CP/MAS ~(13)C NMR技术对木浆纤维微观结构的研究

利用交叉极化结合魔角旋转技术~(13)C核磁共振法(CP/MAS ~(13)C NMR)对桉木浆纤维的微观结构进行研究,为进一步研究木质纤维素材料开发过程中反应障碍特征奠定基础.通过对NMR光谱C1区(δ 102～108)进行洛仑兹拟合,得到桉木浆纤维中纤维素Iα的相对含量为26.92%,纤维素Iβ的相对含量为52.04%,主要以纤维素Iβ晶体形式为主.通过计算纤维素C4结晶区(δ 86～92)和非结晶区(δ 80～86)的相对含量得到桉木浆的纤维素结晶度为47%.通过洛仑兹和高斯函数的混合模型对NMR光谱C4区(δ 80～92)进行拟合得到基原纤尺寸和微原纤横向尺寸分别为4.0与17.9 nm,并通过计算不同形态的结晶纤维素的相对含量得到纤维素结晶度为51%,证实了在微原纤内部次晶纤维素的存在.     

高岭石结构缺陷的 1H MAS NMR和Raman研究

The structure default of kaolinites was characterized with ¹H MAS NMR and Raman spectra. Although the HI indexes of Suzhou and Maoming kaolinite are similar, their ¹H MAS NMR and Raman spectra are very different. ¹H MAS NMR showed that the hydroxyl proton chemical shifts of Suzhou kaolinite are in the higher field and with larger different between the inner surface hydroxyls protons and inner hydroxyls proton chemical shifts than Maoming kaolinite. Raman spectra showed that the surface hydroxyls stretching vibration bands of Suzhou kaolinite are in the high frequency region, and the half height widths of the bands are 7.0～14 cm^-1. The area ratio S_z/(S_z+S_A), where S_Z and S_A are the areas of bands 3685 cm^-1 and 3695 cm^-1 respectively, is 0.23. But the surface hydroxyls stretching vibration bands of Maoming kaolinite are in the low frequency region, and the half height widths of the bands are 8.9～15.1 cm^-1. The area ratio S_z/(S_z+S_A) is 0.77. Those data proved that Suzhou kaolinite has lower structure default than Maoming kaolinite and ¹H MAS NMR and Raman spectra are effective method for study of kaolinite structure default.     

31P MAS NMR固体核磁共振研究稀土改性Y分子筛的酸性

以三甲基磷氧（TMPO）和三丁基磷氧（TBPO）为探针分子,用³¹P魔角旋转核磁共振（³¹P MAS NMR）法对稀土改性Y型分子筛的酸性进行了定性和定量分析. 结果表明,以TMPO为探针分子的³¹P MAS NMR谱分别在δ = 78,70,65,62,58,55和53处存在与酸中心相关的吸收峰,其中δ = 78和70处吸收峰与分子筛内部和外部酸性有关,δ = 65,62,58和53处吸收峰归属于TMPO在分子筛内部Brönsted酸中心上的贡献,δ = 55处吸收峰归属于TMPO在分子筛内部Lewis酸中心上的贡献. 随着稀土含量的增加,中等强度Brönsted酸中心（δ = 62和58）数量显著增加,而强Brönsted酸中心（δ = 65）和较弱Lewis酸中心（δ = 55）数量显著降低. 结合分子筛骨架铝和非骨架铝对分子筛酸性的影响进一步探讨了稀土改型Y分子筛的酸性.     

Li＋在PC＋DMF混合溶剂中优先溶剂化的13C NMR研究

利用¹³C NMR光谱技术研究了Li^＋在碳酸丙烯酯(PC)＋N,N-二甲基甲酰胺(DMF)混合溶剂中的优先溶剂化现象. 根据溶剂分子中碳原子的化学位移随锂盐浓度的变化关系, 确定了与Li^＋发生配位的原子. 碳原子的配位位移值随混合溶剂组成的变化关系表明, 在LiClO₄＋PC＋DMF混合物中, DMF分子对Li^＋的溶剂化作用较PC分子强. 定量计算得到, 在n(PC)∶n(DMF)＝1∶1(摩尔比)的混合溶剂中, PC与DMF分子数在Li^＋第一溶剂化层中的比率为0.12, 说明Li^＋优先被DMF分子溶剂化.     

Li＋在PC＋DMF混合溶剂中优先溶剂化的13C NMR研究

利用¹³C NMR光谱技术研究了Li^＋在碳酸丙烯酯(PC)＋N,N-二甲基甲酰胺(DMF)混合溶剂中的优先溶剂化现象. 根据溶剂分子中碳原子的化学位移随锂盐浓度的变化关系, 确定了与Li^＋发生配位的原子. 碳原子的配位位移值随混合溶剂组成的变化关系表明, 在LiClO₄＋PC＋DMF混合物中, DMF分子对Li^＋的溶剂化作用较PC分子强. 定量计算得到, 在n(PC)∶n(DMF)＝1∶1(摩尔比)的混合溶剂中, PC与DMF分子数在Li^＋第一溶剂化层中的比率为0.12, 说明Li^＋优先被DMF分子溶剂化.     

MCM-41分子筛的合成及129Xe核磁共振的研究

Purely siliceous MCM-41 with a narrow pore-size distribution, different pore size, high surface area was synthesized . As prepared, calcined and catalytically tested MCM-41 materials have been comprehensively characterized by N₂ adsorption/desorption at 77K and ¹²⁹Xe NMR. By adding mesitylene during the synthesis, the pore size of MCM-41 was enlarged to 5.2nm. The chemical shift in ¹²⁹Xe NMR spectroscopy of adsorbed xenon indicates that the MCM-41 is one dimensional pore channels .     

13C-NMR分析混合酸处理脱灰对永兴褐煤结构的影响

运用煤的结构化学理论和固态 ¹³C-NMR的研究方法,对比分析了永兴褐煤在混合酸处理脱灰前后碳组成的变化。研究表明,混合酸处理脱灰对永兴褐煤中脂肪碳和芳香碳两者比例分配的影响并不大,但对季碳、环内氧接脂碳、芳香桥碳和羧基碳的破坏作用比较明显;在芳香桥碳锐减的同时,芳甲基的比例非但没有减少反而略有增加,表明永兴褐煤中的双环及多环结构被破坏为单环结构,芳香簇的尺寸变小了,这是混合酸处理脱灰对永兴褐煤结构最重要的影响。     

仲胺型硝化纤维素对肌酐吸附机理的研究

利用IR, ¹³C NMR和XPS等技术研究了仲胺型硝化纤维素(ACN)对肌酐(CRE)的吸附行为, 提出了可能的吸附路线. 光谱分析的结果表明在模拟人体生理条件下, ACN对CRE的吸附是通过碱化的硝酸酯基与CRE的胍基碳生成离子复合物达到的.     

光活性聚甲基丙烯酸三苯甲酯链结构的研究——PTrMA的~(13)C液体和固体NMR谱

<正> 80年代出现的光活性高聚物—聚甲基丙烯酸三苯甲酯(PTrMA)是由非手性单体经不对称阴离子聚合得到的。近年来,PTrMA作为手性固定相在分离手性化合物方面得到了越来越多的实际应用。由于聚合物侧基上的三个苯基产生的大位阻,使它具     

东胜长焰煤热解含氧官能团结构演化的13C-NMR和FT-IR分析

以东胜煤田色拉一号井田2号煤层长焰煤为研究对象,利用浮沉离心法富集其镜质组。基于工业分析、元素分析、¹³C-NMR、FT-IR、谱图分峰拟合技术和化学分析测试,求取镜煤及一系列热解煤含氧官能团结构与含量参数,从不同角度研究了含氧官能团的分布规律与演化特点。镜煤中羧基、羰基含量分别为8.91~10.90 mol/kg、1.61~1.79 mol/kg,随热解温度升高羧基显著减少。热解作用促使以端基形式连接在脂肪链或脂肪环结构氧上的甲基和亚甲基首先脱去,且在温度高于350 ℃后基本稳定。氧在热解过程赋存状态的变化是芳香体系与脂肪体系相互竞争的结果,510 ℃热解煤中芳香类氧和脂肪类氧的含量分别为7.49、3.45 mol/kg。羟基的演化过程与热解过程中氧的赋存状态密切相关。随着热解过程的进行,在热解温度低于440 ℃时,各种羟基含量均减少,热解过程对于大分子网络的破坏干扰了各种氢键作用,而羟基π作用则暂时增强,至510 ℃时各种氢键含量均降为最低。东胜长焰煤中含氧官能团化学活性顺序为:[COOH]>[R-O]>[Ar-O-Ar,Ar-O-C,C-O-C]>[C=O]。镜煤非活性醚键含量为0.68 mol/kg,活性醚键为0.48 mol/kg,主要为非活性醚键。     

Secondary structure of peptides 16th. Characterization of proteins by means of13C NMR CP/MAS spectroscopy

50.3 or 75.4 MHz¹³C NMR cross-polarization/magic angle spinning spectra of human hair, horse hair, horse hoof, parrot feather, sperm whale myoglobin, and horse heart cytochrome C were measured. The spectra of human hair and horse hair indicate nearly equal mole fractions of-sheets and-helices and a low percentage of amorphous regions, whereas horse hoof contains a higher fraction of amorphous proteins. The parrot feathers contain a small-helix fraction (ca. 10±5 %) in additon to a large-sheet fraction whereas cytochrome C contains 70–90%-helices. The spectrum of myoglobin could not interpreted in terms of defined secondary structures. The usefulness of the¹³C NMR CP/MAS spectroscopy for the characterization of proteins is compared with that of IR spectroscopy and X-ray diffraction.     

Blending to Make Nonhealable Polymers Healable: Nanophase Separation Observed by CP/MAS 13C NMR Analysis

Can commodity polymers are made to be healable just by blending with self-healable polymers? Here we report the first study on the fundamental aspect of this practically challenging issue. Poly(ether thiourea) (PTUEG₃; T_g=27 °C) reported in 2018 is extraordinary in that it is mechanically robust but can self-heal even at 12 °C. In contrast, poly(octamethylene thiourea) (PTUC₈; T_g=50 °C), an analogue of PTUEG₃, cannot heal below 92 °C. We found that their polymer blend self-healed in a temperature range above 32 °C even when its PTUEG₃ content was only 20 mol %. Unlike PTUEG₃ alone, this polymer blend, upon exposure to high humidity, barely plasticized, keeping its excellent mechanical properties due to the non-hygroscopic nature of the PTUC₈ component. CP/MAS ¹³C NMR analysis revealed that the polymer blend was nanophase-separated, which possibly accounts for why such a small amount of PTUEG₃ provided the polymer blend with humidity-tolerant self-healable properties.     

13C固体核磁共振分析煤中含氧官能团的研究

采用 ¹³C交叉极化/魔角旋转-核磁共振（¹³C CP/MAS NMR）技术对四种煤进行分析,结合化学分析方法,考察了含氧官能团的分布规律,尤其是非活性醚键的含量。结果表明,¹³C CP/MAS NMR方法可以定量分析煤中部分含氧官能团,四种煤中羧基和羰基的含量分别为0.00~1.41和0.45~1.91 mol/kg;¹³C CP/MAS NMR与化学分析方法结合,可以定量解析煤中非活性醚键的含量,四种煤的醚键含量值为5.33~10.54 mol/kg,而活性醚键含量仅为0.04~0.13 mol/kg,煤中醚键的赋存状态以非活性醚键为主。     

Structural studies of bacterial cellulose through the solid-phase nitration and acetylation by CP/MAS <Superscript>13</Superscript>C NMR spectroscopy

The solid-phase nitration and acetylation processes of bacterial cellulose have been investigated mainly by CP/MAS ¹³C NMR spectroscopy to clarify the features of these reactions in relation to the characterization of the disordered component included in the microfibrils. CP/MAS ¹³C NMR spectra of bacterial and Valonia cellulose samples are markedly changed as the nitration progresses, in a similar way to the case of cotton linters previously reported; and the relative reactivity of the OH groups in the glucose residues is found to decrease in the order of O(6)H>O(2)H>O(3)H. Moreover, the nitration rate and mode greatly depend on the concentration of nitric acid in the reaction media. At dilute and medium concentrations, the O(6)H groups in the crystalline and disordered components are subjected to nitration at nearly the same rate, indicating that these two components are distributed almost at random in the entire region of each microfibril. The preferential penetration of nitric acid into each microfibril also occurs prior to nitration at the medium concentration, resulting in an increase in the mole fraction of the disordered component. In contrast, all OH groups undergo nitration very rapidly at the higher concentration, although nitration levels off to a certain extent for O(3)H groups. In solid-phase acetylation, no regio-selective reactivity is observed among the three kinds of OH groups, which may be due to the characteristic reaction that proceeds in a very thin layer between the acetylated and nonacetylated regions in each microfibril. The almost random distribution of the disordered component in the entire region of the microfibrils is also confirmed in this solid-phase acetylation. On the basis of these results, the mechanism of the solid-phase reactions and the microfibril structure are discussed.     

Solid‐state CP/MAS 13C NMR studies on conformational polymorphism in sertraline hydrochloride,an antidepressant drug

The C(2) isotropic chemical shift values in solid‐state CP/MAS ¹³C NMR spectra of conformational polymorphs Form I (δ 28.5) and III (δ 22.9) of (1S,4S)‐sertraline HCl ( 1 ) were correlated with a γ‐gauche effect resulting from the respective 162.6° antiperiplanar and 68.8° (+)‐synclinal C(2)? C(1)? N? CH₃ torsion angles as measured by X‐ray crystallography. The similarity of the solution‐state C(2) chemical shifts in CD₂Cl₂ (δ 22.8) and DMSO‐d₆ (δ 23.4) with that for Form III (and other polymorphs having C(2)? C(1)? N? CH₃ (+)‐synclinal angles) strongly suggests that a conformational bias about the C(1)? N bond exists for 1 in both solvents. This conclusion is supported by density functional theory B3LYP/6‐31G(d)‐calculated relative energies of C(1)? N rotameric models: (kcal) 0.00 [73.8 °C(2)? C(1)? N? CH₃ torsion angle], 0.88 (168.7°), and 2.40 (?63.4°). A Boltzmann distribution of these conformations at 25 °C is estimated to be respectively (%) 80.3, 18.3, and 1.4. Copyright © 2002 John Wiley & Sons, Ltd.     

13C and 15N CP/MAS, 1H–15N SCT CP/MAS and FTIR spectroscopy as tools for qualitative detection of the presence of zwitterionic and non‐ionic forms of ansa‐macrolide 3‐formylrifamycin SV and its derivatives in solid state

¹³C, ¹⁵N CP/MAS, including ¹H–¹³C and ¹H–¹⁵N short contact time CP/MAS experiments, and FTIR methods were applied for detailed structural characterization of ansa‐macrolides as 3‐formylrifamycin SV (1) and its derivatives (2–6) in crystal and in powder forms. Although HPLC chromatograms for 2/CH₃OH and 2/CH₃CCl₃ were the same for rifampicin crystals dissolved in respective solvents, the UV–vis data recorded for them were different in 300–375 nm region. Detailed solid state ¹³C and ¹⁵N CP/MAS NMR and FTIR studies revealed that rifampicin (2), in contrast to 3‐formylrifamycin SV (1) and its amino derivatives (3–6), can occur in pure non‐ionic or zwitterionic forms in crystal and in pure these forms or a mixture of them in a powder. Multinuclear CP/MAS and FTIR studies demonstrated also that 3–6 derivatives were present exclusively in pure zwitterionic forms, both in powder and in crystal. On the basis of the solid state NMR and FTIR studies, two conformers of 3‐formylrifamycin SV were detected in powder form due to the different orientations of carbonyl group of amide moiety. The PM6 molecular modeling at the semi‐empirical level of theory, allowed visualization the most energetically favorable non‐ionic and zwitterionic forms of 1–6 antibiotics, strongly stabilized via intramolecular H‐bonds. FTIR studies indicated that the originally adopted forms of these type antibiotics in crystal or in powder are stable in standard laboratory conditions in time. The results presented point to the fact that because of a possible presence of two forms of rifampicin (compound 2), quantification of the content of this antibiotic in relevant pharmaceuticals needs caution. Copyright © 2013 John Wiley & Sons, Ltd.     

~(13)C-NMR STUDY OF ETHYLENE-1-OCTENE COPOLYMERS

A ~(13)C-NMR method is presented for a quantitative determination of the respective monomercomposition and sequence distributions in ethylene-1-octene copolymers prepared with supportedtitanium/magnesium catalyst. On the basis of the sequence distributions, the ethylene-1-octenecopolymerization mechanism was studied. It was found that the observed sequence distributions inethylene-1-octene copolymers are satisfactorily predicted by the two-site model M/M,in whichthe copolymerization proceeds according to first-order Markovian statistics at the two differentsites.     

13C CP/MAS NMR studies of morphological changes in polypropylene: 2. The double melting endotherm of spunbonded fabrics

The double melting endotherm of spunbonded isotactic polypropylene (iPP) fabrics was investigated by monitoring changes in the solid-state NMR spectrum that result from thermal annealing. The DSC melting thermogram was found to change from a double to a single endotherm at anneal temperatures ≥156°C, with a concomitant increase in percent crystallinity. All of the carbon resonances in the CP/MAS NMR spectrum of the purely crystalline phase of iPP were found to be composed of multiple peaks with relative intensities that depend on anneal temperature. By monitoring the changes in the distribution of intensity among the various peaks of a given resonance, a transition temperature of 156°C was identified. Arguments are presented that this redistribution of intensity within a given carbon resonance characterizes the transformation from the α₁ to the α₂ monoclinic crystal form. The exothermicity associated with this transformation is responsible for the observation of a double melting endotherm by DSC. The splitting patterns observed in the NMR spectrum are discussed in terms of interlayer distances between layers of isochiral helices and the density of exposed methyls at the contact faces of these interlayers. © 1996 John Wiley & Sons, Inc.     

CP/MAS 13C NMR analyses of hydrogen bonding and the chain conformation in the crystalline and noncrystalline regions for poly(vinyl alcohol) films

The chain conformation and hydrogen bonding in the crystalline and noncrystalline regions have been characterized for atactic poly(vinyl alcohol) (PVA) films prepared under different conditions by CP/MAS ¹³C NMR analyses developed recently. The CH resonance lines of the crystalline and noncrystalline components split in different ways, depending significantly on casting solvents and annealing. These lines are found to be successfully resolved into 3–7 constituent lines by the least‐squares curve fitting. In this analysis, nine lines with different chemical shifts are prepared as elementary lines for the curve fitting by assuming the upfield shifts due to the γ‐gauche effect and the downfield shifts due to the formation of the intramolecular hydrogen bonds. The integrated intensities of the constituent lines thus obtained are also interpreted in terms of statistical calculations, assuming the random distribution of the trans and gauche conformations along PVA chains and the statistical distribution of the intramolecular and intermolecular hydrogen bonds between appropriate adjacent OH groups. On the basis of probabilities f_t and f_a for the trans conformation and the intramolecular hydrogen bond obtained through these analyses, the effects of casting solvents and annealing are discussed for both crystalline and noncrystalline components. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1–9, 2000