Roles of the textural and surface chemical properties of activated carbon in the adsorption of acid blue dye

This study has demonstrated the use of empirical modeling in resolving the effects of individual carbon properties on acid blue dye adsorption. Acid blue dye adsorption tests were conducted on activated carbons prepared from bagasse by physical (CO2) and chemical (ZnCl2, MgCl2 and CaCl2) techniques. Empirical models based on the carbon textural (surface area and pore size) properties and the surface chemistry inferred from heteroatom (C,H, N, and S) concentration and carbon surface pH were used to resolve the effects of individual carbon properties on acid blue dye adsorption. This form of analysis was conducted to optimize carbon preparation properties, forming the foundation for tailor-making adsorbents from bagasse suitable for acid dye adsorption. A series of statistical analyses (partial F-tests to establish the parameter significance) measured variants including the mean square error, r2 and adjusted r2, normality, and randomness of residuals, and formed the basis for testing the adequacy of these models. The empirical models suggest that a combination of suitable pore structure and distinct basic surface chemistry generated by sulfur- and nitrogen-based groups, which were also elucidated by Fourier transform infrared spectroscopy, is necessary to promote acid dye adsorption.     

The Use of High Surface Area Mesoporous-Activated Carbon from Longan Seed Biomass for Increasing Capacity and Kinetics of Methylene Blue Adsorption from Aqueous Solution

Microporous- and mesoporous-activated carbons were produced from longan seed biomass through physical activation with CO₂ under the same activation conditions of time and temperature. The specially prepared mesoporous carbon showed the maximum porous properties with the specific surface area of 1773 m²/g and mesopore volume of 0.474 cm³/g which accounts for 44.1% of the total pore volume. These activated carbons were utilized as porous adsorbents for the removal of methylene blue (MB) from an aqueous solution and their effectiveness was evaluated for both the adsorption kinetics and capacity. The adsorption kinetic data of MB were analyzed by the pseudo-first-order model, the pseudo-second-order model, and the pore-diffusion model equations. It was found that the adsorption kinetic behavior for all carbons tested was best described by the pseudo-second-order model. The effective pore diffusivity (D_e) derived from the pore-diffusion model had the values of 4.657 × 10⁻⁷–6.014 × 10⁻⁷ cm²/s and 4.668 × 10⁻⁷–19.920 × 10⁻⁷ cm²/s for the microporous- and mesoporous-activated carbons, respectively. Three well-known adsorption models, namely the Langmuir, Freundlich and Redlich–Peterson equations were tested with the experimental MB adsorption isotherms, and the results showed that the Redlich–Peterson model provided the overall best fitting of the isotherm data. In addition, the maximum capacity for MB adsorption of 1000 mg/g was achieved with the mesoporous carbon having the largest surface area and pore volume. The initial pH of MB solution had virtually no effect on the adsorption capacity and removal efficiency of the methylene blue dye. Increasing temperature over the range from 35 to 55 °C increased the adsorption of methylene blue, presumably caused by the increase in the diffusion rate of methylene blue to the adsorption sites that could promote the interaction frequency between the adsorbent surface and the adsorbate molecules. Overall, the high surface area mesoporous carbon was superior to the microporous carbon in view of the adsorption kinetics and capacity, when both carbons were used for the removal of MB from an aqueous solution.     

几种植物基活性炭材料的表面结构与吸附性能比较——(II)表面化学结构与吸附性能研究

用X-射线光电子能谱对3种植物基活性炭材料:椰壳活性炭 (CAC4)、剑麻茎基活性炭(SSAC)和剑麻基活性碳纤维 (SACF) 的表面化学结构进行了表征,并研究和对比了它们的吸附性能,包括对碘、苯酚和亚甲基蓝的液相吸附性能,对有机蒸汽的吸附性能以及对Au3+的还原吸附性能等。结果表明,3个样品表面均含有多种含氧官能团,吸附能力SACF>SSAC> CAC4。样品的吸附性能主要取决于自身孔结构,与其表面化学结构也有密切的关系。     

Preparation of highly porous carbon from fir wood by KOH etching and CO2 gasification for adsorption of dyes and phenols from water

Fir wood was first carbonized for 1.5 h at 450 degrees C, then soaked in a KOH solution KOH/char ratio of 1, and last activated for 1 h at 780 degrees C. During the last hour CO2 was poured in for further activation for 0, 15, 30, and 60 min, respectively. Carbonaceous adsorbents with controllable surface area and pore structure were chemically activated from carbonized fir wood (i.e., char) by KOH etching and CO2 gasification. The pore properties, including the BET surface area, pore volume, pore size distribution, and pore diameter, of these activated carbons were first characterized by the t-plot method based on N2 adsorption isotherms. Fir-wood carbon activated with CO2 gasification from 0 to 60 min exhibited a BET surface area ranging from 1371 to 2821 m2 g(-1), with a pore volume significantly increased from 0.81 to 1.73 m2 g(-1). Scanning electron microscopic (SEM) results showed that the surfaces of honeycombed holes in these carbons were significantly different from those of carbons without CO2 gasification. The adsorption of methylene blue, basic brown 1, acid blue 74, p-nitrophenol, p-chlorophenol, p-cresol, and phenol from water on all the carbons studied was examined to check their chemical characteristics. Adsorption kinetics was in agreement with the Elovich equation, and all equilibrium isotherms were in agreement with the Langmuir equation. These results were used to compare the Elovich parameter (1/b) and the adsorption quantity of the unit area (q(mon)/Sp) of activated carbons with different CO2 gasification durations. This work facilitated the preparation of activated carbon by effectively controlling pore structures and the adsorption performance of the activated carbon on adsorbates of different molecular forms.     

Comparisons of porous and adsorption properties of carbons activated by steam and KOH

In this work, fir woods and pistachio shells were used as source materials to prepare porous carbons, which were activated by physical (steam) and chemical (KOH) methods. Pore properties of these activated carbons including the BET surface area, pore volume, pore size distribution, and pore diameter were first characterized by a t-plot method based on N(2) adsorption isotherms. Highly porous activated carbons with BET surface area up to 1009-1096 m(2)/g were obtained. The steam and KOH activation methods produced carbons with mesopore content in the range 9-15 and 33-49%, respectively. The adsorption equilibria and kinetics of tannic acid, methylene blue, 4-chlorophenol, and phenol from water on such carbons at 30 degrees C were then investigated to check their chemical characteristics. The Freundlich equation gave a better fit to all adsorption isotherms than the Langmuir equation. On the other hand, the intraparticle diffusion model could best follow all adsorption processes. In comparison with KOH-activated carbons, it was shown that the rate of external surface adsorption with steam-activated carbons was significantly higher but the rate of intraparticle diffusion was much lower.     

Adsorption Behaviors of CO2 and NH3 on Chemically Surface-Treated Activated Carbons

The adsorption characteristics of activated carbon treated with 30 wt% HCl and 30 wt% NaOH were investigated. The acid and base values were determined by Boehm's method and the surface structures were studied by the BET method with N2 adsorption and iodine adsorption capacity. Also the adsorption properties of the activated carbons treated with acid and base chemical solutions were investigated with CO2 and NH3 adsorptions. Different adsorption behaviors of CO2 and NH3 on the modified activated carbons were observed, even though the physical surfaces of the activated carbons (i.e., specific surface area, pore size, and pore volume) were not significantly changed. Copyright 1999 Academic Press.     

Comparative study for the removal of methylene blue via adsorption and photocatalytic degradation

Physically and chemically activated carbons were prepared from date pits and olive stones. Titania and WO(x)-TiO(2)/MCM-41 were prepared as photoactive catalysts. Surface characterizations were investigated from ash content, pH, base neutralization capacities and FT-IR techniques. The textural characteristics, namely specific surface area (S(BET)) and pore texture, were determined from low temperature adsorption of N(2) at 77 K. The decolorization of aqueous solution of methylene blue was performed by means of two alternative methods. Steam-activated carbons own higher surface area compared with ZnCl(2)-activated carbons, and the micropore surface area represents the major contribution of the total area. Steam-activated carbons were the most efficient decolorizing adsorbents owing to its higher surface area, total pore volume and the basic nature of the surface. The calculated values of DeltaG(0), DeltaH(0) and DeltaS(0) indicate the spontaneous behavior of adsorption. The photocatalytic degradation is more convenient method in decolorizing of methylene blue compared with the adsorption process onto activated carbons.     

Sulfur fixation on bagasse activated carbon by chemical treatment and its effect on acid dye adsorption

Heteroatoms are known to introduce specific surface functionalities that can enhance the adsorption properties of carbons. Sulfur fixation on bagasse-activated carbon was conducted by a low temperature chemical treatment with sulfuric acid followed by physical activation with CO₂ at 900?°C. The effect of sulfur fixation on the surface chemical properties of bagasse-activated carbons were investigated and on their subsequent acid dye removal (CIBA AB80) behavior. Surface chemical development were examined and followed using Fourier transform infrared spectroscopy (FTIR), heteroatom analysis and carbon surface acidity. Functional group stability with thermal treatment was also investigated. The textural properties of the activated carbons were characterized by nitrogen adsorption. Chemical pre-treatment and gasification was able to fix up to 0.2 wt% of sulfur on the activated carbon. Although the sulfur fixed by chemical treatment is low, this method introduced several advantages in comparison to fixation by thermal methods. The chemical method did not interfere with the textural development of the carbon, as found in thermal methods. In addition, the surface chemistry generated by these levels of sulfur groups was sufficient to increase the uptake of acid blue dyes by more than 700% based on adsorption capacities normalized by the surface area of the carbon.     

KOH活化木屑生物炭制备活性炭及其表征

以木屑热裂解的生物质炭为原料,氢氧化钾为活化剂,采用化学活化法制备活性炭,探讨了碱炭比、活化温度和活化时间对活性炭吸附亚甲基蓝吸附值的影响。 利用N2吸附实验、XRD和FTIR等实验技术,对原料与制备活性炭的结构与性能进行了表征。 结果表明,在碱炭质量比为1.5、活化温度750 ℃、活化时间2 h的条件下,所制备的活性炭对亚甲基蓝吸附值为255 mg/g,BET总比表面积为1514 m2/g,中孔比表面积为110 m2/g,吸附总孔容为0.821 cm3/g,中孔孔容为0.117 cm3/g,吸附平均孔径为2.170 nm。     

Preparation and characterization of activated carbon from bagasse fly ash

Activated carbons from bagasse fly ash (BFA) were prepared by one step chemical activation using ZnCl₂ as activating agent, or combination method of chemical with CO₂ physical activation (physicochemical activation). The development of porosity was studied in correlation with the method of activation, activation temperature, and also the chemical weight ratio. A typical sample by the combination method at 600 °C and weight ratio of ZnCl₂:BFA = 2 exhibited micropore volume of 0.528 cc/g, mesopore volume of 0.106 cc/g and surface area of 1200 m²/g. For determining the adsorption capacity of the carbon samples in solutions, phenol and methylene blue equilibrium adsorption experiments were conducted. The properties and adsorption capacity of the synthesized activated carbons has been compared to commercial activated carbon (Norit^® SX Plus).     

Adsorption of lignite-derived humic acids on coal-based mesoporous activated carbons

The adsorption by a coal-based mesoporous activated carbon of humic acids (HAs) isolated from two Polish lignites was studied. For comparison, a commercial Aldrich humic acid was also included into this study. The differences in chemical structure and functional groups of HAs were determined by elemental analysis and infrared spectroscopy DRIFT. Two activated carbons used differed in terms of mesopore volume, mesopore size distribution, and chemical properties of the surface. The kinetics of adsorption of HAs have been discussed using three kinetic models, i.e., the first-order Lagergren model, the pseudo-second-order model, and the intraparticle diffusion model. It was found that the adsorption of HAs from alkaline solution on mesoporous activated carbon proceeds according to the pseudo-second-order model. The correlation coefficients were close to 1. The intraparticle diffusion of HA molecules within the carbon particle was identified to be the rate-limiting step. Comparing the two activated carbons, the carbon with a higher volume of pores with widths of 10-50 nm showed a greater removal efficiency of HA. An increase in the Freundlich adsorption capacity with decreasing carbon content of HA was observed. Among the HAs studied, S-HA shows characteristics indicating the highest contribution of small-size fraction. The S-HA was removed by both activated carbons to the highest extent. The effect of pH solution on the adsorption of HA was examined over the range pH 5.4-12.2. It was found that the extent of adsorption decreased with decreasing pH of the solution.     

Adsorption of sodium dodecylbenzenesulfonate on activated carbons: effects of solution chemistry and presence of bacteria

The objective of the present investigation was to determine the effectiveness of activated carbon in removing sodium dodecylbenzenesulfonate (SDBS) and to analyze the chemical and textural characteristics of the activated carbons that are involved in the adsorption process. Studies were also performed on the influence of operational variables (pH, ionic strength, and presence of microorganisms) and on the kinetics and interactions involved in the adsorption of this pollutant on activated carbon. The kinetics study of SDBS adsorption revealed no problems in its diffusion on any of the activated carbons studied, and Weisz-Prater coefficient (C WP) values were considerably lower than unity for all activated carbons studied. SDBS adsorption isotherms on these activated carbons showed that: (i) adsorption capacity of activated carbons was very high (260-470 mg/g) and increased with larger surface area; and (ii) dispersive interactions between SDBS and carbon surface were largely responsible for the adsorption of this pollutant. SDBS adsorption was not significantly affected by the solution pH, indicating that electrostatic adsorbent-adsorbate interactions do not play an important role in this process. The presence of electrolytes (NaCl) in the medium favors SDBS adsorption, accelerating the process and increasing adsorption capacity. Under the working conditions used, SDBS is not degraded by bacteria; however, the presence of bacteria during the process accelerates and increases SDBS adsorption on the activated carbon. Microorganism adsorption on the activated carbon surface increases its hydrophobicity, explaining the results observed.     

Rice husk ash as an adsorbent for methylene blue—effect of ashing temperature

Utilization of one waste material to control pollution caused by another is of high significance in the remediation of environmental problems. Rice husk, an abundantly available agricultural waste, can be used as a low cost adsorbent for dyes and heavy metals in effluent streams. The possible utilization of rice husk ash as an adsorbent for methylene blue dye from aqueous solutions has been investigated. Ash samples from husks of two origins were prepared at different temperatures and their physical, chemical spectroscopic and morphological properties were determined. XRD, FTIR and SEM were some of the techniques adopted for the characterization. The samples were also analyzed for bulk density, pH, nitrogen adsorption properties and lime reactivity. Experiments of methylene blue adsorption on the ash samples were conducted using batch technique and a comparative study was made. Results were analyzed using linear, Langmuir and Freundlich isotherms. The values of separation factor indicate that most of the ash samples do adsorb the dye molecules, but in varying quantities. Calcination at 900^∘C reduces the adsorption capacity of the ash to a great extent. Regression analysis shows that the experimental data fits both Langmuir and Freundlich isotherms for certain concentration limits. The adsorbate species are most probably transported from the bulk of the solution into the solid phase through intra-particle diffusion process. Kinetics of adsorption was found to follow pseudo second order rate equation with R ²∼ 0.99. The highest adsorption capacity (Q ₀) achieved is found to be ∼690 mg/g, which is even higher than the values reported for activated carbon from rice husk. The adsorption capacity of the ash samples are in good agreement with their surface area and pore volume.     

Adsorption characteristics of activated carbons obtained from corncobs

Dried, crushed, corncobs were carbonized at 500°C and steam activated (in one- or two-step schemes), or activated with H₃PO₄. The products were characterized by N₂ adsorption at 77 K, using the BET, _s and DR methods. Adsorption capacity was demonstrated by the iodine and phenol numbers, and the isotherms of methylene blue and Pb²⁺ ions, from aqueous solutions. A distribution of porosity in the carbons was estimated within the various ranges (ultra-, super-, meso- and macropores). Simple carbonization yields a poor adsorbing carbon; only its uptake for iodine was high and proposed to be due to an addition reaction on residual unsaturation of the parent lignocellulosic structures. Enhanced porosity was best associated with chemical activation and/or steam pyrolysis at 700°C. These activated carbons proved highly porous and rich in mesopores, and showed high adsorption capacity for methylene blue and Pb²⁺ ions. Phenol uptake was found to depend on surface chemical nature of the carbon rather than its porous properties. Corncobs were postulated to be feasible as feedstock to produce good adsorbing carbons, under the one-step activation schemes outlined here.     

微波辐射紫茎泽兰制备优质活性炭的研究

以紫茎泽兰为原料,碳酸钾为活化剂,采用超声波浸渍,微波辐射法制备活性炭.研究了浸渍方式与时间、微波功率、微波辐射时间、剂料比对活性炭吸附性能和得率的影响.得到了本实验条件下的优化工艺条件:超声波浸渍20min、120℃脱水2h,微波功率700W、微波辐射时间12min、剂料比1.25∶1.优化工艺条件下制备的活性炭碘吸附值为1470.27mg/g,亚甲基蓝吸附值为300mL/g,得率为16.35%.浸渍时间极大的缩短,微波辐射时间只有传统法活化时间的1/15左右,活性炭的吸附指标超过了国标GB/T 13803.1-1999和GB/T 13803.2-1999一级品的标准,其中碘吸附值是国家一级标准的1.47倍,亚甲基蓝吸附值是国家一级标准的2.73倍.同时,测定了该活性炭氮吸附,其BET比表面积为1540.97m2/g,总孔容为0.7393mL/g,并通过DFT表征了活性炭的孔径分布,结果表明该活性炭为微孔型活性炭.     

Absorption of phenol and methylene blue by activated carbon from pecan shells

Activated carbon is produced from pecan shells by chemical activation using phosphoric acid. This activation is followed by the treatment with sodium dodecyl sulfate to prepare the surface for the adsorption of phenol and methylene blue from aqueous solution. The results showed a great ability for methylene blue removal with sorption capacity of 410 mg/g at pH 9 and solution concentration of 35 mg/l, while moderate adsorption was obtained for phenol with a capacity of 18 mg/g at pH 11 and the same solution concentration. The increase or decrease in solution pH has a favorable effect on the sorption of both adsorbates. Langmuir and Freundlich models were used to fit the experimental data. The text was submitted by the authors in English.     

Pore structure and adsorption performance of the KOH-activated carbons prepared from corncob

Carbonaceous adsorbents with controllable surface area were chemically activated with KOH at 780 degrees C from chars that were carbonized from corncobs at 450 degrees C. The pore properties, including BET surface area, pore volume, pore size distribution, and mean pore diameter of these activated carbons, were characterized by the t-plot method based on N(2) adsorption isotherms. Two groups are classified according to the types of adsorption/desorption isotherms. Group I corncob-derived activated carbons, with KOH/char ratios from 0.5 to 2, exhibited BET surface area ranging from 841 to 1221 m(2)/g. Group II corncob-derived activated carbons, with KOH/char rations from 3 to 6, showed high BET surface areas, from 1976 to 2595 m(2)/g. From scanning electron microscopic (SEM) results, the surface morphology of honeycombed holes on corncob-derived activated carbons was significantly influenced by the KOH/char ratios. The adsorption kinetics of methylene blue, basic brown 1, acid blue 74, 2,4-dichlorophenol, 4-chlorophenol, and phenol from water at 30 degrees C were studied on the two groups of activated carbons, which were suitably described by two simplified kinetic models, pseudo-first-order and pseudo-second-order equations. The effective particle diffusivities of phenols and dyes at the corncob-derived activated carbons of group II are higher than those of ordinary activated carbons. The high-surface-area activated carbons were demonstrated to be promising adsorbents for pollution control and for other applications.     

Estimation of structural and sorption characteristics of activated bentonite

The influence of concentration, solution pH, and temperature on the adsorption of a cationic surfactant on activated bentonite is studied. It is shown that changes in the chemical properties of the surface of the mineral promote variations in its sorption characteristics with respect to methylene blue and do not affect significantly the sorption of phenol.     

Unburned carbon as a low-cost adsorbent for treatment of methylene blue-containing wastewater

Fly ash, natural zeolite, and unburned carbon separated from fly ash have been employed as low-cost adsorbents for dye adsorption in methylene blue-containing wastewater. It is found that the unburned carbon exhibits a much higher adsorption capacity than raw fly ash and natural zeolite. The adsorption capacities of fly ash, natural zeolite, and unburned carbon for methylene blue are 2 x 10(-5), 5 x 10(-5), and 2.5 x 10(-4) mol/g, respectively. Investigation also indicates that adsorption is influenced by initial dye concentration, particle size, dye solution pH, and adsorption temperature. Adsorption on unburned carbon increases with the initial dye concentration, solution pH, and temperature, but reduces with the increasing particle size. Kinetic studies show that adsorption of methylene blue on fly ash, natural zeolite, and unburned carbon can be best described by the pseudo-second-order adsorption model and that adsorption is a two-step diffusion process. The apparent activation energies for methylene blue adsorption on unburned carbon in the first and second diffusion processes are 12.4 and 39.3 kJ/mol, respectively.     

有序介孔炭的合成及液相有机大分子吸附性能研究

分别采用有序介孔氧化硅SBA-15和NaY分子筛为硬模板合成了系列有序介孔炭OMC和微孔炭CFY. N₂静态吸附测试表明, 所合成的介孔炭具有丰富的介孔结构和集中的介孔分布. 以亚甲基蓝为探针分子, 研究其在有序介孔炭OMC和微孔炭CFY上的吸附行为. 研究结果表明, 有序介孔炭中大于3.5 nm的大介孔孔容是决定亚甲基蓝吸附容量和吸附速率的关键因素. 吸附动力学理论研究表明, 准二级动力学方程可以很好地描述亚甲基蓝分子在介孔炭上吸附动力学行为.