Detection of propranolol in pharmaceutical formulations by diffuse reflectance spectroscopy

This paper describes an analytical reflectometric method that has an objective not only the industrial quality control but also to detect possible falsifications and/or adulterations of propranolol in pharmaceutical formulations. The method is based on the diffuse reflectance measurements of the colored product (III) of the spot test reaction between propranolol hydrochloride (I) and 2,6-dichloroquinone-4-chloroimide (II) using filter paper as solid support. Spot test conditions have been investigated using experimental design in order to identify and optimize the critical factors. The factors evaluated were DCQ concentration, propranolol solvent and DCQ solvent. The best reaction conditions were achieved with the addition of 30 microL of propranolol solution in ethanol 35% (v/v) and 30 microL of DCQ solution at 70 mg mL(-1) in acetone, in this order. All reflectance measurements were carried out at 500 nm and the linear range was from 8.45x10(-4) to 8.45x10(-2)mol L(-1) (r=0.998). The limit of detection was 1.01x10(-4)mol L(-1). No interference was observed from the assessed excipients and drugs. The method was applied to determine propranolol in commercial brands of pharmaceuticals. The results obtained by the proposed method were favorably compared with those given by the British Pharmacopoeia procedure.     

Simultaneous square-wave voltammetric determination of aspartame and cyclamate using a boron-doped diamond electrode

A simple and highly selective electrochemical method was developed for the simultaneous determination of aspartame and cyclamate in dietary products at a boron-doped diamond (BDD) electrode. In square-wave voltammetric (SWV) measurements, the BDD electrode was able to separate the oxidation peak potentials of aspartame and cyclamate present in binary mixtures by about 400 mV. The detection limit for aspartame in the presence of 3.0x10(-4) mol L(-1) cyclamate was 4.7x10(-7) mol L(-1), and the detection limit for cyclamate in the presence of 1.0x10(-4) mol L(-1) aspartame was 4.2x10(-6) mol L(-1). When simultaneously changing the concentration of both aspartame and cyclamate in a 0.5 mol L(-1) sulfuric acid solution, the corresponding detection limits were 3.5x10(-7) and 4.5x10(-6) mol L(-1), respectively. The relative standard deviation (R.S.D.) obtained was 1.3% for the 1.0x10(-4) mol L(-1) aspartame solution (n=5) and 1.1% for the 3.0x10(-3) mol L(-1) cyclamate solution. The proposed method was successfully applied in the determination of aspartame in several dietary products with results similar to those obtained using an HPLC method at 95% confidence level.     

Flow Injection Analysis of Histidine with Enhanced Electrogenerated Chemiluminescence of Luminol

Histidine is one of the necessary basic amino acids in biological bases, which often controls the catalytic activity of enzymes and acts in holding the higher structure of proteins. Furthermore, it is also an important ingredient in pharmaceutical preparations used for treatment of hetpatosis and nephropathy. Therefore, the determination of histidine in biological fluids and pharmaceutical preparations is of great importance. Various methods have been proposed for the detection of histidine …     

Sensitive flow-injection amperometric detection of iodide using Mn3+ and As3+.

A rapid, selective, and sensitive kinetic flow-injection method for iodide content determination with amperometric detection on a platinum electrode was developed. The method is based on the catalytic effect of iodide on the Mn3+ reaction with As3+ in the presence of sulfuric acid. The calibration curve was linear in the concentration range from 5.0 x 10(-7) to 1.0 x 10(-4) mol/L iodide. The limit of detection (LOD) was found to be 5.0 x 10(-9) mol/L iodide. The relative standard deviations (RSD) were 1.68% and 3.03% for 1.0 x 10(-3) mol/L standard and 1.0 x 10(-6) mol/L iodide solution (n = 6), respectively. The method has been successfully applied for determination of iodide in waters, table salts, fodder, organic substances and human blood sera. The results were compared with those obtained by a standard AOAC (Association of Official Analytical Chemists) method, as well as with those obtained by a kinetic spectrophotometric procedure for determination of iodide.     

Study on the electrochemical behavior and differential pulse voltammetric determination of rhein using a nanoparticle composite film-modified electrode

A sensitive electrochemical method was developed for the differential pulse voltammetric determination of rhein at a glassy carbon electrode (GCE) modified with a nanoparticle composite film. In the present paper, multi-wall carbon nanotube (MWNT) was dispersed into dihexadecyl phosphate (DHP) to give a homogeneous suspension. After the solvent evaporation, a uniform film of MWNT-DHP composite film was obtained on the GCE surface. The MWNT-DHP composite film-modified GCE exhibited excellent electrocatalytic behavior toward the redox of rhein. Compared with an irreversible reduction of rhein at the bare GCE, a reversible redox behavior of rhein was observed at the MWNT-DHP composite film-modified GCE and the redox current was also enhanced greatly. Based on this, a cathodic differential pulse voltammetry (DPV) was applied for the determination of rhein. The experimental parameters, which influence the current of rhein, were optimized. Under optimal conditions, the cathodic DPV measurements were performed and a linear response of rhein was obtained in the range from 1.0 x 10(-8) to 5.0 x 10(-6) mol L(-1) and with a limit of detect (LOD) of 5.0 x 10(-9) mol L(-1). The proposed procedure was successfully applied to assay rhein in real samples with satisfactory results.     

High selective determination iron(II) by its enhancement effect on the fluorescence of pyrene-tetramethylpiperidinyl (TEMPO) as a spin fluorescence probe

A novel fluorescence method determination for iron(II) with a high selectivity and sensitivity has been proposed, based on the enhancement of fluorescence signals resulting from specific redox reaction between synthesized spin fluorescence probe pyrene-tetramethylpiperidinyl (TEMPO) and iron(II). Under the experimental conditions, fluorescent probe displayed a rapid and linear response for iron(II) over the concentration range from 2.4 x 10(-7) to 3.6 x 10(-6) mol/L. The limit of detection was 4.0 x 10(-8) mol/L. The relative standard deviation of six replicate measurements was 1.90% for 3.0 x 10(-7) mol/L iron(II). Because of the specific redox reaction between developed spin fluorescence probe and iron(II), there are few interference by other ions, especially in the presence of relative high concentration iron(III). The method has been successfully applied for iron(II) determinations in two different kinds of real samples. Results determined by the proposed method agree favorably with those determined UV-vis spectrometry method with 1,10-phenanthroline.     

Kinetic spectrophotometric method for the determination of ranitidine and nizatidine in pharmaceuticals

An accurate and simple kinetic method is described for the determination of ranitidine and nizatidine in pure form and in pharmaceuticals. The method is based on the reaction of the compounds with 7-chloro-4-nitrobenz-2-oxa-1,3-diazole in pH 7.4 borate buffer at 60 degrees C for a fixed time of 25 min for both compounds. The absorbance of the reaction product is measured at 495 nm for ranitidine and nizatidine. Calibration graphs were linear over the concentration range of 2-20 microg/mL, with limits of detection of 0.13 (3.7 x 10(-7) M) and 0.25 microg/mL (7.5 x 10(-7) M) for ranitidine and nizatidine, respectively. The proposed method was applied successfully to the determination of ranitidine in tablets and ampoules with average recoveries of 100.26+/-0.69 and 100.29+/-0.59%, respectively, and to the determination of nizatidine in capsules with an average recovery of 104.26+/-0.44%. The results obtained are in good agreement with those obtained by the other methods used for comparison. A proposal of the reaction pathway is also presented.     

Determination of carbamazepine by chemiluminescence detection using chemically prepared tris(2,2'-bipyridine)ruthenium(III) as oxidant.

A new chemiluminescence method for the determination of carbamazepine (CBZ) has been developed. The method is based on the chemiluminescence produced in the reaction of tris(2,2'-bipyridine)ruthenium(III) and CBZ in an acidic medium. The chemiluminescence intensity was enhanced by organic solvents in the reaction system. Under the optimum experimental conditions, the calibration curve was linear over the range 4.0 x 10(-3)-8.6 x 10(-7) mol/L for CBZ. The detection limit (S/N = 3) was 2.5 x 10(-7) mol/L and the relative standard deviation of six replicate measurements was 2.6% for 4.0 x 10(-4) mol/L of CBZ. The possible reaction mechanism were also discussed. The chemiluminescence method was successfully applied to assay the CBZ contents in pharmaceutical tablets.     

Chemiluminescence flow injection analysis of 1,3-dichloro-5,5-dimethylhydantoin in swimming pool water

A new chemiluminescence (CL) flow-injection method is proposed for the determination of 1,3-dichloro-5,5-dimethylhydantoin (DDH). The method is based on the chemiluminescent reaction of DDH and luminol-H(2)O(2) in an alkaline medium (pH 12.0-12.5). The concentration of the analyte shows a good linear relationship with the produced luminescence intensity in the range of 3.0x10(-8) to 8.0x10(-6) mol l(-1). The detection limit of the proposed method is 1.0x10(-8) mol l(-1) and the relative standard deviation (R.S.D.) is 4.7% (n=5) at 5.0x10(-7) mol l(-1). This method was successfully applied to the determination of trace amounts of this disinfectant in water samples obtained from five different swimming pools. Satisfying recovery values were also obtained.     

Oil-in-water emulsions as suitable working media for the direct polarographic determination of aziprotryne and desmetryne from its organic extracts in water samples

The electroanalytical behavior of the reduction of the herbicides aziprotryne (2-azido-4-isopropylamino-6-methylthio-1,3,5-triazine) and desmetryne (4-isopropylamino-6-methylamino-2-methylthio-1,3,5-triazine) in oil-in-water emulsions is reported. This medium allows the differential pulse polarographic determination of these s-triazines directly from their sample extracts in an appropriate organic solvent. Sodium pentanesulfonate was chosen as the most suitable surfactant to be used as emulsifying agent, whereas ethyl acetate was selected as the organic solvent to form the emulsions. The peak current was maximum in a 0.3 mol L(-1) HClO4 medium of the continuous aqueous phase for aziprotryne, and at pH 3.0 for desmetryne, and the potential became more negative as the pH increased for both herbicides. The limiting current is diffusion controlled and the electrode process is irreversible. Four electrons are involved in the overall electrochemical reduction process as determined by controlled potential coulometry, whereas the alpha n(a) values suggested that two electrons are involved in the rate-determining step. Using differential pulse polarography, aziprotryne and desmetryne can be determined in the emulsified medium over the concentration ranges 1.0 x 10(-7)-1.0 x 10(-4) mol L(-1), with limits of detection of 4.5 x 10(-8) mol L(-1) and 6.6 x 10(-8) mol L(-1), respectively. The method was applied to the determination of aziprotryne and desmetryne in spiked irrigation water. At concentration levels of 6.0 x 10(-7) mol L(-1) aziprotryne and 4.0 x 10(-7) mol L(-1) desmetryne, recoveries of 94 +/- 3% and 94 +/- 4%, respectively, were obtained after preconcentration on Sep-Pack C18 cartridges. Finally, partial least-squares regression (PLSR) has been used for treatment of the polarographic data obtained from mixtures of aziprotryne, desmetryne and simazine in oil-in-water emulsions. The size of the calibration set was of 29 samples by ninety two current measurements at different potentials. Prediction of the herbicides concentration within the range 1.0 x 10(-6)-1.0 x 10(-5) mol L(-1) was possible.     

Direct determination of amino acids by pressurized capillary electrochromatography with chemiluminescence detection

A pressurized CEC (pCEC) coupled with on-column chemiluminescence (CL) detection was developed for direct determination of amino acids, which was based on the principle of an enhanced effect of Cu(II)-amino acid complexes on the CL reaction between luminol and hydrogen peroxide in alkaline solution. The effects of some important factors on pCEC separation and CL intensity were systemically investigated. Baseline separation of amino acids including L-histidine (L-His), L-threonine (L-Thr), and L-tyrosine (L-Tyr) was achieved by using a monolithic column with a mobile phase of 5.0x10(-3) mol/L phosphate buffer at pH 8.0 that contained 25% v/v methanol and 5.0x10(-4) mol/L luminol and 1.0x10(-5) mol/L Cu(II) at an applied voltage of -5 kV. The calibration curves of the analytes by plotting the peak height against corresponding concentration were linear over the range of 3.2x10(-6)-3.2x10(-4) mol/L for L-His, 4.1x10(-6)-4.1x10(-4) mol/L for L-Thr, and 6.0x10(-7)-3.0x10(-4) mol/L for L-Tyr. The LODs for L-His, L-Thr, and L-Tyr were 6.4x10(-7), 8.4x10(-7), and 3.0x10(-7) mol/L (S/N = 2), respectively. The proposed method was applied to the analysis of amino acid injection sample with satisfactory results. Mean recoveries for three amino acids were from 84.3 to 89.6%.     

Determination of a cationic surfactant with naphthalene black 12B by the resonance light scattering technique

A new determination method for a cationic surfactant, zephiramine (Zeph), was developed with resonance light scattering (RLS) technique, based on the interaction of naphthalene black 12B with Zeph. The resonance light scattering (RLS) and UV characteristics of interaction between naphthalene black 12B and Zeph were studied. The RLS intensity of naphthalene black 12B at 363 nm was greatly enhanced in the presence of Zeph at pH 6.0. The enhanced RLS is proportional to the concentration of Zeph in the range of 3.20 x 10(-7) - 1.44 x 10(-5) mol L(-1). The limit of detection was 8.8 x 10(-8) mol L(-1). The proposed method was applied to the determination of Zeph in synthetic and spiked water samples with the recovery of 96.2-104% and RSD of 1.1-2.5%.     

Simultaneous determination of dapsone and pyrimethamine by derivative spectrophotometry in pharmaceutical formulations

A simple and fast method was developed for the simultaneous determination of dapsone and pyrimethamine by first-order digital derivative spectrophotometry. Acetonitrile was used as a solvent to extract the drugs from the pharmaceutical formulations, and the samples were subsequently evaluated directly by digital derivative spectrophotometry. The simultaneous determination of both drugs was performed by the zero-crossing method at 249.4 and 231.4 nm for dapsone and pyrimethamine, respectively. The best signal-to-noise ratio was obtained when the first derivative of the spectrum was used. The linear range of determination for the drugs was from 6.6 x 10(-7) to 2.0 x 10(-4) and from 2.5 x 10(-6) to 2.0 x 10(-4) mol/L for dapsone and pyrimethamine, respectively. The excipients of commercial pharmaceutical formulations did not interfere in the analysis. Chemical and spectral variables were optimized for determination of both analytes. A good level of repeatability, 0.6 and 1.7% for dapsone and pyrimethamine, respectively, was observed. The proposed method was applied for the simultaneous determination of both drugs in pharmaceutical formulations.     

Sensitive determination of norepinephrine, synephrine, and isoproterenol by capillary electrophoresis with indirect electrochemiluminescence detection

A new and sensitive method for the determination of norepinephrine (NE), synephrine, and isoproterenol was developed by CE separation and indirect electrochemiluminescence detection (ECL) based on their quenching effects on the tris(2,2'-bipyridyl)-ruthenium(II)/tripropylamine (TPA) system. The conditions for CE separation and ECL detection were investigated in detail. Under the optimum conditions, the three analytes were well separated within 9 min. The LODs (S/N = 3) in standard solution are 2.6 x 10(-8) mol/L for NE, 6.6 x 10(-9) mol/L for synephrine and 8.4 x 10(-8) mol/L for isoproterenol, respectively. The precisions of intraday and interday are less than 4.4 and 6.1%, respectively. The LOQs (S/N = 10) in real human urine samples are 2.6 x 10(-7) mol/L for NE, 8.8 x 10(-8 ) mol/L for synephrine, and 8.8 x 10(-7) mol/L for isoproterenol, respectively. The applicability of the proposed method was illustrated in the determination of 20 human urine samples from diabetic patients and healthy persons. The results obtained indicated that the level of NE in patients (mean value 0.41 micromol/L) was higher than that in healthy persons (mean value 0.24 micromol/L).     

Electrochemiluminescent determination of L-cysteine with a flow-injection analysis system.

A flow-injection electrochemiluminescent method for L-cysteine determination has been developed based on its enhancement of the electrochemiluminecence of luminol at a glassy carbon electrode. This method is simple and sensitive for cysteine determination. Under the selected experimental parameters, the linear range for cysteine concentration was 1.0 x 10(-6) - 5.0 x 10(-5) mol/l, and the detection limit was 0.67 micromol/l (S/N = 3). The relative standard deviation for 11 measurements of 1.0 x 10(-5) mol/l cysteine was 4.5%. The proposed method has been applied to the detection of cysteine in pharmaceutical injections with satisfactory results.     

Simultaneous determination of estradiol and medroxyprogesterone acetate in pharmaceutical formulations by second-derivative spectrophotometry

This paper reports a simple and fast method for the simultaneous determination of estradiol (ED) and medroxyprogesterone acetate (MP) in pharmaceutical formulations by second-derivative spectrophotometry. Methanol was used to extract the drugs from formulations, and subsequently the extracts were evaluated directly by derivative spectrophotometry. The drugs were determined simultaneously by using the graphic method at 297.4 nm for ED and the zero-crossing method at 273.4 nm for MP. If both compounds are present together in a sample, it is possible to quantitate one in the presence of the other. The best signal-to-noise ratio was found when the second derivative of the spectrum was used. The linear ranges for determination of the drugs were 4.7 x 10(-6) to 1.6 x 10(-4) and 7.2 x 10(-6) to 2.0 x 10(-4) mol/L for ED and MP, respectively. The ingredients commonly found in commercial pharmaceutical formulations do not interfere with the determination. Chemical and spectral variables were optimized for the determination of both analytes. Good levels of repeatability (relative standard deviation), 1.4 and 1.9%, were obtained for ED and MP, respectively. The proposed method was applied to the determination of these drugs in pharmaceutical formulations.     

Construction and analytical application of a biosensor based on stearic acid-graphite powder modified with sweet potato tissue in organic solvents

A biosensor based on stearic acid-graphite powder modified with sweet potato (Ipomoea batatas (L.) Lam.) tissue as peroxidase source was constructed and applied in organic solvents. Several parameters were studied to evaluate the performance of this biosensor such as stearic acid-graphite powder and tissue composition, type and concentration of supporting electrolyte, organic solvents, water/organic solvent ratio (% v/v) and hydrogen peroxide concentration. After selection of the best conditions, the biosensor was applied for the determination of hydroquinone in cosmetic creams in methanol. At the peroxidase electrode hydroquinone is oxidized in the presence of hydrogen peroxide and the radical formed was reduced back electrochemically at -180 mV vs Ag/AgCl (3.0 mol L(-1) KCl). The reduction current obtained was proportional to the concentration of hydroquinone from 6.2 x 10(-5) to 1.5 x 10(-3) mol L(-1) (r = 0.9990) with a detection limit of 8.5 x 10(-6) mol L(-1). The recovery of hydroquinone from two samples ranged from 98.8 to 104.1% and an RSD lower than 1.0% for a solution containing 7.3 x 10(-4) mol L(-1) hydroquinone and 1.0 x 10(-3) mol L(-1) hydrogen peroxide in 0.10 mol L(-1) tetrabutylammonium bromide methanol-phosphate buffer solution (95:5% v/v) (n = 10) was obtained.     

Flow injection turbidimetric determination of thiamine in pharmaceutical formulations using silicotungstic acid as precipitant reagent

A simple flow injection system is proposed for the determination of thiamine in pharmaceutical formulations. The determination is based on the precipitation reaction of thiamine with silicotungstic acid in acidic medium to form a thiamine silicotungstate suspension that is measured at 420 nm. Adding 0.05% (w/v) poly(ethyleneglycol) in the carrier solution (0.5 mol l(-1) hydrochloric acid), an improvement in the sensitivity, repeatability and baseline stability of the flow injection system was obtained. The calibration graph was linear in the thiamine concentration range from 5.0x10(-5) to 3.0x10(-4) mol l(-1) with a detection limit of 1.0x10(-5) mol l(-1). The relative standard deviations for ten successive measurements of 1.0x10(-4) mol l(-1) and 2.5x10(-4) mol l(-1) thiamine were less than 1% and an analytical frequency of 90 h(-1) was obtained.     

Quantitative measurements of ammonium, hydrogenophosphate and Cu(II) by diffuse reflectance spectrometry

Diffuse reflectance spectrometry is shown to be useful for the quantitative determination of small amounts of pollutants. The relation between sample concentration and reflectance is described by the Kubelka-Munk equation. The experiments were performed with a laboratory constructed diode array spectrophotometer. We can obtain the quantitative reflectance values of different precipitates like ammonium with Nessler's reagent, hydrogenophosphate with silver nitrate and a complex such as Cu(II) with dithiooxamide 'rubeanic acid' by forming a spot colour on filter paper. We have obtained for each reagent a calibration curve by plotting the relative intensity of reflectance versus the log of the mol (dm(3))(-1) concentration. The linearity was obtained for Cu(II) from 8x10(-4) to 2.5x10(-2) mol l(-1) with r(2)=0.9838 and from 10(-3) to 10(-1) mol l(-1) for polyphosphate with r(2)=0.9975 and from 5x10(-4) to 5x10(-2) mol l(-1) for ammonium with r(2)=0.9889. We can consider that for a direct measurement of the intensity of reflectance, it is possible to perform quantitative spot-test analysis.     

N-溴代琥珀酰亚胺-二氯荧光素化学发光体系测定废水中5-磺基水杨酸

建立了测定5-磺基水杨酸的流动注射化学发光新方法。 研究了影响化学发光强度的因素,并初步探讨了可能的发光机理。 在最佳化学发光条件下,化学发光强度与5-磺基水杨酸浓度在5.0×10-8~2.0×10-5 mol/L范围内呈良好的线性关系,检出限为1.0×10-8 mol/L,对5.0×10-6 mol/L的5-磺基水杨酸平行测定9次,其相对标准偏差为2.7%。 该法可用于强力霉素废水中5-磺基水杨酸的测定。