Kinetic spectrophotometric determination of trace amounts of selenium and vanadium

A sensitive kinetic spectrophotometric method has been developed for the determination of Se(IV) over the range of 45 to 4000 ng in 10 mL of solution. The method is based on the catalytic effect of Se(IV) on the reduction reaction of bromate by hydrazinium dichloride, with subsequent reaction of Ponceau S with products of the above reaction (chlorine and bromine), causing color changing of Ponceau S. Method development includes optimization of time interval for measurement of slope, pH, reagents concentration, and temperature. The optimized conditions yielded a theoretical detection limit of 33 ng/¶10 mL of solution of Se(IV). The interfering effects were studied and removed. The method was applied to the determination of selenium in spiked water, Kjeldahl tablet, selenium tablet, and shampoo. Vanadium(V) has an inhibition effect on the catalyzed reaction of bromate and hydrazine by selenium. Using this effect, V(V) can be determined in the range of 70 to 2500 ng in 10 mL of solution. The optimization procedure includes pH and selenium concentration. An extraction method was used for interference removal. The method was applied to the determination of vanadium in petroleum.     

Kinetic-spectrophotometric determination of selenium in natural water after preconcentration of elemental selenium on activated carbon

A simple, accurate, sensitive and selective method is described for rapid determination of ultra-trace quantities of selenium. Selenium (IV) was collected on activated carbon after reduction to elemental Se by l-ascorbic acid. The collected selenium was then determined based on its accelerating effect on the oxidation reaction of methyl orange with bromate in acidic media. Total amount of Se(IV) and Se(VI) were collected on AC after their reduction by hydrazine. Se(IV), Se(VI) and total selenium could be determined by the method. Selenium in the range 10-10 000 ng could be determined by the method. The method was used to the determination of Se(IV), Se(VI) and total selenium in natural water with satisfactory results.     

溴酸钾-二甲酚橙体系-顺序注射-催化光度法测定痕量钒

在酸性介质条件下,钒(Ⅳ)能显著催化溴酸钾对二甲酚橙的氧化褪色反应。据此建立了测定痕量钒(Ⅳ)的顺序注射催化光度法。方法的线性范围为0.5~50ng/mL、检出限为0.4ng/mL。对10ng/mL的钒(Ⅳ)连续11次测定的相对标准偏差为1.1%。用于环境水样中痕量钒(Ⅳ)的测定,加标回收率为91%~108%。     

溴酸钾二甲酚橙体系-顺序注射-催化光度法测定痕量钒

在酸性介质条件下,钒(Ⅳ)能显著催化溴酸钾对二甲酚橙的氧化褪色反应。据此建立了测定痕量钒(Ⅳ)的顺序注射催化光度法。方法的线性范围为0.5⁵0ng/mL、检出限为0.4ng/mL。对10ng/mL的钒(Ⅳ)连续11次测定的相对标准偏差为1.1%。用于环境水样中痕量钒(Ⅳ)的测定,加标回收率为91%50ng/mL、检出限为0.4ng/mL。对10ng/mL的钒(Ⅳ)连续11次测定的相对标准偏差为1.1%。用于环境水样中痕量钒(Ⅳ)的测定,加标回收率为91%¹08%。     

Spectrophotometric determination of trace amounts of selenium with catalytic reduction of bromate by hydrazine in hydrochloric acid media

A method is presented for the determination of selenium, based on the catalytic effect of selenium(IV) on the reduction reaction of BrO(-)(3) by N(2)H(4).2HCl. The decolourization of Methyl Orange by the reaction products was used to monitor the reaction spectrophotometrically at 525 nm. This method is precise, highly sensitive, simple, rapid, widely applicable and selective for the determination of selenium(IV) and total selenium. The variables which affected the reaction rate were fully investigated and the optimum conditions were established. Selenium, as low as 1 ng/ml, can be determined by this method. The relative standard deviation of 20 ng of selenium was 0.94% (N = 10). The method was applied to the determination of Se(IV) in a health-care product.     

Catalytic spectrophotometric determination of vanadium in seawaters based on the bromate oxidative coupling reaction of metol and 2,3,4-trihydroxybenzoic acid.

A new, simple, sensitive and selective catalytic method is developed for the determination of vanadium in natural and sea waters. The method is based on the catalytic effect of V(V) and/or V(IV) on the bromate oxidative-coupling reaction of metol with 2,3,4-trihydroxybenzoic acid (THBA). The reaction is followed spectrophotometrically by tracing the oxidation product at 380 and/or 570 nm after 5 min of mixing the reagents. The optimum reaction conditions are 6.4 x 10(-3) mol l-1 of metol, 2.0 x 10(-3) mol l-1 of THBA and 0.16 mol l-1 of bromate at 35 degrees C and in the presence of an activator-buffer solution of 1 x 10(-2) mol l-1 of tartrate (pH = 3.10). Following the recommended procedure, V(V) and/or V(IV) can be determined with linear calibration graphs up to 0.75 ng ml-1 and detection limits, based on the 3Sb criterion, of 0.008 and 0.018 ng ml-1 at 380 and 570 nm, respectively. The developed method was successfully applied, without any separation or preconcentration processes, to the determination of vanadium in natural and seawaters following the direct calibration and standard addition techniques, respectively.     

Speciation analysis of selenium in natural water using square-wave voltammetry after preconcentration on activated carbon

A simple, accurate, sensitive and selective method was described for rapid determination of ultra-trace quantities of selenium. Selenium(IV) was collected on activated carbon (AC) after reduction to elemental Se by l-ascorbic acid. The collected selenium was then dissolved by oxidation reaction with bromate in acidic media and was indirectly determined through the bromide formation using square-wave voltammetry (OSWV). The total amount of Se(IV) and Se(VI) was collected on AC after its reduction by hydrazine. Selenium in the range 0.01-20 μg L⁻¹ could be determined by this method. The method was used to the determination of Se(IV) and Se(VI) in natural water with satisfactory results.     

Spectrophotometric catalytic determination of ultra-trace amounts of selenium based on the reduction of resazurin by sulphide

A sensitive catalytic method for determining ng ml^? concentration of selenium is described. The method is based on the catalytic action of Se(IV) on the reduction of resazurin by sulphide, monitored spectrophotometrically at 605 nm. The linearity range of the calibration graph is dependent on the concentration of sulphide. The variables affecting the rate of the reaction were investigated and the optimum conditions were established. The method is simple, rapid, precise, sensitive and widely applicable. As low as 8.0 × 10^?4 μg ml^?1 of selenium can be determined. The relative standard deviation of seven determination of 10 ng Se was 0.7%. The determination of Se(IV) in the presence of Se(VI) and the determination of total selenium are also described.     

Catalytic Spectrophotometric Determination of Nanogram Amounts of Selenium(IV)

A method is proposed for the catalytic spectrophotometric determination of nanogram amounts of selenium(IV). The method is based on the reduction of nitrate with iron(II) ethylenediaminetetraacetate catalyzed by Se(IV) compounds. The reaction proceeds in several stages and yields iron(III) ethylenediaminetetraacetate, the nitrosyl complex of iron, nitrous acid, and other products. Nitrous acid enters into the diazotization reaction with aromatic amine. The resulting diazo compound is coupled with another aromatic amine to form the azo compound. 4-Nitroaniline is used as the diazo component, and N-diethyl-N-(1-naphthyl)ethylenediamine is used as the azo component. The molar absorptivity of the solution of the azo compound is 4.5 × 10⁴ at 540 nm. A kinetic method was developed for the determination of selenium(IV) in potable and natural waters with the use of the standard addition method. The detection limit of selenium by the proposed method is 0.1 ng/mL. In the determination of 0.2 and 2 ng/mL selenium, the relative standard deviation is 6 and 2%, respectively. The interfering effect of organic compounds dissolved in natural water is eliminated by the ultrasonic treatment of water samples.     

Spectrofluorimetric kinetic determination of selenium (IV) by flow injection analysis in cationic micellar medium

A sensitive catalytic kinetic spectrofluorimetric method for determining ng ml(-1) of selenium by flow injection analysis has been developed. The method, based on the catalytic effect of Se (IV) on the reduction of resorufin by sulphide, in the presence of cetylpyridinium chloride, is monitored spectrofluorimetrically (lambda(ex)=480 nm; lambda(em)=583 nm). The linearity range of the calibration graph is dependent on the concentration of sulphide. The variables affecting the rate of the reaction were investigated. The method is simple, rapid, precise, sensitive, and widely applicable. The limit of detection is 1 ng ml(-1) Se (IV), and the calibration range is 5-1000 ng ml(-1). Sampling rate is 60 samples h(-1), and the relative standard deviation of 12 determinations of 100 ng ml(-1) Se was 0.76%. The determination of Se (IV) in the presence of Se (VI) and total selenium is described. The method was applied to the determination of Se in selenium tablets, and several synthetic samples.     

Cloud point extraction combined with electrothermal vaporization inductively coupled plasma mass spectrometry for the speciation of inorganic selenium in environmental water samples

A new method based on cloud point extraction (CPE) separation and electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICPMS) detection has been proposed for the speciation of inorganic selenium in environmental waters. When the temperature of the system is higher than the cloud point temperature (CPT) of the selected surfactant Triton X-114, the complex of Se(IV) with ammonium pyrrolidine dithiocarbamate (APDC) seems to be extracted into the surfactant-rich phase, whereas the Se(VI) remains in aqueous solutions. Thus, an in situ separation of Se(IV) and Se(VI) could be realized. The concentrated analyte was introduced into the ETV-ICP mass spectrometer for determination of Se((IV) after dilution with 200 microL methanol. Se(VI) was reduced to Se(IV) prior to determining total selenium, and its assay was based on subtracting Se(IV) from total selenium. The main factors affecting the CPE and the vaporization behavior of the analyte were investigated in detail. Under the optimized experimental conditions, the limit of detection (LOD) for Se(IV) was 8.0 ng/L with an enhancement factor of 39 when 10 mL of sample solution was preconcentrated to 0.2 mL. The relative standard deviation (RSD) was found to be 3.9% (C(Se(IV)) = 1.0 microg/L, n = 7). The proposed method was applied to the speciation of inorganic selenium in different environmental water samples with the recovery for the spiked samples in the range of 82-102%.     

Kinetic determination of selenium using the reduction of nile blue with sulfide ions

The catalytic effect of Se(IV) was first observed in the reaction of the reduction of Nile Blue with sulfide ions. Optimal conditions for the determination of selenium by this reaction were found. The dependence of the reaction rate on the concentration of Se(IV) was linear in the concentration range 0.008-0.16 μg/mL. Solvent extraction with dithiophosphoric acids was proposed for the separation of selenium from the interferents. A procedure for the extraction-kinetic determination of selenium with the detection limit 0.006 μg/mL was developed.     

Determination Of SE(IV) in the Presence of SE(VI) at NG ML− Concentration Levels by a Kinetic Spectrophotometric Method

ABSTRACT

The catalytic effect of Se(IV) on the reduction reaction of thionine(TN) by sulfide ion is used for determination of trace amounts of selenium(IV) ion by a kinetic-spectrophotometric method. This new method is simple and highly sensitive. The reaction was monitored spectrophotometrically by measuring the decrease in absorbance of the reaction mixture at 598 nm. The fixed time method was used for the first 45s from initiation of the reaction. Under the optimum conditions, in the concentration range of 2-90 ng ml^? of selenium(IV), a quite linear regression equation (r = 0.9984, n = 14) was obtained. The experimental detection limit of the method (S/N = 3) was 1.3 ng ml^?. The relative standard deviation of ten replicate measurements is 2.51% for a 40 ng ml^? solution of selenium. The proposed method is used to the study of selenium (IV,VI) speciation in water at ng ml^? levels. This method was extended for the determination of selenium in real samples.     

Speciation of selenite and selenate using living bacteria

In this work, a reliable method is described for speciation of soluble inorganic selenium ions, Se(IV) and Se(VI), which combines an uptake process by using living bacterial cells and electrothermal atomic absorption spectrometry (ETAAS). A selective retention of either Se(IV) or Se(IV) plus Se(VI) can be carried out by using the uptake system made up of either Pseudomonas putida or Escherichia coli strains cultivated in a culture medium based on glucose (P. putida) and glucose plus dipotassium phosphate (E. coli) mixed together with the original sample solution containing the selenium species. Discrimination between inorganic selenium species is possible by combining the optimization of the bacterial cell, the growth conditions and the relative rates of their retention from the sample. In the general procedure, an equilibrium between the analyte in the solution and the uptake system is allowed to be established, and then the concentration of selenium is determined directly in the biomass by slurry sampling ETAAS. Nonetheless, a theoretical model is proposed to describe the retention process by the living bacterial cells, which also provides a feasible quantification of the extraction process before the adsorption equilibrium is reached and whenever the agitation conditions and the sampling time are under control. The detection limits for the inorganic selenium species at the best retention conditions are of 5.7 ng Se(IV) ml(-1) for P. putida and 6.1 ng Se(IV) ml(-1) and 6.3 ng Se(VI) ml(-1) for E. coli. The relative standard deviations of the adsorption/determination process are 2.9-6.3%.     

Catalytic polarographic determination of total selenium in tea leaves

The catalytic polarographic determination of selenium(IV) by use of the SeSO(2-)(3) -KIO(3) system is sensitive, accurate, rapid and requires only small quantities of sample. The detection limit for selenium(IV) is 0.04 ng/ml in the final solution. The working range of the calibration is 0.04-2.5 ng/ml. Se(VI) present can be reduced with hot hydrochloric acid to Se(IV), allowing determination of the total selenium.     

Kinetic spectrophotometric method for the determination of selenium(IV) by its catalytic effect on the reduction of spadns by sulphide in micellar media

A simple kinetic spectrophotometric method was developed for the determination of ultratrace amounts of Se(IV). The method is based on the reduction of spadns by sulphide in micellar media. The reaction was monitored spectrophotometrically by measuring the decrease in the absorbance of spadns at 515 nm with a fixed-time method. The decrease in the absorbance of spadns is proportional to the concentration of Se(IV) in the range 0.5–100 ng/mL with a fixed time of 2.5–7.0 min from the initiation of the reaction. The limit of detection is 0.3 ng/mL Se(IV). The relative standard deviation for the determination of 0.02 and 0.10 μg/mL Se(IV) was 2.10 and 1.95%, respectively. The method was applied to the determination of Se(IV) in water. The text was submitted by the authors in English.     

Determination of trace titanium with titanium(IV)-(DBC-arsenazo)-potassium bromate system by catalytic-kinetic spectrophotometry

In a 0.080 M sulphuric acid medium, trace titanium(IV) catalyzes the discoloring reaction of DBC-arsenazo oxidized by potassium bromate and the discoloring degree is proportional to the concentration of titanium(IV) in the solution. A new catalytic-kinetic spectrophotometric method for the determination of trace titanium(IV) was developed based on this principle. At a wavelength of 516 nm, the linear range of determination of titanium(IV) is 0–2.2 μg/25 mL. The detection limit for the determination of titanium is 2.04 ng/mL. The present method has been satisfactorily applied to the determination of titanium in fish samples. The text was submitted by the authors in English.     

Reaction of 2,3-Dimethylmercaptopropionic Acid with Methylene Blue as an Indicator Reaction for the Kinetic Determination of Selenium

A new indicator reaction between 2,3-dimethylmercaptopropionic acid and Methyl Blue was proposed for the kinetic determination of selenium. The optimal reaction conditions were found. A linear relationship was observed between the induction period and the Se(IV) concentration in the range between 0.9 and 9.6 ng/mL Se. Masking with EDTA and solvent extraction with diethyldithiophosphoric acid can be used for the separation of interfering elements forming complexes with the reagent.     

Kinetic spectrophotometric determination of trace amounts of selenium based on the catalytic reduction of maxilon blue-SG by sulfide

A simple and sensitive catalytic spectrophotometric method was developed for the determination of trace amounts of selenium. The method is based on the catalytic effect of selenium in form Se(IV) on the reduction of Maxilon Blue-SG by sodium sulfide. Indicator reaction is followed spectrophotometrically by measuring the absorbance change at λ_max=654 nm and constant temperature (30.0±0.1 °C) by fixed time method. Selenium could quantitatively be determined in the range 0.004-0.200 μg ml⁻¹ Se(IV) with a detection limit of 0.205 ng ml⁻¹ Se(IV). All of the variables that affected the reaction rate were investigated and established optimum conditions to give maximum sensitivity. The R.S.D.s of the method (N=12) for the Se(IV) concentrations of 0.004, 0.016, 0.040 and 0.160 μg ml⁻¹ are between 2.27 and 0.32%, respectively, and depended on Se(IV) concentration. The interference effect of various anion and cations on the Se(IV) determination was also fully studied. The selectivity of catalytic reaction was greatly improved with the use of the strong cation exchange resin. The developed kinetic-catalytic reaction was applied to the determination of selenium in real samples as Antioxidant-S, Selsun (which is a healthcare product for the treatment of dandruff) and analytical grade sodium metabisulfite, and in spring water samples without any pre-concentration. The acceptable recoveries were obtained by the method for appropriate standard Se(IV) additions. The method is simple, practical and suitable for using in small laboratories owing to its precision, sensitivity and relative selectivity.     

Preconcentration of inorganic selenium species (Se (IV) and Se (VI)) in an alumina filled microcolumn and on-line determination by hydride generation atomic absorption spectrometry

A flow injection system has been developed consisting of on-line preconcentration of selenium species in a microcolumn filled with activated alumina, reduction of Se(VI) to Se(IV) and determination by HG-AAS. When 0.01 mol/L HNO₃ is used both as carrier and activation reagent for the alumina microcolumn, up to 150 ng of Se(IV) and Se(VI) can be preconcentrated and quantitatively eluted by 500 L of 2 mol/L NH₃. The preconcentration factor is 50 when 25 mL of sample is used. The detection limit is about 6 ng/L, the precision is 5% for low concentrations such as 150 ng/L and 3% at high concentrations such as 120 ng/mL. The proposed method is suitable for natural water samples and inorganic Se speciation can be performed by determining Se(IV) and total selenium [Se(VI) is evaluated from the difference].