Electrochemical properties of niosomes modified Au electrode and DNA recognition

Non-ionic surfactant vesicles (NSVs), also referred to as niosomes, have been studied as an alternative to conventional liposomes. In this paper, electrochemical inspection of the interaction between Herring sperm DNA and niosomes has been investigated after a simple and novel method for the formation of niosomes on Au electrode. Each step of electrode modification has been confirmed with cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The assembly of octadecanethiol (ODT) layer on the electrode surface generates a packed film that introduces a barrier to the interfacial electron transfer (R(et)), and the subsequent immobilization of niosomes onto the self-assembled monolayer (SAM) layer results in a further increase of R(et), due to the formed bilayer almost blocked the redox probe to the electrode surface. When Herring sperm DNA was added, the R(et) value decreased, indicating that the barrier of the redox probe to the surface was disrupted. The addition of DNA caused the formation of some transmembrane channels for the redox probe across the niosomes. A good linear relationship between R(et) value and DNA concentration was found over the 0-0.05 mg mL(-1) concentration range.     

A disposable impedance sensor for electrochemical study and monitoring of adhesion and proliferation of K562 leukaemia cells

A polyaniline-modified screen-printed carbon electrode (PANI/SPCE) was prepared by electropolymerization for the construction of a novel disposable cell impedance sensor. The conductive polymer improved greatly the electron transfer of SPCE and was very effective for cell immobilization. The adhesion of cells increased the electron transfer resistance (R_et) of redox probe on the PANI/SPCE surface, producing an impedance sensor for K562 leukaemia cells with a semilogarithm linear range from 10⁴ to 10⁷ cells ml⁻¹ and a limit of detection of 8.32 × 10³ cells ml⁻¹ at 10σ. The proliferation of cells on the conductive polymer increased the R_et, leading to a novel way to monitor the growth process of cells on the PANI/SPCE. The electrochemical monitoring indicated K562 leukaemia cells cultured in vitro on the PANI surface were viable for 60 h, consistent with the analysis from microscopic imaging and MTT assay. This method for monitoring the surface proliferation and detecting the number of viable cells was simple, low-cost and disposable, thus providing a convenient avenue for electrochemical study of cell immobilization, adhesion, proliferation and apoptosis.     

Label-free and sequence-specific DNA detection down to a picomolar level with carbon nanotubes as support for probe DNA

This study describes a simple and label-free electrochemical impedance spectroscopic (EIS) method for sequence-specific detection of DNA by using single-walled carbon nanotubes (SWNTs) as the support for probe DNA. SWNTs are confined onto gold electrodes with mixed self-assembly monolayers of thioethanol and cysteamine. Single-stranded DNA (ssDNA) probe is anchored onto the SWNT support through covalent binding between carboxyl groups at the nanotubes and amino groups at 5′ ends of ssDNA. Hybridization of target DNA with the anchored probe DNA greatly increases the interfacial electron-transfer resistance (R_et) at the double-stranded DNA (dsDNA)-modified electrodes for the redox couple of Fe(CN)₆^3−/4−, which could be used for label-free and sequence-specific DNA detection. EIS results demonstrate that the utilization of SWNTs as the support for probe DNA substantially increases the surface loading of probe DNA onto electrode surface and thus remarkably lowers the detection limit for target DNA. Under the conditions employed here, R_et is linear with the concentration of target DNA within a concentration range from 1 to 10 pM with a detection limit down to 0.8 pM (S/N = 3). This study may offer a novel and label-free electrochemical approach to sensitive sequence-specific DNA detection.     

Amperometric sensor for hydrogen peroxide based on direct electron transfer of spinach ferredoxin on Au electrode

A protein-based electrochemical sensor for hydrogen peroxide (H₂O₂) was developed by an easy and effective film fabrication method where spinach ferredoxin (Fdx) containing [2Fe–2S] metal center was cross linked with 11-mercaptoundecanoic acid (MUA) on a gold (Au) surface. The surface morphology of Fdx molecules on Au electrodes was investigated by atomic force microscopy (AFM). Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) were employed to study the electrochemical behavior of adsorbed Fdx on Au. The interfacial properties of the modified electrode were evaluated in the presence of Fe(CN)₆^3?/4? redox couple as a probe. From CV, a pair of well-defined and quasi-reversible redox peaks of Fdx was obtained in 10 mM, pH 7.0 Tris–HCl buffer solution at ?170 and ?120 mV respectively. One electron reduction of the [2Fe-2S]²⁺ cluster occurs at one of the iron atoms to give the reduced [2Fe-2S]⁺. The formal reduction potential of Fdx ca. ?150 mV (vs. Ag/AgCl electrode) at pH 7.0. The electron-transfer rate constant, k_s, for electron transfer between the Au electrode and Fdx was estimated to be 0.12 s^?1. From the electrochemical experiments, it is observed that Fdx/MUA/Au promoted direct electron transfer between Fdx and electrode and it catalyzes the reduction of H₂O₂. The Fdx/MUA/Au electrode displays a linear increase in amperometric current for increasing concentration of H₂O₂.The sensor calibration plot was linear with r² = 0.998 with sensitivity approximately 68.24 μAm M^?1 cm^?2. Further, the effect of nitrite on the developed sensor was examined which does not interfere with the detection of H₂O₂. Finally, the addition of H₂O₂ on MUA/Au electrode was observed which has no effect on amperometric current.     

CtrA gene based electrochemical DNA sensor for detection of meningitis

Electrochemical DNA sensor has been fabricated by immobilizing thiolated single stranded oligonucleotide (ssDNA) probe onto gold (Au) coated glass electrode for meningitis detection using hybridization with complementary DNA (CtrA) in presence of methylene blue (MB). These electrodes (ssDNA/Au and dsDNA/Au) have been characterized using atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FT-IR), electrochemical impedance spectroscopy (EIS) and cyclic voltammetric (CV) technique. The DNA/Au electrode can detect the complementary DNA in the range of 7–42 ng/μl in 5 min (hybridization) with response time 60 s and electrode is stable for about 4 months when stored at 4 °C. The sensitivity of dsDNA/Au electrode is 115.8 μA/ng with 0.917 regression coefficient (R).     

Electrochemically activated MnO as a cathode material for sodium-ion batteries

Besides classical electrode materials pertaining to Li-ion batteries, recent interest has been devoted to pairs of active redox composites having a redox center and an intercalant source. Taking advantage of the NaPF₆ salt decomposition above 4.2 V, we extrapolate this concept to the electrochemical in situ preparation of F-based MnO composite electrodes for Na-ion batteries. Such electrodes exhibit a reversible discharge capacity of 145 mAh g^− 1 at room temperature. The amorphization of pristine MnO electrode after activation is attributed to the electrochemical grinding effect caused by substantial atomic migration and lattice strain build-up upon cycling.     

Mesoporous silica thin films for molecular sieving and electrode surface protection against biofouling

Electrode fouling is a major challenge for the long term use of sensors in real samples as it leads to the decay of the electroanalytical signal and is often caused by the formation of an inhibiting layer formed by biomolecules. We demonstrate here that ordered and vertically aligned mesoporous silica generated at the surface of an indium tin oxide electrode by electrochemically assisted self-assembly act as a molecular sieve and a protective layer for the electrode surface. They indeed prevent the adsorption of size excluded large undesired molecules (e.g. haemoglobin) while allowing the detection of small redox active molecules likely to reach the electrode surface through the film (e.g. propranolol) with almost no loss of sensitivity. At a bare electrode, the oxidation of propranolol is completely inhibited in the presence of 5 μM haemoglobin. At a modified electrode, the sensitivity for propranolol in the absence of haemoglobin is (72.8 ± 2.9) mA mol^− 1 (R² = 0.992, N = 7) and it remains similar in the presence of 5 μM haemoglobin with a value of (67.4 ± 7.2) mA mol^− 1 (R² = 0.992, N = 7).     

Electrochemical impedance spectroscopy detection of lysozyme based on electrodeposited gold nanoparticles

A simple, highly sensitive, and label-free electrochemical impedance spectroscopy (EIS) aptasensor based on an anti-lysozyme-aptamer as a molecular recognition element, was developed for the detection of lysozyme. Improvement in sensitivity was achieved by utilizing gold nanoparticles (AuNPs), which were electrodeposited onto the surface of a gold electrode, as a platform for immobilization of the aptamer. To quantify the amount of lysozyme, changes in the interfacial electron transfer resistance (R_et) of the aptasensor were monitored using the redox couple of an [Fe(CN)₆]^3−/4− probe. The R_et increased with lysozyme concentration. The plot of R_et against the logarithm of lysozyme concentration is linear over the range from 0.1 pM to 500 pM with a detection limit of 0.01 pM. The aptasensor also showed good selectivity for lysozyme without being affected by the presence of other proteins.     

Zeptomolar detection of Hg2 + based on label-free electrochemical aptasensor: One step closer to the dream of single atom detection

An ultra-sensitive and highly selective electrochemical label-free aptasensor is proposed for the quantitation of Hg^2 + based on the hybridization/dehybridization of double-stranded DNA (dsDNA) on a gold electrode. Thiol-substituted single-stranded DNA (ssDNA) is self-assembled on the gold electrode surface through the SAu interaction. The hybridization of ssDNA with complementary DNA (cDNA) and the consequences of dehybridization in the presence of mercury ions are followed through differential pulse voltammetry (DPV) responses using a [Fe(CN)₆]^{3 −/4 −} redox probe. The formation of a thymine–Hg^2 +–thymine (T–Hg^2 +–T) complex is the key to producing a highly selective and sensitive aptasensor for Hg^2 + determination. Specifically, the present electrochemical aptasensor is able to quantify Hg^2 + ions in concentrations from 5 zeptomolar (zM) to 55 picomolar (pM) with a limit of detection of 0.6 zM, close to the dream of single atom detection, without requiring a complicated procedure or expensive materials.     

An electrochemical approach tunes the electric property of benzoylferrocene-modified supported lipid membrane

A benzoylferrocene (BFc) supported 3-sn-phosphatidylcholine (PC) film electrode was prepared by casting the solution of BFc and PC in chloroform onto the surface of platinum (Pt). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) results showed that BFc, retained in the biological membrane, acted as a shuttle for electron transfer across the supported bilayer lipid membranes (s-BLMs). Doping of BFc increased membrane conductivity, while electrochemical oxidation of BFc greatly changed the membrane conductivity, the membrane impedance characterized by charge transfer resistance (R_ct) dramatically increased about 400 times (from 10.32 to 3919.67 kΩ). Interestingly, the electrochemical oxidized BFc buried in the membranes could be reduced by applying a low potential, and this led to recurrent of a conductive membrane. The conductivity of the s-BLMs could be controlled by the redox status of embedded BFc molecules. The approach provided a facile and novel way to electrochemically control the membrane conductance of s-BLMs by embedding BFc as a switchable redox mediator.     

Rapid formation of well-ordered self-assembled monolayers of dodecanethiol on polycrystalline gold by microwave irradiation

This article reports a rapid method of preparing self-assembled monolayers of dodecanethiol (C₁₂SH-SAMs) on polycrystalline gold by microwave irradiation (MWI, 650 W, duty cycle is 10%). The qualities of C₁₂SH-SAMs were characterized by both cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results show that the C₁₂SH-SAMs formed by MWI in 120 s (C₁₂SH-SAMs_MWI,120 s) have low ionic permeability (the differential capacitance C_d values are independent of the scan rate and phase angle at 1 Hz Φ_1 Hz = 89 ± 0.9°), excellent electrochemical blocking ability towards the redox probe (the current i_MWI,120 s obtained from CV is lowest when compared to other SAMs and charge transfer resistance R_ct = (1.15 ± 0.19) × 10⁶ Ω cm²), and high surface coverage (99.996 ± 0.001%).     

The electrode responses of a tungsten bronze electrode differ in potentiometry and voltammetry and give access to the individual contributions of electron and proton transfer

A tungsten wire covered with Na_0.75WO₃ acts in potentiometry as a reversible pH electrode having a pH dependent open-circuit potential E_ocp with nernstian slope. The mid-peak potential E_mp of cyclic voltammograms also depends on pH. At low pH (e.g., pH 2) and slow scan rates (e.g., 2 mV s^–1) the voltammetric response is almost completely reversible. At higher pH and faster scan rates, the voltammetric systems exhibit features of increasing irreversibility. Under the conditions of reversibility, the E_ocp and E_mp differ significantly. E_ocp is determined by the proton transfer at the electrode surface; whereas E_mp is determined by the electron transfer equilibrium tungsten(VI)/tungsten(V) and the proton transfer at the electrode surface. The difference between E_ocp and E_mp provides the individual thermodynamic contributions of electron and proton transfer to the overall pH dependent redox electrode. This is the first time that both contributions can be separated for an insertion electrochemical system (thin surface layer). It is also shown for the first time that the mechanism of an ion-sensitive electrode can differ in potentiometry and voltammetry.     

In-channel modification of electrochemical detector for the detection of bio-targets on microchip

The coulometric efficiency (C_eff) of an amperometric detector integrated on PDMS/glass capillary electrophoresis microfluidic device (microchip) has been enhanced by in-channel electrochemical modification. In-channel electrochemical deposition of gold particles was performed in order to vertically increase the surface area of the Au sensing microelectrode. The roughness of the electrodes was characterized using scanning electron microscopy and profilometric analysis. The degree of electrode modification was also characterized by roughness factor determination. Separation processes including detection potential was optimized and the analytical performance of the microchip was tested using a mixture of dopamine (DA) and catechol (CA). The modified electrochemical detector provided well-resolved separation of DA and CA in less than 60 s with enhanced sensitivity; no peak broadening was observed. The limit of detection using in-channel modification of working electrode for DA and CA are 60 and 110 nM, respectively. Thus, in-channel electrochemical deposition of metallic particles should be used to enhance the C_eff of integrated amperometric detection of analytes with good redox properties in order to obtain lower LODs.     

End-labeling of peptide nucleic acid with osmium complex. Voltammetry at carbon and mercury electrodes

Peptide nucleic acid (PNA), the DNA mimic with electrically neutral pseudopeptide backbone, is intensively used in biotechnologies and particularly in single-base mismatch detection in DNA hybridization sensors. We propose a simple method of covalent end-labeling of PNA with osmium tetroxide, 2,2′-bipyridine (Os,bipy). Os,bipy-modified PNA (PNA–Os,bipy) produces voltammetric stripping peaks at carbon and mercury electrodes. Peak potential (E_p) of one of the anodic peaks of PNA–Os,bipy at the pyrolytic graphite electrode (PGE) differs from E_p of the reagent, allowing PNA–Os,bipy analysis directly in the reaction mixture. At the hanging mercury drop electrode (HMDE) the PNA–Os,bipy yields a catalytic peak Cat_p, in addition to the redox couples. Using Cat_p it is possible to detect purified PNA–Os,bipy down to 1 pM concentration at accumulation time 60 s. To our knowledge this is the highest sensitivity of the electrochemical detection of PNA.     

Electrosynthesis of polythiophene nanowires via mesoporous silica thin film templates

Early electrosynthesized polythiophene nanowires were prepared employing a mesoporous silica template, which was also electrochemically produced. A cathodic potential step was applied to a fluorine doped tin oxide conducting glass electrode in a cationic surfactant and silicate reagent medium to deposit highly ordered mesoporous silica films. To evaluate the pores order and, consequently, optimal deposition potential, the electrochemical response of the electrodes was studied using ferrocene as redox probe. The modified electrodes were used to accomplish polythiophene electrodeposits employing 0.6 mM thiophene and 0.1 M tetrabutylammonium hexafluorophosphate in anhydrous CH₃CN as working solution. Transmission electron microscope images of the deposits revealed the presence of polythiophene nanowires of about 6 nm in diameter arranged normal to the electrode surface. The unprecedented small size and arrangement of the obtained nanowires place this work as the first study that successfully accomplished the formation of nanoscale electrochemically synthesized conducting polymer nanowires.     

Highly sensitive electrochemical impedance spectroscopic detection of DNA hybridization based on Aunano-CNT/PANnano films

A polyaniline nanofibers (PAN_nano)/carbon paste electrode (CPE) was prepared via dopping PAN_nano in the carbon paste. The nanogold (Au_nano) and carbon nanotubes (CNT) composite nanoparticles were bound on the surface of the PAN_nano/CPE. The immobilization and hybridization of the DNA probe on the Au_nano-CNT/PAN_nano films were investigated with differential pulse voltammetry (DPV) and cyclic voltammetry (CV) using methylene blue (MB) as indicator, and electrochemical impedance spectroscopy (EIS) using [Fe(CN)₆]^3−/4− as redox probe. The voltammetric peak currents of MB increased dramatically owing to the immobilization of the probe DNA on the Au_nano-CNT/PAN_nano films, and then decreased obviously owing to the hybridization of the DNA probe with the complementary single-stranded DNA (cDNA). The electron transfer resistance (R_et) of the electrode surface increased after the immobilization of the probe DNA on the Au_nano-CNT/PAN_nano films and rose further after the hybridization of the probe DNA. The remarkable difference between the R_et value at the DNA-immobilized electrode and that at the hybridized electrode could be used for the label-free EIS detection of the target DNA. The loading of the DNA probe on Au_nano-CNT/PAN_nano films was greatly enhanced and the sensitivity for the target DNA detection was markedly improved. The sequence-specific DNA of phosphinothricin acetyltransferase (PAT) gene and the polymerase chain reaction (PCR) amplification of nopaline synthase (NOS) gene from transgenically modified beans were determined with this label-free EIS DNA detection method. The dynamic range for detecting the PAT gene sequence was from 1.0 × 10⁻¹² mol/L to 1.0 × 10⁻⁶ mol/L with a detection limit of 5.6 × 10⁻¹³ mol/L.     

Label-free electrochemical detection of Avian Influenza Virus genotype utilizing multi-walled carbon nanotubes–cobalt phthalocyanine–PAMAM nanocomposite modified glassy carbon electrode

A novel DNA electrochemical biosensor for label-free determination of DNA sequence related to the Avian Influenza Virus (AIV) genotype was demonstrated in this paper. First, the multi-walled carbon nanotubes–cobalt phthalocyanine (MWNTs–CoPc) nanocomposite and poly (amidoamine) (PAMAM) dendrimer (generation 4.0) were modified on the glassy carbon electrode (GCE) sequentially. Then, DNA probes were successfully immobilized on the modified electrode with G4 PAMAM dendrimer acting as the coupling agent. The hybridization events were monitored by differential pulse voltammetry (DPV) measurement based on the oxidation signals of guanine without any external labels. Under the optimal conditions, the difference in guanine oxidation signal of the probe modified GCE in the absence and presence of complementary target (ΔI_p) was linear with the logarithmic value of the complementary target concentration from 0.01 to 500 ng/ml with a correlation coefficient of 0.998 and a detection limit of 1.0 pg/ml.     

Direct electrochemistry and electrocatalysis of hemoglobin in sodium alginate film on a BMIMPF6 modified carbon paste electrode

A room temperature ionic liquid (RTIL) modified carbon paste electrode was constructed based on the substitute of paraffin with 1-butyl-3-methyl-imidazolium hexafluorophosphate (BMIMPF₆) as binder for carbon paste. Direct electrochemistry and electrocatalytic behaviors of hemoglobin (Hb) entrapped in the sodium alginate (SA) hydrogel film on the surface of this carbon ionic liquid electrode (CILE) were investigated. The presence of IL in the CILE increased the electron transfer rate and provided a biocompatible interface. Hb remained its bioactivity on the surface of CILE and the SA/Hb modified electrode showed a pair of well-defined, quasi-reversible cyclic voltammetric peaks with the apparent standard potential (E^0′) at about −0.344 V (vs. SCE) in pH 7.0 Britton–Robinson (B–R) buffer solution, which was attributed to the Hb Fe(III)/Fe(II) redox couple. UV–Vis absorption spectra indicated that heme microenvironment of Hb in SA film was similar to its native status. Hb showed a thin-layer electrochemical behavior in the SA film with the direct electron transfer achieved on CILE without the help of electron mediator. Electrochemical investigation indicated that Hb took place one proton with one electron electrode process and the average surface coverage of Hb in the SA film was 3.2 × 10⁻¹⁰ mol/cm². The immobilized Hb showed excellent electrocatalytic responses to the reduction of H₂O₂ and nitrite.     

Direct electrochemistry of hemoglobin and glucose oxidase in electrodeposited sol–gel silica thin films on glassy carbon

This work points out that electrogeneration of silica gel (SG) films on glassy carbon electrodes (GCEs) can be applied to immobilize biomolecules – hemoglobin (Hb) or glucose oxidase (GOD) or both of them in mixture – without preventing their activity. These proteins were physically entrapped in the sol–gel material in the course of the electro-assisted deposition process applied to form the thin films onto the electrode surface. SG films were prepared from a precursor solution by applying a suitable cathodic potential likely to induce a local pH increase at the electrode/solution interface, accelerating thereby polycondensation of the silica precursors with concomitant film formation. Successful immobilization of proteins was checked by various physico-chemical techniques. Both Hb and GOD were found to undergo direct electron transfer, as demonstrated by cyclic voltammetry. GCE–SG–Hb gave rise to well-defined peaks at potentials E_c = −0.29 V and E_a = −0.17 V in acetate buffer, corresponding to the Fe^III/Fe^II redox system of heme group of the protein, while GCE–SG–GOD was characterized by the typical signals of FAD group at E_c = −0.41 V and E_a = −0.33 V in phosphate buffer. These two redox processes were also evidenced on a single voltammogram when both Hb and GOD were present together in the same SG film. Hb entrapped in the silica thin film displayed an electrocatalytic behavior towards O₂ and H₂O₂ in solution, respectively in the mM and μM concentration ranges. Immobilized GOD kept its biocatalytic properties towards glucose. Combined use of these two proteins in mixture has proven to be promising for detection of glucose in solution via the electrochemical monitoring of oxygen consumption (decrease of the oxygen electrocatalytic signal).     

Analysis of a high redox potential heme in tetraheme cytochrome c3 by direct electrochemistry

Cytochrome c₃ from Desulfovibrio vulgaris (Miyazaki F), a redox protein, contains four bis-histidine-coordinated hemes and has lower redox potential than other heme proteins. Direct electrochemical measurements of cytochrome c₃ were carried out using a pyrolytic graphite edge (PGE) electrode. A low redox potential, already measured by redox titration, and a high redox potential (− 245 mV vs. Ag/AgCl) were observed at room temperature. The high redox potential of cytochrome c₃ was similar to that observed for the loss of an axial ligand at heme. To investigate the loss of the histidine ligand, we explored the electrochemistry of four cytochrome c₃ mutants, in which the sixth coordinated histidine was replaced by methionine. The electrochemistry of the cytochrome c₃ mutants indicated that only Heme III undergoes loss of its axial histidine ligand.