Electrochemical Characteristics and Electrosensing of an Antiviral Drug,Entecavir via Synergic Effect of Graphene Oxide Nanoribbons and Ceria Nanorods

A sensitive electrochemical sensor was fabricated based on ceria‐graphene oxide nanoribbons composite (CeO₂‐GONRs) for an antiviral drug, entecavir (ETV). It was characterized by SEM, EDAX, AFM, IR and Raman spectroscopic techniques. The electrochemical behaviour of ETV was investigated by cyclic voltammetric, differential pulse voltammetric (DPV), linear sweep voltammetric (LSV) and square wave voltammetric (SWV) methods at CeO₂‐GONRs modified glassy carbon electrode. Good linearity was observed between the peak current and concentration of ETV in the range of 0.51 ‐ 100 μM with a detection limit of 0.042 μM in DPV method, 2.1 – 61.1 μM with a detection limit of 0.7 μM in LSV method and 0.1 ‐ 80 μM with a detection limit of 68.1 nM in SWV method. The proposed sensitive DPV method was successfully applied for the determination ETV in tablets and biological samples.     

Voltammetric Determination of 4‐Nitrophenol Using a Novel Type of Silver Amalgam Paste Electrode

A differential pulse voltammetric (DPV) method was developed for the determination of 4‐nitrophenol (4‐NP) at a newly developed silver amalgam paste electrode (AgA‐PE) in Britton–Robinson buffer pH 3.0. The electrode is based on a disposable plastic pipette tip filled with paste amalgam based on a mixture of mercury and fine silver powder (9 : 1, w/w). The experimental parameters, such as pH of Britton–Robinson buffer and activation and regeneration potential of the electrode surface were optimized. The reduction peak current dependences were linear for the concentration of 4‐NP from 0.2 to 100 μM. The method showed reproducible results with RSD (n=45) of 1.7%. The limit of determination (LOD) was 0.3 μM. The method was successfully applied for the direct determination of 4‐NP in drinking water.     

Electrodeposited Silver Nanoparticles on Carbon Ionic Liquid Electrode for Electrocatalytic Sensing of Hydrogen Peroxide

Silver nanoparticles (narrowly dispersed in diameter) were electrodeposited on carbon ionic liquid electrode (CILE) surface using a two‐step potentiostatic method. Potentiostatic double pulse technique was used as a suitable and simple method for controlling the size and morphologies of silver nanoparticles electrodeposited on CILE. The obtained silver nanoparticles deposited on CILE surface showed excellent electrocatalytic activity (low overpotential of ?0.35 V vs. Ag/AgCl) towards reduction of hydrogen peroxide. A linear dynamic range of 2–200 μM with an experimental detection limit of 0.7 μM (S/N=3) and reproducibility of 4.1% (n=5) make the constructed sensor suitable for peroxide determination in aqueous solutions.     

A Sensitive Sensor Based on Single‐walled Carbon Nanotubes: Its Preparation,Characterization and Application in the Electrochemical Determination of Drug Clorsulon in Milk Samples

Within this paper, a glassy carbon electrode modified with single‐walled carbon nanotubes (SWCNTs?GCE) was prepared, and employed for the determination of clorsulon (Clo), which is a frequently used veterinary drug against common liver fluke. The comprehensive topographical and electrochemical characterizations of bare GCE and SWCNTs?GCE were performed by atomic force microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. Significantly enhanced electrochemical characteristics of SWCNTs?GCE toward a ferrocyanide/ferricyanide redox couple was observed when compared to bare GCE. Further, the prepared sensor was applied for the voltammetric determination of Clo, which was electrochemically investigated for the first time in this work. Voltammetric experiments were performed using square‐wave voltammetry with optimized parameters in phosphate buffer solution, pH 6.8, which was selected as the most suitable medium for the determination of Clo. The corresponding current at approx. +1.1 V increased linearly with Clo concentration within two linear dynamic ranges of 0.75–4.00 μmol L^?1 (R²=0.9934) and 4.00–15.00 μmol L^?1 (R²=0.9942) with a sensitivity for the first calibration range of 0.76 μA L μmol^?1, a limit of detection of 0.19 μmol L^?1, and a limit of quantification of 0.64 μmol L^?1. The developed method was subsequently applied for quantitative analysis of Clo in milk samples with results proving high repeatability and recovery.     

Selective Voltammetric Detection of Uric Acid in the Presence of Ascorbic Acid at Well‐Aligned Carbon Nanotube Electrode

The voltammetric behaviors of uric acid (UA) and L ‐ascorbic acid (L ‐AA) were studied at well‐aligned carbon nanotube electrode. Compared to glassy carbon, carbon nanotube electrode catalyzes oxidation of UA and L ‐AA, reducing the overpotentials by about 0.028 V and 0.416 V, respectively. Based on its differential catalytic function toward the oxidation of UA and L ‐AA, the carbon nanotube electrode resolved the overlapping voltammetric response of UA and L ‐AA into two well‐defined voltammetric peaks in applying both cyclic voltammetry (CV) and differential pulse voltammetry (DPV), which can be used for a selective determination of UA in the presence of L ‐AA. The peak current obtained from DPV was linearly dependent on the UA concentration in the range of 0.2 μM to 80 μM with a correlation coefficient of 0.997. The detection limit (3δ) for UA was found to be 0.1 μM. Finally, the carbon nanotube electrode was successfully demonstrated as a electrochemical sensor to the determination of UA in human urine samples by simple dilution without further pretreatment.     

Carbon Paste Electrode Plated with Lead Film. Voltammetric Characteristics and Application in Adsorptive Stripping Voltammetry

A lead film plated in situ at a carbon paste support was tested as a novel, potential electrode for adsorptive stripping voltammetric determination of cobalt traces in an ammonia buffer solution. To show the practical applicability of the new electrode, a catalytic adsorptive Co system in a supporting electrolyte containing 0.1 M ammonia buffer, 5×10^?4 M nioxime and 0.25 M nitrite was selected and investigated as a model solution. Pb and Co ions were simultaneously accumulated in situ on the electrode surface: Pb ions electrochemically at ?1.3 V) and then at ?0.75 V, at which potential the Co(II)‐nioximate complex was also pre‐concentrated via adsorption. Instrumental parameters, such as the time of nucleation and formation of Pb film deposits, the time of accumulation of the Co‐nioxime complex at the PbF/CPE, and the procedures of electrode regeneration, were optimized to obtain good reproducibility and sensitivity of the Co response. The optimized procedure yields favorable and highly stable stripping responses with good precision (RSD=3% for a 5×10^?8 M Co) and good linearity (up to 5×10^?7 M, coefficient of determination, R=0.996). The detection limit was 4×10^?10 M Co (0.023 μg L^?1) for an accumulation time of 120 s. The method enables the determination of Co in the presence of high excesses of Ni or Zn. The voltammetric data were correlated with the structural characterization by scanning electron microscopy (SEM) and X‐ray fluorescence spectroscopy (XRF).     

A Simple,Efficient and Ultrasensitive Gold Nanourchin Based Electrochemical Sensor for the Determination of an Antimalarial Drug: Mefloquine

Mefloquine (MQ) is a quinoline based antimalarial drug, which is potent against multiple drug‐resistant Plasmodium falciparum . It is widely prescribed for the prophylactic treatment of malaria. Due to extensive usage of MQ, constant monitoring of the drug level in human body is of paramount importancein order to ensure that optimum drug exposure is achieved. The present work describes a gold nanourchins (AuNUs) based electrochemical sensor for the determination of MQ.AuNUs were synthesized via seed‐mediated method and characterized using ultraviolet‐visible spectroscopy, energy‐dispersive X‐ray spectroscopy, field emission scanning electron microscopy, zeta‐sizer and electrochemical techniques (electrochemical impedance spectroscopy and cyclic voltammetry). Fabrication of the sensor was done by drop‐coating the synthesized AuNUs onto a glassy carbon electrode. The fabricated sensor exhibited enhanced voltammetric response, which was attributed to the excellent conductivity and high surface area of AuNUs. Under optimum square wave voltammetric conditions, the sensor displayed two linear response ranges (from 2.0×10⁻⁹ to 1.0×10⁻⁶ M and from 1.0×10⁻⁶ to 1.0×10⁻³ M) with a detection limit of 1.4 nM. The electrode demonstrated good reproducibility, stability and selectivity over common interferents. The utility of the sensor was successfully assessed for quantification of the drug in pharmaceutical preparation and spiked human urine sample. Thus, the present study demonstrates a promising approach for determination of MQ with practical utility in quality control and clinical analysis.     

Voltammetric Determination of Allura Red AC onto Carbone-paste Electrode Modified by Silica with Embedded Cetylpyridinium Chloride

In current study the carbon-paste electrode modified by silica with embedded cetylpyridinium chloride for determination of Allura Red AC have been developed. The optimal conditions were determined to be for the square-wave voltammetric quantification: pH=2, E_ads=300 mV, t_ads=300 s, amplitude – 40 mV, frequency – 25 Hz and potential scan rate is 250 mV sec⁻¹. The calibration plot has linearity in the concentration ranges 0.04–0.2 μM and 0.2–1.00 μM. The LOD and LOQ are equal to 0.005 μM and 0.015 μM respectively. The crafted sensor has been applied successfully to model solutions and in jelly candies analysis with RSD no more than 10 %.     

Silver Microelectrode Arrays for Direct Analysis of Hydrogen Peroxide in Low Ionic Strength Samples

Silver microelectrode arrays are fabricated by photolithography for a one-step analysis of H₂O₂ in low ionic strength samples. The effects of electrode length, width, band-to-band separation, connection height, and adhesion layer are evaluated. The developed sensor shows excellent repeatability (RSD=1.20 % (n=5)) and reproducibility (RSD=1.12 % (n=5)) with the linear range of 0.0–10.0 mM, the sensitivity of 9.84±0.34 μA mM⁻¹, and the detection limit of 22.69 μM. The sensor has been successfully applied to detect H₂O₂ directly without the addition of supporting electrolyte in synthetic urine, tap water, drinking water, and milk samples.     

Amperometric Detection of Morphine at Preheated Glassy Carbon Electrode Modified with Multiwall Carbon Nanotubes

A highly sensitive and fast responding sensor for the determination of morphine is described. The multiwall carbon nanotubes immobilize on preheated glassy carbon electrode (5 min at 50 °C) by gently rubbing of electrode surface on a filter paper supporting the carbon nanotubes.The results indicated that carbon nanotubes(CNTs) modified glassy carbon electrode exhibited efficiently electrocatalytic oxidation for morphine with relatively high sensitivity, stability and long life. Under conditions of cyclic voltammetry, the potential for oxidation of morphine is lowered by approximately 100 mV and the current is enhanced significantly (10 times) in comparison to the bare glassy carbon electrode at wide pH range (2–9). The electrocatalytic behavior is further exploited as a sensitive detection scheme for morphine determination by hydrodynamic amperometry. Under the optimized conditions the calibration plots are linear in the concentration range 0.5–150 μM with the calculated detection limit (S/N=3) of 0.2 μM and sensitivity of 10 nA/μM and a relative standard deviation (RSD) of 2.5% (n=10). The amperometric response is extremely stable, with no loss in sensitivity over a continual 30 min operation. Such attractive ability of multiwall carbon nanotubes (MWCNTs) modified GC electrode, suggests great promise for a morphine amperometric sensor. Finally the ability of the modified electrode was evaluated for simultaneous determination of morphine and codeine.     

A new route for simple and rapid determination of hydrogen peroxide in RAW264.7 macrophages by microchip electrophoresis

A new method using MCE with LIF detection was developed for the determination of hydrogen peroxide (H₂O₂). Bis(p‐methylbenzenesulfonyl)dichlorofluorescein, a new fluorogenic reagent synthesized by our laboratory was employed as a labeling reagent, the derivatization reaction was performed in 0.10 M HEPES buffer (pH 7.4) for 30 min at 37°C. The detection of H₂O₂ was accomplished in 55 s, using a 40 mM HEPES buffer, 20% mannitol, pH 7.4, on a glass microchip. The RSDs of migration time and peak area were 1.8 and 3.7%, respectively. Method validation showed the linear response ranging from 0.50 to 50 μM with an LOD (S/N=3) of 0.20 μM (19.1 amol). The proposed method was applied to determine H₂O₂ in phorbol myristate acetate‐stimulated RAW264.7 macrophages, the concentration of H₂O₂ was found to be 1.86±0.05 μM; recoveries for macrophage samples were from 96.7 to 97.8%, within‐days and between‐days accuracies were 4.5% (n=5) and 6.8% (n=5), respectively.     

Selective and Sensitive Voltammetric Determination of Dopamine in Blood by Electrochemically Treated Pencil Graphite Electrodes

Preparation of electrochemically treated pencil graphite (ETPG) electrode and its application for the determination of DA in the presence of ascorbic (AA) and uric (UA) acids were investigated. Several important parameters were worked to control the performance of the ETPG electrode which showed a high selectivity and sensitivity toward DA. A linear relationship was obtained for dopamine (DA) over the concentration range of 0.01 and 5.0 μM with a detection limit of 0.31 nM in the presence of AA and UA. The fabrication reproducibility of the ETPG electrodes (n=10) showed an acceptable reproducibility with a RSD of 2.0% for 5.0 μM DA. The determination of DA in blood serum without any pretreatment and dilution has been reported for the first time in this work.     

Improved Sensing of Capsaicin with TiO2 Nanoparticles Modified Epoxy Graphite Electrode

The presented research focuses on the electrochemical determination of capsaicin, a lipophilic alkaloid which originates hotness in chili peppers. An electrochemical sensor based on epoxy‐graphite composite with the modification of titanium dioxide (TiO₂) nanoparticles is developed for the determination of this alkaloid. The measurements were carried out in glycine buffer at pH 2.5 using cyclic voltammetry. Two linear concentration ranges were obtained from 6 to 75 μM (R=0.99) and from 12 to 138 μM, with a detection limit of 5.34 μM and 11.3 μM capsaicin, for 1^st and 2^nd oxidation peak, respectively. The main advantage of developed sensor is its repeatability and robustness against fouling; the relative standard deviation (RSD) value was 2.53 % (n=10). This voltammetric sensing procedure has successfully been applied to quantify capsaicin in various real samples such as hot chili sauce and pharmaceutical preparations.     

Incorporation of graphene oxide–NiO nanocomposite and <Emphasis Type="Italic">n</Emphasis>-hexyl-3-methylimidazolium hexafluoro phosphate into carbon paste electrode: application as an electrochemical sensor for simultaneous determination of benserazide,levodopa and tryptophan

The benserazide (BZ) and levodopa (LD) are two important catechol drugs to inhibit dopamine production outside the brain. On the other hand, BZ is effective on tryptophan (Trp) metabolism as an inhibitor aromatic amino acid decarboxylase. A voltammetric sensor based on carbon paste electrodes modified with graphene oxide–NiO nanocomposite and n-hexyl-3-methylimidazolium hexafluoro phosphate (n-H-3MIHF) as a binder is proposed to detect and quantify of BZ, LD and Trp in drug and urine samples. In square-wave voltammetry technique, BZ, LD and Trp were given sensitive oxidation peaks at 156, 312 and 740 mV, respectively. At a best electrochemical conditions, the enhanced oxidation peak currents represented the excellent analytical performance of simultaneous detection of BZ, LD and Trp in the ranges of 0.1–600, 0.1–700 and 5.0–700 μM, with a low limit of detection of 0.05 μM for BZ, 0.05 for LD and 1.0 μM for Trp (S/N = 3), respectively. To further validate its possible application, the proposed sensor was successfully used for the determination of above compounds in tablet and urine with satisfactory results.     

Electrocatalytic determination of penicillamine using multiwall carbon nanotubes paste electrode and chlorpromazine as a mediator

In this study, we describe the application of carbon paste electrode modified with multiwall carbon nanotubes as a voltammetric sensor for determination of penicillamine (PA) in the presence of chlorpromazine as a mediator. This modified electrode showed very efficient electrocatalytic activity for the anodic oxidation of PA. The peak current of linear sweep voltammograms of PA increased linearly with it’s concentration in the range of 0.5–500 μM PA. The detection limit for PA was 0.2 μM. The RSDs for 1.0 and 10.0 μM PA were 1.1 and 1.7%, respectively. The proposed sensor was successfully applied for the determination of PA in human urine and tablet.     

Electrochemically Degraded Dopamine Film for the Determination of Dopamine

A dopamine (DA) polymer was deposited electrochemically on to a glassy carbon (GC) surface until the electrode surface was passivated. The DA film on the GC surface was re‐formed for high sensitivity and reproducibility by electrochemical degradation. The re‐formed electrode was sensitive and selective in the determination of DA in the presence of ascorbic acid. The linear range obtained by square‐wave voltammetry was between 0.1 and 2.1 μM (R=0.996, n=6) with a sensitivity of 1.2 μA μM^?1 and a detection limit (S/N=3) of 0.04 μM. The electropolymerized DA film was stable and the re‐formed electrode was reproducible for DA determination.     

Electrochemical Behavior and Electroanalytical Determination of Indole‐3‐Acetic Acid Phytohormone on a Boron‐Doped Diamond Electrode

In this work, a boron‐doped diamond (BDD) electrode was used for the electroanalytical determination of indole‐3‐acetic acid (IAA) phytohormone by square‐wave voltammetry. IAA yielded a well‐defined voltammetric response at +0.93 V (vs. Ag/AgCl) in Britton–Robinson buffer, pH 2.0. The process could be used to determine IAA in the concentration range of 5.0 to 50.0 µM (n=8, r=0.997), with a detection limit of 1.22 µM. The relative standard deviation of ten measurements was 2.09 % for 20.0 µM IAA. As an example, the practical applicability of BDD electrode was tested with the measurement of IAA in some plant seeds.     

Voltammetric Behavior of Arsenic(III) in the Presence of Sodium Diethyl Dithiocarbamate and Its Determination in Water and Highly Saline Samples by Adsorptive Stripping Voltammetry

This paper describes the voltammetric behavior of As(III) at the hanging mercury drop electrode (HMDE) in the presence of sodium diethyl dithiocarbamate (SDDC) and a new voltammetric method for the determination of As(III) at trace levels. The method is based on the adsorptive deposition of a As(III) complex with SDDC at ?0.45 V (vs. Ag/AgCl) on the HMDE in acidic medium of 0.01 mol L^?1 HCl (pH 2.0) and its cathodic stripping during the potential scan (100 mV s^?1). The linear range for the determination of As(III) in the presence of SDDC (4 μmol L^?1) in water samples was between 1 and 10 μg L^?1 for a deposition time of 300 s (r=0.994) and between 10 and 100 μg L^?1 for a deposition time of 60 s (r=0.999). For the determination of As(III) in dialysis concentrate samples, the linear range was between 5 and 25 μg L^?1 for a deposition time of 180 s (r=0.992) and between 10 and 100 μg L^?1 for a deposition time of 60 s (r=0.996). Detection limits of 0.3 and 2.2 μg L^?1 in water and dialysis concentrate samples were calculated for the method using a deposition time of 300 and 180 s, respectively. Recovery values between 93.0 and 110.0% for As(III) added to deionized, mineral, seawater (synthetic and real) and dialysis concentrate samples prove the satisfactory accuracy and applicability of the procedure.     

Potential Application of Carbon-based Electrical Sensor for the Highly Sensitive Diltiazem HCl Quantification in its Pharmaceutical Products and Biological Samples

Diltiazem (DTZ) hydrochloride, a calcium channel blocker compound, is a very well-known drug used by many clinicians to treat important diseases playing a role in increased morbidity and mortality among adults worldwide, namely hypertension, cardiac arrhythmia, and ischemic heart disease (angina pectoris). These diseases are a common public health concern, implying that the construction of a specific, accurate, and simple sensor for DTZ determination is needed. Herein, an innovative, portable, and sensitive modified carbon paste electrode (MCPE) was seamlessly developed based on the affordable green compound N-bromosuccinimide (NBS) as a sensing material and tricresyl phosphate as a solvent mediator for the voltammetric determination of DTZ. The proposed NBS-MCPE exhibited an excellent electrocatalytic activity towards the oxidation of DTZ molecules in a phosphate buffer solution of pH 5.0 in presence of 20 μM sodium dodecyl sulfate to improve the developed sensor performance. The sensor was found to respond linearly to the DTZ drug over a wide concentration ranging from 1 μM to 300 μM with a low limit of detection. LSV and EIS measurements were also used to scrutinize our sensor, in addition to using scanning electron microscopy and energy dispersive X-ray analysis techniques for its surface morphology inspection before and after soaking in the drug-containing solution. The applicability of the proposed sensor for the rapid, sensitive, and selective determination of DTZ in pharmaceutical preparation and human urine samples was assessed and the obtained results were compared with that of the reported HPLC analytical method.     

Determination of Ethylenethiourea (ETU) at Trace Levels in Water Samples by Cathodic Stripping Voltammetry

A stripping voltammetric method for the determination of ethylenethiourea in water samples is described based on its adsorptive deposition at the hanging mercury drop electrode (HMDE). In a borate buffer (pH 9.0) as supporting electrolyte, ETU is deposited at +100 mV (vs. Ag/AgCl) and stripped during the cathodic scan. The linear range for the measurements was from 2.0 to 100 μg L^?1, with a detection limit calculated as 1.4 μg L^?1 after a deposition time of 300 s and a RSD of 1.9% (n=5) for 50 μg L^?1 of ETU measured. The interferences of some organic compounds and metallic ions were tested. Recoveries between 93 and 110% were obtained using the standard addition method for spiked samples of natural and drinking waters. The method is rapid and applicable in the monitoring of ETU residues in water samples.