Pyrolysis of textile wastes: I. Kinetics and yields

Thermal behavior of textile waste was studied by thermogravimetry at different heating rates and also by semi-batch pyrolysis. It was shown that the onset temperature of mass loss is within 104–156 °C and the final reaction temperature is within 423–500 °C. The average mass loss is 89.5%. There are three DTG peaks located at the temperature ranges of 135–309, 276–394 and 374–500 °C, respectively. The first two might be associated with either with decomposition of the hemicellulose and cellulose or with different processes of cellulose decomposition. The third peak is possibly associated to a synthetic polymer. At a temperature of 460 °C, the expected amount of volatiles of this waste is within 85–89%. The kinetic parameters of the individual degradation processes were determined by using a parallel model. Their dependence on the heating rate was also established. The pyrolysis rate is considered as the sum of the three reaction rates. The pyrolysis in a batch reactor at 700 °C and nitrogen flow of 60 ml/min produces 72 wt.% of oil, 13.5 wt.% of gas and 12.5 wt.% of char. The kinetic parameters of the first peak do not vary with heating rate, while those of the second and the third peak increase and decrease, respectively, with an increasing heating rate, proving the existence of complex reaction mechanisms for both cases.     

Adsorption kinetics of various gases in carbon molecular sieves (CMS) produced from palm shell

Carbon molecular sieves (CMS) have been prepared from locally available palm shell of Tenera type by a thermal treatment technique involving carbonization followed by steam activation and benzene deposition technique. Carbonization of the dried palm shells was done at 900 °C for duration of 1 h followed by steam activation at 830 °C for 30–420 min to achieve activated carbons with different degree of burn-offs. The highest micropore volume of activated carbon obtained at 53.2% burn-off was found suitable to be used as a precursor for CMS production. Subsequent benzene deposition onto activated samples at temperature range from 600 to 900 °C for various benzene concentrations have resulted in a series of CMS with different kinetic selectivities. The molecular sieving behaviour of the CMS products was assessed by kinetic adsorption isotherms of O₂, N₂, CO₂ and CH₄ at room temperature.     

Thermogravimetric and FTIR studies of chitosan blends

Results of spectrophotometric and thermogravimetric studies of chitosan (CH) blends with polyvinyl alcohol (PVAL), starch (S) and hydroxypropylcellulose (HPC) obtained by casting from solutions in the form of transparent films containing 0–1.0 weight fraction of CH were discussed. Blends containing S are homogeneous only in the case of low-weight fraction of S (to 0.3).On the basis of results of thermodegradation in dynamic and isothermal conditions, thermal stability of the tested systems was estimated. Thermogravimetric measurements in dynamic conditions were carried out in the temperature range of 100–450 °C at constant heating rate 15 °C/min. From thermogravimetry (TG) and DTG curves the activation energy and characteristic parameters of degradation of the tested blends were determined. The observed growth of activation energy and T_p—temperature of initial weight loss, T_max—temperature of maximal rate and C_e—degree of conversion at the end of the measurement (at temperature 450 °C) along with the increase of polymer fraction (HPC and S) in the CH blend provides an evidence of improved thermal stability of the systems tested.Investigations in isothermal conditions in air at temperature from 100 to 200 °C confirmed appreciable improvement of CH thermal stability in the blends being tested.Infrared spectroscopic analysis of the blends showed a distinct stabilization of the process of chain scission. In the band at 1080 cm⁻¹ associated with absorption in –C–O–C– group during degradation of the blends at temperature 200 °C much smaller decrease due to molecular scission were observed than in the case of pure CH.     

Influence of thermal treatment on the glass transition temperature of thermosetting epoxy laminate

The influence of accelerated thermal treatment of thermosetting epoxy laminate on its glass transition temperature was studied. Lamplex^® FR-4 glass fibre-reinforced epoxy laminate (used for printed circuit board manufacturing) was used in these experiments. The composite was exposed to thermal treatments at temperatures ranging from 170 °C to 200 °C for times ranging from 10 to 480 h. The glass transition temperature (T_g) was analysed via dynamic mechanical analysis (DMA). It has been proven that the glass transition temperature rapidly decreases in reaction to thermal stress. The obtained T_g data were used for Arrhenius plots for different critical temperatures (T_g-crit. = 105–120 °C). From their slopes (?E_a/R), the activation energy of the thermal degradation process was calculated as 75.5 kJ/mol. In addition to this main relaxation mechanism, DMA also recorded one smaller relaxation process in the most aged samples. Microscopic analysis of the sample structure showed the presence of pronounced small regions of degradation both on the surface and in the inner structure, which are probably the causes of microscopic delamination and the smaller relaxation process.     

Kinetics of hematite chlorination with Cl2 and Cl2 + O2: Part I. Chlorination with Cl2

Preliminary tests of the chlorination of two iron oxides (wüstite and hematite) in various chlorinating gas mixtures were performed by thermogravimetric analysis (TGA) under non-isothermal conditions. Wüstite started to react with chlorine from about 200 °C generating ferric chloride and hematite as the final reaction products. The presence of a reducing and oxidizing agent in the chlorinating gas mixtures influenced the chlorination reactions of both iron oxides, during non-isothermal treatment, only at temperatures higher than 500 °C.The chlorination kinetics of hematite with Cl₂ have been studied in details between 600 and 1025 °C under isothermal chlorination. The values of the apparent activation energy (E_a) were about 180 and 75 kJ/mol in the temperature ranges of 600–875 and 875–1025 °C, respectively. The apparent reaction order with respect to Cl₂ was found to be 0.67 at 750 °C. Mathematical model fitting of the kinetics data was carried out to determine the most probable reaction mechanisms.     

Thermal stability studies on clay nanocomposites prepared from a degradable poly(ester amide) constituted by glycolic acid and 6-aminohexanoic acid

An intercalated nanocomposite of the organically modified montmorillonite Cloisite C25A and a degradable poly(ester amide) based on glycolic acid and 6-aminohexanoic acid units (poly(glc-alt-amh)) was prepared using a twin-screw co-rotating extruder. The non-isothermal degradation kinetics was investigated by thermogravimetric analysis (TG and DTG) in the temperature range of 50–600 °C at five heating rates (2, 5, 10, 20 and 40 °C/min) and compared with the neat polymer. Significant differences were found since the nanocomposite showed three degradation steps instead of the two decomposition processes detected in the pristine sample. The onset mass loss temperature decreased in the nanocomposite due to the presence of the organo-modifier compound, but the presence of the silicate layers significantly decreased the degradation rate at the last stages of decomposition. Kinetic analysis was performed using the Kissinger method and the isoconversional (Kissinger–Akahira–Sunose and Friedman) methods. The true kinetic triplets (E, A, f(α)) were determined for the first two steps of degradation through the Coats–Redfern and the Invariant Kinetic Parameters methods. The results clearly indicated that the presence of the organo-modified clay modified the mechanisms of degradation.     

Kinetic study of low-temperature conversion of plastic mixtures to value added products

Batch-mode pyrolysis of 200.0 g samples of polymers was studied at low temperature. The cracking reaction was carried out in a stainless-steel autoclave with reaction temperatures of 360, 380, 400 and 420 °C, initial pressure of 6.325 kPa (absolute pressure) and reaction times of 0–240 min. Based on the experimental results, a four-lump kinetic model has been developed to describe the production distribution of the light fractions, middle distillates and heavy fraction. This model reasonably fitted the results in each reaction of operation conditions. It was also found that the pyrolysis kinetics of separated plastic, mixed plastic and mixed plastic containing additives can be described by the same kinetic model. The plastic additives have not had a great influence on the product distribution and kinetics of the mixed plastic pyrolysis. Finally, the optimum conditions of low-temperature conversion of plastic mixtures to value-added products were established. The formation of heavy fractions from HDPE was as high as 70 wt% at 380 °C at a reaction time of 250 min. During the thermal degradation of plastic mixtures, the heavy fractions yielded up 50 wt% for 30 min reaction time at 400 °C. The total activation energies for the conversion of HDPE and the plastic mixtures were estimated to be 217.66 kJ mol⁻¹ and 178.49 kJ mol⁻¹, respectively.     

Study on the Kinetics of Vitamin C Degradation in Fresh Strawberry Juices

Vitamin C is an essential nutrient needed for maintaining the human health. Strawberry fruit have a relatively high content of vitamin C, which is around 40-70 mg/ 100 g strawberries. However, vitamin C which is also known as ascorbic acid is easily degraded during storage. The objective of this research is to study the kinetics of degradation of vitamin C in fresh strawberry juices upon storage and to investigate the effect of storage temperatures and sugar addition on the ascorbic acid loss in strawberry juices. Four different types of fresh strawberry juices were prepared, namely A, B, C, and D. Juices A and C were stored at a room temperature of 28 °C, while samples B and D were stored at a refrigerated temperature of 8 °C. Furthermore, juices A and B were prepared without sugar addition, while sugar was added to juices C and D. The concentration of ascorbic acid in the juice was analyzed using iodimetric titration method. It was monitored every one hour for 8 hours of storage for the kinetics of ascorbic acid degradation study. The results showed that the degradation reaction of vitamin C followed zero-order kinetic models in all types of juices. The degradation reaction rate constants obtained for juices A, B, C, and D were 4.42; 3.63; 2.32; and 1.85 mg vitamin C/(100 ml. h), respectively. The activation energy for the vitamin C degradation in fresh strawberry juices with sugar and without sugar addition was estimated to be 1.90 kcal/ mol and 1.65 kcal/ mol, respectively. In conclusion, the storage at a lower temperature combined with sugar addition could effectively slow the rate of degradation of vitamin C.     

Studies of dielectric characteristics of BaBi2Nb2O9 ferroelectrics prepared by chemical precursor decomposition method

BaBiNb₂O₉ (BBN) powders in the nanometer range were prepared by chemical precursor decomposition method (CPD). TG–DTA showed that precursor sample got freed from organic contaminants at 575 °C. XRD showed that a single phase with the layered perovskite structure of BBN was formed after calcining at 600 °C. No intermediate phase was found during heat treatment at and above 600 °C. The crystallite size (D) and the effective strain (η) were found to be 26 nm and 0.000867, respectively, while the particle size obtained from TEM was 28 ± 2 nm. SEM revealed that the average grain size after sintering at 900 °C for 4 h was ∼1.67 μm. A relative density of ∼93% was obtained using a two-step sintering process at moderate pressure. Dielectric and ferroelectric properties were investigated in the temperature range 50–500 °C and frequencies from 1 kHz to 5 MHz. Strong dispersion of the complex relative dielectric constant was observed including typical relaxor features such as shift of permittivity maximum with frequency and broadening of the peak maximum. The high dielectric constant of 545 measured at 100 kHz and other properties of BBN ceramics were compared to that of BBN prepared by other conventional methods and found to be superior.     

Phase transitions of CaTiO3 ceramics sintered with the aid of NaF and MgF2

New phases with initial composition (1 ? x)CaTiO₃ ? xNaF ? xMgF₂ (0 ≤ x ≤ 0.20) have been prepared at low temperature (950 °C) from mixtures of CaTiO₃ and fluorides NaF and MgF₂. The oxyfluorides obtained have been characterized by X-ray diffraction at room temperature and indexed by isotypy with orthorhombic CaTiO₃. The microstructures of these phases are observed by scanning electron microscopy. Dielectric measurements have been carried out during cooling cycle from 500 °C to room temperature at two frequencies (100 Hz, 1 kHz). Differential scanning calorimetry (DSC), thermogravimetry (TG) and differential thermogravimetry (DTG) analyses have been performed, respectively, from room temperature up to 550 °C (DSC) and 920 °C (TG–DTG). The dielectric measurements revealed two anomalies which have been confirmed by DSC analyses. These phenomena are ascribed to second order phase transitions. The variation of the real permittivity with temperature is in agreement with the class I capacitor specifications. However, the dielectric losses have to be improved.     

Thermal degradation of heavy pyrolytic oil in a batch and continuous reaction system

Degradation of heavy pyrolytic oil obtained from a commercial rotary kiln pyrolysis plant for municipal plastic waste was conducted in batch and continuous reaction systems. The experiment was conducted by temperature programming with a 10 °C/min heating rate up to 450 °C and then maintained for a specific time at 450 °C. The product oil was sampled at different degradation temperatures with a specific interval of elapsed time of reaction. In this study, the characteristics of product oil obtained in both batch and continuous reaction systems were compared, according to degradation temperature and elapsed time at 450 °C. Raw pyrolytic oil showed a wide boiling point distribution from around 10 carbon number to about 35 and a high heating value, relative to of those of commercial oils (gasoline, kerosene, and diesel). In the two reaction systems, the characteristics of product oils were influenced by degradation temperature and elapsed time. Moreover, heavy hydrocarbons showed greater cracking at high degradation temperature and long elapsed time into light hydrocarbons as gasoline components range. Also, the continuous reaction system showed different characteristics of product oil, compared with those of the batch reaction system, such as the cumulative amount distribution, production rate, and carbon number distribution of the product oil, as a function of degradation temperature and elapsed time.     

The use of ESR technique for assessment of heating temperatures of archaeological lentil samples

Heat-induced paramagnetic centers in modern and archaeological lentils (Lens culinaris, Medik.) were studied by X-band (9.3 GHz) electron spin resonance (ESR) technique. The modern red lentil samples were heated in an electrical furnace at increasing temperatures in the range 70–500 °C. The ESR spectral parameters (the intensity, g-value and peak-to-peak line width) of the heat-induced organic radicals were investigated for modern red lentil (Lens culinaris, Medik.) samples. The obtained ESR spectra indicate that the relative number of heat-induced paramagnetic species and peak-to-peak line widths depends on the temperature and heating time of the modern lentil. The g-values also depend on the heating temperature but not heating time. Heated modern red lentils produced a range of organic radicals with g-values from g = 2.0062 to 2.0035. ESR signals of carbonised archaeological lentil samples from two archaeological deposits of the Van province in Turkey were studied and g-values, peak-to-peak line widths, intensities and elemental compositions were compared with those obtained for modern samples in order to assess at which temperature these archaeological lentils were heated in prehistoric sites. The maximum temperatures of the previous heating of carbonised UA5 and Y11 lentil seeds are as follows about 500 °C and above 500 °C, respectively.     

Kinetics of Calcium Oxalate Reduction in Taro (Colocasia Esculenta) Corm Chips during Treatments Using Baking Soda Solution

The oxalates content has caused limited utilizations of taro (Colocasia esculenta) as a food material. The insoluble oxalates, especially needle like calcium oxalate crystal may cause irritation, and swelling of mouth and throat. Removal of oxalates in food can be done by physical processes, such as soaking, boiling, and cooking or chemical process by converting them into soluble phases. The purpose of this research were to investigate the effects of baking soda concentration (0-10% w/w) and temperatures (70-97 °C) on the reduction of calcium oxalate content in the taro corm chips and to develop a kinetic model of that process during boiling in baking soda solution. The kinetic model development was done by considering the dissolution of calcium oxalate, chemical reaction and thermal degradation that take place during boiling. The experimental results showed that increasing of baking soda concentration and temperatures were found to increase the reduction of calcium oxalate in the taro corm chips. Based on the product's functional properties, the best condition for calcium oxalate reduction was soaking in 10% w/w baking soda solution for 2 hours followed by boiling at 90 °C for 60 minutes. The kinetic modeling concluded that the calcium oxalate reduction was found to follow a pseudo first order reaction. The modeling results showed that the model is able to represent the phenomena quite well with the apparent reduction rate constant, k = 15.77 Exp (21.239)/RT minute^-1.     

Kinetics of tetrabromobisphenol A pyrolysis. Comparison between correlation and mechanistic models

Brominated flame retardants are well recognized as being highly effective flame retardants. 4-4′-Isopropylidenebis(2,6-dibromophenol), commonly known as tetrabromobisphenol A, is the brominated flame retardant with the largest production volume and is used to improve fire safety, mainly of laminates in electrical and electronic equipment. A kinetic study of the pyrolysis of TBBA has been carried out to obtain decomposition parameters under different operating conditions and taking into account that TBBA is a compound with a high boiling point and that vaporization occurs simultaneously to decomposition. Dynamic runs and dynamic + isothermal run at different heating rates and using different masses of sample were correlated simultaneously. All TG runs were fitted with a unique set of kinetic parameters that is able to explain all the experiments. Moreover, a simplified detailed kinetic model has been developed and the kinetic parameters obtained satisfactorily reproduce the thermal decomposition of TBBA.     

Temperature effect on the chemical composition of a polytetrafluoroethylene surface under the irradiation of synchrotron radiation by means of the X-ray photoelectron spectroscopy

The chemical composition and components of a polytetrafluoroethylene (PTFE) surface was investigated as a function of the temperature under the irradiation of synchrotron radiation (SR) by the X-ray photoelectron spectroscopy (XPS). When the temperature of PTFE under the SR irradiation was less than 100 °C, the C-rich surface appeared. With increasing the temperature more than 150 °C, the relative intensity of the F 1s peak to the C 1s peak increased markedly. At the temperatures of 150–180 °C, the C–C component became small and the CF₂ component was dominant. With further increasing the temperature more than 200 °C, CF₃, CF and C–CF components grew in addition to CF₂ component. Based on these XPS results, the temperature effect on the chemical composition and components is discussed.     

An investigation on the solid state pyrolytic decomposition of bimetallic oxalate precursors of Ca,Sr and Ba with cobalt: A mechanistic approach

The mixed metal oxalate precursors, calcium(II)bis(oxalato)cobaltate(II)hydrate (COC), strontium(II)bis(oxalato)cobaltate(II)pentahydrate (SOC) and barium(II)bis(oxalato)cobaltate(II)octahydrate (BOC) have been synthesized and their thermal stability was investigated. The complexes were characterized by elemental analysis, IR spectral and X-ray powder diffraction studies. Thermal decomposition studies (TG, DTG and DTA) in air showed that the compound COC decomposed mainly to CaC₂O₄ and Co₃O₄ at 340 °C, and a mixture of CaCO₃ and Co₃O₄ identified at 510 °C. A mixture of CaCO₃ and Ca₃Co₂O₆ along with the oxides and carbides of both the cobalt and calcium were attributed at 1000 °C as end products. DSC study in nitrogen ascertained the formation of a mixture of CaO and CoO along with a trace of carbon at 550 °C. The mixture species, SrC₂O₄, CoC₂O₄ and Co₃O₄ were generated at 255 °C in case of SOC in air, which ultimately changed to CoSrO₃, SrCO₃ and oxides of strontium and cobalt at 1000 °C. The several mixture species also generated as intermediate at 332 and 532 °C. The DSC study in nitrogen indicated the formation of CoSrO_x (0.5 < x < 1) as end product. In case of BOC in air, a mixture of BaCoO₂, BaO, CoO and carbides are identified as end product at 1000 °C through the generation of several intermediate species at 350 and 530 °C. A mixture of BaO and CoO is identified as end product in DSC study in nitrogen. The kinetic parameters have been evaluated for all the dehydration and decomposition steps of all the three compounds using four non-mechanistic equations. Using seven mechanistic equations, the kind of dominance of kinetic control mechanism of the dehydration and decomposition steps are also inferred. The kinetic parameters, ΔH and ΔS of all the steps are explored from the DSC studies. Some of the decomposition products are identified by IR and X-ray powder diffraction studies.     

Semivolatile and volatile compounds from the pyrolysis and combustion of polyvinyl chloride

Emissions evolved from the pyrolysis and combustion of polyvinyl chloride (PVC) were studied at four different temperatures (500, 700, 850 and 1000 °C) in a horizontal laboratory tubular quartz reactor in order to analyse the influence of both temperature and reaction atmosphere on the final products from thermal and oxidative reactions. It was observed that the CO₂/CO ratio increased with temperature. Methane was the only light hydrocarbon whose yield increased with temperature up to 1000 °C. Benzene was rather stable at high temperatures, but in general, combustion at temperatures above 500 °C was enough to destroy light hydrocarbons. Semivolatile hydrocarbons were collected in XAD-2 resin and more than 160 compounds were detected. Trends on polyaromatic hydrocarbon (PAH) yields showed that most had a maximum at 850 °C in pyrolysis, but naphthalene at 700 °C. Formation of chlorinated aromatics was detected. A detailed analysis of all isomers of chlorobenzenes and chlorophenols was performed. Both of them reached higher total yields in combustion runs, the first ones having a maximum at 700 °C and the latter at 500 °C. Pyrolysis and combustion runs at 850 °C were conducted to study the formation of polychlorodibenzo-p-dioxins (PCDDs) and polychlorodibenzofurans (PCDFs). There was more than 20-fold increase in total yields from pyrolysis to combustion, and PCDF yields represented in each case about 10 times PCDD yields.     

Evaluation of the porous structure development of chars from pyrolysis of rice straw: Effects of pyrolysis temperature and heating rate

The effects of pyrolysis temperature and heating rate on the porous structure characteristics of rice straw chars were investigated. The pyrolysis was done at atmospheric pressure and at temperatures ranging from 600 to 1000 °C under low heating rate (LHR) and high heating rates (HHR) conditions. The chars were characterized by ultimate analysis, field emission scanning electron microscope (FESEM), helium density measurement and N₂ physisorption method. The results showed that temperature had obvious influence on the char porous characteristics. The char yield decreased by approximately 16% with increasing temperature from 600 to 1000 °C. The carbon structure shrinkage and pore narrowing occurred above 600 °C. The shrinkage of carbon skeleton increased by more than 22% with temperatures rising from 600 to 1000 °C. At HHR condition, progressive increases in porosity development with increasing pyrolysis temperature occurred, whereas a maximum porosity development appeared at 900 °C. The total surface area (S_total) and micropore surface area (S_micro) reached maximum values of 30.94 and 21.81 m²/g at 900 °C and decreased slightly at higher temperatures. The influence of heating rate on S_total and S_micro was less significant than that of pyrolysis temperature. The pore surface fractal dimension and average pore diameter showed a good linear relationship.     

Serum albumin ligand binding volumes using high pressure denaturation

The pressure shift assay (PSA, also termed either PressureFluor or differential pressure fluorimetry) was used to study the thermodynamics of decanoate and dodecanoate lipid binding to human serum albumin (HSA) in the temperature range from 25 °C to 80 °C and the pressure range from 0.1 MPa to 400 MPa. The ligands stabilized HSA against both pressure and temperature denaturation. The P–T phase diagram for HSA bound to saturated fatty acids is shown. Pressure induced HSA denaturation reversibility is demonstrated via either intrinsic tryptophan or extrinsic probe 1,8-anilinonaphthalene sulfonate (ANS) fluorescence. The effect of guanidinium in a PSA was studied. PSA provides information on ligand binding volumes. The volume changes from protein–ligand binding are thermodynamically important and could be used in designing compounds with specific volumetric binding properties.     

Enhanced electrical conductivity in Ce0.79Gd0.20Co0.01O2−δ for low temperature solid oxide fuel cell applications

Very high electrical conductivity of ～0.021 S/cm at 600 °C is obtained in Ce_0.79Gd_0.20Co_0.01O_2?δ. Corresponding activation energy of conduction ～0.43 eV measured in the temperature range of 400–700 °C is found to be notably low. Improved electrical properties with 99% of the theoretical density as obtained for these specimens, prepared using powder of average particle size ～20 nm and subsequent sintering at 1100 °C, is considered to be a significant step to reduce the processing temperature. The measured electrical potential of ～1 V indicates the suitability of its use as an electrolyte in electrochemical devices.