Ru/AlOOH催化剂的制备、表征及其苯选择加氢反应的研究

采用共沉淀法制备了Ru/A1OOH催化剂,以XRD,TG/DTA,TEM和氮物理吸附等手段对其基本物化性质进行了表征.在苯液相选择加氢制备环己烯的反应中,该催化剂显示了很高的苯选择加氢活性和选择性,环己烯得率可达35.8%,优于原位焙烧上述催化剂或浸渍法制得的Ru/γ-A1₂O₃催化剂.催化剂结构与催化性能的对比研究进一步揭示催化剂的亲水性和孔结构在苯选择加氢反应中的重要作用.     

高分散 Ru/MMT 催化剂的制备及其催化喹啉加氢性能

 通过简单的离子交换法制备出高分散的蒙脱土 (MMT) 负载 Ru 催化剂, 采用 X 射线衍射、X 射线光电子能谱、程序升温还原和高分辨透射电子显微镜等手段对催化剂进行了表征. 结果表明, 金属 Ru 在蒙脱土层间高度分散, Ru 的平均粒径约 2 nm. 在喹啉加氢反应中, 该催化剂显示出很高的反应活性和选择性. 在 2 MPa 和 60 °C 的温和条件下, 以水为溶剂时, Ru/MMT 催化喹啉加氢生成 1,2,3,4-四氢喹啉的选择性高于 96.4%, 喹啉转化率达 99.2%. 当温度升高到 140 °C、压力增加到 3 MPa 时, 不需要补加催化剂就可以将喹啉一步加氢生成十氢喹啉, 选择性高达 98.1%.     

琥珀酸酐均相加氢制备γ-丁内酯的研究

研究了不同催化剂对琥珀酸酐加氢生成γ -丁内酯的反应 ,并考察了配体、溶剂及PPh3/Ru摩尔比对催化反应的影响。结果发现Ru络合物是最佳催化剂 ,PPh3是最佳配体 ,乙二醇二甲醚为最佳溶剂。在SA ,2 0mmol;催化剂Ru ,0 .10mmol;PPh3/Ru ,8;以乙二醇二甲醚为溶剂( 8ml) ;H2 ,3.0MPa ;反应温度为 12 0℃的反应条件下 ,γ -丁内酯的产率可达 86.5%。     

Ru/HY催化剂催化对苯二酚加氢研究

对苯二酚液相加氢制备1,4-环己二醇的途径环境友好,关键是研究高催化活性的催化剂来提高产物产率.我们以Ru/HY为催化剂用于对苯二酚加氢.用XRD,TEM对催化剂进行了表征,通过吡啶吸附红外对HY酸性的变化进行了讨论.对其反应条件进行了优化.结果表明3.0%Ru/HY的催化剂表现出高的活性,对苯二酚的转化率和1,4-环己二醇的选择性分别为96.5%和68.3%.我们还基于对Ru/HY催化剂结构的研究探讨并提出相应的反应机理.     

A Rechargeable Hydrogen Battery Based on Ru Catalysis

Apart from energy generation, the storage and liberation of energy are among the major problems in establishing a sustainable energy supply chain. Herein we report the development of a rechargeable H₂ battery which is based on the principle of the Ru‐catalyzed hydrogenation of CO₂ to formic acid (charging process) and the Ru‐catalyzed decomposition of formic acid to CO₂ and H₂ (discharging process). Both processes are driven by the same catalyst at elevated temperature either under pressure (charging process) or pressure‐free conditions (discharging process). Up to five charging–discharging cycles were performed without decrease of storage capacity. The resulting CO₂/H₂ mixture is free of CO and can be employed directly in fuel‐cell technology.     

Ceria in hydrogenation catalysis: high selectivity in the conversion of alkynes to olefins

Active and selective: Ceria shows a high activity and selectivity in the gas-phase hydrogenation of alkynes to olefins. This unprecedented behavior has direct impact on the purification of olefin streams and, more importantly, it opens new perspectives for exploring this fascinating oxide as a catalyst for the selective hydrogenation of other functional groups.     

黏土负载镍的纳米片高效芳烃加氢催化剂

以天然层状黏土蒙脱石（MMT）为前体,通过液相沉积-沉淀将镍物种引入水溶液中剥离为MMT纳米片表面的简易方法制得Ni/MMT纳米片。该Ni/MMT纳米片由于是二维（2D）结构,利于芳烃及其加氢产物的传质扩散,相比Ni/SBA-15和Ni/γ-Al₂O₃催化剂,具有更为高效的芳烃加氢性能,且在镍负载量高达18.5%时,其四氢萘加氢的转化频率（TOF）达到最高值。     

Thermoregulated Phase-separable Ru_3(CO)_(12)/PETPP Complex Catalyst for Hydrogenation of Styrene

The basic problem in homogeneous catalysis is the separation of catalyst from the reaction mixtures. To overcome this drawback, a number of methods have been developed. One of them is to attach homogeneous catalyst to supports 1. An alternative and well used approach involves liquid/liquid biphasic catalysis in which the catalyst and product reside in different phases and separation of the products is achieved simply by phase separation2. Recently, a concept of thermoregulated phase transf…     

Rhodium-catalyzed asymmetric hydrogenation of olefins with PhthalaPhos, a new class of chiral supramolecular ligands

A library of 19 binol-derived chiral monophosphites that contain a phthalic acid diamide group (PhthalaPhos) has been designed and synthesized in four steps. These new ligands were screened in the rhodium-catalyzed enantioselective hydrogenation of prochiral dehydroamino esters and enamides. Several members of the library showed excellent enantioselectivity with methyl 2-acetamido acrylate (6 ligands gave >97% ee), methyl (Z)-2-acetamido cinnamate (6 ligands gave >94% ee), and N-(1-phenylvinyl)acetamide (9 ligands gave >95% ee), whilst only a few representatives afforded high enantioselectivities for challenging and industrially relevant substrates N-(3,4-dihydronaphthalen-1-yl)-acetamide (96% ee in one case) and methyl (E)-2-(acetamidomethyl)-3-phenylacrylate (99% ee in one case). In most cases, the new ligands were more active and more stereoselective than their structurally related monodentate phosphites (which are devoid of functional groups that are capable of hydrogen-bonding interactions). Control experiments and kinetic studies were carried out that allowed us to demonstrate that hydrogen-bonding interactions involving the diamide group of the PhthalaPhos ligands strongly contribute to their outstanding catalytic properties. Computational studies carried out on a rhodium precatalyst and on a conceivable intermediate in the hydrogenation catalytic cycle shed some light on the role played by hydrogen bonding, which is likely to act in a substrate-orientation effect.     

Asymmetric Hydrogenation of Unfunctionalized Tetrasubstituted Acyclic Olefins

Asymmetric hydrogenation has evolved as one of the most powerful tools to construct stereocenters. However, the asymmetric hydrogenation of unfunctionalized tetrasubstituted acyclic olefins remains the pinnacle of asymmetric synthesis and an unsolved challenge. We report herein the discovery of an iridium catalyst for the first, generally applicable, highly enantio‐ and diastereoselective hydrogenation of such olefins and the mechanistic insights of the reaction. The power of this chemistry is demonstrated by the successful hydrogenation of a wide variety of electronically and sterically diverse olefins in excellent yield and high enantio‐ and diastereoselectivity.     

离子液体[Bmim]BF4中单分散Ru纳米粒子的制备及选择加氢性能

采用化学还原法在离子液体1-丁基-3-甲基咪唑四氟硼酸盐([BMim]BF₄)中制备了单分散纳米金属Ru粒子。采用X射线衍射(XRD)、透射电镜(TEM)、傅里叶红外光谱(FTTR)及热重(TG)对所制备样品的形貌和结构进行了表征。XRD表征结果显示：在[BMim]BF₄中制备的Ru具有六方紧密堆积结构,无氧化物峰出现;TEM结果显示：采用正滴法制备的Ru纳米粒子为球形颗粒,呈现良好的单分散状态,粒径分布窄,为2~5 nm,而采用反滴法制备的Ru纳米粒子则发生了严重的团聚,团聚体粒径大于10 nm;FTIR表征表明：Ru纳米粒子表面存在[BMim]BF₄液体层,分析二者之间存在较强的物理吸附作用,[BMim]BF₄在Ru纳米粒子的制备中起到了修饰剂和保护剂的双重作用,这一推论通过TG分析得到了进一步验证。将分散于[BMim]BF₄的Ru纳米粒子作为催化剂应用于苯选择加氢反应,结果分析表明：Ru-离子液体-苯反应体系中,苯转化率仅有0.3%;Ru-离子液体-苯-水反应体系中加氢活性较高,但环己烯选择性较低,在一定条件下,加氢30 min,苯转化率为27.3%,环己烯选择性仅为14.5%。     

Highly Selective Olefin Production from CO2 Hydrogenation on Iron Catalysts: A Subtle Synergy between Manganese and Sodium Additives

Mn and Na additives have been widely studied to improve the efficiency of CO₂ hydrogenation to valuable olefins on Fe catalysts, but their effects on the catalytic properties and mechanism are still under vigorous debate. This study shows that Fe-based catalysts with moderate Mn and Na contents are highly selective for CO₂ hydrogenation to olefins, together with low selectivities for both CO and CH₄ and much improved space-time olefin yields compared to state-of-the-art catalysts. Combined kinetic assessment and quasi in situ characterizations further unveil that the sole presence of Mn suppresses the activity of Fe catalysts because of the close contact between Fe and Mn, whereas the introduction of Na mediates the Fe–Mn interaction and provides strong basic sites. This subtle synergy between Na and Mn sheds light on the importance of the interplay of multiple additives that could bring an enabling strategy to improve catalytic activity and selectivity.     

K/MgFeZn-HTLcs催化CO加氢制低碳烯烃性能研究

以MgFeZn-HTLcs为前驱体,制备了不同Mg/Fe/Zn物质的量配比、K改性的K/MgFeZn-HTLcs催化剂,用于CO加氢直接制低碳烯烃反应。采用N2吸附-脱附、SEM、TG、XRD、XPS、H_2-TPR等手段对催化剂进行了表征。结果表明,MgFeZnHTLcs前驱体具有典型的层状结构,孔径分布均一;经焙烧、K改性后仍具有一定的层状结构,但比表面积显著减小,平均孔径增大;新鲜催化剂物相以金属氧化物和铁酸盐为主,反应后K/MgFeZn-HTLcs催化剂主要以Fe_5C_2、MgCO_3和ZnO相存在,K/2Fe-1Zn催化剂主要物相为ZnFe2O_4。在CO加氢反应中,K/MgFeZn-HTLcs催化剂具有较高的C=2-4烯烃选择性和较低的C+5含量,与K/2Fe-1Zn催化剂相比,产物分布明显改善;K/2Mg-2Fe-1Zn催化剂上O/P比值达5.15,C=2-4含量占总烃质量的48.56%。     

Ru-catalyzed Asymmetric Hydrogenation of Aryl Ketones Using Tetrazole Derived NH_2-hybrid Ligand

Readily available chiral hybrid NH₂/tetrazole ligand [(S)‐TEA, 1 ] in combination with Ru‐BINAP or Ru‐DIOP complexes catalyzes the asymmetric hydrogenation of a number of simple ketones with moderate enantioselectivity (up to 72% ee). The tetrazole functionality results in reversal of the typically observed chiral‐induction for related systems and allows for hydrogenation to be uncharacteristically conducted in (non‐protic) THF solvent. The observed catalyst performance is sensitive to the reaction conditions employed and the particular compounds involved. The origins of such features are considered to derive from the added functionality provided by the tetrazole moiety in 1 , which due to its modular nature provides a good basis for further development.     

Acidity of montmorillonite pillared by alumina, zirconia and chromia

Acidic properties of Al-, Zr- and Cr- pillared montmorillonites prepared from Jelšovy Potok bentonite (Central Slovakia) have been investigated using temperature-programmed desorption of ammonia. The number of acid sites varied with different interlayer cations from 0.06 to 0.23 mmol g⁻¹. The character of acid sites was similar in the case of Al- and Zr- forms. It is obvious that the chromium analogue contains fewer acid sites, nevertheless, they seem to be stronger compared to Al- and Zr- pillared montmorillonites.     

Rhodium/Phosphine catalysed selective hydroformylation of biorenewable olefins

This work reports rhodium catalyzed selective hydroformylation of natural olefins like eugenol, estragole, anethole, prenol and isoprenol using biphenyl based Buchwald phosphine ligands (S‐Phos ( L ₁ ), t‐Bu XPhos ( L ₂ ), Ru‐Phos ( L ₃ ), Johnphos ( L ₄ ) and DavePhos ( L ₅ ). Ru‐Phos ( L ₃ ) ligand exhibited high impact on the hydroformylation of eugenol providing high selectivity (90%) of linear aldehyde as major product. In addition, internal natural olefins like anethole and prenol provided moderate to high selectivity (65% and 85% respectively) of branched aldehydes as a major products. The various reaction parameters such as influence of ligands, P/Rh ratio, syngas pressure, temperature, time and solvents have been studied. A high activity and selectivity gained on the way to the linear aldehydes it may be due to the bulky, steric cyclohexyl and isopropoxy groups present in L ₃ phosphine ligand. Moreover, this catalytic system was smoothly converting natural olefins into corresponding linear and branched aldehydes with higher selectivity under the mild reaction conditions.     

Colloidal Dispersion of Nano-Ru/SiO2 in PEG and its Application for Hydrogenation of Benzene

The conversion of benzene to cyclohexane, a key intermediate in adipic acid production, is still the most important industrial hydrogenation reaction of monocyclic arenes. Traditionally, benzene hydrogenation is performed with heterogeneous catalysts such…     

New strategy for production of primary alcohols from aliphatic olefins by tandem cross-metathesis/hydrogenation

Primary alcohols are widely used in industry as solvents and precursors of detergents.The classic methods for hydration of terminal alkenes always produce the Markovnikov products.Herein,we reported a reliable approach to produce primary alcohols from terminal alkenes combining with biomass-derived allyl alcohol by tandem cross-metathesis/hydrogenation.A series of primary alcohol with different chain lengths was successfully produced in high yields(ca.90%).Computational studies revealed that self-metathesis and hydrogenation of substrates are accessible but much slower than crossmetathesis.This new methodology represents a unique alternative to primary alcohols from terminal alkenes.     

The Synthesis of Quinazolinones from Olefins,CO, and Amines over a Heterogeneous Ru‐clusters/Ceria Catalyst

Quinazolinones, an important class of heterocyclic compounds, have been widely used in pharmaceuticals because of their biological activity. However, the efficient and economical synthesis of quinazolinones has remained a challenge. A novel synthetic approach has now been developed to produce quinazolinones from olefins, CO, and amines over heterogeneous Ru‐clusters/ceria catalyst in the absence of acids, bases, and oxidants. Furthermore, H₂O is generated as the only by‐product. A series of quinazolinones with aromatic or non‐aromatic substituents can be obtained in yields of up to 99 %. The Ru‐clusters/ceria can be reused at least four times. The analysis of the E‐factor (environmental impact factor) for the synthesis of 2‐ethyl quinazolinone suggests that this system is more environmentally friendly than other processes reported previously.