乙烯基Ia3d介孔硅分子筛的环氧化及其固定化青霉素酰化酶(英文)

采用直接共聚法合成表面含有乙烯基的具有立方相Ia3d结构的介孔硅分子筛(V-ClMS),然后对乙烯基团进行环氧化制备得到表面环氧基功能化的介孔硅分子筛(E-CIMS),采用X射线衍射、N2吸附-脱附、透射电镜、热重分析和13C固体核磁共振对制备的介孔硅分子筛进行了表征.结果表明,表面含有乙烯基的V-ClMS介孔硅分子筛能被一步成功合成,并易于发生环氧化而获得表面环氧基功能化的E-CIMS介孔硅分子筛.将E-CIMS介孔硅分子筛作为载体用于固定化青霉素G酰化酶(PGA),研究了表面环氧基团对固定化PGA初活性和操作稳定性的影响.结果表明,随着表面环氧基团数量的增加,介孔硅分子筛孔径减小,表面疏水性增加,导致载酶量和初活性减小.但介孔硅分子筛表面适量的环氧基团能增强E-CIMS介孔硅分子筛与PGA之间的相互作用,从而提高固定化PGA的操作稳定性.     

一步液滴法合成酸性和孔道属性可调的硅铝酸盐载体及其Pd基催化剂的性能研究

通过一步液滴法在不同的反应溶剂体系下制备了一系列无定形硅铝酸盐载体, 并进一步制备出Pd基负载型多孔催化材料, 探究了反应溶剂极性和反应物Si/Al比对载体材料和催化剂的影响, 实现了通过一步液滴法调控硅铝酸盐酸性和孔道属性. 结果表明, 在极性较小的反应溶剂体系中制得了富含介孔的无定形硅铝酸盐载体材料, 并且通过改变Si/Al比可实现载体材料的酸性、 比表面积及孔道尺寸的调控, 比表面积和总酸量分别达到349.6 m²/g和1.389 mmol/g. 由于该载体材料高的比表面积及丰富的介孔孔道, 所制得的Pd基负载型多孔催化材料的Pd金属分散性达到了63.17%, 在硝基苯加氢反应中实现了99.75%的转化率和94.62%的选择性, 在苯甲醇氧化反应中表现出40.61%的转化率及38.09%的选择性, 远远优于利用商用载体合成的 Pd/Al₂O₃催化材料. 这种简单有效的合成方法使得按照目标催化反应的类型来设计高效催化剂成为可能.     

多级孔NaX分子筛的合成及CO2吸附性能

采用两步晶化和氨基酸辅助的协同合成策略, 制备了具有高产率(89%)和高结晶度(微孔体积为0.30 cm ³/g)的多级孔NaX分子筛. 利用X射线粉末衍射、 扫描电子显微镜、 透射电子显微镜和氮气吸附等技术, 考察了两步晶化和氨基酸加入量对NaX分子筛的形貌、 相对结晶度和产率的影响. 实验结果表明, 两步晶化有利于多级孔结构的产生, 氨基酸的引入有助于提高分子筛相对结晶度和产率. 与传统方法合成的NaX分子筛相比, 该合成策略制备的多级孔NaX分子筛展现出更优异的CO₂吸附性能, 在273 K和100 kPa条件下, 其CO₂吸附量达到154.2 cm ³/g, 而传统NaX分子筛的CO₂吸附量为147.6 cm ³/g. 该合成策略为绿色且高效制备高质量的多级孔分子筛提供了新思路.     

碱处理脱硅与提高Y型分子筛硅铝比——矛盾的对立与统一

考察了 "水热处理"以及"碱处理+水热处理"两种方法所制得的超稳 Y 分子筛的骨架硅铝比、孔结构特征以及酸量, 并探讨了"碱处理+水热处理"方法对起始 NaY 分子筛的适应性. 结果表明, 在水热处理前, 对 NaY 分子筛进行碱处理脱硅可在不改变最终样品的骨架超稳化水平和酸量的同时, 样品的介孔体积显著增加. 直接水热处理 NaY 分子筛所得样品介孔体积不超过 0.14 cm3/g, 而先碱处理后水热处理, 所得样品介孔体积可达 0.22 cm3/g. 该法适用于制备骨架硅铝比高的 NaY 分子筛. 起始原料的骨架硅铝比较低时, 所得样品的介孔体积增幅小, 而且微孔受损严重.     

介孔硅铝分子筛的合成、表征及其作为固体酸催化苯酚与1-辛烯的烷基化反应

以异丙醇铝、硅酸四乙酯和十六烷基三甲基溴化胺为原料,以乙酰丙酮为螯合剂,采用溶胶-凝胶法合成了硅铝比分别为25,50,100和150的介孔硅铝分子筛,并用其催化苯酚与1-辛烯的液相烷基化反应.X射线衍射、N2吸附、高分辨透射电镜及27Al核磁共振光谱表征结果表明,该介孔分子筛具有蠕虫状骨架结构.在160℃时,硅铝比为25的介孔硅铝分子筛催化剂上苯酚可以完全转化为单烷基苯酚.     

介孔分子筛MCM-41的硅烷化改性及吸附性能研究

高硅分子筛MCM-41具有均匀的中孔孔径分布、较大的比表面积(>900m2/g)[1-2],应用前景广阔.已在硅基分子筛的基础上合成了各种含有杂原子分子筛、金属氧化物分子筛、有机官能团分子筛[3-8].改变介孔MCM-41分子筛的表面组成可以较好地调节其吸附性能[9].本文以直接反应的方法用三甲基氯硅烷来修饰MCM-41.通过XRD、红外吸收光谱和比表面和孔隙率测定对样品进行了表征,并分别对改性前后样品进行了水与苯的吸附性能研究.     

介孔分子筛制备技术新进展—二次合成、超分子自组装和介孔生成剂法

具有内部介孔结构的多级孔分子筛兼具微孔分子筛和介孔材料的功能, 拥有良好的传质和催化特性. 在过去的几十年内, 介孔分子筛在催化、 吸附和分离领域发展迅速. 近年来, 新型合成方法的开发在很大程度上实现了介孔分子筛孔道结构、 组分及形貌灵活可控的调节. 本综述讨论了近期出现的多种新合成路径, 重点介绍了近期发展起来的二次合成制备低硅/铝介孔分子筛、 超分子自组装合成介孔分子筛及有机小分子原位合成介孔分子筛技术. 对这些合成技术的机理进行了讨论, 以期为介孔分子筛未来的发展提供思路. 文章的最后还讨论了不同的合成策略所面临的一些关键性挑战.     

介孔分子筛制备技术新进展——二次合成、超分子自组装和介孔生成剂法（英文）

具有内部介孔结构的多级孔分子筛兼具微孔分子筛和介孔材料的功能,拥有良好的传质和催化特性.在过去的几十年内,介孔分子筛在催化、吸附和分离领域发展迅速.近年来,新型合成方法的开发在很大程度上实现了介孔分子筛孔道结构、组分及形貌灵活可控的调节.本综述讨论了近期出现的多种新合成路径,重点介绍了近期发展起来的二次合成制备低硅/铝介孔分子筛、超分子自组装合成介孔分子筛及有机小分子原位合成介孔分子筛技术.对这些合成技术的机理进行了讨论,以期为介孔分子筛未来的发展提供思路.文章的最后还讨论了不同的合成策略所面临的一些关键性挑战.     

乙炔、丙烯在多种分子筛上的吸附和脱附性质

在80℃下研究了ZSM5、13X、Y、MOR、5A、SAPO34等多种分子筛和常见载体上乙炔和丙烯的吸附和脱附性能。结果表明，乙炔和丙烯在SiO2、γ-Al2O3上不吸附，而与分子筛存在较强的相互作用。对于同类型的分子筛，两者的饱和吸附量均随分子筛硅铝比的增大而减小。在同一种分子筛上，以摩尔计的丙烯吸附量均明显高于乙炔。在80℃改性β分子筛上乙炔和丙烯饱和吸附量可分别达到0.11mmol/g和4.89mmol/g，该结果明显高于文献报道的结果。     

介孔分子筛在生物酶固定化中的应用

综述了MCM-48和SBA-15等新型介孔分子筛用生物酶固定化载体研究的新进展。介孔分子筛由于拥有巨大的比表面积(~1000m2/g)、纳米尺寸孔道(2~50m)和较大的孔容(~1.0 cm3/g),因此以分子筛为载体利用物理吸附制备的固定化酶呈现出高的催化活性,但固定化酶操作稳定性较低,在使用过程中部分酶分子发生了脱落,其原因是分子筛表面自由的硅羟基通过物理吸附或氢键作用固定酶分子。借助介孔分子筛自身的自由硅羟基在表面嫁接-COOH、-NH2、-CH=CH2等有机官能团来构筑酶固定化的微环境,改善酶分子和载体的亲和作用,提高固定化酶的活性。目前,利用有机官能团功能化介孔分子筛固定化酶是研究发展的趋势。     

Amino acid adsorption on mesoporous materials: influence of types of amino acids, modification of mesoporous materials, and solution conditions

In order to disclose the dominant interfacial interaction between amino acids and ordered mesoporous materials, the adsorption behaviors of five amino acids on four mesoporous materials were investigated in aqueous solutions with adjustable amino acid concentration, ion strength, and pH. The selected amino acids were acidic amino acid glutamic acid (Glu), basic amino acid arginine (Arg), and neutral amino acids phenylalanine (Phe), leucine (Leu), and alanine (Ala), and the selected mesoporous materials were SBA-15, Al-SBA-15, CH3(10%)-SBA-15, and CH3(20%)-SBA-15. The adsorption capacities of Glu and Arg were strongly dependent on pH and surface charge of the mesoporous adsorbent. The adsorption of Phe showed pH insensitivity but depended on the surface organic functionalization of mesoporous adsorbent. On the basis of the theoretical analysis about the interaction between amino acid and adsorbent, such a remarkable difference was attributed to the different nature of the interaction between amino acid and adsorbent. Arg could be readily adsorbed on the surface of SBA-15, especially Al-SBA-15, under appropriate pH in which the electrostatic interaction was predominant. The driving force of Phe adsorption on mesoporous adsorbent mainly came from the hydrophobic interaction. Therefore, the adsorption capability of Arg decreased with increasing ion strength of solution, while the adsorption capability of Phe increased with the increasing degree of CH3 functionalization on SBA-15. For neutral amino acid Phe, Ala, and Leu, the adsorption capability increased with the increase of the length of their side chains, which was another evidence of hydrophobic effect. Thus, all the adsorption of amino acids on mesoporous silica materials can be decided by the combined influence of two fundamental interactions: electrostatic attraction and hydrophobic effect.     

A study of carboxylic-modified mesoporous silica in controlled delivery for drug famotidine

A series of pure silica MSU and carboxylic-modified MSU materials were prepared. The formation of mesoporous silica materials with terminal carboxylic groups on pore surface was performed by the acid-catalyzed hydrolysis of cyano to carboxylic. Then their potential applications in controlled drug delivery carriers were investigated. Drug famotidine was selected as a model molecule out of the consideration of the terminal amino groups in its molecule. The adsorption experiments show significant adsorption of famotidine on the carboxylic-modified MSU materials. And, the functionalization level of carboxylic groups has been found to be the key factor affecting the adsorption capacities of the modified MSU materials for famotidine. Subsequently, three kinds of release fluids, including simulated gastric medium, simulated intestinal medium, and simulated body fluid, were used to test the famotidine release rate from the carboxylic-modified MSU material. Obvious delayed effect has been observed for the famotidine release from the carboxylic-modified mesoporous silica material under the in vitro assays.     

Adsorption and photocatalytic decomposition of amino acids in TiO2 photocatalytic systems

The adsorption and photodecomposition of seven kinds of amino acids on a TiO2 surface were investigated by zeta potential measurements and 1H NMR spectroscopy in TiO2 aqueous suspension systems. The decomposition rates increased in the order of Phe < Ala < Asp < Trp < Asn < His < Ser. For Phe, Trp, Asn, His, and Ser, the isoelectric point (IEP) of TiO2 shifted to a lower pH with increasing decomposition rates upon adsorption on TiO2, suggesting that the effective adsorption and photocatalytic sites for these amino acids should be the basic terminal OH on the solid surface. Since the amino acids that decomposed faster than the others contain -OH (Ser), -NH (Trp, His), or -NH2 (Asn) in their side chain, they are considered to interact with the basic terminal OH groups more preferably by the side chain and are vulnerable to photocatalytic oxidation. On the other hand, Ala interacts with the acidic bridged OH on TiO2 to cause an IEP shift to a higher pH. The correlation of the surface hydroxyl groups with the photocatalysis of amino acids was verified by the use of calcined TiO2 without surface hydroxyl groups.     

介孔炭表面性质对吸附去除低浓度氨性能的影响

室内环境中低浓度氨污染普遍存在,影响人的身体健康,而消除这些低浓度的氨相对困难。本文报道了一种适用于低浓度氨吸附去除的介孔炭材料,其性能明显优于经硝酸处理的活性炭材料。该介孔炭采用磷酸铝为硬模板制备,炭表面存在大量含氧官能团,研究显示炭表面羧基和内酯基在吸附氨过程中发挥着重要作用,它们作为酸性中心与氨发生化学作用,可以有效地捕获空气中低浓度的氨污染物。     

SAB-16型介孔材料的制备、表征及表面改性——介绍一个材料化学综合实验

A new comprehensive experiment of material chemistry: the synthesis and characterization of SBA-16 mesoporous materials, and surface modification was introduced. This experiment combines the theory of thermodynamics, kinetics and surface adsorption, as well as instrumental analysis, which could improve the experimental skills, comprehensive and innovative abilities of the undergraduates. Based on this experiment, students can not only well understand the forming principle of mesoporous materials, but also learn the operation skill for XRD, N₂ adsorption, TEM, Intelligent Gravimetric Analyzer, which could stimulate the interest in scientific research.     

Improved selection of LMW over HMW proteins from human plasma by mesoporous silica particles with external modification

Selective extraction of low molecular weight (LMW) proteins and peptides from complex biological samples plays an important role in the discovery of useful biomarkers and signaling molecules. Various methods, such as solid-phase extraction (SPE), ultrafiltration, and size-exclusion chromatography have been developed for such extraction purpose. In this study, we present, to our knowledge, the first demonstration of alkyl-diol@SiO₂ mesoporous material MCM-41 (alkyl-diol group on the external surface of mesoporous material) for selective extraction of LMW proteins and peptides from complex biological samples. The adsorption kinetics of LMW proteins, the influence of pH on adsorption and the desorption recovery by different elution solvents were investigated by using standard proteins as model samples. It was demonstrated that the modification of alkyl-diol group on the external surface could efficiently decrease the adsorption of HMW protein and increase the desorption recovery of LMW protein. Furthermore, the mesoporous materials were applied to selectively extract LMW proteins and peptides (<10 kDa) from crude human plasma. And the modified MCM-41 material had much better extraction selectivity and efficiency for LMW proteins and peptides than unmodified one.     

Characterization of the hydrophobicity of mesoporous silicas and clays with silica pillars by water adsorption and DRIFT

The hydrophobic-hydrophilic properties of a solid are related to the material chemistry and, often, these properties are relevant to the applications of a particular material. Contrarily to what happens with other properties, such as specific surface areas or pore volumes, the methodologies to ascertain on the hydrophilicity of a porous material are not well defined. In this work, we discuss and relate the information on the hydrophobicity degree obtained from water adsorption isotherms and from diffuse reflectance infrared Fourier transform (DRIFT), in a set of porous materials. The studied materials were mainly mesoporous solids, namely of MCM-41 and SBA-15 types, two xerogels and also different porous clays heterostructures. Both techniques were informative on the hydrophobic-hydrophilic properties of the studied samples, but the correlation between the information obtained by each technique was not straightforward. Water adsorption isotherms are much more sensitive to the differences of the studied materials than the DRIFT spectra. For silica-based mesoporous materials with similar surface chemistry, the water adsorption process and hence, the hydrophobic-hydrophilic properties, is mainly dependent on the pore diameters. However, water adsorption is much more sensitive to changes in the nature of the adsorbent surface than to changes in the pore diameter.     

Modified Mesoporous Silicate MCM-41 for Zinc Ion Adsorption: Synthesis, Characterization and Its Adsorption Behavior

Modified MCM‐41 has been prepared by bi‐functionalization of thiol and amino functional groups onto mesoporous silicate MCM‐41. Elemental analysis (EA), thermogravimetry analysis (TGA) and FTIR techniques were used to quantify the attachment of the thiol and amino functional groups to the mesoporous silicate pore wall. Powder X‐ray diffraction (PXRD) and nitrogen adsorption techniques were used to establish the pore diameter, packing of the pores and specific surface area of the modified mesoporous silicate MCM‐41. Adsorption behavior for 18 metal ions on this sorbent has been studied and discussed. This sorbent has high affinity for zinc ions against amino‐ or thiol‐functionalized MCM‐41 sorbents.     

Mesoporous Silica Nanoparticles Functionalized with Amino Groups for Biomedical Applications

The synthesis and characterization of amino-functionalized mesoporous silica nanoparticles are presented following two different synthetic methods: co-condensation and post-synthesis grafting of 3-aminopropyltriethoxysilane. The amino groups’ distribution on the mesoporous silica nanoparticles was evaluated considering the aggregation state of a grafted photosensitizer (Verteporfin) by using spectroscopic techniques. The homogeneous distribution of amino groups within the silica network is a key factor to avoid aggregation during further organic functionalization and to optimize the performance of functionalized silica nanoparticles in biomedical applications. In addition, the formation of a protein corona on the external surface of both bare and amino-functionalized mesoporous silica was also investigated by adsorbing Bovine Serum Albumin (BSA) as a model protein. The adsorption of BSA was found to be favorable, reducing the aggregation phenomena for both bare and amino-modified nanoparticles. Nevertheless, the dispersant effect of BSA was much more evident in the case of amino-modified nanoparticles, which reached monodispersion after adsorption of the protein, thus suggesting that amino-modified nanoparticles can benefit from protein corona formation for preventing severe aggregation in biological media.     

介孔C/SiO2粉体的制备及对阳离子型染料的吸附

采用吸附法处理染料废水需要合适的吸附剂。利用溶剂蒸发自组装法,以甲阶酚醛树脂为碳源、介孔SiO2粉体为载体制备介孔C/SiO2粉体,表征所制C/SiO2粉体的结构,研究C/SiO2粉体对阳离子型染料亚甲基蓝和阳离子红X-GRL的吸附性能,并与相同条件下制备的非负载的多孔C粉体以及介孔SiO2载体进行比较。结果表明,介孔C/SiO2粉体的孔窗口为11~18 nm,比表面积为303 m2.g-1,比孔容为1.11 cm3.g-1;C/SiO2粉体对这两种染料吸附量均高于C粉体和SiO2载体;在pH≤10的范围内,吸附量随pH值增大而显著提高。