Amperometric Detection of Histamine with a Pyrroloquinoline‐Quinone Modified Electrode

A modified glassy carbon (GC) electrode was developed for the amperometric detection of biogenic amines, particularly histamine. The electrode was modified with the co‐enzyme pyrroloquinoline quinone (PQQ) by entrapment during electropolymerziation of pyrrole to form polypyrrole (PPy). This method formed a thin film on the electrode surface possessing very good stability with a shelf‐life exceeding one month without loss of signal. Optimal conditions for the PQQ/PPy electrode were determined and a linear response was found for histamine in phosphate buffer (pH 6) at +550 mV from 40 to 170 mg L^?1 with a limit of detection (S/N≥3) of 38 mg L^?1. The practical linear range offered by this method suggests ideal use for spoilage detection in fermented foods.     

Amperometric L‐cysteine Sensor Using a Gold Electrode Modified with Thiolated Catechol

A thiolated catechol (CA) consisting of 1,6‐Hexanedithiol (HDT) and CA was modified on a gold (Au) electrode to obtain an amperometric L‐cysteine sensor with detection limit of 60.6 nM. The preparation of thiolated CA was conducted via a thiol addition between HDT and electro‐oxidized CA (EOCA). Briefly, the thiol addition reaction was accomplished by potential cycling of HDT/Au electrode in 0.1 M phosphate buffer (PB, pH 7.2) containing CA, and an EOCA‐HDT/Au electrode was produced. The obtained EOCA‐HDT/Au electrode exhibits a pair of well‐defined redox peaks (at 0.22/0.10 V) of o‐quinone moiety, which effectively mediates the oxidation of L‐cysteine in a 0.1 M PB (pH 7.2), with an over‐potential decrease by ca. 0.12 V (versus bare Au electrode). Electrochemical quartz crystal microbalance, cyclic voltammetry and surface‐enhanced Raman spectra were used to study relevant processes and/or film properties. The amperometric L‐cysteine sensor has good anti‐interferent ability and reproducibility. It also has acceptable recovery for detection of L‐cysteine in urine samples.     

Electrochemical Detection of Persulfate at the Modified Glassy Carbon Electrode with Nanocomposite Containing Nano‐Ruthenium Oxide/Thionine and Nano‐Ruthenium Oxide/Celestine Blue

The present study describes the fabrication of a sensitive amperometric sensor for the determination of persulfate. The immobilization surface was prepared by modifying a glassy carbon (GC) electrode with a nanocomposite containing ruthenium oxide (RuOx) nanoparticles and thionine (TH) or celestin blue (CB). The modified electrodes indicated excellent electrocatalytic activity toward persulfate reduction at a potential of +0.1 V. The proposed sensor showed detection limits of 1.46 µM for the GC/RuOx/TH modified electrode and 2.64 µM for the GC/RuOx/CB modified electrode. The sensitivities were obtained as 3 nA µM^?1 at a concentration range of 10 µM to 11 mM for the GC/RuOx/TH modified electrode and 1 nA µM^?1 at a concentration range of 10 µM to 6 mM for the GC/RuOx/CB modified electrodes.     

Direct Voltammetry of Copper,Zinc‐Superoxide Dismutase Immobilized onto Electrodeposited Nickel Oxide Nanoparticles: Fabrication of Amperometric Superoxide Biosensor

Direct electron transfer of immobilized copper, zinc‐superoxide dismutase (SOD) onto electrodeposited nickel‐oxide (NiOx) nanoparticle modified glassy carbon (GC) electrode displays a well defined redox process with formal potential of ?0.03 V in pH 7.4. Cyclic voltammetry was used for deposition of (NiOx) nanoparticles and immobilization of SOD onto GC electrode. The surface coverage (Γ) and heterogeneous electron transfer rate constant (k_s) of immobilized SOD are 1.75×10^?11 mol cm^?2 and 7.5±0.5 s^?1, respectively. The biosensor shows a fast amperometric response (3 s) toward superoxide at a wide concentration range from 10 µM to 0.25 mM with sensitivity of 13.40 nA µM^?1 cm^?2 and 12.40 nA µM^?1 cm^?2, detection limit of 2.66 and 3.1 µM based on anodically and cathodically detection. This biosensor exhibits excellent stability, reproducibility and long life time.     

Au‐TiO2/Graphene Nanocomposite Film for Electrochemical Sensing of Hydrogen Peroxide and NADH

We describe a simple method for preparing Au‐TiO₂/graphene (GR) nanocomposite by deposition of Au nanoparticles (NPs) on TiO₂/GR substrates. The as‐prepared Au‐TiO₂/GR was characterized by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The presence of Au NPs on TiO₂/GR surface remarkably improves the electrocatalytic activity towards the oxidation of hydrogen peroxide (H₂O₂) and β‐nicotinamide adenine dinucleotide (NADH). The Au‐TiO₂/GR modified glassy carbon (GC) electrode exhibits good amperometric response to H₂O₂ and NADH, with linear range from 10 to 200 µM and 10 to 240 µM, and detection limit of 0.7 and 0.2 µM, respectively.     

Electrochemical Determination of Superoxide Based on Cytochrome c Immobilized on DDAB‐Modified Powder Microelectrode

Abstract

Cytochrome c was immobilized at didodecyldimethylammonium bromide (DDAB)‐modified powder microelectrode and presented quasi‐reversible electrochemistry. The apparent surface coverage of cytochrome c is greatly enhanced by using powder microelectrode technique, which is 1.21×10^?8 mol/cm², more than one to three orders of magnitude larger than that obtained with thiol and DNA‐modified Au electrode. The cytochrome c modified powder microelectrode was applied for the amperometric determination of superoxide generated by the reaction of hypoxanthine with xanthine oxidase (XOD) in the presence of dioxygen.

The detection sensitivity of the modified powder microelectrode is 0.74 µA/cm² µM, which is larger than that reported in previous publications. The detection limit of the modified powder microelectrode (PME) is 0.5 µM, and the linear detection range is 0.86～5.93 µM (values of the concentration are all in terms of hypoxanthine concentration in the solution).     

Detection of V-type nerve agent degradation products at electrodes modified by PPy/PQQ using CaCl2 as supporting electrolyte

Electrochemical detection without derivatization was used to detect thiol-containing degradation products of V-type nerve agents. Electropolymerization of pyrrole was used for entrapment of the biocatalyst PQQ to produce a sensor. Various parameters which affect the detection processes such as the type of the supporting electrolyte used during electrodeposition and the thickness of the polypyrrole film were examined and optimized. Electocatalytic oxidation of thiols by the PPy/PQQ electrode was strongly affected by the presence of Ca²⁺ cations during electrodeposition of the PPy/PQQ. Cyclic voltammetry, linear sweep voltammetry and amperometry have been used for electrode characterization. Amperometric detection of the V-type nerve agent thiol degradation products 2-(dimethylamino)ethanethiol (DMAET) and 2-(diethylamino)ethanethiol (DEAET) was performed at 0.38 V. Linear calibration plots were observed for these compounds. The detection limits of 4.5 and 3 μM were obtained for DMAET and DEAET respectively, with sensitivities of 1.18 and 1.37 nA μM⁻¹ cm⁻².     

Naphthalene Diimide Carrying Two Cysteine Termini at Both Imide Linkers as a Molecular Staple

Naphthalene diimide ( 1 ) carrying cysteines at the termini of amide substituents were synthesized to act as a molecular staple of double stranded DNA. Since 1 is able to bind to double stranded DNA with threading intercalation, the complex of 1 with double stranded DNA can be topologically immobilized on a gold surface through the S? Au linkage as confirmed by cyclic voltammetric experiment. Ferrocenyl‐double stranded 23‐mertic oligonucleotide, dsFcODN, was immobilized on gold electrode with 1.0×10¹² molecules cm^?2 when electrode was treated with 2.0 µM dsFcODN and 4.0 µM 1 for 1 h at room temperature. The coverage density was similar to that obtained for the terminal thiol‐modified oligonucleotide. Compound 1 was applied to detect the 321‐meric PCR product of P. gingivalis, which is important in the diagnosis of periodontal disease. This experiment, coupled with the use of ferrocenylnaphthalene diimide, FND as electrochemical indicator for double stranded DNA, resulted in quantitative detection of PCR product within the range of 10 pg µL^?1–10 ng µL^?1 (15 nM–15 µM). The 1 and FND established a simple and rapid detection method of double stranded PCR product with a detection limit of 10 pg µL^?1 (15 nM).     

Simultaneous Determination of Ranitidine and Metronidazole at Glassy Carbon Electrode Modified with Single Wall Carbon Nanotubes

Single‐walled carbon nanotubes(SWCNTs) were dispersed into DMSO, and a SWCNTs‐film coated glassy carbon electrode was achieved via evaporating the solvent. The results indicated that CNT modified glassy carbon electrode exhibited efficiently electrocatalytic reduction for ranitidine and metronidazole with relatively high sensitivity, stability and life time. Under conditions of cyclic voltammetry, the potential for reduction of selected analytes is lowered by approximately 150 mV and current is enhanced significantly (7 times) in comparison to the bare glassy carbon electrode. The electrocatalytic behavior is further exploited as a sensitive detection scheme for these analytes determinations by hydrodynamic amperometry. Under optimized condition in amperometric method the concentration calibration range, detection limit and sensitivity were about, 0.1–200 μM, detection limit (S/N=3) 6.3×10^?8 mol L^?1 and sensitivity 40 nA/μM for metronidazole and 0.3–270 μM 7.73×10^?8 mol L^?1 and 25 nA/μM for ranitidine. In addition, the ability of the modified electrode for simultaneous determination of ranitidine and metronidazole was evaluated. The proposed method was successfully applied to ranitidine and metronidazole determination in tablets. The analytical performance of this sensor has been evaluated for detection of these analytes in serum as a real sample.     

Electorchemical Studies of Cytochrome c on Electodes Modified by Single—Wall Carbon Naotubes

Single-wall carbon nanotubes(SWNTs) modified gold electrodes were prepared by using two different methods.The electrochemical behavior of cytochrome c on the modified gold electrodes was investigated.The first kind of SWNT-modified electrode (noted as SWNT/Au electrode)was prepared by the adsorption of carboxylterminated SWNTs from DMF dispersion on the gold electrode.The oxidatively processed SWNT tips were covalently modified by coupling with amines (AET) to form amide linkage.Via Au-S chemical bonding,the self-assembled monolayer of thiol-unctionalized nanotubes on gold surface was fabricated so as to prepare the others SWNT-modified electrode (noted as SWNT/AET/Au electrode).It was shown from cyclic voltammetry cxperiments that cytochrome c exhibited direct electrochemical responses on the both electrodes, but only the current of controlled diffusion existed on the SWNT/Au electrode while both the currents of controlled diffusion and adsorption of cytochrome c occurred on the SWNT/AET/Au electrode.Photoelastic Modulation Infared Reflection Absorpthion Spectroscopy (PEM-IRRAS) and Quartz Crystal Microbalance (QCM) were employed to verify the adsorption of SWNTs on the gold electrodes.The results proved that SWNTs could enhance the direct electron transfer proecss between the electrodes and redox proteins.     

Flow‐Injection Pulsed‐Amperometric Determination of Free Glycerol in Biodiesel at a Gold Electrode

This work reports the highly‐sensitive amperometric determination of free glycerol in biodiesel at a gold electrode adapted in a flow‐injection analysis (FIA) cell. The amperometric method involved the continuous application of three sequential pulses to the working electrode (+250 mV, +700 mV, and ?200 mV, for 100 ms each). This sequence of potential pulses eliminated electrode passivation and dramatically increased the analytical signal. The proposed FIA‐amperometric method presented low relative standard deviation between injections (1.5 %, n=15), high analytical frequency (85 h^?1), satisfactory recovery values (93–118 %) for spiked samples, wide linear range (from 1 to 300 µmol L^?1), and low detection limit (0.5 µmol L^?1).     

Immobilization of Enzymes on the Nano‐Au Film Modified Glassy Carbon Electrode for the Determination of Hydrogen Peroxide and Glucose

A new enzyme‐based amperometric biosensor for hydrogen peroxide was developed relying on the efficient immobilization of horseradish peroxidase (HRP) to a nano‐scaled particulate gold (nano‐Au) film modified glassy carbon electrode (GC). The nano‐Au film was obtained by a chitosan film which was first formed on the surface of GC. The high affinity of chitosan for nano‐Au associated with its amino groups resulted in the formation of nano‐Au film on the surface of GC. The film formed served as an intermediator to retain high efficient and stable immobilization of the enzyme. H₂O₂ was detected using hydroquinone as an electron mediator to transfer electrons between the electrode and HRP. The HRP immobilized on nano‐Au film maintained excellent electrocatalytical activity to the reduction of H₂O₂. The experimental parameters such as the operating potential of the working electrode, mediator concentration and pH of background electrolyte were optimized for best analytical performance of amperometry. The linear range of detection for H₂O₂ is from 6.1×10^?6 to 1.8×10^?3 mol L^?1 with a detection limit of 6.1 μmol L^?1 based on signal/noise=3. The proposed HRP enzyme sensor has the features of high sensitivity (0.25 Almol^?1cm^?2), fast response time (t_90%≤10 s) and a long‐term stability (>1 month). As an extension, glucose oxidase (GOD) was chemically bound to HRP‐modified electrode. A GOD/HRP bienzyme‐modified electrode formed in this way can be applied to the determination of glucose with satisfactory performance.     

Amperometric Detection and Quantification of 8‐Hydroxy‐2′‐deoxyguanosine (8‐OHdG) Using Dendrimer Modified Electrodes

8‐Hydroxy‐2′‐deoxyguanosine (8‐OHdG) detection by high performance liquid chromatography (HPLC) with amperometric detection was studied using a Au electrode modified with different dendrimer based thin films. Gold electrode is thiol‐modified, forming self‐assembled monolayers on which different generation PAMAM dendrimers with terminal functional groups ? COOH and ? NH₂ have been attached using peptidic bonds. Results obtained in synthetic samples show low limits of detection and quantification for 8‐OHdG (1.2×10^?9 and 3.7×10^?9 M respectively), with matrix interference elimination, thus avoiding sample pretreatment. Best results are obtained with electrodes modified with aliphatic amino thiols and 3.5 and 4.5 generation carboxylated dendrimers (Au/AET/DG^3.5 and Au/AET/DG^4.5), demonstrating that these materials constitute a good alternative for 8‐OHdG determination in biological fluids.     

Fabrication of Bienzymatic Glucose Biosensor Based on Novel Gold Nanoparticles‐Bacteria Cellulose Nanofibers Nanocomposite

An exploration of gold nanoparticles–bacterial cellulose nanofibers (Au‐BC) nanocomposite as a platform for amperometric determination of glucose is presented. Two enzymes, glucose oxidase (GOx) and horseradish peroxidase (HRP) were immobilized in Au‐BC nanocomposite modified glassy carbon electrode at the same time. A sensitive and fast amperometric response to glucose was observed in the presence of electron mediator (HQ). Both of GOx and HRP kept their biocatalytic activities very well in Au‐BC nanocomposite. The detection limit for glucose in optimized conditions was as low as 2.3 µM with a linear range from 10 µM to 400 µM. The biosensor was successfully applied to the determination of glucose in human blood samples.     

Facile Synthesis of Leaf‐Like CuO Nanoparticles and Their Application on Glucose Biosensor

An efficient amperometric biosensor based on well‐crystallized leaf‐like CuO nanoparticles for detecting glucose has been proposed. The leaf‐like CuO nanoparticles, synthesized by a simple one‐step hydrothermal method, were characterized by X‐ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscopy (TEM) for the morphology study. Under the optimal condition, the electrochemical behaviour of the leaf‐like CuO nanoparticles modified electrode for detection of glucose exhibited high sensitivity of 246 µA/mM/cm², short response time (within 5 s), linear dynamic range from 1.0 to 170 µM (R²=0.9995), and low limit of detection (LOD) (S/N=3) of 0.91 µM. The high sensitivity, good reproducibility, stability, and fast amperometric sensing towards oxidation of glucose, make this biosensor promising for future application.     

A Highly Sensitive and Selective Multiwall Carbon Nanotubes/Nafion/Au Microarrays Electrode for Dopamine Determination

This work presents the fabrication of Nafion (Nf) or Nafion/Multiwalled Carbon Nanotubes (Nf/MWCNTs) modified gold microarray (Au‐µA) and macro‐(Au‐M)electrode biosensors. The surface morphologies of the above electrodes were examined using SEM. The catalytic properties of the above electrodes towards dopamine were tested using square wave voltammetric technique. The Nf/MWCNT/Au‐µA electrode exhibited a wide range (0.1–1000 nM) of linearity among the other electrodes. The LOD of Nf/MWCNT/Au‐µA electrode was 50 pM for dopamine in the presence of 5000 µM ascorbic acid. Therefore, the Nf/MWCNT/Au‐µA biosensor was applied for the determination of dopamine in human serum.     

Electrocatalytic Oxidation of Formaldehyde on Copper Oxide Nano-crystalline Modified Glassy Carbon Electrode

This research found a cheap and efficient catalyst for electrooxidation of formaldehyde (HCHO). A CuO nano‐crystalline modified glassy carbon electrode (GCE) was fabricated and had an excellent electrocatalytic activity towards the oxidation of HCHO. Both the effect of potential scan rate and the effect of HCHO concentration on the electrocatalytic oxidation performance of the electrode were investigated. The amperometric current response of the electrode was proportional to HCHO concentration in the range of 1.0 µmol·L^?1–10.0 mmol·L^?1 with a detection limit (s/n=3) of 0.25 µmol·L^?1. The electrode was stable, showing the CuO nano‐crystlline is promising for applications in fuel cells and electrochemical sensors.     

N‐(3,4‐Dihydroxyphenethyl)‐3,5‐dinitrobenzamide‐Modified Multiwall Carbon Nanotubes Paste Electrode as a Novel Sensor for Simultaneous Determination of Penicillamine,Uric acid,and Tryptophan

N‐(3,4‐dihydroxyphenethyl)‐3,5‐dinitrobenzamide modified multiwall carbon nanotubes paste electrode was used as a voltammetric sensor for oxidation of penicillamine (PA), uric acid (UA) and tryptophan (TP). In a mixture of PA, UA and TP, those voltammograms were well separated from each other with potential differences of 300, 610, and 310 mV, respectively. The peak currents were linearly dependent on PA, UA and TP concentrations in the range of 0.05–300, 5–420, and 1.0–400 µmol L^?1, with detection limits of 0.021, 2.0, and 0.82 µmol L^?1, respectively. The modified electrode was used for the determination of those compounds in real samples.     

Sensitive and Rapid Flow Injection Amperometric Hydrazine Sensor using an Electrodeposited Gold Nanoparticle Graphite Pencil Electrode

A gold (Au) nanoparticle-modified graphite pencil electrode was prepared by an electrodeposition procedure for the sensitive and rapid flow injection amperometric determination of hydrazine (N₂H₄). The electrodeposited Au nanoparticles on the pretreated graphite pencil electrode surface were characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction spectroscopy, and electrochemical impedance spectroscopy. Cyclic voltammograms showed that the Au nanoparticle-modified pretreated graphite pencil electrode exhibits excellent electrocatalytic activity toward oxidation of hydrazine because the highly irreversibly and broadly observed oxidation peak at +600?mV at the pretreated graphite pencil electrode shifted to ?167?mV at the Au nanoparticle pretreated graphite pencil electrode; in addition, a significant enhancement in the oxidation peak current was obtained. Thus, the flow-injection (FI) amperometric hydrazine sensor was constructed based on its electrocatalytic oxidation at the Au nanoparticle-modified pretreated graphite pencil electrode. The Au nanoparticle-modified pretreated graphite pencil electrode exhibits a linear calibration curve between the flow injection amperometric current and hydrazine concentration within the concentration range from 0.01 to 100?µM with a detection limit of 0.002?µM. The flow injection amperometric sensor has been successfully used for the determination of N₂H₄ in water samples with good accuracy and precision.     

Fabrication of an Electrochemical L‐Cysteine Sensor Based on Graphene Nanosheets Decorated Manganese Oxide Nanocomposite Modified Glassy Carbon Electrode

The graphene nanosheets/manganese oxide nanoparticles modified glassy carbon electrode (GC/GNSs/MnOx) was simply prepared by casting a thin film of GNSs on the GC electrode surface, followed by performing electrodeposition of MnOx at applied constant potential. The GC/GNSs/MnOx modified electrode shows high catalytic activity toward oxidation of L ‐cysteine. Hydrodynamic amperometry determination of L ‐cysteine gave linear responses over a concentration range up to 120 µM with a detection limit of 75 nM and sensitivity of 27 nA µM^?1. The GC/GNSs/MnOx electrode appears to be a highly efficient platform for the development of sensitive, stable and reproducible L ‐cysteine electrochemical sensors.