines of Central Anatolia. A reduction peak that belongs to the boric acid‐azomethine H complex at this electrode was observed at ?1.05 V vs. Ag/AgCl/KCl_(sat.). The effects of various parameters, such as ligand concentration, boric acid concentration, and formation time of the boric acid‐azomethine H complex, were investigated. Electrochemical experiments were conducted in 1.0 M HOAc/0.5 M NH₄OAc buffer at pH of 4.4±0.2. Linear working range was established by regression analysis between 5.0×10^?8 M and 1.0×10^?4 M. The probable metal cation interferences in water samples were eliminated by adding EDTA (ethylenediaminetetraacetic acid) to the samples. Data obtained using the square wave voltammetric (SWV) technique was compared statistically with inductively coupled plasma mass spectroscopy (ICP‐MS) data. Evaluation of the method based on statistical data was performed and the values of the limit of detection (LOD) and limit of quantitation (LOQ) were found to be 4.17×10^?6 M and 1.39×10^?5 M, respectively.     

A Nitrite Electrochemical Sensor Based on Boron‐Doped Diamond Planar Electrochemical Microcells Modified with a Monolacunary Silicotungstate Polyoxoanion

A new boron doped diamond microcells (BDD) was modified, for rapid, selective and highly sensitive determination of nitrite, using a coating film of polyoxometalates (POMs), formed by cyclic voltammetry on the molecular p‐phenylenediamine (PPD) functionalized BDD. The scanning electron microscopy (SEM) technique was used to examine the morphology of (PPD/SiW₁₁) modified (BDD) electrode. It was found that (SiW₁₁) layer was uniformly formed on the electrode surface. It was observed that (BDD/PPD/SiW₁₁) showed excellent electrocatalytic activities towards nitrite ion. Under the selected conditions, the anodic peak maximum at ?0.6 V was linear versus nitrite concentration in the 40 µM–4 mM range, and the detection limit obtained was 20 µM. The newly developed electrode has been successfully applied to the determination of nitrite content in real river water samples.     

Heavily Boron Doped Diamond Electrodes for Ultra Sensitive Determination of Ciprofloxacin in Human Urine

Ciprofloxacin is one of the most potent fluoroquinolone antibiotics in medical treatment with a widely effective antibacterial activity. Aim of the presented paper was to use boron doped diamond electrodes for a sensitive, simple and reliable voltammetric determination of ciprofloxacin in human urine samples. Prior to the electrochemical analyses, an optimal boron doping level was determined in order to achieve the highest sensitivity. A set of boron doped diamond electrodes with the doping level in the range from 0 to 20 000 ppm B/C was used for this purpose. Electrochemical behavior of ciprofloxacin was investigated using cyclic voltammetry in an ammonium acetate buffer (pH 5), where ciprofloxacin provided a well‐defined irreversible oxidation peak at a potential of + 1.15 V. Under optimal experimental conditions, the calibration curve obtained by square‐wave voltammetry was linear in a concentration range from 0.15 to 2.11 μmol/L (R²=0.9974). A very low limit of detection (0.05 μmol/L) was obtained for the BDD electrode with the highest doping level. The developed square wave method was successfully applied to the determination of ciprofloxacin in human urine samples with a very good recovery (from 97 to 102%).     

Anodic Oxidation Behaviors of Formaldehyde at Boron‐Doped Diamond Electrodes

The electrochemical behaviors of formaldehyde (FA) at boron‐doped diamond (BDD) electrodes are investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and linear scanning voltammetry (LSV) techniques. The CV results show that the oxidation reaction of FA is influenced by the hydroxyl concentration in the solution, and the peak current response with the FA concentration is linear at the range from 10 to 100 mM. The differential capacitance from EIS results indicate that the FA molecules adsorb at the BDD electrode surface at low potential (from 1.0 to 1.4 V). The kinetic studies have been examined with the various concentrations of FA, pH, and temperature. The activation energy of FA oxidation is also calculated. The results of kinetic study indicate that the adsorption of FA molecules at the BDD electrode is the rate‐determining step at low potential (from 1.0 to 1.40 V).     

Simultaneous Determination of Acetaminophen and Ascorbic Acid at an Unmodified Boron‐Doped Diamond Electrode by Differential Pulse Voltammetry in Buffered Media

A boron‐doped diamond electrode (BDDE) was used for the simultaneous anodic determination of L ‐ascorbic acid (AA) and acetaminophen (AC) in aqueous buffered media by differential pulse voltammetry (DPV). Linear calibration plots of anodic current peaks versus concentration were obtained for both analytes in the concentration range 0.01–0.1 mM with very high correlation coefficients. RSD of 2–3% and high sensitivities were obtained from DPV data in single and dicomponent systems. The potential applicability of the DPV technique associated with standard addition was illustrated by simultaneous determination of AA and AC in real sample solutions made up from pharmaceutical products.