Nanobiocomposite Modified Carbon‐Ceramic Electrode Based on Nano‐TiO2‐Plant Tissue and Its Application for Electrocatalytic Oxidation of Dopamine

A new modified carbon‐ceramic electrode was prepared by incorporating TiO₂ nanoparticle into sol‐gel network by accompanying apple tissue. A mixture of fine graphite powder with 15 wt% of TiO₂ nanoparticle was used for the preparation of the carbon matrix and finally modification with a known amount weighted of apple tissue. The apple tissue containing polyphenol oxidase enzyme acts as molecular recognition element. The electrocatalytic oxidation of dopamine was investigated on the surface of the nanobiocomposite modified carbon‐ceramic electrode using cyclic voltammetry, chronoamperometry and amperometry techniques. Effect of pH, scan rate, TiO₂ percentage on the response of modified electrode was studied. The prepared modified electrode presented a linear range for dopamine from 5.0×10^?6 to 1.2×10^?3 M in buffered solutions with pH 7.4 by amperometry. The detection limit was 3.41×10^?6 M dopamine. The response of the modified carbon‐ceramic electrode and unmodified carbon‐ceramic electrode was compared.     

New Electrochemical Sensor of Prolonged Application for Metformin Determination Based on Hydrated Ruthenium Dioxide‐Carbon Black‐Nafion Modified Glassy Carbon Electrode

Metformin (MET) is an antidiabetic drug most commonly used in treatment of diabetes mellitus type 2 (T2D). Adsorptive stripping voltammetric method using carbon black – hydrated ruthenium dioxide – Nafion modified glassy carbon electrode (CB‐RuO₂‐Nafion GC electrode) have been developed for metformin determination in pharmaceutical formulations. By using ruthenium dioxide, electrode's lifespan was extended to at least 3 weeks (change of metrological parameters estimated as 3–4 %) what is an excellent result concerning other solutions previously described in the literature. Moreover the fabrication of the sensor is simple and fast. Deposition step was carried out at the potential 0 mV for 15 s. The best results were obtained in 0.05 M acetate buffer (pH 4.6). Important aspect was fixed MET : Cu(II) ratio equal to 1 : 8, otherwise linear dependence between register current and MET concentration could not be obtained. In addition, a significant improvement in the parameters of the calibration curve was obtained. Limit of detection was equal to 0.7 μM. Developed method was successfully applied in analysis of 2 pharmaceuticals products and in wastewater and river water. Accuracy of the method was estimated using recoveries, which were in the range 101–110 %. In order to adapt developed system into hydrodynamic conditions, amperometry in hydrodynamic transport conditions and flow injection analysis (FIA) measurements have been conducted. Conducted FIA measurements prove that developed method has potential for application in automized flow systems without frequent calibration.     

Electrochemical Behavior of Herbal Antitumor Drug Aloe‐Emodin at Carbon‐Coated Nickel Magnetic Nanoparticles Modified Glassy Carbon Electrode

The electrochemical behavior of aloe‐emodin (AE), an important herbal antitumor drug, was investigated at a carbon‐coated nickel magnetic nanoparticles modified glassy carbon electrode (CNN/GCE). A couple of well‐defined redox peaks was obtained. Some electrochemical parameters of AE at a CNN/GCE, such as the charge number, exchange current density, standard heterogeneous rate constant, were measured. The square wave voltammetry (SWV) response of AE was linear with the concentration over two concentration intervals viz. 6.24×10^?9?1.13×10^?6 M and 1.13×10^?6?1.23×10^?5 M, with a detection limit of 2.08 nM. A fast, simple and sensitive detection and analysis of AE was developed.     

Nanocellulose/Carbon Nanoparticles Nanocomposite Film Modified Electrode for Durable and Sensitive Electrochemical Determination of Metoclopramide

A novel electrochemical sensor based on nanocellulose‐carbon nanoparticles (NC‐CNPs) nanocomposite film modified glassy carbon electrode (GCE) is developed for the analysis of metoclopramide (MCP). Atomic force microscopy, scanning electron microscopy and electrochemical impedance spectroscopy were used to characterize the roughness, surface morphology and performance of the deposited modifier film on GCE. SEM image demonstrated that modifier nanoparticles are uniformly deposited on GCE, with an average size of less than 50 nm. The electrochemical behavior of MCP and its oxidation product is studied using linear sweep and cyclic voltammetry over a wide pH range on NC‐CNPs modified glassy carbon electrode. The results revealed that the oxidation of MCP is an irreversible and pH‐dependent process that proceeds in an adsorption‐controlled mechanism and results in the formation of a main oxidation product, which adsorbs on the surface of NC‐CNPs/ GCE. The modified electrode showed a distinctive anodic response towards MCP with a considerable enhancement (49 fold) compared to the bare GCE. Under the optimized conditions, the modified electrode exhibited a wide linear dynamic range of 0.06–2.00 µM with a detection limit of 6 nM for the voltammetric determination of MCP. The prepared modified electrode showed several advantages such as simple preparation method, high stability, reproducibility, and repetitive usability. The modified electrode is successfully applied for the accurate determination of trace amounts of MCP in pharmaceutical and clinical preparations.     

A Reagentless Amperometric Immunosensor for Alpha‐Fetoprotein Based on Gold Nanoparticles/TiO2 Colloids/Prussian Blue Modified Platinum Electrode

A novel reagentless amperometric immunosensor for the determination of alpha‐fetoprotein (AFP) was prepared by immobilizing TiO₂ colloids on Prussian blue (PB) modified platinum electrode, which yielded a positively charged interface with strong adsorption to deposit gold nanoparticles for immobilization of alpha‐fetoprotein antibody (anti‐AFP). The factors influencing the performance of the proposed immunosensors were studied in detail. Under the optimized conditions, cyclic voltammograms determination of AFP showed a specific response in two concentration ranges from 3.0 to 30.0 ng/mL and from 30.0 to 300.0 ng/mL with a detection limit of 1.0 ng/mL at a signal‐to‐noise ratio of 3. The proposed immunosensor exhibited high selectivity, good reproducibility, long‐term stability (>2 months) and good repeatability.     

Enhanced Anodic Electrochemiluminescence of Dissolved Oxygen with 2‐(Dibutylamino) ethanol at TiO2 Nanoparticles Modified Platinum Electrode for Dopamine Detection

The anodic electrochemiluminescence (ECL) of dissolved oxygen with 2‐(dibutylamino) ethanol (DBAE) on platinum electrode has been reported previously by our group. Interestingly, the ECL intensity can be greatly amplified at TiO₂ nanoparticles modified platinum electrode (TiO₂/Pt), which is due to the catalytic effect of TiO₂ nanoparticles to electrochemical oxidation of DBAE. It is the first case to obtain the enhanced ECL from luminophor by electrochemical catalysis of co‐reactant. The enhanced anodic ECL intensity can be quenched by dopamine sensitively. And the ECL intensity versus the logarithm of concentration of dopamine was linear over the 4.0×10^?12–1.8×10^?8 M (R²=0.9957), with the limit of detection of 2.7×10^?12 M (S/N=3).     

A Polypyrrole‐Imprinted Electrochemical Sensor Based on Nano‐SnO2/Multiwalled Carbon Nanotubes Film Modified Carbon Electrode for the Determination of Oleanolic Acid

A sensitive molecularly imprinted electrochemical sensor with specific recognition ability for oleanolic acid was synthesized by modification of multiwalled carbon nanotubes (MWNTs) decorated with tin oxide nanoparticles (nano‐SnO₂/MWNTs) and polypyrrole‐imprinted polymer on a carbon electrode. The morphology and electrochemical performance of the imprinted sensor were investigated by using scanning electron microscope (SEM), X‐ray diffraction (XRD), cyclic voltammetry (CV), linear sweep voltammetry (LSV) and amperometric i–t curve. The results showed that the imprinted sensor displayed excellent selectivity toward oleanolic acid. A linear relationship between the response currents and oleanolic acid concentrations ranging from 5.0×10^?8 g/L to 2.0×10^?5 g/L was obtained for the imprinted sensor. The limit of detection (LOD) of the imprinted sensor toward oleanolic acid was calculated as 8.6×10^?9 g/L at a signal to noise ratio (S/N) of 3. This imprinted sensor was successfully applied to the determination of oleanolic acid in Acitinidia deliciosa root samples.     

Screen‐printed Electrode Modified with ZnFe2O4 Nanoparticles for Detection of Acetylcholine

In this paper a sensor to detect acetylcholine on the basis of ZnFe₂O₄ nanoparticles modified screen printed electrode (SPE) is reported. In the range 0.08–500.0 μM, with the detection limit of 0.024±0.001 μM, acquired anodic peak currents where shown to be linearly dependent on acetylcholine concentrations by differential pulse voltammetry (DPV). It was proven that acetylcholine oxidation at adjusted electrode surface takes place at 100 mV potential less positive compared to an unadjusted screen printed electrode. The electron transfer coefficient (α=0.51) and diffusion coefficient (D=9.3×10^?6 cm²/s) of acetylcholine oxidation were determined too. In addition, this original sensor possesses numerous benefits such as reproducibility, high stability and rapid response (20 s).     

Electrochemical Determination of 2‐Nitrophenol in Water Samples Using Mg‐Al‐SDS Hydrotalcite‐Like Clay Modified Glassy Carbon Electrode

A glassy carbon electrode (GCE) modified with Mg‐Al‐SDS hydrotalcite‐like clay (SDS‐HTLC) was used for the sensitive voltammetric determination of 2‐nitrophenol (2‐NP) utilizing the oxidation process. The results indicate the prepared modified electrode has an excellent electrocatalytic activity toward 2‐NP oxidation, lowering the oxidation overpotential and increasing the oxidation current. Under optimal conditions, the oxidation current was proportional to 2‐NP concentration in the range from 1.0×10^?6 to 6.0×10^?4 M with the detection limit of 5.0×10^?7 M by DPV (S/N=3). The fabricated electrode was applied for 2‐NP determination in water samples and the recovery for these samples was from 95.6 to 103.5%.     

Nano TiO2 Modified Carbon‐ceramic Electrode and Its Application for Electrocatalytic Oxidation of NADH

The electrocatalytic oxidation of nicotinamide adenine dinucleotide (NADH) was studied on nanoTiO₂ modified sol‐gel electrode, using cyclic voltammetry, chronoamperometry and differential pulse voltammetry as diagnostic techniques. It is demonstrated that TiO₂ nanoparticles on sol‐gel network catalyze the oxidation of NADH in the absence of any electron transfer mediators. Effect of various parameters such as pH, scan rate, TiO₂ percentage on the response of modified electrode was studied. In addition, scanning electron microscopy (SEM) was used to characterize the surface morphology of the spots. A dynamic range between 0.5–50 μM with detection limit of 0.35 μM was obtained with DPV studies. This method was successfully used for determination of NADH in cucumber cotyledons samples. The electrode showed relatively good stability over more than 2 months.     

Poly(Taurine‐Glutathione)/Carbon Nanotube Modified Glassy Carbon Electrode as a New Levofloxacin Sensor

A new highly sensitive and selective electrochemical levofloxacin sensor based on co‐polymer‐carbon nanotube composite electrode was developed. Taurine and Glutathione were electrochemically co‐polymerized on multiwalled carbon nanotubes modified glassy carbon electrode (Poly(TAU‐GSH)/CNT/GCE) and used as a levofloxacin sensor in pH 6 phosphate buffer solution. The new composite electrode surfaces were characterized by scanning electron microscopy, atomic force microscopy and electrochemical impedance spectroscopy. Under the optimized conditions, two linear segments were obtained for increasing LEV concentrations between 20 nmol L^?1‐1 μmol L^?1 and 1.5 μmol L^?1‐55 μmol L^?1 LEV with a detection limit of 9 nmol L^?1 using amperometry. Poly(TAU‐GSH)/CNT/GCE exhibited high sensitivity, selectivity with good stability. The new sensor was employed for real samples of LEV tablets and urine. Promising results were obtained with good accuracy which were also in accordance with LC‐MS/MS analysis.     

Improved Sensing of Capsaicin with TiO2 Nanoparticles Modified Epoxy Graphite Electrode

The presented research focuses on the electrochemical determination of capsaicin, a lipophilic alkaloid which originates hotness in chili peppers. An electrochemical sensor based on epoxy‐graphite composite with the modification of titanium dioxide (TiO₂) nanoparticles is developed for the determination of this alkaloid. The measurements were carried out in glycine buffer at pH 2.5 using cyclic voltammetry. Two linear concentration ranges were obtained from 6 to 75 μM (R=0.99) and from 12 to 138 μM, with a detection limit of 5.34 μM and 11.3 μM capsaicin, for 1^st and 2^nd oxidation peak, respectively. The main advantage of developed sensor is its repeatability and robustness against fouling; the relative standard deviation (RSD) value was 2.53 % (n=10). This voltammetric sensing procedure has successfully been applied to quantify capsaicin in various real samples such as hot chili sauce and pharmaceutical preparations.     

Electrochemistry and Electrocatalysis of a Nafion/Nano‐CaCO3/Hb Film Modified Carbon Ionic Liquid Electrode Using BMIMPF6 as Binder

In this paper a room temperature ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆) was used as binder for the construction of carbon ionic liquid electrode (CILE) and a new electrochemical biosensor was developed for determination of H₂O₂ by immobilization of hemoglobin (Hb) in the composite film of Nafion/nano‐CaCO₃ on the surface of CILE. The Hb modified electrode showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa and E_pc as ?0.265 V and ?0.470 V (vs. SCE). The formal potential (E°′) was got by the midpoint of E_pa and E_pc as ?0.368 V, which was the characteristic of Hb Fe(III)/Fe(II) redox couples. The peak to peak separation was 205 mV in pH 7.0 Britton–Robinson (B–R) buffer solution at the scan rate of 100 mV/s. The direct electrochemistry of Hb in the film was carefully investigated and the electrochemical parameters of Hb on the modified electrode were calculated as α=0.487 and k_s=0.128 s^?1. The Nafion/nano‐CaCO₃/Hb film electrode showed good electrocatalysis to the reduction of H₂O₂ in the linear range from 8.0 to 240.0 μmol/L and the detection limit as 5.0 μmol/L (3σ). The apparent Michaelis–Menten constant (K_M^app) was estimated to be 65.7 μmol/L. UV‐vis absorption spectroscopy and FT‐IR spectroscopy showed that Hb in the Nafion/nano‐CaCO₃ composite film could retain its native structure.     

基于纳米二氧化锆与铂微粒复合修饰玻碳电极的甲醛传感器研究

采用循环伏安法在玻碳电极表面依次电沉积纳米二氧化锆和铂微粒,制备了一种检测甲醛的新型电化学传感器。用电镜扫描对该修饰电极表面进行了表征,循环伏安法和线性扫描伏安法研究了甲醛在该修饰电极上的电催化氧化作用,优化了实验参数。结果表明,该修饰电极对甲醛有很好的电催化氧化作用,在0.1 mol/L H2SO4溶液中,甲醛的氧化峰电流与其浓度在1.0×10-6~5.0×10-3mol/L范围内呈良好线性关系,回归方程为Ip(μA)=79.95+2.005×105c(mol/L),相关系数r=0.999 3,检出限为5.0×10-7mol/L。     

Enhanced Electrochemiluminescence of TiO2 Nanoparticles Modified Electrode by Nafion Film and Its Application in Selective Detection of Dopamine

In this work, a simple and effective approach to obtain stable, nontoxic and strong electrochemiluminescence (ECL) interfaces is provided by coating TiO₂ nanoparticles (NPs) modified glassy carbon electrode (GCE) surfaces with Nafion. Unlike a decrease of the current resulting from the blocked diffusion usually displayed in electrochemical processes by Nafion coating, a Nafion/TiO₂ NPs modified electrode not only shows a highly stable ECL, but also shows an 8‐fold increase of ECL intensity and a reduction of the overpotential of ca. 300 mV in the presence of K₂S₂O₈ as co‐reactant, compared with those of bare TiO₂ NPs modified electrodes. The roles of Nafion coating on TiO₂ NPs in the ECL process are proposed to be twofold: to provide refuge for the free radicals and to enhance the electron‐hole recombination. Benefiting from its excellent ECL performance, the cationic exchange function of Nafion and the susceptible to being oxidized performance of dopamine (DA) by holes, the Nafion/TiO₂ composite electrode could be used to sensitively and selectively detect DA with a detection limit of 1.0×10^?11 M and a linear range of 1.0×10^?11–6.0×10^?7 M. The coexisting anionic species such as excess ascorbic acid show little interference on DA detection.     

Electrochemical Morphine Sensor Based on Gold Nanoparticles Metalphthalocyanine Modified Carbon Paste Electrode

Composites of gold nanoparticles (Au) electrochemically deposited and different metal phthalocyanines (Co, Ni, Cu, and Fe) were chemically prepared. The composites were used as modifiers for carbon paste electrodes and were used for the determination of morphine in presence of ascorbic acid and uric acid. Central metal atoms of phthalocyanine moiety affected the rate of electron transfer. Thus, the electroactivity of different modifiers were evaluated towards morphine oxidation. Au‐CoPcM‐CPE possessed the highest rate for charge transfer rate in all studied pH electrolytes. Limit of detection was 5.48×10^?9 mol L^?1 in the range of 4.0×10^?7 to 9.0×10^?4 mol L^?1.     

Fabrication of Au‐Nanoparticle/TiO2‐Nanotubes Electrodes Using Electrochemical Methods and Their Application for Electrocatalytic Oxidation of Hydroquinone

Gold nanoparticle (Au‐NPs)‐Titanium oxide nanotube (TiO₂‐NTs) electrodes are prepared by using galvanic deposition of gold nanoparticles on TiO₂‐NTs electrodes as support. Scanning electron microscopy and energy‐dispersive X‐ray spectroscopy results indicate that nanotubular TiO₂ layers consist of individual tubes of about 60–90 nm diameters and gold nanoparticles are well‐dispersed on the surface of TiO₂‐NTs support. The electrooxidation of hydroquinone of Au‐NPs/TiO₂‐NTs electrodes is investigated by different electrochemical methods. Au‐NPs/TiO₂‐NTs electrode can be used repeatedly and exhibits stable electrocatalytic activity for the hydroquinone oxidation. Also, determination of hydroquinone in skin cream using this electrode was evaluated. Results were found to be satisfactory and no matrix effects are observed during the determination of hydroquinone content of the “skin cream” samples.     

Application of a Modified CuO Nanoparticles Carbon Paste Electrode for Simultaneous Determination of Isoperenaline,Acetaminophen and N‐acetyl‐L‐cysteine

A 1‐[2‐hydroxynaphthylazo]‐6‐nitro‐2‐naphthol‐4‐sulfonate/ CuO nanoparticles modified carbon paste electrode (HNNSCCPE) was constructed and the electro‐oxidation of isoprenaline at the surface of the modified electrode was studied using cyclic voltammetry (CV), chronoamperometry (CHA), and square wave voltammetry (SWV). Under the optimized conditions, the square wave voltammetric peak current of isoprenaline increased linearly with isoprenaline concentrations in the range of 1.0×10^?7 to 7.0×10^?4 M and detection limit of 5.0×10^?8 M was obtained for isoprenaline. The prepared modified electrode exhibits a very good resolution between the voltammetric peaks of isoprenaline, acetaminophen and N‐acetyl‐L‐cysteine which makes it suitable for the detection of isoprenaline in the presence of acetaminophen and N‐acetyl‐L‐cysteine in real samples.     

Direct Electrochemistry and Electrocatalysis of Hemoglobin/ZnO‐Chitosan/nano‐Au Modified Glassy Carbon Electrode

The highly efficient H₂O₂ biosensor was fabricated on the basis of the complex films of hemoglobin (Hb), nano ZnO, chitosan (CHIT) dispersed solution and nano Au immobilized on glassy carbon electrode (GCE). Biocompatible ZnO‐CHIT composition provided a suitable microenvironment to keep Hb bioactivity (Michaelis‐Menten constant of 0.075 mmol L^?1). The presence of nano Au in matrix could effectively enhance electron transfer between Hb and electrode. The electrochemical behaviors and effects of solution pH values were carefully examined in this paper. The (ZnO‐CHIT)‐Au‐Hb/GCE demonstrated excellently electrocatalytical ability for H₂O₂. This biosensor had a fast response to H₂O₂ less than 4 s and excellent linear relationships were obtained in the concentration range from1.94×10^?7 to 1.73×10^?3 mol L^?1 with the detection limit of 9.7×10^?8 mol L^?1 (S/N=3) under the optimum conditions. Moreover, the stability and reproducibility of this biosensor were evaluated with satisfactory results.     

Electrochemical Studies of Oxidation of Lomefloxacin and Interaction with Calf Thymus DNA at Nano‐SnO2/DHP Modified Electrode

A nanoparticle thin film modified electrode has been constructed using a glassy carbon electrode (GCE) coated with a nano‐tin oxide/dihexadecylphosphate (nano‐SnO₂/DHP). In pH 6.0 phosphate buffer solutions (PBS), lomefloxacin (LMF) appeared as an anodic peak with peak potential of 1.35 V at nano‐SnO₂/DHP modified electrode. In comparison with a bare GCE or a nano‐SnO₂ modified electrode, the nano‐SnO₂/DHP modified electrode exhibited an enhanced effectiveness for the oxidation of LMF. Cyclic voltammetry (CVs) coupled with fluorescence and UV/vis absorbance spectra techniques were used to study the interaction of LMF with Calf thymus DNA (ctDNA) in phosphate buffer solutions (PBS). The interaction of LMF and ctDNA could result in a considerable decrease in the peak currents and positive shift in the peak potential, as well as changes of fluorescence, UV/vis adsorption spectra and gel electrophoresis. All the acquired data showed that the new adduct between LMF and ctDNA was formed. Electrochemistry coupled with spectroscopy techniques could provide a relatively easy way to obtain useful information about the molecular mechanism of LMF‐ctDNA interactions.