A Novel Electrochemical Sensor for Detection of Molinate Using ZnO Nanoparticles Loaded Carbon Electrode

In this work, electrochemical detection of molinate herbicide was studied by developing a novel sensor based on carbon paste incorporated with zinc oxide (ZnO) nanoparticles using cyclic (CV) and square wave voltammetric (SWV) techniques. Molinate exhibited one well resolved peak at pH of 3.0 phosphate buffer solution (PBS), which was irreversible. The lowest possible detection limit of 1.0×10^?8 M was achieved in the concentration range of 0.002 μM to 0.25 μM. The modifying ability of ZnO nanoparticles was responsible for such a low level sensing in water and soil samples.     

Electrocatalytic Oxidation and Determination of Dopamine in the Presence of Ascorbic Acid and Uric Acid at a Poly (4‐(2‐Pyridylazo)‐Resorcinol) Modified Glassy Carbon Electrode

A sensitive and selective electrochemical method for the determination of dopamine (DA) was developed using a 4‐(2‐Pyridylazo)‐Resorcinol (PAR) polymer film modified glassy carbon electrode (GCE). The PAR polymer film modified electrode shows excellent electrocatalytic activity toward the oxidation of DA in a phosphate buffer solution (PBS) (pH 4.0). The linear range of 5.0×10^?6–3.0×10^?5 M and detection limit of 2.0×10^?7 M were observed. Simultaneous detection of AA, DA and UA has also been demonstrated on the modified electrode. This work provides a simple and easy approach to selective detection of DA in the presence of AA and UA.     

Nanomolar Determination of Methyldopa in the Presence of Large Amounts of Hydrochlorothiazide Using a Carbon Paste Electrode Modified with Graphene Oxide Nanosheets and 3‐(4′‐Amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic Acid

A novel electrochemical sensor for sensitive detection of methyldopa at physiological pH was developed by the bulk modification of carbon paste electrode (CPE) with graphene oxide nanosheets and 3‐(4′‐amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic acid (3,′AA). Applying square wave voltammetry (SWV), in phosphate buffer solution (PBS) of pH 7.0, the oxidation current increased linearly with two concentration intervals of methyldopa, one is 1.0×10^?8–1.0×10^?6 M and the other is 1.0×10^?6–4.5×10^?5 M. The detection limit (3σ) obtained by SWV was 9.0 nM. The modified electrode was successfully applied for simultaneous determination of methyldopa and hydrochlorothiazide. Finally, the proposed method was applied to the determination of methyldopa and hydrochlorothiazide in some real samples.     

Yeast-based carbon paste bioelectrode for ethanol

An amperometric bioelectrode for primary alcohols based on the incorporation of yeasts into the carbon paste matrix is reported. The response is based on the activity of alcohol dehydrogenase in yeasts. The intimate contact between the biocatalytic and sensing sites results in short response times. The addition of a redox-mediating hexacyanoferrate (III) ion greatly facilitates the detection of the enzymatically produced NADH. The effects of operating potential, carbon paste composition, concentration of coenzyme or redox mediator and other parameters are explored for optimum analytical performance. The dynamic properties of this electrode are exploited for detection in flow-injection systems, with a detection limit of 2 × 10^?6 M (9 ng) of ethanol. The relative standard deviation for repetitive injections of a 1× 10^?3 M ethanol solution over a 100-min period is 2.8%. Applicability to alcoholic beverages is illustrated. The trend in sensitivity toward different alcohols is in agreement with the known biospecificity of yeast alcohol dehydrogenase.     

Methylated Azopyridine as a New Electron Transfer Mediator for the Electrocatalytic Oxidation of NADH

Carbon ionic liquid electrode (CILE) has been modified with a new synthesized mediator i.e. N,N′‐dimethyl‐4,4′‐azopyridinium hexafluorophosphate (MAZPHP) via sol process and the electron transfer mediating characteristics of this mediator has been evaluated. 4,4′‐Azopyridine (AZP) did not show any electrocatalytic activity toward the selected probe, NADH, while its synthesized methylated derivative, MAZPHP, is a very efficient mediator for the electrocatalytic NADH oxidation. Cyclic voltammetry of MAZPHP/Sol/CILE exhibited a pair of reversible peaks corresponding to incorporated mediator with a formal potential of about 221 mV vs. Ag/AgCl. MAZPHP/Sol/CILE is free from fouling effects by the oxidation products of NADH which generally give hindrance to amperometric detection of NADH. Using amperometric technique, NADH can be determined in the range of 1.0×10^?5 M to 1.4×10^?3 M with a detection limit of 2.0×10^?6 M.     

Study of Electrooxidation Behavior of Nitrite on Gold Nanoparticles/Graphitizing Carbon Felt Electrode and Its Analytical Application

In this work, a gold nanoparticles/graphitizing carbon felt electrode (AuNPs/GCFE) was fabricated and a disposable sensor was thus fabricated to detect nitrite quickly and conveniently. The kinetic parameters of the electrode were studied in phosphate buffer solution (PBS). Under the optimal conditions, by using cyclic voltammetry, the oxidation peak current was linear with the concentration of nitrite in the range from 1.00 × 10^?6 M to 3.35 × 10^?3 M, with a detection limit of 9.50 × 10^?7 M (3S/k). The influence of various anions on nitrite detection was studied, and the results showed that the fabricated sensor had good specificity toward nitrite.     

Zinc Oxide Modified Au Electrode as Sensor for an Efficient Detection of Hydrazine

ZnO nanoparticles (ZnO NPs) prepared by microwave heating technique are used to modify a gold electrode (ZnO/Au) for the hydrazine detection study. The synthesized product is well characterized by various techniques. Detailed electrochemical investigation of the oxidation of hydrazine on the ZnO/Au electrode in 0.02 M phosphate buffer solution (PBS) of pH 7.4 was carried out. A very low detection limit of 66 nM (S/N=4) and a wide linearity in current for a concentration range from 66.0×10^?3 to 415 µM was achieved by amperometry. The electrode was found to be stable for over a month when preserved in PBS.     

Accelerating the electron transfer of choline oxidase using ionic-liquid/NH2-MWCNTs nano-composite

A nano-composite consisting of amine functionalized multi-walled carbon nanotubes and a room temperature ionic liquid (1-butyl-3-methylimidazolium tetrafluoroborate) was prepared and used for modification of glassy carbon electrode. By immobilizing choline oxidase (ChOx) on the modified electrode, the enzyme direct electron transfer has been achieved. The modified electrode exhibited a pair of well-defined cyclic voltammetric peaks at a formal potential of ?0.395?V versus Ag/AgCl in 0.2?M phosphate buffer solution at pH 7.0. This peak was characteristic of ChOx-FAD/FADH₂ redox couple. The electrochemical parameters such as charge transfer coefficient (??) and apparent heterogeneous electron transfer rate constant (k _s) were estimated to be 0.36 and 2.74?s^?1, respectively. When the enzyme electrode was examined for the detection of choline, a relatively high sensitivity (2.59???A?mM^?1) was obtained. Under the optimized experimental conditions, choline was detected in the concentration range from 6.9?×?10^?3 to 6.7?×?10^?1?mM with a detection limit of 2.7???M. The peak currents of ChOx were reasonably stable and retained 90% of its initial current after a period of 2?months.     

Electrocatalytic Oxidation and Determination of Norepinephrine at Poly(Cresol Red) Modified Glassy Carbon Electrode

A glassy carbon electrode (GCE) was modified with electropolymerized films of cresol red in pH 5.6 phosphate buffer solution (PBS) by cyclic voltammetry (CV). The modified electrode shows an excellent electrocatalytic effect on the oxidation of norepinephrine (NE). The peak current increases linearly with the concentration of NE in the range of 3×10^?6–3×10^?5 M by the differential pulse voltammetry. The detection limit was 2×10^?7 M. The modified electrode can also separate the electrochemical responses of norepinephrine and ascorbic acid (AA). The separation between the anodic peak potentials of NE and AA was 190 mV by the cyclic voltammetry. And the responses to NE and AA at the modified electrode were relatively independent.     

Flow Injection Analysis of Maleic Hydrazide Using an Electrochemical Sensor Based on Palladium‐Dispersed Carbon Paste Electrode

A new analytical methodology for the electrochemical detection of the herbicide maleic hydrazide (3,6‐dihydroxypyridazine) by flow injection analysis is presented. This method is supported by the novel application of a palladium‐dispersed carbon paste electrode as an amperometric sensor for this herbicide. Maleic hydrazide shows anodic electrochemical activity on carbon‐based electrodes (glassy carbon or carbon paste electrodes) in all the pH range. This electrochemical activity is enhanced using metal‐dispersed carbon paste electrodes, especially at Pd‐dispersed CPE which displays good oxidation signals at 690 mV (0.050 M phosphate buffer pH 7.0), 140 mV lower than at unmodified electrodes. Under the optimized conditions, the electroanalytical performance of Pd‐dispersed CPE in flow injection analysis was excellent, with good reproducibility (RSD 3.3%) and a wide linear range (1.9×10^?7 to 1.0×10^?4 mol L^?1). A detection limit of 1.4×10^?8 mol L^?1 (0.14 ng maleic hydrazide) was obtained for a sample loop of 100 μL at a fixed potential of 700 mV in 0.050 M phosphate buffer solution at pH 7.0 and a flow rate of 2.0 mL min^?1. The proposed method was applied for the maleic hydrazide detection in natural drinking water samples.     

A Novel NH2/ITO Ion Implantation Electrode: Preparation,Characterization, and Application in Bioelectrochemistry

A novel NH₂⁺ ion implantation‐modified indium tin oxide (NH₂/ITO) electrode was prepared. Acid‐pretreated, negatively charged MWNTs were firstly modified on the surface of NH₂⁺ ion implantation electrode, then, positively charged Mb was adsorbed onto MWNTs films by electrostatic interaction. The assembly of MWNTs and Mb was characterized with electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The immobilized Mb showed a couple of quasireversible cyclic voltammetry peaks in pH 7.0 phosphate buffer solution (PBS). The apparent surface concentration of Mb at the electrode surface was 1.06×10^?9 mol cm^?2. The Mb/MWNTs/NH₂/ITO electrode also gave an improved electrocatalytic activity towards the reduction of hydrogen peroxide. The catalysis currents increased linearly to the H₂O₂ concentration in a wide range from 9×10^?7 to 9.2×10^?5 M with a correlation coefficient of 0.999. The detection limit was 9.0×10^?7 M. The experiment results demonstrated that the modified electrode provided a biocompatible microenvironment for protein and supplied a necessary pathway for its direct electron transfer.     

Amperometric Sensor for Trichloroacetic Acid Based on Myoglobin/Colloidal Gold Nanoparticles Immobilized in Titania Sol–Gel Matrix

A new amperometric sensor for the determination of trichloroacetic acid (TCA) was developed based on the immobilization of myoglobin/colloidal gold nanoparticles in titania sol–gel matrix. The sensor showed a pair of well‐defined and nearly reversible cyclic voltammetric peaks for the Mb Fe(III)/Fe(II) with a formal potential (E°′) of ?335 mV and a peak‐to‐peak separation was 61 mV vs. Ag/AgCl (3.0 M KCl) at 100 mV s^?1 in 0.1 M pH 7.0 phosphate buffer solutions (PBS). The formal potential of the Mb Fe(III)/Fe(II) couple shifted linearly with the pH with a slope of ?51.3 mV/pH, indicating that an electron transfer accompanies single‐proton transportation. The sensor displayed a good electrocatalytic response toward the reduction of TCA and the catalytic mechanism was also discussed. The overpotential for the reduction of TCA was lowered by at least 0.8 V compared with that obtained at bare glassy carbon electrode. The linear range spans the concentration of TCA from 2.0×10^?6 to1.2×10^?5 M and the detection limit was 1.2×10^?7 M. In addition, the stability, repeatability and selectivity of the sensor were also evaluated.     

Planar thiol-sensitive sensor elements for the determination of butyrylcholinesterase activity and analysis of its inhibitors

A method for the analysis of the thiocholine concentration, as well as the activity of the butyrylcholinesterase (BChE) enzyme and its inhibitors, using thiol-sensitive planar sensors has been proposed. Thiocholine sensitivity of the sensors was achieved by a mediator layer of manganese dioxide formed on a working carbon electrode. The detection limits for BChE and its inhibitor diazinon were 1 × 10^?10 M and 1 × 10^?9 M, respectively. The approach that was developed simplifies the analysis of inhibitors. It could be used for water quality and environmental monitoring.     

Acetylferrocene Modified Carbon Paste Electrode; A Sensor for Electrocatalytic Determination of Hydrazine

The electrocatalytic oxidation of hydrazine at a carbon paste electrode spiked with acetylferrocene as a mediator was studied by cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. In contrast to other ferrocenic compounds, acetylferrocene exhibits a chemical irreversible behavior, but it can act as an effective mediator for electrocatalytic oxidation of hydrazine, too. The heterogeneous electron transfer rate constant between acetylferrocene and the electrode substrate (carbon paste) and the diffusion coefficient of spiked acetylferrocene in silicon oil were estimated to be about 3.45×10^?4 cm s^?1 and 4.45×10^?9 cm² s^?1, respectively. It has been found that under the optimum conditions (pH 7.5) the oxidation of hydrazine occurs at a potential of about 228 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak current of hydrazine was linearly dependent on its concentration and the obtained linear range was 3.09×10^?5 M–1.03×10^?3 M. The detection limit (2σ) has been determined as 2.7×10^?5 M by cyclic voltammetry. Also, the peak current was increased linearly with the concentration of hydrazine in the range of 1×10^?5 M–1×10^?3 M by differential pulse voltammetry with a detection limit of 1×10^?5 M. This catalytic oxidation of hydrazine has been applied as a selective, simple, and precise new method for the determination of hydrazine in water samples.     

A New Amperometric Carbon Paste Enzyme Electrode for Ethanol Determination

Abstract

In this study, a new amperometric carbon paste enzyme electrode for determination of ethanol was developed. The carbon paste was prepared by mixing alcohol dehydrogenase, its coenzyme nicotinamide adenine dinucleotide (oxidized form, NAD⁺), poly(vinylferrocene) (PVF) that was used as a mediator, graphite powder and paraffin oil, then the paste was placed into cavity of a glass electrode body. Determination of ethanol was performed by oxidation of nicotinamide adenine dinucleotide (reduced form, NADH) generated enzymatically at +0.7 V. The effects of enzyme, coenzyme and PVF amounts; pH; buffer concentration and temperature were investigated. The linear working range of the enzyme electrode was 4.0×10^?4–4.5×10^?3 M, determination limit was 3.9×10^?4 M and response time was 50 s. The optimum pH, buffer concentration, temperature, and amounts of enzyme, NAD⁺ and PVF for enzyme electrode were found to be 8.5, 0.10 M, 37°C, 2.0, 6.0, and 12.0 mg, respectively. The storage stability of enzyme electrode at +4°C was 7 days. Enzyme electrode was used for determination of ethanol in two different wine samples and results were in good agreement with those obtained by gas chromatography.     

Amperometric Lactate Biosensor Based on Carbon Paste Electrode Modified with Benzo[c]cinnoline and Multiwalled Carbon Nanotubes

Amperometric lactate biosensor based on a carbon paste electrode modified with benzo[c]cinnoline and multiwalled carbon nanotubes is reported. Incorporation of benzo[c]cinnoline acting as a mediator and multiwalled carbon nanotubes providing a conduction pathway to accelerate electron transfer due to their excellent conductivity into carbon paste matrix resulted in a high performance lactate biosensor. The resulting biosensor exhibited a fast response, high selectivity, good repeatability and storage stability. Under the optimal conditions, the enzyme electrode showed the detection limit of 7.0×10^?8 M with a linear range of 2.0×10^?7 M–1.1×10^?4 M. The usefulness of the biosensor was demonstrated in serum samples.     

Fabrication of an optical sensor based on the immobilization of Qsal on the plasticized PVC membrane for the determination of copper(II)

A novel optical sensor has been proposed for sensitive determination of Cu(II) ion in aqueous solutions. The copper sensing membrane was prepared by incorporating Qsal (2-(2-hydroxyphenyl)-3H-anthra[2,1-d]imidazole-6,11-dione) as ionophore in the plasticized PVC membrane containing tributyl phosphate (TBP) as plasticizer. The membrane responds to Cu(II) ion by changing color reversibly from yellow to dark red in acetate buffer solution at pH 4.0. The proposed sensor displays a linear range of 6.3 × 10^?7?1.00 × 10^?4 M with a limit of detection of 3.3 × 10^?7 M. The response time of the optical sensor was about 3?C5 min, depending on the concentration of Cu(II) ions. The selectivity of the optical sensor to Cu(II) ions in acetate buffer is good. The sensor can readily be regenerated by hydrochloric acid (0.1 M). The optical sensor is fully reversible. The proposed optical sensor was applied to the determination of Cu(II) in environmental water samples.     

Sol‐Gel‐Derived Biosensor Based on Plant Tissue: The Inhibitory Effect of Atrazine on Polyphenol Oxidase Activity for Determination of Atrazine

This work presents a sol‐gel based biosensor for atrazine determination which has been obtained by introducing the enzyme polyphenol oxidase from apple tissue in a sol‐gel matrix. Apple tissue acts as a molecular recognition element. Atrazine is an inactive compound electrochemically; redox coupling of dopamine was used for studying atrazine behavior. Atrazine was determined by monitoring the inhibition power of polyphenol oxidase activity. The measurements were performed in 0.1 M KH₂PO₄‐NaOH buffer (pH 7.5). The effect of various experimental parameters such as pH, concentration of buffer, concentration of dopamine, incubation time and matrix composition has been investigated for optimum analytical performance. The biosensor consisted of 10.3% (w/w) of apple tissue. The bioelectrode exhibits a linear response for dopamine and atrazine concentrations in the range of 5.66 × 10^?6?2.27 × 10^?3M and 1 × 10^?5 ?1 × 10^?4 M with a detection limit of 4.2 × 10^?6 and 5.5 × 10^?6 M, respectively. A correlation coefficient of 0.9945 and a relative standard deviation (R.S.D.) of 3.29% for dopamine, 0.9944 and 3.69% for a trazine were achieved.     

Flow-injection determination of l-tyrosine in serum with an immobilized tyrosinase reactor and fluorescence detection

Tyrosinase is immobilized on controlled-pore glass beads and packed into a stainless-steel column (5 cm × 4 mm i.d.). Serum is deproteinized with tungstate and sulphuric acid. The carrier stream is 0.3 M phosphate buffer (pH 7.2), and is mixed with 5 M potassium hydroxide after the enzyme reactor. The fluorescent dihydroxyindole formed is detected at 490 nm (excitation at 375 nm). The calibration graph is linear for 1 × 10^?7 ?1 × 10^?4 M tyrosine; the detection limit is 2 × 10^?8 M.     

Synthesis and Electrochemical Investigation of Tetra Amino Cobalt (II) Phthalocyanine Functionalized Polyaniline Nanofiber for the Selective Detection of Dopamine

A new electrochemical sensing platform based on tetra‐amino cobalt (II) phthalocyanine (TACoPc) ingrained polyaniline (PANI) nanofiber composite (TACoPc/PANI hybrid) has been developed for the selective detection of dopamine. The uniform fibrous network of PANI/TACoPc hybrid was synthesized by a one‐step oxidative polymerization at room temperature. The synthesized nanocomposite was characterized using field emission scanning electron microscopy (FESEM), energy dispersive X‐ray (EDX), fourier transmission infrared spectroscopy (FTIR), raman spectroscopy, X‐ray diffraction (XRD) and UV‐Visible spectroscopy. The electrochemical behavior of the TACoPc/PANI hybrid material was studied by using different electrochemical techniques, including cyclic voltammetry (CV) and chronoamperometry in 0.1 M phosphate buffer solution (PBS) of pH 7 by modifying the glassy carbon electrode (GCE). Due to the synergistic impact of PANI and TACoPc, the suggested altered electrode provided superior catalytic performance for dopamine even in the presence of ascorbic acid. It exhibited a linear reaction with a high sensitivity of 1.212 μA/μM cm^?2 and a low detection limit of 0.064 μM over the 20–200 μM concentration range in 0.1 M PBS. One of the commonly faced problems of interference of ascorbic acid and uric acid in the electrochemical detection of dopamine was completely excluded from this modified electrode which led to an increase in the catalytic activity of the material for the detection of dopamine in the presence of ascorbic acid.