Electrochemistry and electrocatalytic activity of catechin film on a glassy carbon electrode toward the oxidation of hydrazine

A very stable electroactive film of catechin was electrochemically deposited on the surface of activated glassy carbon electrode. The electrochemical behavior of catechin modified glassy carbon electrode (CMGCE) was extensively studied using cyclic voltammetry. The properties of the electrodeposited films, during preparation under different conditions, and the stability of the deposited film were examined. The charge transfer coefficient (α) and charge transfer rate constant (k _s) for catechin deposited film were calculated. It was found that the modified electrode exhibited excellent electrocatalytic activity toward hydrazine oxidation and it also showed a very large decrease in the overpotential for the oxidation of hydrazine. The CMGCE was employed to study electrocatalytic oxidation of hydrazine using cyclic voltammetry, rotating disk voltammetry, chronoamperometry, amperometry and square-wave voltammetry as diagnostic techniques. The catalytic rate constant of the modified electrode for the oxidation of hydrazine was determined by cyclic voltammetry, chronoamperometry and rotating disk voltammetry and was found to be around 10⁻³ cm s⁻¹ . In the used different voltammetric methods, the plot of the electrocatalytic current versus hydrazine concentration is constituted of two linear segments with different ranges of hydrazine concentration. Furthermore, amperometry in stirred solution exhibits a detection limit of 0.165 μM and the precision of 4.7% for replicate measurements of 40.0 μM solution of hydrazine.     

Design of a Sensitive Electrochemical Sensor Based on Ferrocene-reduced Graphene Oxide/Mn-spinel for Hydrazine Detection

Herein, we report construction of a ferrocene-reduced graphene oxide-Mn spinel modified glassy carbon electrode (Fc−G/Mn₃O₄/GCE) as a sensitive electrochemical probe for hydrazine detection via its oxidation. The synergistic effect of ferrocene, graphene oxide and Mn₃O₄ provides it a great electrocatalytic effect. The electrochemical investigations of Fc−G/Mn₃O₄/GCE were studied using cyclic voltammetry, while differential pulse voltammetry was utilized for recording the electrocatalytic sensing of hydrazine. The prepared Fc−G/Mn₃O₄ offers a platform for sensitive and selective detection of low-level hydrazine in two linear ranges from 0.045 to 108 μM and 108 to 653 μM with limit of detection 8.5 nM. Real sample analysis was also performed in local industrial water samples with satisfactory recovery results.     

Preparation,Characterization, and Electrocatalytic Properties of Cobalt Oxide and Cobalt Hexacyanoferrate Hybrid Films

Polynuclear mixed‐valent films of cobalt oxide and cobalt hexacyanoferrate (CoOCoHCF) have been deposited on electrode surfaces from a solution of Co²⁺ and Fe(CN)₆^3? ions by repetitive potential cycling method. Simultaneous cyclic voltammetry and electrochemical quartz crystal microbalance measurements demonstrate the steady growth of modified film. The effect of type of monovalent cations as well as acidity of the supporting electrolyte on film growth and redox behavior of resulting film was investigated. In pure supporting electrolyte, electrochemical responses of modified electrode resemble with that of a surface immobilized redox couple. The hybrid film electrodes showed electrocatalytic activity toward oxidation of NADH, hydrazine and hydroxylamine. The feasibility of using our modified electrodes for analytical application was also explored.     

Acetylferrocene Modified Carbon Paste Electrode; A Sensor for Electrocatalytic Determination of Hydrazine

The electrocatalytic oxidation of hydrazine at a carbon paste electrode spiked with acetylferrocene as a mediator was studied by cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. In contrast to other ferrocenic compounds, acetylferrocene exhibits a chemical irreversible behavior, but it can act as an effective mediator for electrocatalytic oxidation of hydrazine, too. The heterogeneous electron transfer rate constant between acetylferrocene and the electrode substrate (carbon paste) and the diffusion coefficient of spiked acetylferrocene in silicon oil were estimated to be about 3.45×10^?4 cm s^?1 and 4.45×10^?9 cm² s^?1, respectively. It has been found that under the optimum conditions (pH 7.5) the oxidation of hydrazine occurs at a potential of about 228 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak current of hydrazine was linearly dependent on its concentration and the obtained linear range was 3.09×10^?5 M–1.03×10^?3 M. The detection limit (2σ) has been determined as 2.7×10^?5 M by cyclic voltammetry. Also, the peak current was increased linearly with the concentration of hydrazine in the range of 1×10^?5 M–1×10^?3 M by differential pulse voltammetry with a detection limit of 1×10^?5 M. This catalytic oxidation of hydrazine has been applied as a selective, simple, and precise new method for the determination of hydrazine in water samples.     

Electrodeposited nano-scale islands of ruthenium oxide as a bifunctional electrocatalyst for simultaneous catalytic oxidation of hydrazine and hydroxylamine

For the first time, an electrodeposited nano-scale islands of ruthenium oxide (ruthenium oxide nanoparticles), as an excellent bifunctional electrocatalyst, was successfully used for hydrazine and hydroxylamine electrocatalytic oxidation. The results show that, at the present bifunctional modified electrode, two different redox couples of ruthenium oxides serve as electrocatalysts for simultaneous electrocatalytic oxidation of hydrazine and hydroxylamine. At the modified electrode surface, the peaks of differential pulse voltammetry (DPV) for hydrazine and hydroxylamine oxidation were clearly separated from each other when they co-exited in solution. Thus, it was possible to simultaneously determine hydrazine and hydroxylamine in the samples at a ruthenium oxide nanoparticles modified glassy carbon electrode (RuON-GCE). Linear calibration curves were obtained for 2.0-268.3 μM and 268.3-417.3 μM of hydrazine and for 4.0-33.8 μM and 33.8-78.3 μM of hydroxylamine at the modified electrode surface using an amperometric method. The amperometric method also exhibited the detection limits of 0.15 μM and 0.45 μM for hydrazine and hydroxylamine respectively. RuON-GCE was satisfactorily used for determination of spiked hydrazine in two water samples. Moreover, the studied bifunctional modified electrode exhibited high sensitivity, good repeatability, wide linear range and long-term stability.     

Electrocatalytic Oxidation and Voltammetric Determination of Hydrazine on the Tetrabromo‐p‐Benzoquinone Modified Carbon Paste Electrode

The electrochemical properties of hydrazine studied at the surface of a carbon paste electrode spiked with p‐bromanil (tetrabromo‐p‐benzoquinone) using cyclic voltammetry (CV), double potential‐step chronoamperometry and differential pulse voltammetry (DPV) in aqueous media. The results show this quinone derivative modified carbon paste electrode, can catalyze the hydrazine oxidation in an aqueous buffered solution. It has been found that under the optimum conditions (pH 10.00), the oxidation of hydrazine at the surface of this carbon paste modified electrode occurs at a potential of about 550 mV less positive than that of a bar carbon paste electrode. The electrocatalytic oxidation peak current of hydrazine showed a linear dependent on the hydrazine concentrations and linear analytical curves were obtained in the ranges of 6.00×10^?5 M–8.00×10^?3 M and 7.00×10^?6 M–8.00×10^?4 M of hydrazine concentration with CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 3.6×10^?5 M and 5.2×10^?6 M by CV and DPV methods. This method was also used for the determination of hydrazine in the real sample (waste water of the Mazandaran wood and paper factory) by standard addition method.     

Electrocatalytic Behavior of Manganese and Cobalt Porphyrins Attached to Graphene Quantum Dots: Applied in the Oxidation of Hydrazine

Manganese and cobalt metalated 5, 10, 15-tris(aminophenyl)-20-(4-carboxyphenyl) porphyrins (ClMnTA₃CPP and CoTA₃CPP) were synthesized and attached to graphene quantum dots (GQDs) via π-π interaction and electrostatic interaction. The electrochemical oxidation of hydrazine was performed via cyclic voltammetry and chronoamperometry. The CoTA₃CPP showed good electrocatalytic activity towards the oxidation of hydrazine in terms of catalytic rate constants and limits of detection (LoD). ClMnTA₃CPP showed lower overpotential 0.60 V. The introduction of GQDs improved the electrocatalytic ability when combined with CoTA₃CPP and ClMnTA₃CPP with the lowest LoD (0.0025 mM CoTA₃CPP–GQDs) followed by ClMnTA₃CPP–GQDs with 0.0033 mM.     

A potentiometric hydrazine sensor: para-Ni-tetraaminophenylporphyrin/Co-cobaltite/SNO2:F modified electrode

Three glass electrodes covered with Co-cobaltite/SnO₂:F (to obtain conducting glass electrodes) modified with p-Ni-tetraaminophenylporphyrin are described. In one electrode the porphyrin was absorbed on the electrode surface at room temperature, in another the porphyrin was electropolymerized on the electrode surface by cyclic voltammetry, and in the third the bare electrode was immersed in DMF containing the porphyrin and refluxed 6?h at 150°C. The three electrodes were tested as electrocatalysts for the oxidation of hydrazine and as potentiometric sensors of this chemical. The electrode modified by refluxing showed good electrocatalytic behavior as well as a linear relationship between its open circuit potential and the concentration of hydrazine in a concentration range from 0.16 to 12?µM, with fast response. These characteristics indicate that the conducting glass electrode of Co-cobaltite/SnO₂:F covered with p-Ni-tetraaminophenylporphyrin by the reflux method is a good potentiometric sensor of hydrazine. The active site is probably the ligand that changes its electron density by formation of a supramolecular system.     

Kinetic Study of the Electro-Catalytic Oxidation of Hydrazine on Cobalt Hydroxide Modified Glassy Carbon Electrode

Electrocatalytic oxidation of hydrazine was investigated on a cobalt hydroxide modified glassy carbon (CHM-GC) electrode in alkaline solution. The process of oxidation involved and its kinetics were established by using cyclic voltammetry, chronoamperometry techniques as well as steady state polarization measurements. In cyclic voltammetry (CV) studies, in the presence of hydrazine the peak current increase of the oxidation of cobalt hydroxide is followed by a decrease in the corresponding cathodic current. This indicates that hydrazine is oxidized on the redox mediator that is immobilized on the electrode surface via an electrocatalytic mechanism. A mechanism based on the electrochemical generation of Co(IV) active sites and their subsequent consumption by the hydrazine in question was also investigated.     

Characterization of PVC-Tetraruthenated Metalloporphyrins Modified Electrodes: Application as Electrocatalyst in the Nitrite Reduction

Summary: This paper describes the electrochemical reduction of nitrite ion in 0.1 M NaClO₄, on glassy carbon or ITO electrodes modified with mixtures PVC- tetraruthenated metalloporphyrins. This electrode is able to keep the extraordinary electrocatalytic properties of the macrocycle allowing multielectronic transfers and a great stability as a consequence of the inclusion of the macrocycles into a polymeric support such as PVC. On the other hand, the electrochemical reduction of nitrite ion on these modified electrodes studied by cyclic voltammetry shows an enhancement in the current values and lower overpotential compared with the activity of the bare glassy carbon electrode. Controlled potential electrolysis experiments verify the production of ammonia, hydrazine and hydroxylamine, showing the electrocatalytic character and the stability of this modified electrode.     

Electrocatalytic oxidation of hydrazine at poly(4,5-dihydroxy-1,3-benzenedisulfonic acid) multiwall carbon nanotubes modified-glassy carbon electrode: Improvement of the catalytic activity

A stable electroactive thin film of poly(4,5-dihydroxy-1,3-benzenedisulfonic acid) was electrochemically deposited at the surface of multiwall carbon nanotubes-glassy carbon electrode. The electrocatalytic oxidation of hydrazine has been studied at the surface of the modified electrode using cyclic voltammetry, chronoamperometry and linear sweep voltammetry as diagnostic techniques. The modified electrode exhibits good electrocatalytic activity for the oxidation of hydrazine with a good sensitivity. Linear calibration range was in the wide concentration range of 10–3540 μM hydrazine with a detection limit of 1.8 μM and a sensitivity of 85.3 nA/μM. A Tafel plot, derived from voltammograms, indicated a one-electron transfer process to be the rate-limiting step and the overall number of electrons involved in the catalytic oxidation of hydrazine was found to be four. The influences of potentially interfering substances were studied. The diffusion coefficient of hydrazine was also evaluated. Finally, the proposed modified electrode was used for the determination of hydrazine in spiked water samples.     

The Interaction of Water‐Soluble Manganese Porphyrins with DNA Films and Their Electrocatalytic Properties with Hydrazine

The electrochemistry of water‐soluble manganese porphyrins (Mn(4‐TMPyP)) has been studied as an electrochemically‐active film on double‐stranded deoxyribonucleic acid (dsDNA) modified electrodes in solutions at various pH. An electrochemical quartz crystal microbalance and cyclic voltammetry were used to study the in situ deposition of DNA on gold disk electrodes, and Mn(4‐TMPyP) (manganese meso‐tetrakis‐(N‐methyl‐4‐pyridyl)porphyrin) deposition on DNA film modified electrodes. Mn^II(4‐TMPyP) (the reduced form) is more easily deposited on a DNA film than Mn^III(4‐TMPyP) (the oxidized form). Electrodeposition of Mn(4‐TMPyP) can be performed in strong basic aqueous solutions, and shows two redox couples with electrochemically active voltammograms. The films can also be produced on glassy carbon, platinum, gold, and transparent semiconductor tin (IV) oxide electrodes. The Mn(4‐TMPyP)/DNA film was electrocatalytically oxidative for hydrazine, hydroxylamine, and SO in a basic aqueous solution through a Mn(IV) species. The electrocatalytic efficiency of Mn^IV(O)(4‐TMPyP) was observed to be greater than (OH)Mn^IV(O)(4‐TMPyP). Electrocatalytic oxidation by a Mn(4‐TMPyP) film as a catalyst for hydrazine oxidation is also discussed. This shows a new anodic peak current in the second segment after the positive scan during electrocatalytic oxidation, and is pH dependent.     

Palladium nanoparticle decorated carbon ionic liquid electrode for highly efficient electrocatalytic oxidation and determination of hydrazine

In this work arrays of palladium nanoparticles were synthesized on carbon ionic liquid electrode (CILE) (Pd/CILE), and the electrocatalytic oxidation of hydrazine was investigated using this electrode. Electrochemical oxidation of hydrazine in phosphate buffer (pH 7) was performed using cyclic voltammetry and square wave voltammetric techniques (SWV). Using the proposed electrode, a highly reproducible and well-defined peak was obtained for hydrazine at a very low potential of −0.02 V versus Ag/AgCl. A linear dynamic range of 5-800 μM with an experimental detection limit of 0.82 μM was obtained. These results show that the proposed electrode displays better electrocatalytic activity compared to the previously reported palladium modified electrodes towards oxidation of hydrazine.     

A study of the electrochemical behavior of an oxadiazole derivative electrodeposited on multi-wall carbon nanotube-modified electrode and its application as a hydrazine sensor

In this study, an oxadiazole multi-wall carbon nanotube-modified glassy carbon electrode (OMWCNT−GCE) was used as a highly sensitive electrochemical sensor for hydrazine determination. The surface charge transfer rate constant, k _s, and the charge transfer coefficient, α, for electron transfer between GCE and electrodeposited oxadiazole were calculated as 19.4 ± 0.5 s⁻¹ and 0.51, respectively at pH = 7.0. The obtained results indicate that hydrazine peak potential at OMWCNT−GCE shifted for 14, 109, and 136 mV to negative values as compared with oxadiazole-modified GCE, MWCNT−GCE, and activated GCE surface, respectively. The electron transfer coefficient, α, and the heterogeneous rate constant, k′, for the oxidation of hydrazine at OMWCNT−GCE were also determined by cyclic voltammetry measurements. Two linear dynamic ranges of 0.6 to 10.0 μM and 10.0 to 400.0 μM and detection limit of 0.17 μM for hydrazine determination were evaluated using differential pulse voltammetry. In addition, OMWCNT−GCE was shown to be successfully applied to determine hydrazine in various water samples.

     

The electrocatalytic reactions of adenine, guanine, H2O, H2O2, N2H4, and l -cysteine catalyzed by poly(Ni(4-TMPyP)) film-modified electrodes

Electrochemical preparation of poly(nickel tetrakis(N-methyl-4-pyridyl)porphyrin) tetratosylate (poly-Ni(4-TMPyP)) produces stable and electrochemically active films in strong and weak basic aqueous solutions. These films were produced on glassy carbon and gold electrodes. The electrochemical quartz crystal microbalance and cyclic voltammetry were used to study the in situ growth of poly(Ni(4-TMPyP)) films. The electrochemical properties of poly(Ni(4-TMPyP)) films indicate that the redox process was confined in to the immobilized film. The electrochemical quartz crystal microbalance results showed an ion exchange reaction for the redox couple. The polymer films showed one new redox couple when transferred to strong and weak basic aqueous solutions and the formal potential was found to be pH dependent. The electrocatalytic oxidation of H₂O by a nickel tetrakis(N-methyl-4-pyridyl)porphyrin film-modified electrode was also performed. The mechanism of oxygen evolution was determined by cyclic voltammetry, chronoamperometry and rotating ring disc electrode methods. The oxygen evolution was determined by a bicatalyst system using hemoglobin, and iron tetrakis (N-methyl-2-pyridyl)porphyrin as catalyst to detect the oxygen by electrocatalytic reduction. The electrocatalytic oxidations of adenine, guanine, H₂O₂, N₂H₄, NH₂OH, and l-cysteine by the film-modified electrode obtained from water-soluble nickel porphyrin were also investigated.     

L‐Cysteine Voltammetry at a Carbon Paste Electrode Bulk‐Modified with Ferrocenedicarboxylic Acid

The electrochemical behavior of L ‐cysteine studied at the surface of ferrocenedicarboxylic acid modified carbon paste electrode (FDCMCPE) in aqueous media using cyclic voltammetry, differential pulse voltammetry and double potential step chronoamperometry. It has been found that under optimum condition (pH 8.00) in cyclic voltammetry, the oxidation of L ‐cysteine occurs at a potential about 200 mV less positive than that of an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α, and catalytic reaction rate constant, k_h were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of L ‐cysteine showed a linear dependent on the L ‐cysteine concentration and linear analytical curves were obtained in the ranges of 3.0×10^?5 M–2.2×10^?3 M and 1.5×10^?5 M–3.2×10^?3 M of L ‐cysteine concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (3σ) were determined as 2.6×10^?5 M and 1.4×10^?6 M by CV and DPV methods.     

Electrocatalytic oxidation of hydrazine at cobalt hexacyanoferrate- modified glassy carbon, Pt and Au electrodes

The electrocatalytic oxidation of hydrazine has been studied on glassy carbon, Pt and Au electrodes modified by cobalt hexacyanoferrate (CoHCF) using cyclic voltammetry and rotating disc techniques. It has been shown that the oxidation of hydrazine to nitrogen occurs at the potential coinciding with that of Co(II) to Co(III) transformation in a CoHCF film, where no oxidation signal is observed at a bare glassy carbon electrode. A Tafel plot, derived from RDE voltammograms, exhibits a slope of 150 mV, indicating a one-electron charge transfer process to be the rate-limiting step. The electrocatalytic efficiency of the modified electrode towards hydrazine oxidation depends on solution pH, and the optimum range was found to be located between pH 5 and pH 7. The kinetic behaviour and location of the electrocatalytic process were examined using the W.J. Albery diagnosis table, and it was concluded that the reaction has either a “surface” or a “layer” reaction mechanism. Pt- and Au-CoHCF-modified electrodes show no significant electrocatalytic activity towards hydrazine oxidation. Received: 25 April 1997 / Accepted: 12 August 1997     

Application of a palladium hexacyanoferrate film-modified aluminum electrode to electrocatalytic oxidation of hydrazine.

A palladium hexacyanoferrate (PdHCF) film as an electrocatalytic material was obtained at an aluminum (Al) electrode by a simple electroless dipping method. The modified Al electrode demonstrated a well-behaved redox couple due to the redox reaction of the PdHCF film. The PdHCF film showed an excellent electrocatalytic activity toward the oxidation of hydrazine. The electrocatalytic oxidation of hydrazine was studied by cyclic voltammetry and rotating disk electrode voltammetry techniques. A calibration graph obtained for the hydrazine consisted of two segments (localized at concentration ranges 0.39-10 and 20-75 mM). The rate constant k and transfer coefficient alpha for the catalytic reaction and the diffusion coefficient of hydrazine in the solution D, were found to be 3.11 x 10(3) M(-1) s(-1), 0.52 and 8.03 x 10(-6) cm2 s(-1) respectively. The modified electrode was used to amperometric determination of hydrazine in photographic developer. The interference of ascorbic acid and thiosulfate were investigated and greatly reduced using a thin film of Nafion on the modified electrode. The modified electrode indicated reproducible behavior and a high level of stability during electrochemical experiments, making it particularly suitable for analytical purposes.     

Electrocatalytic Characteristics of Ferrocenecarboxylic Acid Modified Carbon Paste Electrode in the Oxidation and Determination of L‐Cysteine

The electrochemical behavior of L ‐cysteine studied at the surface of ferrocenecarboxylic acid modified carbon paste electrode (FCMCPE) in aqueous media using cyclic voltammetry and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00) in cyclic voltammetry, the oxidation of L ‐cysteine is occurs at a potential about 580 mV less positive than that an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α and catalytic reaction rate constant, K′_h were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of L ‐cysteine showed a linear dependent on the L ‐cysteine concentration and linear calibration curves were obtained in the ranges of 10^?5 M–10^?3 M and 4.1×10^?8 M–3.7×10^?5 M of L ‐cysteine concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (2δ) were determined as 2.4×10^?6 M and 2.5×10^?8 M by CV and DPV methods. This method was also examined for determination of L ‐cysteine in some samples, such as Soya protein powder, serum of human blood by using recovery and standard addition methods.     

Electrocatalytic Oxidation of Hydrazine at the Poly(Glutamic Acid) Chemically Modified Electrode and Its Amperometric Determination

ABSTRACT

The electrochemical polymerization of glutamic acid at the glassy carbon electrode was investigated in phosphate buffer solution by cyclic voltammetry. The applied voltage range, pH of electrolyte, cyclic number were explored for optimal polymerization conditions. The resulting film exhibits an electrocatalytic ability to hydrazine, reducing the overpotential by 500mV. The electrocatalytic response of hydrazine is evaluated with regard to pH, scan rate, applied voltage, hydrazine concentration and other variables. The rate constant of the catalytic reaction was 1.2 × 10⁴ M^?1.s^?1. When used as amperometric detector, the modified electrode yields a detection limit of 1 × 10^?8 M hydrazine. The electrode is rather stable even after use for a month and a reproducible response was obtained.