定位生长法制备AFM单壁碳纳米管针尖

采用粘性胶状物作为生长单壁碳纳米管(SWNTs)的催化剂前驱体, 在原子力显微镜下驱动废旧的硅探针粘附该种胶状物,随后进行化学气相沉积(CVD), 实现了SWNTs在硅探针末端的定位生长, 成功地制备出了SWNT针尖. 对SWNTs及SWNT 针尖进行了表征, 并对针尖的稳定成像条件进行了分析. 结果表明, 针尖一般由5-10 nm 的SWNT 管束构成, 伸出长度仅为几百纳米, 受热振动影响较小, 无需后处理即可稳定地成像, 成像分辨率与新的硅探针相当.     

Electrocatalytic oxidation of formic acid on platinum particles dispersed in SWNT/PANI composite film

Single-walled carbon nanotube (SWNT)/Polyaniline (PANI) composite film with good dispersion was prepared by electropolymerization of aniline containing well-dissolved SWNTs. Platinum (Pt) particles were electrodeposited on the SWNT/PANI composite film subsequently. The presence of SWNTs and platinum in the composite film was confirmed by XRD analysis. Four-point probe investigation exhibits that the electrical conductivity of SWNT/PANI composite film is significantly higher than that of pure PANI film. Cyclic voltammogram and Chronoamperogram show that Pt-modified SWNT/PANI electrode performs higher electrocatalytic activity than Pt-modified pure PANI electrode toward formic acid oxidation.     

Electrochemical and conductivity measurements of single-wall carbon nanotube network electrodes

The electrochemical response of two-dimensional networks of pristine single-wall carbon nanotubes (SWNTs) has been investigated. SWNTs were grown by catalyzed chemical vapor deposition on an insulating SiO2 substrate, and then electrically contacted by lithographically defined Au electrodes. Subsequent insulation of the contact electrodes enabled the electrochemical properties of the SWNT network to be isolated and directly studied for the first time. The electrochemical activity of the SWNT network was found to be strongly dependent on the applied potential. For the same SWNT electrode, the limiting current for the oxidation of 5 mM Fe(phen)32+ was found to be much greater than expected based on the signal for the reduction of 5 mM Ru(NH3)63+. Simultaneous conductance and electrochemical measurements demonstrated decreasing conductance as the potential was scanned negative (versus Ag/AgCl) with the minimum conductance at around the reduction potential for Ru(NH3)63+. These results are consistent with the presence of both metallic and semiconducting SWNTs in the SWNT network electrode. Moreover, these results show that through appropriate choice of mediator and electrode potential, metallic SWNTs can be electrochemically addressed independently of semiconducting SWNTs.     

Atomic Force Microscopic and Electrochemical Investigations of an Electrostatically Fabricated Single‐Wall Carbon Nanotubes Modified Electrode

Single‐wall carbon nanotubes (SWNTs) sub‐monolayer film has been prepared by simply electrostatically adsorbing nanotubes onto a 2‐aminoethanethiol self‐assembled monolayer (SAM) on a gold bead electrode. Tapping‐mode atomic force microscopy (TM‐AFM) is used to characterize the SWNT film, which exhibits that the orientation of SWNTs on the SAM is horizontal and the surface coverage is quite low. The SWNTs modified electrode shows nearly ideal electrochemical response to Fe(CN) /Fe(CN) redox probe. The electrode with such a low SWNTs coverage, however, shows good electrocatalytic behavior to cytochrome c.     

Optical Properties of Single-Walled Carbon Nanotubes Separated in a Density Gradient; Length, Bundling, and Aromatic Stacking Effects

Single-walled carbon nanotubes (SWNTs) are promising materials for in vitro and in vivo biological applications due to their high surface area and inherent near infrared photoluminescence and Raman scattering properties. Here, we use density gradient centrifugation to separate SWNTs by length and degree of bundling. Following separation, we observe a peak in photoluminescence quantum yield (PL QY) and Raman scattering intensity where SWNT length is maximized and bundling is minimized. Individualized SWNTs are found to exhibit high PL QY and high resonance-enhanced Raman scattering intensity. Fractions containing long, individual SWNTs exhibit the highest PL QY and Raman scattering intensities, compared to fractions containing single, short SWNTs or SWNT bundles. Intensity gains of approximately ~1.7 and 4-fold, respectively, are obtained compared with the starting material. Spectroscopic analysis reveals that SWNT fractions at higher displacement contain increasing proportions of SWNT bundles, which causes reduced optical transition energies and broadening of absorption features in the UV-Vis-NIR spectra, and reduced PL QY and Raman scattering intensity. Finally, we adsorb small aromatic species on "bright," individualized SWNT sidewalls and compare the resulting absorption, PL and Raman scattering effects to that of SWNT bundles. We observe similar effects in both cases, suggesting aromatic stacking affects the optical properties of SWNTs in an analogous way to SWNT bundles, likely due to electronic structure perturbations, charge transfer, and dielectric screening effects, resulting in reduction of the excitonic optical transition energies and exciton lifetimes.     

Electrochemical templating of metal nanoparticles and nanowires on single-walled carbon nanotube networks

The use of single-walled carbon nanotube (SWNT) networks as templates for the electrodeposition of metal (Ag and Pt) nanostructures is described. Pristine SWNTs, grown on insulating SiO2 surfaces using catalyzed chemical vapor deposition, served as the working electrode. In the simplest case, electrical contact was made by depositing a gold strip on the SWNT substrate (device 1). Deposition of Ag and Pt over extensive periods (30 s) resulted in a high density of particles on the SWNTs, with almost contiguous nanowire formation from the Au/SWNT boundary moving to isolated nanoparticles at further distances from the contact. For direct electrochemical studies of Ag and Pt nucleation, the assembly was coated in a resist layer and a small window opened up to expose only the electrically connected SWNTs to solution (device 2). In this case, the electrochemical signature in voltammetric and amperometric studies of metal deposition was due solely to processes at the SWNTs. Coupled with high-resolution microscopy measurements (atomic force microscopy and field emission scanning electron microscopy), this approach provided detail on the nucleation and growth mechanisms of Ag and Pt on SWNTs under electrochemical control. In particular, Ag growth was found to be rapid and progressive with an increasing nanoparticle density with time, whereas Pt deposition was characterized by lower nucleation densities and slower growth rates with a tendency for larger particles to be produced over long times.     

Chemical vapor depositions of single-walled carbon nanotubes catalyzed by uniform fe(2)o(3) nanoclusters synthesized using diblock copolymer micelles

Inversed micelles formed by polystyrene-block-poly(2-vinyl-pyridine) in toluene loaded with FeCl3 were used to synthesize and deliver discrete Fe2O3 nanoclusters with uniform diameters to flat substrates. Single-walled carbon nanotubes (SWNTs) were grown by chemical vapor deposition using these nanoclusters as the catalysts. Atomic force microscope characterizations revealed that high density SWNT mats were grown on the surface and the diameter of nanotubes was controlled by the diameter of nanoclusters. Electrical measurement revealed that the dense SWNT mats contained both semiconducting and metallic SWNTs and could be used to build thin film transistors.     

Electorchemical Studies of Cytochrome c on Electodes Modified by Single—Wall Carbon Naotubes

Single-wall carbon nanotubes(SWNTs) modified gold electrodes were prepared by using two different methods.The electrochemical behavior of cytochrome c on the modified gold electrodes was investigated.The first kind of SWNT-modified electrode (noted as SWNT/Au electrode)was prepared by the adsorption of carboxylterminated SWNTs from DMF dispersion on the gold electrode.The oxidatively processed SWNT tips were covalently modified by coupling with amines (AET) to form amide linkage.Via Au-S chemical bonding,the self-assembled monolayer of thiol-unctionalized nanotubes on gold surface was fabricated so as to prepare the others SWNT-modified electrode (noted as SWNT/AET/Au electrode).It was shown from cyclic voltammetry cxperiments that cytochrome c exhibited direct electrochemical responses on the both electrodes, but only the current of controlled diffusion existed on the SWNT/Au electrode while both the currents of controlled diffusion and adsorption of cytochrome c occurred on the SWNT/AET/Au electrode.Photoelastic Modulation Infared Reflection Absorpthion Spectroscopy (PEM-IRRAS) and Quartz Crystal Microbalance (QCM) were employed to verify the adsorption of SWNTs on the gold electrodes.The results proved that SWNTs could enhance the direct electron transfer proecss between the electrodes and redox proteins.     

Improving the effectiveness of interfacial trapping in removing single-walled carbon nanotube bundles

Single-walled carbon nanotube (SWNT) bundles are selectively removed from an aqueous dispersion containing individually suspended carbon nanotubes coated with gum Arabic via interfacial trapping. The suspensions are characterized with absorbance, fluorescence, and Raman spectroscopy as well as atomic force microscopy (AFM) and rheology. The resulting aqueous suspensions have better dispersion quality after interfacial trapping and can be further improved by altering the processing conditions. A two-step extraction process offers a simple and fast approach to preparing high-quality dispersions of individual SWNTs comparable to ultracentrifugation. Partitioning of SWNTs to the liquid-liquid interface is described by free energy changes. SWNT bundles prefer to reside at the interface over individually suspended SWNTs because of greater free energy changes.     

Regioselective competitive adsorption of water and organic vapor mixtures on pristine single-walled carbon nanotube bundles

Sequential adsorption of water and organic vapor mixtures onto single-walled carbon nanotube (SWNT) bundles is studied experimentally and by grand canonical Monte Carlo (GCMC) simulation to elucidate the distinct interactions between select adsorbates and the nanoporous structure of SWNTs. Experimental adsorption isotherms on SWNT bundles for hexane, methyl ethyl ketone, cyclohexane, and toluene individually mixed in carrier gases that were nearly saturated with water vapor are compared with the GCMC-simulated isotherms for hexane, as a representative organic, on the external surface of the heterogeneous SWNT bundles. From the nearly perfect overlap between the experimental and simulated isotherms, it is concluded that until near saturation only the internal pore volume of pristine SWNT bundles fills with water. The adsorption of water vapor on the peripheral surface of the bundles remains insignificant, if not negligible, in comparison to the adsorption of water in the internal volume of the bundles. This is in contrast with the adsorption of pure hexane, which exhibits appreciable adsorption both inside the bundles and on their external surface. It is also suggested that during competitive adsorption, water molecules take precedence over small nonpolar and polar organic molecules for adsorption inside SWNTs and leave unoccupied the hydrophobic external surface of the bundles for other more compatible adsorbates.     

Recent progress in chemical detection with single-walled carbon nanotube networks

Single-walled carbon nanotubes (SWNTs) have had significant impact on the development of gas sensors in the last decade. However, useful applications of SWNTs are limited by the lack of manufacturable routes to device formation. This Highlight article chronicles recent progress in this area and demonstrates the great promise of a new room temperature deposition method for SWNT networks in gas sensing applications. This liquid deposition technique allows the deposition of pre-treated, highly aligned SWNT networks on a wide variety of substrates. A significant advantage of SWNT-network sensors is that fluctuations in the electrical response of individual SWNTs become less important as the size of the network increases. Therefore, device properties can be controlled by the overall density of the network rather than the physical properties of any individual SWNT. At densities where semiconducting pathways dominate, highly sensitive thin-film chemoresistive sensors can be fabricated. Such devices also have higher signal-to-noise ratios and are easier to fabricate than devices based on a single SWNT.     

High dispersion and electrocatalytic properties of palladium nanoparticles on single-walled carbon nanotubes

Palladium (Pd) nanoparticles were electrochemically dispersed on single-walled carbon nanotubes (SWNTs) by electroreduction of octahedral Pd(IV) complex formed on the SWNT surface. The structure and nature of the resulting Pd-SWNT composites were characterized by transmission electron microscopy and X-ray diffraction. The electrocatalytic properties of the Pd/SWNT electrode for hydrazine oxidation have been investigated by cyclic voltammetry; high electrocatalytic activity of the Pd/SWNT electrode can be observed. This may be attributed to the high dispersion of palladium catalysts and the particular properties of SWNT supports. The results imply that the Pd-SWNT composite has good potential applications in fuel cells.     

Observation of negative and positive trions in the electrochemically carrier-doped single-walled carbon nanotubes

Understanding of electronic and optical features of single-walled carbon nanotubes (SWNTs) has been a central issue in science and nanotechnology of carbon nanotubes. We describe the detection of both the positive trion (positively charged exciton) and negative trion (negatively charged exciton) as a three-particle bound state in the SWNTs at room temperature by an in situ photoluminescence spectroelectrochemistry method for an isolated SWNT film cast on an ITO electrode. The electrochemical hole and electron dopings enable us to detect such trions on the SWNTs. The large energy difference between the singlet bright exciton and the negative and positive trions showing a tube diameter dependence is determined by both the exchange splitting energy and the trion binding energy. In contrast to conventional compound semiconductors, on the SWNTs, the negative trion has almost the same binding energy to the positive trion, which is attributed to nearly identical effective masses of the holes and electrons.     

Solubilization of single-wall carbon nanotubes by supramolecular encapsulation of helical amylose

We have developed a simple, efficient process for solubilization of single-wall carbon nanotubes (SWNTs) with amylose in aqueous DMSO. This process requires two important conditions, presonication of SWNTs and subsequent amylose treatment in an optimum mixture of DMSO/H2O. The former step separates SWNT bundles, and the latter step provides a maximum cooperative interaction of SWNTs with amylose, leading to the immediate and complete solubilization. The best solvent condition for this is around 10-20% DMSO, in which amylose assumes a random conformation or an interrupted helix. This indicates that the amylose helix is not the prerequisite for encapsulation of SWNTs. The SEM and AFM images of the encapsulated SWNTs manifest loosely twisted ribbons wrapping around SWNTs, which are locally intertwined as a multiple twist, but no clumps of the host amylose are seen on SWNT capsules.     

Catalytic polymerization and facile grafting of poly(furfuryl alcohol) to single-wall carbon nanotube: preparation of nanocomposite carbon

A nanocomposite carbon was prepared by grafting a carbonizable polymer, poly(furfuryl alcohol) (PFA), to a single-wall carbon nanotube (SWNT). The SWNT was first functionalized with arylsulfonic acid groups on the sidewall via a method using a diazonium reagent. Both Raman and FTIR spectroscopies were used to identify the functional groups on the nanotube surface. HRTEM imaging shows that the SWNT bundles are exfoliated after functionalization. Once this state of the SWNTs was accomplished, the PFA-functionalized SWNT (PFA-SWNT) was prepared by in situ polymerization of furfuryl alcohol (FA). The sulfonic acid groups on the surface of the SWNT acted as a catalyst for FA polymerization, and the resulting PFA then grafted to the SWNTs. The surfaces of the SWNTs converted from hydrophilic to hydrophobic when they were wrapped with PFA. The formation of the polymer and the attraction between it and the sulfonic acid groups were confirmed by IR spectra. A nanocomposite carbon was generated by heating the PFA-SWNT in argon at 600 degrees C, a process during which the PFA was transformed to nanoporous carbon (NPC) and the sulfonic acid groups were cleaved from the SWNT. Based upon the Raman spectra and HRTEM images of the composite, it is concluded that SWNTs survive this process and a continuous phase is formed between the NPC and the SWNT.     

Electrochemical functionalization of single-walled carbon nanotubes in large quantities at a room-temperature ionic liquid supported three-dimensional network electrode

Electrochemical functionalization of single-walled carbon nanotubes (SWNTs) was one of selective, clean, and nondestructive chemical methods. But in previous studies it met difficulties in homogeneous electrografting of SWNTs in large quantities because the reaction was often localized on a very thin film (ca. 2 microm). In this report, a room-temperature ionic liquid (RTIL) supported three-dimensional network SWNT electrode was first utilized to break through this barrier. In this work, large quantities of SWNTs were considerably untangled in RTILs so as to greatly increase the effective area of the electrode. N-succinimidyl acrylate (NSA), as a model monomer, was dissolved in the supporting RTILs and was electrografted onto SWNTs (SWNTs-poly-NSA). As an application example, glucose oxidase was directly covalently anchored on the SWNTs-poly-NSA assembly, and the electrocatalytic oxidation of glucose in this assembly was investigated. RTILs opened a new path in electrochemical functionalization of SWNTs.     

铂粒子修饰单壁碳纳米管/聚苯胺复合膜对甲醛的电催化氧化

在溶有单壁碳纳米管(SWNTs)的苯胺溶液中, 通过电化学共聚合法成功制备了单壁碳纳米管(SWNT)/聚苯胺(PANI)复合膜. 用电沉积法将铂沉积到SWNT/PANI复合膜上. 样品的成分和形貌分别用XRD和SEM表征. 四探针和电化学交流阻抗的研究表明被PANI包裹的SWNTs整齐地排列在复合膜中, 从而提高了复合膜的电导率, 促进了电荷转移. 循环伏安(CV)说明Pt修饰的SWNT/PANI复合膜对于甲醛氧化具有良好的电催化活性及稳定性. 研究结果表明SWNT/PANI复合膜是一种非常好的催化剂载体, 有着广泛的应用前景.     

Growth of millimeter-long and horizontally aligned single-walled carbon nanotubes on flat substrates

Millimeter-long and well-aligned single-walled carbon nanotubes (SWNTs) have been produced on silica/silicon surfaces using the carbon monoxide chemical vapor deposition (CO-CVD) method. The orientation of the nanotube arrays can be well-controlled by the gas flow during the growth. The majority of the orientated SWNTs are straight and individual. The length of the nanotubes can be >2 mm for a 10 min growth. Furthermore, multidimensional crossed-networks of SWNT can be easily generated by multistep processes. These results present a great opportunity in the controllable production of organized SWNT arrays for large-scale carbon nanotube-based nanodevice fabrication.     

Cover Picture

The cover picture shows a single-walled carbon nanotube (SWNT) functionalized with nucleophilic carbenes at the sidewall. Normally, single-walled nanotubes exist in the form of insoluble bundles. The sidewall addition of reactive organic groups such as radicals, nitrenes, or carbenes such as the ones shown in the cover picture disrupts the bundles. The background of the picture shows a typical AFM image of such derivatized SWNTs. The isolated SWNTs are soluble in organic solvents giving black solutions. This enables a spectroscopic characterization of nanotubes in solution. With this versatile sidewall functionalization the decisive requirements for the development of technological applications such as the production of ultrathin films or the processing to polymer composites with new electronic and mechanic properties have been compiled. Details about this new chemical funtionalization of SWNTs is described by Hirsch et al. on pp. 4002 ff.