Synthesis of Novel CuO Nanosheets with Porous Structure and Their Non‐Enzymatic Glucose Sensing Applications

Novel CuO thin films composed of porous nanosheets were in situ formed on indium tin oxide (ITO) by a simple, low temperature solution method, and used as working electrodes to construct nonenzymatic glucose sensor after calcinations. Cyclic voltammetry revealed that the CuO/ITO electrode calcinated at 200 °C exhibited better electrocatalytic activity for glucose. For the amperometric glucose detection, such prepared electrode showed low operating potential of 0.35 V and high sensitivity of 2272.64 μA mM^?1 cm^?2. Moreover, the CuO/ITO electrode also showed good stability, reproducibility and high anti‐interference ability. Thus, it is a promising material for the development of non‐enzymatic glucose sensors.     

Chemical Adsorption onto an ITO Substrate of Single‐Wall Carbon Nanotube Functionalized by Carboxylic Groups as an Efficient Support for Electrocatalyst

A single‐wall carbon nanotube functionalized by carboxylic groups (SWNT‐CA) was found to be adsorbed on an indium tin oxide (ITO) electrode by chemical interaction between carboxylic groups and the ITO surface. The adsorption experiments indicated that the narrow pH conditions (around pH 3.0) exist for its adsorption which is restricted by preparation of stable fluid dispersion (favorable at higher pH) and by the chemical interaction (favorable at lower pH). Atomic force microscopic (AFM) measurements suggest that fragmented SWNT‐CA are adsorbed, primarily lying on the surface. Electrochemical impedance analysis indicated that an electrochemical double layer capacitance of the SWNT‐CA/ITO electrode is considerably higher than that for the ITO electrode, suggesting that the interfacial area between the electrode surface and the electrolyte solution is enlarged by the SWNT‐CA layer. Pt particles were deposited as a catalyst on the bare ITO and SWNT‐CA‐coated ITO (SWNT‐CA/ITO) electrodes to give respective Pt‐modified electrodes (denoted as a Pt/ITO electrode and a Pt/SWNT‐CA/ITO electrode, respectively). The cathodic current for the Pt/SWNT‐CA/ITO electrode was 1.7 times higher than that for the Pt/ITO electrode at 0.0 V, showing that the Pt/SWNT‐CA/ITO electrode works more efficiently for O₂ reduction at 0.0 V due to the SWNT‐CA layer. The enhancement by the SWNT‐CA layer is also effective for electrocatalytic proton reduction. It could be ascribable to the enlarged interfacial area between the electrode surface and the electrolyte solution.     

Time-resolved particle image velocimetry analysis and computational modeling of transient optically induced electrothermal micro vortex

Trapping, sorting, transportation, and manipulation of synthetic microparticles and biological cells enable investigations in their behavior and properties. Microfluidic techniques like rapid electrokinetic patterning (REP) provide a non-invasive means to probe into the nature of these micro and nanoparticles. The opto-electrically induced nature of a REP micro vortex allows tuning of the trap characteristics in real-time. In this work, we studied the effects of transient optical heating on the induced electrothermal vortex using micro-particle image velocimetry (μ-PIV) and computational modeling. A near infra-red (980 nm) laser beam was focused on a colloidal suspension of 1 μm polystyrene beads sandwiched between two parallel-plate electrodes. The electrodes were subjected to an AC current. The laser spot was scanned back-and-forth in a line, at different frequencies, to create the transient vortex. This phenomenon was also studied with a computational model made using COMSOL Multiphysics. We visualize fluid flow in custom-shaped REP traps by superposing multiple axisymmetric (spot) vortices and discuss the limitations of using superposition in dynamically changing traps.     

汞修饰掺锡三氧化二铟导电玻璃光透薄层电化学池的设计

报道了汞膜修饰掺锡三氧化二铟导电玻璃电极的制备及其薄层电化学池的设计，测试限电极和薄层的光、电化学性能，在水溶液中，与基底电极相比，该电极的负电位范围增加了７００ｍＶ，并表现出普通汞电极的电化学 性质，以此电极制得的电极制得的薄层层池可适用于氧化还原电位较负的电化学过程的光谱电化学研究及金属离子的电化学分析。     

Lightweight ITO Electrodes Decorated with Gold Nanostructures for Electrochemical Applications

Gold nanostructures were fabricated on a transparent indium tin oxide (ITO) coated PET substrate by an electrodeposition technique from a potassium gold (III) chloride solution for two different types of applications. It was found that the optical transparency of lightweight ITO electrodes could be maintained by depositing isolated gold nanostructures while opening up the use of these electrodes for inner sphere electron reactions, such as hydroquinone oxidation, which are not possible at ITO electrodes. For practical applications the adhesion of gold to the ITO electrode was improved by modifying the ITO surface with 3‐mercaptopropyl‐trimethoxysilane (MPS). Compared to Au/ITO, the Au/MPS/ITO electrode showed vastly improved electrochemical activity toward various electron transfer reactions when subjected to mechanical stress. The biosensing properties of the Au/MPS/ITO electrode was also investigated by studying the detection of immobilized DNA on the Au/MPS/ITO electrode via electrochemical impedance spectroscopy (EIS).     

An Air‐breathing Carbon Cloth‐based Screen‐printed Electrode for Applications in Enzymatic Biofuel Cells

We report a prototype air‐breathing carbon cloth‐based electrode that was fabricated starting from a commercially available screen‐printed electrode equipped with a transparent ITO working electrode (DropSens, ref. ITO10). The fabrication of the air‐breathing electrodes is straightforward, shows satisfactory reproducibility and a good electrochemical response as evaluated by means of [Fe(CN)₆]^3?/4? voltammetry. The gas‐diffusion electrodes were successfully modified with the O₂ reducing enzyme bilirubin oxidase from Myrothecium verrucaria in a direct electron transfer regime. The enzyme modified electrodes showed a remarkable high current density for O₂ reduction in passive air‐breathing mode of up to 5 mA cm^?2. Moreover, the enzyme modified electrodes were applied as O₂ reducing biocathodes in a glucose/air enzymatic biofuel cell in combination with a high current density glucose oxidase/redox polymer bioanode. The biofuel cell provides a high maximum power density of (0.34±0.02) mW cm^?2 at 0.25 V. The straightforward design, low cost and the high reproducibility of these electrodes are considered as basis for standardized measurements under gas‐breathing conditions and for high throughput screening of gas converting (bio‐)catalysts.     

Platform for Highly Sensitive Alkaline Phosphatase‐Based Immunosensors Using 1‐Naphthyl Phosphate and an Avidin‐Modified Indium Tin Oxide Electrode

We report a versatile platform for highly sensitive alkaline phosphatase (ALP)‐based electrochemical biosensors that uses an avidin‐modified indium tin oxide (ITO) electrode as a sensing electrode and 1‐naphthyl phosphate (NPP) as an ALP substrate. Almost no electrocatalytic activity of NPP and good electrocatalytic activity of 1‐naphthol (ALP product) on the ITO electrodes allow a high signal‐to‐background ratio. The effective surface covering of avidin on the ITO electrodes allows very low levels of nonspecific binding of proteins to the sensing electrodes. The platform technology is used to detect mouse IgG with a detection limit of 1.0 pg/mL.     

Electrocatalytic Properties of a Gold Nanoseed Particle‐modified Indium Tin Oxide Electrode: Comparison of the Shape and Preparation Methods

Gold nanostructures are the most commonly used nanostructures for fabricating electrochemical sensors and biosensors. In this study, we compared the catalytic performances of three types of gold nanoseed particles having two different morphologies, upon attachment to an amino‐functionalized ITO electrode surface. The ITO electrode surface was modified with 3‐aminopropyltrimethoxysilane (APTMS) and (1) gold nanoseed spheres (AuNSS), prepared using the ion capture and successive reduction method (ICR), (2) commercially available 5 nm AuNSS, and (3) a newly synthesized gold nanoseed wire (AuNSW). The electrocatalytic properties of the three electrodes were evaluated. Among the three electrodes, the AuNSW/APTMS/ITO was found to be the electrode of choice and exhibited excellent electrocatalytic properties toward the biologically important analytes glucose, uric acid, and serotonin.     

Surface modification of indium tin oxide via electrochemical reduction of aryldiazonium cations

The facile deposition of para-substituted aryl films onto indium-tin oxide (ITO) electrodes by the electrochemical reduction of aryl diazonium salts in acetonitrile is reported. For the deposition conditions used in this report, the aryl film thicknesses are on the order of 1-6 nm, suggesting a multilayer structure. Regardless of the functional group on the aryl diazonium cation, (NO(2), CO(2)H, or fluorene) the electrodeposition behavior onto ITO electrodes is similar to that seen on other electrode materials. XPS and UV-vis data support the introduction of organic functional surface groups to ITO. The blocking behavior of the aryl films on ITO toward the Ru(NH(3))(6)(3+/2+) redox couple is in agreement with electron transfer through conjugated organic layers. The facile preparation of patterned aryl films with regular-spaced 700 nm voids on ITO is also described. Atomic force microscopy and scanning surface potential microscopy on patterned NO(2) aryl films are used to assess the molecular structure and orientation. A 100 mV decrease in the contact potential over NO(2) aryl films relative to bare ITO suggests that the aryl films are loosely structured as deposited with the NO(2) groups oriented at a small angle away from the ITO surface.     

Artificial photosynthesis by using chloroplasts from spinach adsorbed on a nanocrystalline TiO2 electrode for photovoltaic conversion

Photovoltaic conversion has been achieved by use of chloroplasts (photosynthetic organs) from spinach adsorbed on a nanocrystalline TiO₂ film on an indium tin oxide (ITO) glass electrode (chloroplast/TiO₂ electrode). The shape of the absorption spectrum of the chloroplast/TiO₂ electrode is almost the same that of a dispersion of the chloroplasts. Absorption maxima of the chloroplast/TiO₂ electrode observed at 430, 475, and 670 nm were attributed to carotenoid and chlorophyll molecules, suggesting that chloroplasts have been adsorbed by the nanocrystalline TiO₂ film on the ITO electrode. The photocurrent responses of chloroplast/TiO₂ electrodes were measured by using a solution of 0.1 M tetrabutylammonium hexafluorophosphate in acetonitrile as redox electrolyte in the presence or absence of water and 100 mW cm^?2 irradiation. The photocurrent of the chloroplast/TiO₂ electrode was increased by adding water to the redox electrolyte. The photocurrent responses of chloroplast/TiO₂ electrodes irradiated with monochromatic light (680 nm, the absorption band of photosystem II complexed with evolved oxygen) were measured by use of a solution of 0.1 M tetrabutylammonium hexafluorophosphate in acetonitrile as redox electrolyte in the presence or absence of water. A chloroplast/TiO₂ electrode photocurrent was observed only when the redox electrolyte containing water was used, indicating that the oxygen evolved from water by photosystem II in chloroplasts adsorbed by a nanocrystalline TiO₂ film on an ITO electrode irradiated at 680 nm is reduced to water by the catalytic activity of the platinum electrode. The maximum incident photon-to-current conversion efficiency (IPCE) was 0.8 % on irradiation at 670 nm.     

Preparation of Indium Tin Oxide Nanoparticle‐modified 3‐Aminopropyltrimethoxysilane‐functionalized Indium Tin Oxide Electrode for Electrochemical Sulfide Detection

A sulfide sensor based on an indium tin oxide nanoparticle (ITONP)‐modified ITO electrode was developed. To prepare ITONP‐modified ITO, various methods were tested. Drop‐drying of ITONPs (aq.) on aminopropyltrimethoxysilane‐functionalized ITO (APTMS/ITO) was found to be the best method on the basis of voltammetric analysis of the sulfide ion. ITONP‐modified APTMS/ITO (ITONP/APTMS/ITO) yielded much better electrocatalytic properties toward sulfide electro‐οxidation than did bare or APTMS/ITO electrodes. The ITONPs and ITONP‐modified ITO were also characterized using transmission electron microscopy and field emission scanning electron microscopy, respectively. Optimization of the type of inert electrolyte and pH yielded an ITONP/APTMS/ITO detector whose amperometrically and chronocoulοmetrically determined limits of detection for sulfide were 3.0 μM and 0.90 μM, respectively. ITONP/APTMS/ITO electrodes displayed reproducible performance, were highly stable, and were not susceptible to interference by common contaminants. Thus, the developed electrode can be considered as a promising tool for sensing sulfide.     

AC electrokinetic immobilization of influenza virus

The use of alternating current (AC) electrokinetic forces, like dielectrophoresis and AC electroosmosis, as a simple and fast method to immobilize sub-micrometer objects onto nanoelectrode arrays is presented. Due to its medical relevance, the influenza virus is chosen as a model organism. One of the outstanding features is that the immobilization of viral material to the electrodes can be achieved permanently, allowing subsequent handling independently from the electrical setup. Thus, by using merely electric fields, we demonstrate that the need of prior chemical surface modification could become obsolete. The accumulation of viral material over time is observed by fluorescence microscopy. The influences of side effects like electrothermal fluid flow, causing a fluid motion above the electrodes and causing an intensity gradient within the electrode array, are discussed. Due to the improved resolution by combining fluorescence microscopy with deconvolution, it is shown that the viral material is mainly drawn to the electrode edge and to a lesser extent to the electrode surface. Finally, areas of application for this functionalization technique are presented.     

In situ spectroelectrochemical behaviour of nanocrystalline TiO_2 thin films electrode fabricated by pulsed laser deposition

Nanocrystalline titanium oxide thin films have been successfully deposited on ITO coated glass by pulsed laser ablation of metallic Ti target in O_3/O_2 ambient gases. The intercalation of Li ions in the anatase TiO_2 film electrode is examined by cyclic vohammetry. The electrochromic behaviour of TiO_2 electrode is investigated by in-situ visible transmittance measurement, and two absorption bands at 420 and 650 nm are observed. The absorption falling and rising in color changing with excellent revisibility is relative to the insertion and deintercalation processes of Li ion. These resuits suggest that nanocrystalline titanium oxide films fabricated by pulsed laser deposition exhibit excellent spectroelectrochemical property.     

Dye‐Controlled Interfacial Electron Transfer for High‐Current Indium Tin Oxide Photocathodes

Efficient sensitized photocathodes are highly desired for solar fuels and tandem solar cells, yet the development is hindered by the scarcity of suitable p‐type semiconductors. The generation of high cathodic photocurrents by sensitizing a degenerate n‐type semiconductor (tin‐doped indium oxide; ITO) is reported. The sensitized mesoporous ITO electrodes deliver cathodic photocurrents of up to 5.96±0.19 mA cm^?2, which are close to the highest record in conventional p‐type sensitized photocathodes. This is realized by the rational selection of dyes with appropriate energy alignments with ITO. The energy level alignment between the highest occupied molecular orbital of the sensitizer and the conduction band of ITO is crucial for efficient hole injection. Transient absorption spectroscopy studies demonstrate that the cathodic photocurrent results from reduction of the photoexcited sensitizer by free electrons in ITO. Our results reveal a new perspective toward the selection of electrode materials for sensitized photocathodes.     

Effects of gold nanoparticle and electrode surface properties on electrocatalytic silver deposition for electrochemical DNA hybridization detection

In this paper we report the catalytic effects of various gold nanoparticles for silver electrodeposition on indium tin oxide (ITO)-based electrodes, and successfully apply this methodology for signal amplification of the hybridization assay. The most widely used gold nanoparticle-based hybridization indicators all promote silver electrodeposition on the bare ITO electrodes, with decreasing catalytic capability in order of 10 nm gold, DNA probe-10 nm gold conjugate, streptavidin-5 nm gold, and streptavidin-10 nm gold. Of greater importance, these electrocatalytic characteristics are affected by any surface modifications of the electrode surfaces. This is illustrated by coating the ITO with an electroconducting polymer, poly(2-aminobenzoic acid)(PABA), as well as avidin molecules, which are promising immobilization platforms for DNA biosensors. The catalytic silver electrodeposition of the gold nanoparticles on the PABA-coated ITO surfaces resembles that on the bare surfaces. With avidin covalently bound to the PABA, it is interesting to note that the changes in electrocatalytic performance vary for different types of gold nanoparticles. For the streptavidin-5 nm gold, the silver electrodeposition profile is unaffected by the presence of the avidin layer, whereas for both the 10 nm Au and DNA probe-10 nm gold conjugate, the deposition profiles are suppressed. The streptavidin-5 nm gold is employed as the hybridization indicator, with avidin-modified (via PABA) ITO electrode as the immobilization platform, to enable signal amplification by the silver electrodeposition process. Under the conditions, this detection strategy offers a signal-to-noise ratio of 20. We believe that this protocol has great potential for simple, reproducible, highly selective and sensitive DNA detection on fully integrated microdevices in clinical diagnostics and environmental monitoring applications.     

Polymer‐coated Boron Doped Diamond Optically Transparent Electrodes for Spectroelectrochemical Sensors

Spectroelectrochemical sensors combine electrochemistry, spectroscopy, and partitioning into a film to provide improved selectivity for the target analyte. The sensor usually consists of an optically transparent electrode (OTE) coated with a charge selective polymer film. The polymer film is chosen to pre‐concentrate analyte at the OTE surface to improve the sensitivity and provide selectivity against like charged interferences. OTEs such as Indium Tin Oxide (ITO) have been used extensively for spectroelectrochemical sensors, but little is known about the applicability of such sensors using other OTE materials, such as Boron Doped Diamond (BDD). One distinct advantage of BDD OTEs over ITO OTEs is their significant increase in sensitivity for organic compounds, such as 4‐aminophenol and hydroquinone. We have developed absorption and fluorescence‐based sensing methods with a BDD OTE coated with a sulfonated ionomer film, Nafion. This is demonstrated with tris(2,2′‐bipyridyl)ruthenium(II) ion [Ru(bpy)₃²⁺] using an attenuated total reflectance (ATR) flow cell setup for both absorption and fluorescence. With a Nafion coated BDD optically transparent thin layer electrode (OTTLE), we developed a fluorescence based sensor for a common polyaromatic hydrocarbon (PAH), 1‐hydroxypyrene (1‐pyOH), achieving a detection limit of 80 nM (17 ppb). This work manifests new sensing applications while broadening the use of spectroelectrochemistry, OTEs, and BDD as an electrode material.     

Enhanced electrothermal pumping with thin film resistive heaters

This work demonstrates the use of thin film heaters to enhance electrothermal pumping in microfluidic systems. Thin film heating electrothermal pumping is more efficient than Joule heating alone. Numerical simulations of an asymmetric electrode array are performed to demonstrate the advantages of incorporating thin film heaters. This specific simulation shows that thin film heater electrothermal pumping provides approximately two and one‐half times more volumetric flow than Joule heating alone for the same input power to both systems. In addition, external heating allows for electrothermal pumping to be applicable to low conductivity media.     

Assembly of long carbon nanotube bridges across transparent electrodes using novel thickness-controlled dielectrophoresis

The assembly of carbon nanotubes (CNTs) across planner electrodes using dielectrophoresis (DEP) is one of the standard methods used to fabricate CNT-based devices such as sensors. The medium drag velocity caused by electrokinetic phenomena such as electrothermal and electroosmotic might drive CNTs away from the deposition area. This problem becomes critical at large-scale electrode structures due to the high attenuation of the DEP force. Herein, we simulated and experimentally validated a novel DEP setup that uses a top glass cover to minimize the medium drag velocity. The simulation results showed that the drag velocity can be reduced by 2–3 orders of magnitude compared with the basic DEP setup. The simulation also showed that the optimum channel height to result in a significant drag velocity reduction was between 100 μm and 240 μm. We experimentally report, for the first time, the assembly and alignment of CNT bridges across indium tin oxide (ITO) electrodes with spacing up to 125 μm. We also derived an equation to optimize the CNT's concentration in suspensions based on the electrode gap width and channel height. The deposition of long CNTs across ITO electrodes has potential use in transparent electronics and microfluidic systems.     

Photovoltaic properties of self-assembled monolayers of porphyrins and porphyrin-fullerene dyads on ITO and gold surfaces

A systematic series of ITO electrodes modified chemically with self-assembled monolayers (SAMs) of porphyrins and porphyrin-fullerene dyads have been designed to provide valuable insight into the development of artificial photosynthetic devices. First the ITO and gold electrodes modified chemically with SAMs of porphyrins with a spacer of the same number of atoms were prepared to compare the effects of energy transfer (EN) quenching of the porphyrin excited singlet states by the two electrodes. Less EN quenching was observed on the ITO electrode as compared to the EN quenching on the corresponding gold electrode, leading to remarkable enhancement of the photocurrent generation (ca. 280 times) in the porphyrin SAMs on the ITO electrode in the presence of the triethanolamine (TEA) used as a sacrificial electron donor. The porphyrin (H(2)P) was then linked with C(60) which can act as an electron acceptor to construct H(2)P-C(60) SAMs on the ITO surface in the presence of hexyl viologen (HV(2+)) used as an electron carrier in a three electrode system, denoted as ITO/H(2)P-C(60)/HV(2+)/Pt. The quantum yield of the photocurrent generation of the ITO/H(2)P-C(60)/HV(2+)/Pt system (6.4%) is 30 times larger than that of the corresponding system without C(60): ITO/H(2)P-ref/HV(2+)/Pt (0.21%). Such enhancement of photocurrent generation in the porphyrin-fullerene dyad system is ascribed to an efficient photoinduced ET from the porphyrin singlet excited state to the C(60) moiety as indicated by the fluorescence lifetime measurements and also by time-resolved transient absorption studies on the ITO systems. The surface structures of H(2)P and H(2)P-C(60) SAMs on ITO (H(2)P/ITO and H(2)P-C(60)/ITO) have been observed successfully in molecular resolution with atomic force microscopy for the first time.     

Transparent graphene/PEDOT–PSS composite films as counter electrodes of dye-sensitized solar cells

Composite films of graphene and polystyreneslufonate doped poly(3,4-ethylenedioxythiophene) (graphene/PEDOT–PSS) were deposited on indium tin oxide (ITO) substrates by spin coating at room temperature and applied as counter electrodes of dye-sensitized solar cells (DSSCs). A 60 nm thick composite film (contained 1 wt% graphene) coated ITO electrode exhibited high transmittance (>80%) at visible wavelengths and high electrocatalytic activity. The energy conversion efficiency of the cell with this film as counter electrode reached 4.5%, which is comparable to 6.3% of the cell with platinum counter electrode under the same experimental condition.