Amperometric determination of paracetomol by a surface modified cobalt hexacyanoferrate graphite wax composite electrode

A stable electro active thin film of cobalt hexacyanoferrate (CoHCF) was deposited on the surface of an amine adsorbed graphite wax composite electrode using a simple method. Cyclic voltammetric experiments showed two pairs of well defined peaks for this CoHCF modified electrode which exhibited excellent electrocatalytic property for the oxidation of paracetomol at a reduced overpotential of 100 mV and over a concentration range of 3.33 × 10⁻⁶ to 1.0 × 10⁻³ M with a slope of 0.208 μA/μM with good sensitivity. The influence of the supporting electrolyte on peak current and peak potential were also obtained in addition with effects of common interference (e.g., ascorbic acid) on the response of the modified electrode. Various parameters that influence the electrochemical behavior of the modified electrode were optimized by varying scan rates and pH. Electrochemical impedance spectroscopy studies suggested that the electrode reaction of the CoHCF film is mainly controlled by transport of counter ion. The immobilized CoHCF maintained its redox activity showing a surface controlled electrode reaction with the electron transfer rate constant (K_s) of 0.94 s⁻¹ and charge transfer coefficient of 0.42. Hydrodynamic and chronoamperometric studies were done to explore the utility of the modified electrode in dynamic systems. The results of the differential pulse voltammetry (DPV) using the modified electrode was applied for the determination of paracetomol in commercially available tablets. The results obtained reveal that the electrode under study could be used as an effective sensor for online monitoring of paracetomol.     

Simultaneous determination of butylated hydroxyanisole (BHA) and butylated hydroxytoluene (BHT) in food samples using a carbon composite electrode modified with Cu3(PO4)2 immobilized in polyester resin

A simple electrochemical method was developed for the single and simultaneous determination of butylated hydroxyanisole (BHA) and butylated hydroxytoluene (BHT) in food samples using square-wave voltammetry (SWV). A carbon composite electrode modified (MCCE) with copper (II) phosphate immobilized in a polyester resin was proposed. The modified electrode allowed the detection of BHA and BHT at potentials lower than those observed at unmodified electrodes. A separation of about 430 mV between the peak oxidation potentials of BHA and BHT in binary mixtures was obtained. The calibration curves for the simultaneous determination of BHA and BHT demonstrated an excellent linear response in the range from 3.4 × 10⁻⁷ to 4.1 × 10⁻⁵ mol L⁻¹ for both compounds. The detection limits for the simultaneous determination of BHA and BHT were 7.2 × 10⁻⁸ and 9.3 × 10⁻⁸ mol L⁻¹, respectively. In addition, the stability and repeatability of the electrode were determined. The proposed method was successfully applied in the simultaneous determination of BHA and BHT in several food samples, and the results obtained were found to be similar to those obtained using the high performance liquid chromatography method with agreement at 95% confidence level.     

Preparation of a cobalt hexacyanoferrate film-modified aluminum electrode by chemical and electrochemical methods: enhanced stability of the electrode in the presence of phosphate and ruthenium(III)

Modification of an aluminum electrode by means of a thin film of cobalt hexacyanoferrate (CoHCF) using electroless and electrochemical procedures is described. The modification conditions of the aluminum surface, including the electroless deposition of metallic cobalt on the electrode surface from CoCl₂+NaF solution and the chemical derivatization of the deposited cobalt to give a CoHCF film in 0.25 M KCl+0.25 M K₃[Fe(CN)₆] solution, have been determined. The modified Al electrodes prepared under optimum conditions show one or two well-defined redox couples in phosphate buffer solutions of pH 7.2, depending on the preparation procedure, due to the [Co^IIFe^III/II(CN)₆]^–/2– system. The effect of pH, alkali metal cations, and anions of the supporting electrolyte on the electrochemical characteristics of the modified electrode were studied. Diffusion coefficients of hydrated Na⁺ in the film, the transfer coefficient, and the transfer rate constant for electrons were determined. The stability of the modified electrodes under various experimental conditions was studied and their high stability in the sodium phosphate buffer solutions was confirmed. Enhanced stability was observed when the modified electrode was scanned in fresh solutions of RuCl₃ between 0 and 1 V for at least 20 cycles, due to the formation of mixed hexacyanoferrates of cobalt and ruthenium. Electronic Publication     

Solid-phase ultraviolet absorbance spectrophotometric multisensor for the simultaneous determination of butylated hydroxytoluene and co-existing antioxidants

Continuous flow injection and UV spectrophotometric detection have been proposed for simultaneous determination of the two binary mixtures, butylated hydroxytoluene (BHT)/n-propyl gallate (n-PG) and butylated hydroxytoluene (BHT)/butylated hydroxyanisole (BHA), in food and cosmetics samples. The method is based on the different residence times of each antioxidant when the flow cell is packed to a height of 25 mm with silica C₁₈ using methanol-water 50:50% (v/v) as a carrier with a flow rate of 1.25 and 1.10 ml min⁻¹, respectively. The determination of each antioxidant is based on the measurement of its absorbance at its maximum wavelengths using a DAD detector at 30 and 180 s for the mixture n-PG-BHT and 90 and 220 s for BHA-BHT. Calibration graphs were linear over the range 10.0-300.0 μg ml⁻¹ for each antioxidant in both mixtures. The relative standard deviations were 2.5% for BHT and 2.0% for the co-existing antioxidant. Resolution of the n-PG-BHT mixture in ratios between 1:8 and 8:1 and the BHA-BHT mixture in ratios between 1:10 and 10:1 is possible. The method was applied to the determination of both antioxidants in fat foods and cosmetics samples with recoveries ranging between 101 and 105%.     

Voltammetric determination of N-acetylcysteine using a carbon paste electrode modified with copper(II) hexacyanoferrate(III)

The preparation and electrochemical characterization of a carbon paste electrode modified with copper(II) hexacyanoferrate(III) (CuHCF) as well as its behavior as electrocatalyst toward the oxidation of N-acetylcysteine were investigated. The electrochemical behavior of the modified electrode and the electrooxidation of N-acetylcysteine were explored using sweep linear voltammetry. The best voltammetric response was observed for a paste composition of 20% (w/w) copper(II) hexacyanoferrate(III) complex, acetate buffer solution at pH of 6.0 as the electrolyte and scan rate of 10 mV s^− 1. A linear voltammetric response for N-acetylcysteine was obtained in the concentration range from 1.2 × 10^− 4 to 8.3 × 10^− 4 mol L^− 1, with a detection limit of 6.3 × 10^− 5 mol L^− 1. The proposed electrode is useful for the quality control and routine analysis of N-acetylcysteine in pharmaceutical formulations.     

Determination of hydrogen peroxide by utilizing a cobalt(II)hexacyanoferrate-modified glassy carbon electrode as a chemical sensor

A mixed-valence cluster of cobalt(II)hexacyanoferrate possesses an electron transfer property and is suitable for the development of an effective hydrogen peroxide detection scheme. The characteristics of cobalt(II)hexacyanoferrate have been studied using both elemental analysis and infrared spectra, confirming the structure is Co[Fe^II(CN)₆]. The cobalt(II)hexacyanoferrate-modified electrode exhibits a rapid response (t_95% - 6.5 s) to the injection of 5.0 × 10⁻⁵ M hydrogen peroxide. The linearity of the response is up to 1.1 × 10⁻³ M (correlation coefficients is 0.999). The sensitivity of this modified electrode is 11.8 μA/mM-mm². The detection limit of cobalt(II)hexacyanoferrate-modified electrode to hydrogen peroxide is 6.25 × 10⁻⁸ M. The current chemical sensor modified with Co[Fe^II(CN)₆] has better sensitivity than previous ones. The modified glassy carbon electrode shows no interference from ascorbic acid, uric acid, acetaminophen, 1,4-dihydroxyquinone, dopamine at the 2.0 × 10⁻⁴ M level and polyamines at 5.0 × 10⁻⁵ M level.     

Physical immobilization of laccase on an electrode by means of poly(ethyleneimine) microcapsules

Microcapsules of poly(ethyleneimine) were used to immobilize laccase on the surface of an electrode and its mediated electron transfer was studied with the redox mediator p-phenylenediamine (PPD). The microcapsules consisted of a cross-linked PEI wall generated from an emulsion of an aqueous phase containing the enzyme. The reaction of encapsulated laccase with PPD was studied by spectrophotometry and oxygen consumption. We found that the encapsulation resulted in a small shift for the optimum pH and a lower K_m value when compared to free laccase. These differences are attributed to the charged micro-environment offered by the microcapsules. The microcapsules were then deposited on a glassy carbon electrode and chronoamperometry was used to evaluate the mediated electron transfer between the enzyme and the electrode. No significant differences in term of optimum pH and K_m occurred upon capsules deposition on the electrode. The response time of the electrode for PPD oxidation was higher than those found in the literature, which suggests that the PEI capsule wall offers some resistance to mediator permeation, an hypothesis that was verified by RDE measurements. The charged nature of the PEI membrane appeared to affect several parameters of the laccase-mediator reaction and the effect of pH and mediator charge on this reaction are reported. The immobilization platform under study can be applied to different enzyme-mediator systems than the laccase-PPD used here and is relevant to the development of bioelectrocatalytic systems.     

Voltammetric sensor for nitrite determination based on its electrocatalytic reduction at the surface of p-duroquinone modified carbon paste electrode

A p-duroquinone (tetramethyl-p-benzoquinone) modified carbon paste electrode (DMCPE) was employed to study the electrocatalytic reduction of nitrite in aqueous solutions using cyclic voltammetry (CV), double potential-step chronoamperometry, and differential pulse voltammetry (DPV). It has found that under an optimum condition (pH 1.00), the reduction of nitrite at the surface of DMCPE occurs at a potential of about 660 mV less negative than that of an unmodified carbon paste electrode (CPE). The catalytic rate constant, k′_h, based on Andrieux and Saveant theoretical model was calculated as for scan rate 10 mV s^-1. Also, the apparent diffusion coefficient, D _app, was found as 2.5 × 10^–10 and 3.61 × 10^–5 cm² s^-1 for p-duroquinone in carbon paste matrix and nitrite in aqueous buffered solution, respectively. The values for αn_α were estimated to be −0.65 and −0.19 for the reduction of nitrite at the surface of DMCPE and CPE, respectively. The electrocatalytic reduction peak currents showed a linear dependence on the nitrite concentration, and a linear analytical curve was obtained in the ranges of 5.0 × 10^–5 M to 8.0 × 10^–3 M and 6.0 × 10^–6 M to 8.0 × 10^–4 M of nitrite concentration with CV and DPV methods, respectively. The detection limits (2σ) were determined as 2.5 × 10^–5 M and 4.3 × 10^–6 M by CV and DPV methods. This method was also applied as a simple, selective and precise method for determination of nitrite in real samples (the weak liquor from the wood and paper factory of Mazandaran province in Iran) by using a standard addition method.     

Ligational behaviour of thiosemicarbazide and thiosemicarbazone-(III): Tetragonal complexes of cobalt(II) derived from 4-benzylamidothiosemicarbazide and 1-(α-) furyl-4-benzylamidothiosemicarbazone

Zusammenfassung Es wurden eine Anzahl von neuen Kobalt(II)-Komplexen von 4-Benzylamidothiosemicarbazid (BTSC) und 1-(-)Furyl-4-benzylamidothiosemicarbazon (FBTS) von der allgemeinen Zusammensetzung CoL ₂ X ₂ (L=BTSC, FBTS;X=Cl, Br, I, NO₃ and NCS) synthetisiert. Die Untersuchugen erfolgten mittels Elementaranalyse, magnetischer Messungen, Elektronenanregungsspektroskopie und IR-Spektroskopie (einschließlich des fernen IR); aus diesen Messungen ließ sich eine im wesentlichen tetragonale Symmetrie für alle Komplexe dieser Reihe ableiten.

---

Ligational behaviour of thiosemicarbazide and thiosemicarbazone-(III): Tetragonal complexes of cobalt(II) derived from 4-benzylamidothiosemicarbazide and 1-(-) furyl-4-benzylamidothiosemicarbazone

A number of new complexes of cobalt(II) have been prepared with 4-benzylamidothiosemicarbazide (BTSC) and 1-(-)furyl-4-benzylamidothiosemicarbazone (FBTS) which conform to the general formula CoL ₂ X ₂ (whereL=BTSC andFBTS andX=Cl, Br, I, NO₃ and NCS). These have been characterized by chemical analyses and physical measurements. The tetragonal symmetry has been proposed on the basis of electronic spectral studies for all these complexes. The explanation for the slightly lower magnetic moments for cobalt(II) complexes has been sought in the possible presence of low symmetry component. The tetragonal radial parametersDq(E),Dq(A),Dt andDs and molecular orbital parameters d and d have been evaluated. The S–N, bidentate nature of the ligands and the presence of the various anions in the coordination sphere have been confirmed on the basis of additional Co–N, Co–S and Co–X frequencies in the far infrared spectra of the complexes. The nitrato and thiocyanato groups act as monodentate and are coordinated through oxygen and nitrogen atoms, respectively.

     

A novel amperometric sensor for the detection of difenidol hydrochloride based on the modification of Ru(bpy)3 on a glassy carbon electrode

An amperometric sensor for the detection of difenidol, a tertiary amine-containing analyte, was proposed. Ruthenium(II) tris(bipyridine)/multi-walled carbon nanotubes/Nafion composite film was suggested to modify the glassy carbon electrode. The modified electrode was shown to be an excellent amperometric sensor for the detection of difenidol hydrochloride. The linear range is from 1.0 × 10⁻⁶ to 3.3 × 10⁻⁵ M with a correlation coefficient of 0.998. The limit of detection was 5 × 10⁻⁷ M, which was obtained through experimental determination based on a signal-to-noise ratio of three. The sensor was employed to the determination of the active ingredients in the tablets containing difenidol hydrochloride.     

An efficient aerobic oxidation for p -xylene to p -toluic acid catalyzed by cobalt (II) hydroxamates with benzo-15-crown-5

Cobalt (II) hydroxamates with the benzo-15-crown-5 (B15C5) pendant have been synthesized and characterized. These complexes were successfully employed to the oxidation of p-xylene to p-toluic acid with air at 110°C under normal atmospheric pressure. The effects of the B15C5 pendant, the length of chain bonding of B15C5 in these complexes and the addition of alkali metal ions on the oxidation for p-xylene are also investigated by the comparison with the crown-free analogue.     

DNA/Poly(p-aminobenzensulfonic acid) composite bi-layer modified glassy carbon electrode for determination of dopamine and uric acid under coexistence of ascorbic acid

A nano-composite of DNA/poly(p-aminobenzensulfonic acid) bi-layer modified glassy carbon electrode as a biosensor was fabricated by electro-deposition method. The DNA layer was electrochemically deposited on the top of electropolymerized layer of poly(p-aminobenzensulfonic acid) (Pp-ABSA). Scanning electron microscopy, X-ray photoelectron spectroscopy and electrochemical impedance spectrum were used for characterization. It demonstrated that the deposited Pp-ABSA formed a 2-D fractal patterned nano-structure on the electrode surface, and which was further covered by a uniform thin DNA layer. Cyclic voltammetry and electrochemical impedance spectrum were used to characterize the deposition, and demonstrated the conductivity of the Pp-ABSA layer. The biosensor was applied to the detection of dopamine (DA) and uric acid (UA) in the presence of ascorbic acid (AA). In comparison with DNA and Pp-ABSA single layer modified electrodes, the composite bi-layer modification provided superior electrocatalytic actively towards the oxidation of DA, UA and AA, and separated the originally overlapped differential pulse voltammetric signals of UA, DA and AA oxidation at the bare electrode into three well-defined peaks at pH 7 solution. The peak separation between AA and DA, AA and UA was 176 mV and 312 mV, respectively. In the presence of 1.0 mM AA, the anodic peak current was a linear function of the concentration of DA in the range 0.19-13 microM. The detection limit was 88 nM DA (s/n=3). The anodic peak current of UA was also a linear function of concentration in the range 0.4-23 microM with a detection limit of 0.19 microM in the presence of 0.5 mM AA. The superior sensing ability was attributed to the composite nano-structure. An interaction mechanism was proposed.     

Hydride generation atomic absorption spectrometry with insitu graphite tube trapping for the determination of Se (IV) and Se (VI) in baltic sea water samples

This paper reports the results of an optimisation study for a procedure to determine the total selenium and its inorganic species, Se(IV) and Se(VI) using atomic absorption spectrometry combined with hydride generation and in-situ trapping of the analyte on the inner walls of the graphite tube. With the use of the proposed modification, a detection limit (3σ) of 0.018 ng/ml is achieved. This paper presents exemplary results, according to the proposed procedure, for selenium determination in samples of marine water. The concentrations of selenium in the samples ranged from <0.02 ng/ml to 0.16ng/ml of Se(IV) and from <0.02 ng/ml to 0.10 ng/ml of Se(VI).     

Development and characterization of an amperometric sensor for triclosan detection based on electropolymerized molecularly imprinted polymer

A novel amperometric sensor based on electropolymerized molecularly imprinted polymer (MIP) for triclosan detection is reported. The sensor was prepared by electropolymerizing o-phenylenediamine (o-PD) on a glassy carbon electrode in the presence of template triclosan. The template can be quickly removed by NaOH solution. After incubating in acetate buffer for 15 min, the sensor response sensitively to triclosan over a linear range of 2.0 × 10^{− 7} to 3.0 × 10^{− 6} mol/L and a detection limit as low as 8.0 × 10^{− 8} mol/L is obtained. This sensor provides an efficient way for eliminating interferences from compounds with similar structures to that of triclosan.     

Benzeneacetaldehyde-4-hydroxy-alpha-oxo-aldoxime as a new analytical reagent for the spectrophotometric determination of cobalt

Benzeneacetaldehyde-4-hydroxy-α-oxo-aldoxime is proposed as a new sensitive and selective reagent for the spectrophotometric determination of cobalt. The reagent reacts with cobalt in the pH range 8.6–9.4 to form a yellow colored 1:3 chelate which is very well extracted in chloroform. Beer's law is obeyed in the concentration range 0.05–1.3 μg ml⁻¹ cobalt. The molar absorptivity of the extracted species is 2.746×10⁴ l mol⁻¹ cm⁻¹ at 390 nm. The proposed method is highly sensitive, selective, simple, rapid, accurate and has been satisfactorily applied for the determination of cobalt in synthetic mixtures, pharmaceutical samples, biological samples and alloys.     

Simultaneous determination of N-acetyl-p-aminophenol and p-aminophenol with poly(3,4-ethylenedioxythiophene) modified glassy carbon electrode

A sensitive and selective method was developed for the determination of N-acetyl-p-aminophenol (APAP) and p-aminophenol (PAP) using poly(3,4-ethylenedioxythiophene) (PEDOT)-modified glassy carbon electrode (GCE). Cyclic voltammetry and differential pulse voltammetry were used to investigate the electrochemical reaction of APAP and PAP at the modified electrode. Both APAP and PAP showed quasireversible redox reactions with formal potentials of 367 mV and 101 mV (vs. Ag/AgCl), respectively, in phosphate buffer solution of pH 7.0. The significant peak potential difference (266 mV) between APAP and PAP enabled the simultaneous determination both species based on differential pulse voltammetry. The voltammetric responses gave linear ranges of 1.0 × 10⁻⁶-1.0 × 10⁻⁴ mol L⁻¹ and 4.0 × 10⁻⁶-3.2 × 10⁻⁴ mol L⁻¹, with detection limits of 4.0 × 10⁻⁷ mol L⁻¹ and 1.2 × 10⁻⁶ mol L⁻¹ for APAP and PAP, respectively. The method was successfully applied for the determination of APAP and PAP in pharmaceutical formulations and biological samples.     

Lichen-based biosensor for the determination of benzene and 2-chlorophenol: microcalorimetric and amperometric investigations

Preliminary microcalorimetric studies have been performed to analyse the response of a whole epiphytic lichen tissue (Evernia prunastri) to 2-chlorophenol (2Cl-), a pollutant of oil mill waste-water, in order to evaluate whether the tissue might be used to assess the toxic characteristics of polluted waters. The obtained results (lichen viability expressed in hours, enthalpy variations for the 2Cl-/lichen interactions) were used to create a lichen-based biosensor that uses an amperometric oxygen electrode (a Clark electrode) as a transducer. The lichen catalyses aromatic ring cleavage (via pyrocatechase enzymes present in the lichen), and transforms aromatic substances like 2Cl- into muconic acid (C₆H₆O₄). Following a full electroanalytical characterisation, the performance of the proposed lichen biosensor was compared to that of a biosensor based on Pseudomonas putida cells, which was originally constructed to monitor benzene in different matrices (water, air, petrol and oil) and was tested in our laboratory previously.     

Langmuir-Blodgett film of p-tert-butylthiacalix[4]arene modified glassy carbon electrode as voltammetric sensor for the determination of Hg(II)

The π-A isotherms and UV-vis spectra of the transferred films suggested that the monolayer of p-tert-butylthiacalix[4]arene can coordinate with Hg²⁺ at the air-water surface. From these observations, a glassy carbon electrode coated with Langmuir-Blodgett film of p-tert-butylthiacalix[4] arene as a new voltammetric sensor is designed for the determination of trace amounts of Hg²⁺. Compared with bare glassy carbon electrode and modified glassy carbon electrode using direct coating method, the Langmuir-Blodgett film-modified electrode can greatly improve the measuring sensitivity of Hg²⁺. Under the selected conditions, the Langmuir-Blodgett film-modified electrode in 0.1 mol L⁻¹ H₂SO₄ + 0.01 mol L⁻¹ KCl solution shows a linear voltammetric response for Hg²⁺ in the range of 5.0 × 10⁻¹⁰ to 1.5 × 10⁻⁷ mol L⁻¹, with a detection limit of 2.0 × 10⁻¹⁰ mol L⁻¹. The proposed method was also applied to determine Hg²⁺ in water samples (tap, lake and river water). In addition, the fabricated electrode exhibited a distinct advantage of simple preparation, non-toxicity, good reproducibility and good stability.     

Flow-injection solid surface lanthanide-sensitized luminescence sensor for determination of <Emphasis Type="Italic">p</Emphasis>-aminobenzoic acid

A single optosensing device based on lanthanide-sensitized luminescence was developed for determination of p-aminobenzoic acid (PABA). The method is based on the formation of a complex between PABA and Tb(III) immobilized on the solid phase (QAE A-25 resin) placed inside the flow cell. NaCl (1 M) was used as carrier solution and HCl (0.05 M) as eluent. The sample solutions of PABA (100 μL) containing Tb(III) and buffered at pH = 6.0 were injected into the carrier stream and the luminescence was measured at λ _ex = 290 nm and λ _em = 546 nm. The method shows a linear range from 0.2 to 6.0 μg mL⁻¹ with an RSD of 1.2% (n = 10) and a sampling frequency of 22 h⁻¹. A remarkable characteristic of the method is its high selectivity which allows it to be satisfactorily applied to the analysis of PABA in pharmaceutical samples without prior treatment. Figure Typical emission bands of Tb(III) in a solid-phase PABA–Tb(III) luminescence spectrum