Electrochemical Characterization and Voltammetric Determination of Methylisothiazolinone on a Boron-Doped Diamond Electrode

The electrochemical properties of methylisothiazolinone (MIT), the most widely used preservative, were investigated by cyclic (CV) and differential pulse voltammetry (DPV) to develop a new method for its determination. To our knowledge, this is the first demonstration of a voltammetric procedure for the determination of MIT on a boron-doped diamond electrode (BDDE) in a citrate–phosphate buffer (C-PB) environment. The anodic oxidation process of methylisothiazolinone, which is the basis of this method, proved to be diffusion-controlled and proceeded with an irreversible two-electron exchange. The radical cations, as unstable primary products, were converted in subsequent chemical reactions to sulfoxides and sulfones, and finally to more stable final products. Performed determinations were based on the DPV technique. A linear calibration curve was obtained in the concentration range from 0.7 to 18.7 mg L⁻¹, with a correlation coefficient of 0.9999. The proposed procedure was accurate and precise, allowing the detection of MIT at a concentration level of 0.24 mg L⁻¹. It successfully demonstrated its suitability for the determination of methylisothiazolinone in household products without the need for any separation steps. The proposed method can serve as an alternative to the prevailing chromatographic determinations of MIT in real samples.     

Direct and Simultaneous Determination of Phenol, Hydroquinone and Nitrophenol at Boron-Doped Diamond Film Electrode

The electrochemical characteristics of multi-component phenolic pollutants, such as phenol （Ph）, hydroquinone （HQ） and 4-nitrophenol （4-NP）, were investigated on boron-doped diamond （BDD） film electrode by differential pulse voltammetry （DPV） technique. A simple and feasible platform was accordingly established for the direct and simultaneous determination of these three phenolic pollutants. Results showed that, Ph, HQ and 4-NP gave obvious oxidation peaks on BDD electrode at the potential of 1.24, 0.76 and 1.52 V, respectively. Each of them displayed good linear relationship between their oxidation peak currents and their corresponding concentrations in a rather wide range coexisting with one or two of the other phenolic pollutants. The detection limits of Ph, HQ and 4-NP were estimated to be as low as 1.82×10^-6, 1.67×10^-6 and 1.44×10^-6 mol·L^-1, respectively. Therefore, a promising direct and simultaneous electrochemical determination method of multi-component phenolic pollutants in wastewater samples was constructed successfully on BDD electrode with advantages being rapid, simple, convenient, sensitive, in situ and inexpensive.     

Differential Pulse Anodic Stripping Voltammetric Determination of Lead with Heparin Modified Electrode

Introduction Overall exposure to lead is of public health concern because of several hazardous effects that may occur to human beings. Lead poisoning may provoke irritability, anorexia, malaise and headache. Intoxication progress may lead to attacks of abdominal pain until coma and death.1 The determination of trace lead in variety of en-vironmental samples is of great importance since lead is recognized as a cumulative poison to animals and hu-mans. There is a constant demand for improved an…     

The Performance of Boron‐Doped Diamond Electrode for the Determination of Ramipril and its Association with Hydrochlorothiazide

The voltammetric behavior of ramipril (RMP), an angiotensin‐converting enzyme inhibitor, was investigated for the first time in the literature on a boron‐doped diamond electrode (BDDE) using cyclic (CV) and square‐wave voltammetry (SWV). Its behavior was also considered in the presence of a thiazide diuretic, hydrochlorothiazide (HCTZ), for the simultaneous determination. The performance of BDDE and glassy carbon electrode (GCE) was compared, since RMP provides a high oxidation potential. It was observed that the anodic peak potentials for HCTZ and RMP at the BDDE were 1.23 and 1.67 V (vs . Ag/AgCl (3.0 mol L^‐1 KCl)) by CV in BR buffer solution (pH 2.0), respectively. The influence of supporting electrolyte, pH and scan rate in the current response of these both drugs was examined to select optimum experimental conditions. By this way, the determination of RMP and its association with HCTZ using SWV and a BDDE was successfully applied in real samples (single and combined dosage forms), with results in close agreement at 95% confidence level with those obtained using high‐performance liquid chromatography.     

Voltammetric Determination of Hemoglobin Using a Pencil Lead Electrode

In this paper the electrochemical behavior of hemoglobin (Hb) immobilized on a pencil lead electrode (PLE) was investigated. Immobilization of Hb on the pencil lead electrode was performed by nonelectrochemical and electrochemical methods. In phosphate buffer solution with pH 7.0 Hb showed a pair of well‐defined and nearly reversible redox waves (the anodic and cathodic peak potentials are located at ?0.18 V and ?0.22 V, respectively). The dependence of the anodic peak potential (E_pa) on the pH of the buffer solution indicated that the conversion of Hb? Fe(III)/Hb? Fe(II) is a one‐electron‐transfer reaction process coupled with one‐proton‐transfer. In addition the effect of scan rate on peak currents and peak separation potential was investigated and electrochemical parameters such as α and k_s were calculated. In the second part of this work, the ability of the electrode for determination of Hb concentration was investigated. The results showed a linear dynamic range from 0.15 to 2 µM and a detection limit of 0.11 µM. The relative standard deviation is 4.1 % for 4 successive determinations of a 1 µM Hb solution.     

Voltammetric Behavior of Nitrofurazone at Highly Boron Doped Diamond Electrode

The electrochemical behavior of nitrofurazone (NFZ) at a highly boron doped diamond (BDD) electrode was studied in Britton‐Robinson (BR) buffer using cyclic voltammetry. NFZ was directly reduced to the amine derivative (RNH₂) in the pH range of 2.0 to 4.0 in a process involving six (6.0±0.4) electrons and six protons. In the range of pH 7.0 to 12 and, predominantly aqueous medium, the reduction step split into its two components: the reduction of NFZ to the radical anion (RNO₂^.?) and reduction of RNO₂^.? to hydroxylamine derivative (RNHOH) in processes involving one and three (3.1±0.1) electrons, respectively. On the anodic scan of the voltammograms and at pH 8.0, the oxidation of the hydroxylamine to the nitroso derivative (RNO), was observed in a process involving 2 (1.7±0.2) electrons and 2 protons. In addition and unreported in the literature on any electrode material, was the detection of a new oxidation peak at pH>8.0, which was observed regardless of whether NFZ had been previously reduced or not. The calculation of n, number of electrons, involved in each electrochemical step was satisfactorily accomplished using the Randles‐?evcik equation.     

Simultaneous Differential Pulse Voltammetric Determination of Ascorbic Acid and Caffeine in Pharmaceutical Formulations Using a Boron‐Doped Diamond Electrode

A cathodically pretreated boron‐doped diamond electrode was used for the simultaneous anodic determination of ascorbic acid (AA) and caffeine (CAF) by differential pulse voltammetry. Linear calibration curves (r=0.999) were obtained from 1.9×10^?5 to 2.1×10^?4 mol L^?1 for AA and from 9.7×10^?6 to 1.1×10^?4 mol L^?1 for CAF, with detection limits of 19 μmol L^?1 and 7.0 μmol L^?1, respectively. This method was successfully applied for the determination of AA and CAF in pharmaceutical formulations, with results equal to those obtained using a HPLC reference method.     

聚l-异白氨酸修饰电极的制备及对多巴胺的测定

聚合物修饰电极;l-异白氨酸;多巴胺;循环伏安法     

Voltammetric Determination of 3‐Nitrofluoranthene and 3‐Aminofluoranthene at Boron Doped Diamond Thin‐Film Electrode

The voltammetric behavior of 3‐nitrofluoranthene and 3‐aminofluoranthene was investigated in mixed methanol‐water solutions by differential pulse voltammetry (DPV) at boron doped diamond thin‐film electrode (BDDE). Optimum conditions have been found for determination of 3‐nitrofluoranthene in the concentration range of 2×10^?8–1×10^?6 mol L^?1, and for determination 3‐aminofluorathnene in the concentration range of 2×10^?7–1×10^?5 mol L^?1, respectively. Limits of determination were 3×10^?8 mol L^?1 (3‐nitrofluoranthene) and 2×10^?7 mol L^?1 (3‐aminofluoranthene).     

Adsorptive Stripping Voltammetric Determination of Trace Level Ricin in Castor Seeds Using a Boron‐doped Diamond Electrode

Ricin, (Ricinus communis agglutinin, RCA) is one of the most poisonous of naturally occurring substances and has great potential for bioterrorism because no antidote exists. Fast detection at low concentrations is a challenge, and vital to the development of proper countermeasures. In this study, a square wave adsorptive stripping voltammetric (SWAdSV) method for determining RCA using a cathodically polarized boron‐doped diamond (BDD) electrode is presented. An irreversible electrochemical RCA oxidation peak was identified on the BDD electrode by different voltammetric techniques using both direct and adsorptive stripping modes. An adsorption‐controlled (slope log Ip vs log v of 0.80) pH‐dependent process was observed. For values of 1.0≤pH≤9.0, the numbers of protons and electrons associated with the oxidation reaction were estimated (ca. 1.0) by differential pulse voltammetry. The RCA oxidation step may correspond to the oxidation of tryptophan amino acid residues, and occurs in a complex mechanism. The excellent analytical performance of the cathodically polarized BDD electrode in combination with the stripping mode ramp was verified with RCA by using a short deposition time in an open circuit potential (120 s). Under optimized analysis conditions, a linear response in the range of (3.3–94.0)×10⁻⁹ mol L⁻¹ (r²=0.9944) and a limit of detection of 6.2×10⁻¹⁰ mol L⁻¹ were estimated. This LOD is lower than several methods found in the literature. For example, it is 168 times lower than that obtained by using square wave voltammetric with a glassy carbon electrode. Moreover, an even lower LOD might be achieved by using the SWAdSV method with a higher pre‐concentration time. In addition, trace levels of RCA were successfully determined in different castor seed cultivars with an overall average recovery from 99.2±1.6 % for the three different RCA‐A concentration levels. The high accuracy of the analytical data highlights the use of the proposed method for determining RCA in other samples.     

聚L-赖氨酸修饰电极循环伏安法测定药剂中的多巴胺

用循环伏安法制备了聚L-赖氨酸修饰玻碳电极,研究多巴胺在聚L-赖氨酸修饰电极上的电化学行为,建立了循环伏安法测定多巴胺的新方法。实验结果表明,在pH7.0的磷酸盐缓冲溶液中,扫描速率为150mV/s,循环扫描电位在-0.3~0.6V时,多巴胺在聚L-赖氨酸修饰玻碳电极上出现一对灵敏的氧化还原峰,峰电位分别为Epa=0.175V,Epc=0.146V(相对饱和甘汞电极);测定多巴胺的线性范围为1.0×10-3~1.0×10-5mol/L和1.0×10-5~8.0×10-9mol/L,方法检出限1.0×10-9mol/L。用于药剂中多巴胺的测定。     

Electroanalytical Determination of Carbaryl in Natural Waters on Boron Doped Diamond Electrode

The anodic voltammetric behavior of carbaryl on a boron‐doped diamond electrode in aqueous solution is reported. The results, obtained by square‐wave voltammetry at 0.1 mol L^?1 Na₂SO₄ and pH 6.0, allow the development of a method to determine carbaryl, without any previous step of extraction, clean‐up, preconcentration or derivatization, in the range 2.5–30.0×10^?6 mol L^?1, with a detection limit of 8.2±0.2 μg L^?1 in pure water. The analytical sensitivity of this electrochemical method diminished slightly, from 3.07 mA mmol^?1 L to 2.90 mA mmol^?1L, when the electrolyte was prepared with water samples collected from two polluted points in an urban creek. In these conditions, the recovery efficiencies obtained were around 104%. The effect of other pesticides (fenthion and 4‐nitrophenol) was evaluated and found to exert a negligible influence on carbaryl determination. The square‐wave voltammetric data obtained for carbaryl were typical of an irreversible electrode process with mass transport control. The combination of square‐wave voltammetry and diamond electrodes is an interesting and desirable alternative for analytical determinations.     

Simultaneous Differential Pulse Voltammetric Determination of Sulfamethoxazole and Trimethoprim on a Boron‐Doped Diamond Electrode

The performance of hydrogen‐ (HT) and oxygen‐terminated (OT) boron‐doped diamond (BDD) electrodes (electrochemically pretreated) on the simultaneous differential pulse voltammetric determination of sulfamethoxazole and trimethoprim in pharmaceutical products is presented. Under the optimum analytical experimental conditions, the HT‐BDD electrode presented two well‐defined oxidation peaks at 920 and 1100 mV vs. Ag/AgCl for sulfamethoxazole and trimethoprim, respectively. On the other hand, when the OT‐BDD electrode was used, the sulfamethoxazole oxidation current peak was decreased twenty fold. The calculated LOD values for sulfamethoxazole and trimethoprim using the HT‐BDD electrode were 3.65 μg L^?1 and 3.92 μg L^?1, respectively. The results obtained in the simultaneous determination of sulfamethoxazole and trimethoprim in three different commercial formulations were similar to those obtained using a standard HPLC method at 95% confidence level.     

多巴胺在电沉积石墨烯修饰碳分子线电极上的电化学测定

以分子线二苯乙炔为修饰剂和粘合剂制备了一种新型的碳糊电极-碳分子线电极(CMWE),并以其为基底电极采用电化学还原法将石墨烯(GR)沉积到CMWE表面得到电沉积石墨烯修饰碳分子线电极(GR/CMWE)。考察了多巴胺(DA)在该修饰电极上的电化学行为。实验结果显示DA在GR/CMWE上出现了1对峰形良好的氧化还原峰,与裸电极相比,该氧化还原峰的电流增大,峰电位差减小,表明修饰电极对DA的电化学反应有催化作用。在最佳实验条件下峰电流与DA浓度在8.0×10-7~2.0×10-3mol/L范围内呈良好的线性关系,检出限(3σ)为2.55×10-7mol/L。将该电极用于多巴胺注射液样品的检测,结果满意。     

Electroanalytical Determination of Morpholine as a Corrosion Inhibitor at a Cathodically Pretreated Boron-Doped Diamond Electrode

An electroanalytical method for the determination of morpholine, a corrosion inhibitor, was developed at a cathodically pretreated boron-doped diamond electrode (BDDE). The voltammetric response of morpholine at the BDDE in 0.1?mol L^?1 KCl (pH 10) shows an irreversible oxidation process at approximately 1.3?V vs. Ag/AgCl in 3.0?mol L^?1 KCl. Using cyclic voltammetry, the number of electrons involved in the morpholine electroxidation mechanism was found to be 1. The application of chronoamperometry showed that the apparent diffusion coefficient (D₀) was 2.99?×?10^?6 cm² s^?1. Using square wave voltammetry under the optimized conditions (frequency of 30.0?Hz, pulse amplitude of 100?mV and step potential of 20?mV at pH 10.0), the developed method provided limits of detection and quantification of 2.1 and 6.9?mg L^?1, respectively, with a linear range from 5.0 to 100.0?mg L^?1 (r?=?0.991). Intraday (n?=?10) and interday (two consecutive day) precision values assessed as the relative standard deviation for solutions containing 30.0, 60.0, and 90.0?mg L^?1 of morpholine were from 0.41 to 5.86% and 0.92 to 3.19%, respectively. The feasibility of the method for the interference-free determination of morpholine was verified by the analysis of synthetic boiler water samples containing CaCO₃, Na₂SO₃, Na₃PO_4, FeCl₃, and humic acid as organic matter. In addition, hydrazine was added as a possible interfering compound because of its widespread use in corrosion inhibition. Recovery values from 90.9 to 109.4% were obtained in the synthetic boiler water, thereby attesting to the accuracy of the method.     

Pencil Lead Electrode Modified with Hemoglobin Film as a Novel Biosensor for Nitrite Determination

In the present paper, the electrochemical reduction of nitrite at a hemoglobin modified pencil lead electrode (Hb/PLE) is described. The electrochemical properties of nitrite were studied by cyclic voltammetry and chronoamperometry. Results showed that the hemoglobin film has an excellent electrochemical activity towards the reduction of nitrite. By using voltammetric and chronoamperometric methods, α, n_α and n were calculated. Then the ability of the electrode for nitrite determination was investigated using differential pulse voltammetry. The electrocatalytic reduction peak currents were found to be linear with the nitrite concentration in the range from 10 to 220 µM with a detection limit of 5 µM. The relative standard deviation is 2 % for 3 successive determinations of a 100 µM nitrite solution. This modified electrode was successfully used for the detection of low amounts of NO₂^? in spinach sample and a spiked sample of tap water.     

聚对硝基苯偶氮间苯二酚修饰电极伏安法测定多巴胺

采用循环伏安法研究了多巴胺(DA)在聚对硝基苯偶氮间苯二酚(p-nitrobenzenazo resorcinol,简称NBAR)膜修饰电极上的电化学行为,用差示脉冲伏安法对多巴胺的含量进行测定.结果表明,聚NBAR膜修饰电极对DA有明显的电催化作用.在pH4.0的磷酸盐缓冲液中,氧化峰电流与DA浓度在5.0×10-6~8.0×10-4mol/L范围内呈良好的线性关系,检测限为6.0×10-7mol/L.修饰电极可有效消除针剂中其它组分对DA测定的干扰,已用于实际样品DA含量的测定,结果令人满意.     

A New Sensor for Simultaneous Determination of Tyrosine and Dopamine Using Iron(III) Doped Zeolite Modified Carbon Paste Electrode

A new chemically modified electrode is constructed based on iron(III) doped zeolite modified carbon paste electrode (Fe³⁺Y/ZMCPE). The new sensor could be used for the simultaneous determination of the biologically important compounds dopamine (DA) and tyrosine (Tyr). The measurements are carried out using differential pulse voltammetric (DPV) method. The prepared modified electrode shows voltammetric responses of high sensitivity, selectivity and stability for DA and Tyr under optimal conditions, which makes it a suitable sensor for simultaneous trace detection of DA and Tyr in solution. Application of the DPV method demonstrates that in the Briton Robinson buffer solutions (pH=5) containing 50 µmol/L Tyr, there is a linear relationship between the oxidation peaks and the concentrations of DA over the range of 0.1–200 µmol/L, with a detection limit of 0.05 µmol/L (S/N=3). For Tyr a linear correlation between oxidation peak current and concentration of Tyr over the range of 0.5–200 µmol/L (containing 50 µmol/L DA), with a detection limit of 0.08 µmol/L is obtained. The analytical performances of this sensor are evaluated for the detection of DA and Tyr in human serum and a medicine.     

银掺杂聚L-甲硫氨酸修饰电极同时测定对苯二酚和邻苯二酚

用循环伏安法制备了银掺杂聚L-甲硫氨酸修饰玻碳电极,研究了对苯二酚和邻苯二酚在该修饰电极上的电化学行为,建立了同时测定对苯二酚和邻苯二酚的新方法.研究发现,在pH=5.0的磷酸盐缓冲溶液中,扫速为100 mV/s时,对苯二酚和邻苯二酚在银掺杂聚L-甲硫氨酸修饰玻碳电极上均出现1对氧化还原峰,峰电位分别为:Epa=0.228 V、Epc =0.162 V和Epa=0.347 V、Epc =0.287 V,二者的氧化峰电位差达119 mV,还原峰差达125 mV.在最佳的条件下,用差分脉冲伏安法同时测定邻苯二酚和对苯二酚的线性范围为3.00 ×10-6～1.00 ×10-4mol/L,检出限为8.0×10-7 mol/L(对苯二酚)和5.0×10-7 mol/L(邻苯二酚).此法用于废水样中对苯二酚和邻苯二酚的测定,获得满意结果.     

聚对氨基苯磺酸修饰电极差分脉冲伏安法测定对乙酰氨基酚

在由pH 7.0的磷酸盐缓冲溶液和2.0×10~(-3)mol·L~(-1)对氨基苯磺酸组成的支持电解质中,以100mV·s~(-1)扫描速率在玻碳电极上先后在电位-1.5～2.5V范围内循环扫描10周、在电位-1.5～1.5V范围内循环扫描15min,制得聚对氨基苯磺酸修饰的玻碳电极。循环伏安法研究发现:对乙酰氨基酚在该修饰电极上出现了一对氧化还原峰,两峰的电位差为30mV;差分脉冲伏安法研究发现:在pH5.9的磷酸盐缓冲溶液中,对乙酰氨基酚在0.295V处出现一良好的氧化峰。且乙酰氨基酚的浓度在2.0×10~(-7)～1.0×10~(-5)mol·L~(-1)范围内与峰电流呈线性关系,检出限(3S/N)为9.0×10~(-8)mol·L~(-1)。据此提出了差分脉冲伏安法测定药片中对乙酰氨基酚的含量,3个样品的测定结果与标示值相符,测得平均回收率为98.6%,相对标准偏差(n=6)均小于3.5%。