Determination of Paracetamol in Presence of Ascorbic Acid in Pharmaceutical Products by Scanning Electrochemical Microscopy

The selective amperometric determination of paracetamol in pharmaceutical formulations containing ascorbate was achieved by removing the interfering species in the diffusion layer created between a platinum substrate and a disc microelectrode in a Scanning Electrochemical Microscopy (SECM) configuration, while the target analyte was kept unconsumed. After complete depletion of ascorbate, paracetamol was detected at the SECM tip in a free‐interference solution zone. The influence of the substrate potential and the gap distance on the efficiency of ascorbate removal was systematically examined. The effectiveness of the device towards the determination of paracetamol in pharmaceutical samples was evaluated and under optimal conditions the results obtained agreed well with the labeled value.     

Evaluation of Redox Activity of Human Myocardium‐derived Mesenchymal Stem Cells by Scanning Electrochemical Microscopy

In this study the redox activity of human myocardium‐derived mesenchymal stem cells (hmMSC) were investigated by redox‐competition (RC‐SECM) and generation‐collection (GC‐SECM) modes of scanning electrochemical microscopy (SECM), using 2‐methylnaphthalene‐1,4‐dione (menadione, MD) as a redox mediator. The redox activity of human healthy and dilated hmMSCs was evaluated by measuring reduction of MD. Measurements were performed by approaching and retracting the UME from the surface of growing hmMSC cells. The current study shows that the RC‐SECM mode can be applied to investigate integrity of cell membranes, whereas the most promising results were observed by using the GC‐SECM mode and applying the Hill's equation for the calculation/fitting of dependencies of electrical current vs menadione concentration. The calculated apparent Michaelis constant (K_M) for the production of menadiol (MDH₂) in the pathological hmMSC cells was 14.4 folds higher compared to that of the healthy hmMSC revealing the lover redox activity of pathological cells. Moreover, the calculated Hill's coefficient n shows a negative cooperative binding between MD and healthy hmMSC and positive cooperative binding between MD and pathological hmMSC. It means that healthy hmMSC is of lower affinity to MD, which is also related to the better membrane integrity of healthy cells. Data of this study demonstrate that SECM can be applied to investigate intracellular redox and membrane changes ongoing in human dilated myocardium‐derived hmMSC in order to improve their functioning and further regenerative potential.     

Evaluation of Enzymatic Kinetics of GOx‐based Electrodes by Scanning Electrochemical Microscopy at Redox Competition Mode

Glucose oxidase (GOx) is an enzyme, which is used for the development of enzymatic biofuel cells. Therefore in this research redox competition mode of scanning electrochemical microscopy (RC‐SECM) was applied for the investigation of glucose oxidase (GOx) catalyzed reaction kinetics. The GOx was immobilized by glutaraldehyde on substrates of different electrical conductivity: (i) gold covered glass was used as conducting substrate and (ii) plastic poly(methyl methacrylate) was used as non‐conducting substrate. Current vs distance dependencies were registered by SECM at different concentrations of glucose in the absence of redox mediator. The potential of −750 mV vs Ag/AgCl(3 M KCl) was applied to the microelectrode (ME), which was used as a probe in SECM, in order to register oxygen reduction current. Consumption of oxygen by the GOx based layer was evaluated according to principles determined by Michaelis‐Menten kinetics. Apparent Michaelis constants K _{M (app.)} were calculated from the dependencies of current vs glucose concentration. In both these cases the K _{M (app.)} value increased when the distance between ME and enzyme modified surface was increasing from 10 to 30 μm, while the K _{M (app.)} value decreased by increasing the distance from 30 to 60 μm.     

Study on Electrocatalytic Activity of Platinum for Hydrogen Oxidation in Acidic Solution by Scanning Electrochemical Microscopy

The electrocatalytic activity of platinum for hydrogen oxidation in 0.01 M H₂SO₄ + 0.1 MNa₂SO₄ solution has been investigated by scanning electrochemical microscopy (SECM) technique. The cyclic voltammogram (CV), approach curve, area scan imaging and chronoamperometric methods have been used. The results indicate that the imaging capability of the SECM feedback mode can be used more efficiently to visually identify materials' electrocatalytic activity, compared with the approach curve method for identification of the conductive or insulating nature of a surface. The SECM imaging method has demonstrated the effects of Pt substrate potential on the electrocatalytic oxidation of hydrogen under a constant tip potential. It is found that the more positive the Pt substrate potential, the lower the electrocatalytic activity of the Pt. Furthermore, the chronoamperometric results support the variation of the electrocatalytic activity with the Pt substrate potential as well.     

Thin‐Layer Cyclic Voltammetric and Scanning Electrochemical Microscopic Study of Antioxidant Activity of Ascorbic Acid at Liquid/Liquid Interface

An electron transfer reaction between ascorbic acid (H₂A) in an aqueous solution and oxidizing agent in an organic solution immiscible with water has been studied by thin‐layer cyclic voltammetry (TLCV) for charge transfer at the interface between two immiscible electrolyte solutions (ITIES). As an antioxidant, H₂A provide electrons through the aqueous/organic interface to reduce Fc⁺ and the procedure has been proved to be a one electron process again. In this work, the first combination of TLCV and scanning electrochemical microscopy (SECM) was achieved and showed a reasonable agreement between the results from the two different approaches. Otherwise, lower concentration ratios Kr of aqueous to organic reactants was adopted, which is given as evidence to the proposed procedure of Barker.     

Gold Nanoparticle‐Based Redox Signal Enhancement for Sensitive Detection of Human Chorionic Gonadotropin Hormone

A sensitive immunosensor for the detection of pregnancy marker, human chorionic gonadotropin hormone (hCG), was developed using the direct electrical detection of Au nanoparticles. We utilized disposable screen‐printed carbon strips (SPCSs) for the development of our immunosensor, which provided cost‐effective tests with the required antigen sample volume as small as 2 μL. After the recognition reaction between the surface‐immobilized primary antibody and hCG, the captured antigen was sandwiched with a secondary antibody that was labeled with Au nanoparticles. Au nanoparticles were exposed to a preoxidation process at 1.2 V for 40 s, which was subsequently followed with a reduction scan on the same surface using differential pulse voltammetry (DPV). We could observe Au nanoparticle‐labeled antigen‐antibody complexes immobilized on the surface of SPCS using scanning electron microscopy (SEM). Additionally, the number of Au nanoparticles on the immunosensor was determined using SEM images, and showed a linear relationship with the current intensity obtained from the DPV measurements with a detection limit of 36 pg/mL hCG (612 fM, 3.6×10^?4 IU/mL). Our immunosensor system, a combination of the screen‐printing technology with Au nanoparticles provides a promising biosensor for various applications in life sciences.     

Scanning Electrochemical Microscopy (SECM) Based Detection of Oligonucleotide Hybridization and Simultaneous Determination of the Surface Concentration of Immobilized Oligonucleotides on Gold

The direct mode of scanning electrochemical microscopy (SECM) was used for the local deposition of oligonucleotide (ODN) patterns on thin gold films and the generation‐collection (GC) mode was applied for the determining the amount of surface‐accessible oligonucleotides. The local deposition was achieved through the micrometer‐sized formation of a conducting polymer bearing 15^mer single‐stranded oligonucleotide strands. After the interaction of the oligonucleotide with its biotin‐labeled complimentary strand, streptavidin was bound. The molecular assembly was completed by linking biotin‐labeled β‐galactosidase from Escherichia coli to the streptavidin. The activity of the linked β‐galactosidase was mapped with SECM in the GC mode by monitoring the oxidation of p‐aminophenol (PAP) formed in the enzyme‐catalyzed hydrolysis of p‐aminophenyl‐β‐D ‐galactopyranoside. The feedback effect due to recycling of the reaction product at the gold surface was analyzed. It was shown experimentally that this effect becomes insignificant at ultramicroelectrode (UME)‐substrate distances larger than 3 UME radii. The flux of formed PAP allowed the determination the surface density of accessible oligonucleotide strands in the functionalized polymer. It was shown that that thicker pyrrole/ODN–Pyrrole polymer films do not lead to a significantly increased accessible ODN surface concentration.     

AFM‐Correlated CSM‐Coupled Raman/Fluorescence Studies on Selective Interactions of Water Soluble Porphyrins with DNA

The Raman and fluorescence spectroscopic properties of water‐soluble oxo‐titanium(IV) mesotetrakis (1‐methyl pyridium‐4‐yl) porphyrin (O=Ti(TMPyP)⁴⁺) bound with calf thymus DNA and artificial DNAs such as double stranded poly[d(A‐T)₂] and poly[d(G‐C)₂] have been investigated on the single DNA molecule basis by AFM‐correlated confocal scanning microscope (CSM)‐coupled Raman and fluorescence spectroscopic techniques as well as the ensemble‐averaged spectroscopy. The ensemble‐averaged spectroscopic studies imply that the porphyrin interacts with DNA in different groove binding patterns depending on the base pairs. AFM‐images of the different DNAs bound with O=Ti(TMPyP)⁴⁺ were measured, and their morphologies are found to depend on kind of base pairs interacting with O=Ti(TMPyP)⁴⁺. Being correlated with the AFM images, the CSM‐coupled Raman and fluorescence spectral properties of the three different single O=Ti(TMPyP)⁴⁺‐DNA complexes were observed to be highly resolved and sensitive to base pair‐dependent axial ligation of Ti‐O bond as compared to the corresponding ensemble‐averaged spectral properties, which affect the groove binding and its strength of the O=Ti(TMPyP)⁴⁺ with DNA. The axial ligation was found to be accompanied by vibration structural change of the porphyrin ring, leading to keep the shape of double stranded poly[d(A‐T)₂] rigid while poly‐[d(G‐C)₂] and calf thymus DNA flexible after binding with the oxo‐titanyl porphyrin. The base pair dependence of the fluorescence decay times of the DNA‐bound porphyrins was also observed, implying that an excited‐state charge transfer takes place in the G‐C rich major groove in calf thymus DNA. These results suggest that binding of O=Ti(TMPyP)⁴⁺ is more preferential with the G‐C rich major groove than with the A‐T rich minor groove in calf thymus DNA so that the morphology of DNA is changed.     

Investigation of the Effect of Thermal Annealing on Poly(3‐hexylthiophene) Nanofibers by Scanning Probe Microscopy: From Single‐Chain Conformation and Assembly Behavior to the Interfacial Interactions with Graphene Oxide

Poly(3‐hexylthiophene) (P3HT) has been widely used in devices owing to its excellent properties and structural features. However, devices based on pure P3HT have not exhibited high performance. Strategies, such as thermal annealing and surface doping, have been used to improve the electrical properties of P3HT. In this work, different from previous studies, the effect of thermal annealing on P3HT nanofibers are examined, ranging from the single polymer chain conformation to chain packing, and the interfacial interactions with graphene oxide (GO) at nanoscale dimensions, by using scanning tunneling microscopy (STM), atomic force microscopy (AFM) and Kelvin probe force microscopy (KPFM). High‐resolution STM images directly show the conformational changes of single polymer chains after thermal annealing. The morphology of P3HT nanofibers and the surface potential changes of the P3HT nanofibers and GO is further investigated by AFM and KPFM at the nanoscale, which demonstrate that the surface potentials of P3HT decrease, whereas that of GO increases after thermal annealing. All of the results demonstrate the stronger interfacial interactions between P3HT and GO occur after thermal treatments due to the changes in P3HT chain conformation and packing order.     

Separation‐free single‐base extension assay with fluorescence resonance energy transfer for rapid and convenient determination of DNA methylation status at specific cytosine and guanine dinucleotide sites

A separation‐free single‐base extension (SBE) assay utilizing fluorescence resonance energy transfer (FRET) was developed for rapid and convenient interrogation of DNA methylation status at specific cytosine and guanine dinucleotide sites. In this assay, the SBE was performed in a tube using an allele‐specific oligonucleotide primer (i.e., extension primer) labeled with Cy3 as a FRET donor fluorophore at the 5′‐end, a nucleotide terminator (dideoxynucleotide triphosphate) labeled with Cy5 as a FRET acceptor, a PCR amplicon derived from bisulfite‐converted genomic DNA, and a DNA polymerase. A single base‐extended primer (i.e., SBE product) that was 5′‐Cy3‐ and 3′‐Cy5‐tagged was formed by incorporation of the Cy5‐labeled terminator into the 3′‐end of the extension primer, but only if the terminator added was complementary to the target nucleotide. The resulting SBE product brought the Cy3 donor and the Cy5 acceptor into close proximity. Illumination of the Cy3 donor resulted in successful FRET and excitation of the Cy5 acceptor, generating fluorescence emission from the acceptor. The capacity of the developed assay to discriminate as low as 10% methylation from a mixture of methylated and unmethylated DNA was demonstrated at multiple cytosine and guanine dinucleotide sites.     

Interaction of Mitomycin C with DNA Immobilized onto Single‐walled Carbon Nanotube/Polymer Modified Pencil Graphite Electrode

The electrochemical investigation of the interaction between the anticancer drug mitomycin C (MC) and DNA was described using a single‐walled carbon nanotube (SWCNT)/poly(vinylferrocenium) (PVF⁺) modified pencil graphite electrode (PGE). The electrochemical oxidation signals of guanine were monitored before and after the interaction between MC and DNA by using differential pulse voltammetry. The effects of DNA and MC concentration and MC interaction time were examined based on the electrode response. Cyclic voltammetry and electrochemical impedance spectroscopy were used for the characterization of SWCNT/PVF⁺ modified and PVF⁺ modified PGEs. The detection limit corresponded to 625 ng/mL for MC using calf thymus double‐stranded DNA immobilized SWCNT/PVF⁺ modified PGE.     

Nucleic Acid Biosensor for Detection of Human Immunodeficiency Virus Using Aquabis(1,10‐phenanthroline)copper(II) Perchlorate as Electrochemical Indicator

The electrochemical behavior of aquabis(1,10‐phenanthroline)copper(II) perchlorate [Cu(H₂O)(phen)₂]·2ClO₄, where phen=1,10‐phenanthroline, on binding to DNA at a glassy carbon electrode (GCE) and in solution, was described. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) results showed that [Cu(H₂O)(phen)₂]²⁺ had excellent electrochemical activity on the GCE with a couple of quasi‐reversible redox peaks. The interaction mode between [Cu(H₂O)(phen)₂]²⁺ and double‐strand DNA (dsDNA) was identified to be intercalative binding. An electrochemical DNA biosensor was developed with covalent immobilization of human immunodeficiency virus (HIV) probe for single‐strand DNA (ssDNA) on the modified GCE. Numerous factors affecting the probe immobilization, target hybridization, and indicator binding reactions were optimized to maximize the sensitivity and speed of the assay. With this approach, a sequence of the HIV could be quantified over the range from 7.8×10^?9 to 3.1×10^?7 mol·L^?1 with a linear correlation of γ=0.9987 and a detection limit of 1.3×10^?9 mol·L^?1.     

Acid dissolution of copper oxides as a method for the activation of Cu(0) wire catalyst for SET‐LRP

Here we reported the acid dissolution of copper oxides as a methodology for the activation of Cu(0) wire used as catalyst in single‐electron transfer living radical polymerization (SET‐LRP). In this method, the oxide layer on the surface of commercial Cu(0) wire was removed by dissolution in a concentrated acid such as nitric acid, glacial acetic acid and hydrochloric acid. SET‐LRP of methyl acrylate catalyzed with Cu(0) wire activated with acids showed comparable k value to that of the nonactivated Cu(0) wire‐catalyzed counterpart. However, the polymerizations catalyzed with activated Cu(0) wire proceeded with no initial induction period, predictable molecular weight evolution with conversion, and narrow molecular weight distribution. Regardless of the activation method, the chain end functionality of α,ω‐di(bromo) poly(methyl acrylate) (PMA) prepared from SET‐LRP initiated with a bifunctional initiator is extremely high, maintaining a 100% chain end functionality at ～90% monomer conversion. The degree of bimolecular termination increased as the polymerization exceeds 92% conversion. However, for binfunctional initiators this small amount of bimolecular termination at high conversion maintains a perfectly bifunctional polymer. Structural analysis by MALDI‐TOF upon thioetherification of α,ω‐di(bromo) PMA with thiophenol and 4‐fluorothiophenol confirmed the high fidelity of bromide chain ends. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Non‐enzymatic Electrochemical Sensor for the Simultaneous Determination of Xanthine,its Methyl Derivatives Theophylline and Caffeine as well as its Metabolite Uric Acid

Xanthine and its methyl derivatives, theophylline and caffeine are purines which find important roles in biological systems. The simultaneous voltammetric behaviour of these purines has been studied on a glassy carbon electrode modified with an electropolymerised film of para amino benzene sulfonic acid. Well defined and well separated peaks were obtained for the oxidation of xanthine, theophylline and caffeine on the polymer modified electrode in the square wave mode. The experimental requirements to obtain the best results for individual as well as simultaneous determination were optimised. The signal for the electro‐oxidation was found to be free of interferences from each other in the range 0.9 – 100 μM in the case of xanthine and from 10–100 μM in the case of theophylline and caffeine with detection limits 0.35 μM, 7.02 μM and 11.95 μM respectively. The simultaneous determination of uric acid, the final metabolic product of xanthine oxidation in biological systems could also be accomplished along with xanthine, theophylline and caffeine atphysiological pH. The mechanistic aspects of the electro‐oxidation on the polymer modified electrode was also studied using linear sweep voltammetry. Chronoamperometry was employed to determine the diffusion coefficient of these xanthines. The developed sensor has been successfully demonstrated to be suitable for the determination of these compounds in real samples without much pre‐treatment.     

Building‐Block Approach for the Straightforward Incorporation of a New FRET (Fluorescence‐Resonance‐Energy Transfer) System into Synthetic DNA

The synthesis of the two new phosphoramidites 5 and 8 bearing a carbostyril (=quinolin‐2(1H)‐one) chromophore used as donor entity in our recently developed new FRET (fluorescence‐resonance‐energy transfer) system is described (Schemes 1 and 2) The high stability of the chromophore to basic conditions enables the incorporation of the phosphoramidites directly into DNA during solid‐phase synthesis (Schemes 3 and 4). Since this is also possible for the (bathophenanthroline)ruthenium(II) complex used as acceptor (Scheme 4, Steps d and e), the whole labelling procedure to insert the FRET system into synthetic DNA is straightforward and represents a major improvement to our previous strategy.     

A Selective Voltammetric Method for Uric Acid Detection at a Glassy Carbon Electrode Modified with Electrodeposited Film Containing DNA and Pt‐Fe(III) Nanocomposites

A novel biosensor by electrochemical codeposited Pt‐Fe(III) nanocomposites and DNA film was constructed and applied to the detection of uric acid (UA) in the presence of high concentration of ascorbic acid (AA). Based on its strong catalytic activity toward the oxidation of UA and AA, the modified electrode resolved the overlapping voltammetric response of UA and AA into two well‐defined peaks with a large anodic peak difference (ΔE_pa) of about 380mV. The catalytic peak current obtained from differential pulse voltammetry (DPV) was linearly dependent on the UA concentration from 3.8×10^?6 to 1.6×10^?4 M (r=0.9967) with coexistence of 5.0×10^?4 M AA. The detection limit was 1.8×10^?6 M (S/N=3) and the presence of 20 times higher concentration of AA did not interfere with the determination. The modified electrode shows good sensitivity, selectivity and stability.     

Development of a Novel Electrochemical Biosensor for Detection and Discrimination of DNA Sequence and Single Base Mutation in dsDNA Samples Based on PNA‐dsDNA Hybridization – a new Platform Technology

In spite of the extensive attention paid on the development of various DNA detection strategies, very few studies have been reported regarding direct detection of DNA sequence and mutation in dsDNA. Here, we describe the feasibility of detection and discrimination of target DNA sequences and single base mutations (SBM) directly in double‐stranded oligonucleotides and PCR products without the need for denaturation of the target dsDNA samples. This goal was achieved by employing a peptide nucleic acid (PNA) chain, self‐assembled on the gold electrode as a probe, which binds to dsDNA and forms PNA‐dsDNA hybrid.     

Redox Materials by the Covalent Entrapment of Redox‐Active Dirhodium(II,II) Species in a Siloxane Network

Summary: Hydrolysis and polycondensation of the coupling agent (aminopropyl)triethoxysilane (APS), axially coordinated to the redox‐active complex [Rh₂(form)₂(CH₃COO)₂(APS)₂], lead to the insertion of redox‐active inorganic microdomains into a siloxane network; the new polymers undergo cyclic redox reactions indicating that dirhodium(II ,II ) centres retain their redox activity even when incorporated into siloxane networks.

The redox‐active complex [Rh₂(form)₂(CH₃COO)₂(APS)₂] (form = N,N′‐di‐p‐tolylformamidinate) incorporated into a siloxane network here.     

Synthesis of dual‐functional poly(6‐azidohexylmethacrylate) brushes by a RAFT agent carrying carboxylic acid end groups

Novel types of dual‐functional surface‐attached polymer brushes were developed by interface‐mediated reversible addition‐fragmentation chain transfer (RAFT) polymerization of 6‐azidohexylmethacrylate using the surface‐immobilized RAFT agent and the free initiator. The interface‐mediated RAFT polymerization produced silicon substrate coated with dual‐functional (azido groups from monomer and carboxylic acid groups from RAFT agent) poly(6‐azidohexylmethacrylate) [poly (AHMA)] with a grafting density as high as 0.59 chains/nm². Dual‐functional polymer brushes can represent an attractive chemical platform to deliberately introduce other molecular units at specific sites. The azido groups of the poly(AHMA) brushes can be modified with alkyl groups via click reaction, known for their DNA hybridization, while the carboxylic acid end groups can be reacted with amine groups via amide reaction, known for their antifouling properties. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1696–1706