亚硝基铁氰化钠分光光度法测定药品“必理通”中对乙酰氨基酚含量

用亚硝基铁氰化钠分光光度法测定药品“必理通”中的对乙酰氨基酚含量。采用亚硝基铁氰化钠试液为显色剂,蒸馏水做溶剂,在波长为700nm下有最大吸收,利用分光光度计测定不同浓度溶液的吸光度,并绘制标准曲线进行分析。实验证明,对乙酰氨基酚在0．024mg／mL～0．168mg／mL浓度范围内,吸光度与样品浓度的线性关系良好,回收率在98．0％以上。此测定方法准确、快速、简便,是测定对乙酰氨基酚含量的最佳方法之一。     

Reversed-phase ion-pair chromatographic method for the determination of nitroprusside in photolyzed solutions

A rapid reversed-phase ion-pair chromatographic method for disodium pentacyanonitrosylferrate(II) (nitroprusside) and its photodegradation products nitrite, nitrate, hexacyanoferrate(II) and hexacyanoferrate(III) is described. For chromatography, phenyl-bonded pellicular silica gel (10 μm) was used with a mobile phase consisting of water (0.005 M tetrabutylammonium phosphate, 0.0011 M n-octylamine, 0.01 M potassium dihydrogenphosphate, pH 7.0) and methanol (0.005 M tetrabutylammonium phosphate, 0.0011 M n-octylamine) (65:35); the detector was set at 220 nm. In 5% (w/v) dextrose solutions, the calibration graph for nitroprusside was linear over the concentration range 10–120 μg ml^?1. A qualitative explanation for the order of retention: hexacyanoferrate(II) < hexacyanoferrate(III) < nitroprusside is given. The method is suitable for the selective determination of nitroprusside in photolyzed infusion solutions (100 μg ml^?1 in aqueous 5% dextrose) and gives an impression of the decomposition products formed.     

Chemiluminescence detection of sodium nitroprusside using flow injection analysis

A simple continuous-flow chemiluminometric method for the determination of 0.05-10 microg/ml of sodium nitroprusside is described. The method is based on the catalyses of luminol oxidation by hydrogen peroxide in alkaline medium. The method is sensitive and requires no sample pre-treatment and solutions can be analysed at a rate of 40 samples/hr with a relative error of about 1.18%. The method was satisfactory for the determination of sodium nitroprusside in a pharmaceutical preparation. The effect of some potential interferents is described.     

Voltammetric Sensor for Sodium Nitroprusside Determination in Biological Fluids Using Films of Poly‐L‐Lysine

Sodium nitroprusside (NP), a commercial vasodilator, can be pre‐concentrated on vitreous carbon electrode modified by films of 97.5%: 2.5% poly‐L ‐lysine (PLL): glutaraldehyde (GA). This coating gives acceptable anion exchange properties whilst giving the required improvement of adhesion to the glassy carbon electrode surface. Linear response range and detection limit on nitroprusside in B‐R buffer pH 4.0, were 1×10^?6 to 2×10^?5 mol L^?1 and 1×10^?7 mol L^?1, respectively. The repeatability of the proposed sensor, evaluated in term of relative standard deviation, was measured as 4.1% for 10 experiments. The voltammetric sensor was directly applied to determination of nitroprusside in human plasma and urine samples and the average recovery for these samples was around 95–97% without any pre treatment.     

Rapid and Convenient Method for the Determination of Sodium Nitroprusside in Aqueous Solution

Abstract

We propose a rapid and convenient method for the determination of sodium nitroprusside in aqueous solution. In alkaline medium and in the presence of dimethylsulfoxide, the concentration of the nitrite ions coming from the nitroprusside corresponds with the initial quantity of this compound.     

在丙酮增敏作用下硝普钠分光光度法测定盐酸吗啉胍

摘要：建立了可见分光光度法测定盐酸吗啉胍的新方法。研究表明,当NaOH浓度为0.13mol/L,在丙酮存在下硝普钠与盐酸吗啉胍反应生成紫色N-亚硝基类化合物,其最大吸收波长为508nm,表观摩尔吸光系数2.5×10³ L/（mol•cm）。盐酸吗啉胍浓度在0.38×10^-6~3.0×10^-4 g/mL范围内与吸光度呈现良好线性关系,线性回归方程A = 0.02292 + 0.01213c (10^-6 g/mL),线性相关系数r=0.9998,检测限(3σ/k)为0.25×10^-6 g/mL,RSD = 0.21%。本方法可用于药物样品和血清中盐酸吗啉胍含量的测定。     

Photometric determination of mercaptans in light petroleum products

A procedure for the photometric determination of mercaptan sulfur in light petroleum products was developed. This procedure is based on the formation of colored analytical species in an aqueous extract to an alkaline solution of sodium nitroprusside. The determination level was 3 mg/L at a sample volume of 1 mL.     

Polarography of disodium pentacyanonitrosylferrate(II): Part 2. Determination at Therapeutic Levels in Serum,Plasma, and Whole Blood

Disodium pentacyanonitrosylferrat(II) (sodium nitroprusside) is determined at therapeutic (ng ml^?1) levels in plasma, serum and blood with conventional and high-performance differential pulse polarography (d.p.p. and h.p.d.p.p.) at a dropping mercury electrode or a static mercury drop electrode. Serum or plasma (3 ml) is treated with perchloric acid containing 1 mg ml^?1 potassium hexacyanoferrate(II), centrifuged for 10 min and subjected to polarography. For spiked serum, calibration graphs are linear over the range 30–1000 ng ml^?1 sodium nitroprusside, regardless of the polarographic technique; the estimated detection limit is 15 ng ml^?1 (5 × 10^?8 M). Calculated therapeutic levels range from 100 to 1000 ng ml^?1. Similar results were obtained for spiked plasma. A similar procedure is suitable for whole blood and was used to study the in-vitro degradation of sodium nitroprusside (200 ng ml^?1) on incubation at 37°C. The in-vitro loss is rapid (t_{$\text{1}\text{2}$} ≈ 6 min) but meaningful in-vivo levels can be obtained when the blood is collected in a 0.9% sodium chloride solution at 0°C. Thiocyanate, the main metabolite of nitroprusside, and thiosulphate, which is a potential antidote for cyanide, do not interfere.     

Cyclic flow-injection photometric determination of mercaptans in hydrocarbon gases

A procedure for the automated photometric determination of mercaptans in hydrocarbon gases was developed using sodium nitroprusside as a photometric reagent. The analytical range was from 10 to 150 mg/m³ at a sample volume of 0.4 L and preconcentration time of 2 min.     

Spectrophotometric Study and Potentiometric Titration between Sulphite and Nitrite Ions Using Acktaldehyde Complex of Nitroprusside as a Carrier

Abstract

A complex between sodium nitroprusside (NP) and acetaldehyde of 1:1 in aqueous solution of pH 10 has been prepared and used as an analytical reagent for the spectrophotometric determination of sulphite and nitrite ions. Nitrite ion can be titrated against sulphite ion and vise versa in equivalent amounts with high accuracy in the presence of the acetaldehyde complex of nitroprusside as a carrier using a potentiometric titration technique.     

Determination of low concentrations of acetaldehyde in ethylene oxide

The method is based on a qualitative test for acetaldehyde in which the reagents sodium nitroprusside and piperidine react with acetaldehyde to form a coloured substance that can be determined photometrically. This substance is unstable, however, and after reaching a maximum value in about 25 sec the absorbance decreases. Ethylene oxide also reacts with sodium nitroprusside to form brownish substances, but this reaction is slower, the colour not developing for 100–120 sec. If, therefore, the absorbance is measured about 25 sec after adding the reagents, any disturbance from the ethylene oxide is avoided.     

Study of the acute cardiovascular effects of several antihypertensive agents with the measurement of plasma catecholamines in mice

A highly sensitive determination method was established for catecholamines (norepinephrine (NE), epinephrine, and dopamine) with high-performance liquid chromatography-peroxyoxalate chemiluminescence reaction detection. In this study, the method was applied to mouse plasma, and it was determined that only 10 μl of mouse plasma was necessary for the selective and reproducible determination of catecholamines. Studies were then conducted in acute cardiovascular effects of sodium nitroprusside, nicardipine, captopril (angiotensin-converting enzyme (ACE) inhibitor), candesartan, and olmesartan (type 1 angiotensin receptor antagonists (AT₁ antagonists)) by this method. Sodium nitroprusside and nicardipine elevated plasma NE concentrations significantly, whereas the ACE inhibitor and the AT₁ antagonists did not change plasma NE concentrations in anesthetized mice. These results suggested that angiotensin II-induced augmentation may be mainly carried through the central baroreflex pathway.     

Metastable isonitrosyl structure of the nitroprusside anion confirmed by nuclear inelastic scattering

Nuclear inelastic scattering (NIS) measurements were performed on a guanidium nitroprusside ((CN(3)H(6))(2)[Fe(CN)(5)NO], GNP) monocrystal at 77 K after the sample was illuminated with blue light (450 nm) at 50 K to populate the two metastable states, MS(1) and MS(2), of the nitroprusside anion. A second measurement was performed at 77 K after warming up the illuminated crystal to 250 K where the metastable states decay to the groundstate. The measured spectra were compared with simulated NIS spectra that were calculated by using density functional methods. Comparison of measured and simulated spectra provides strong evidence for the isonitrosyl structure of the metastable MS(1) state proposed by Carducci et al. (Carducci, M. D.; Pressprich, M. R.; Coppens, P. J. Am. Chem. Soc. 1997, 119, 2669-2678).     

Nitroprusside-PEO enthalpic interaction as a driving force for partitioning of the [Fe(CN)(5)NO](2-) anion in aqueous two-phase systems formed by poly(ethylene oxide) and sulfate salts

Ions are known to concentrate in the salt-enriched phase of aqueous two-phase systems, with the only known exception being the pertechnetate anion, TcO(4)(-). We have discovered a second ion, nitroprusside anion (NP), which is markedly transferred from the salt phase to the polymer phase. The partitioning behavior of [Fe(CN)(5)NO](2-) anion was investigated in ATPS formed by poly(ethylene oxide) of molar mass 3350 and 35000 g mol(-1), and different sulfate salts (Na(2)SO(4), Li(2)SO(4), and MgSO(4)). On the basis of a model, the nitroprusside high affinity for the macromolecular phase was attributed to an enthalpic specific interaction between the anion and ethylene oxide unit. Partition coefficients increased exponentially with tie-line length increase, reaching values as high as 1000 and showing a relationship very dependent on the salt nature, but independent of the polymer molar mass.     

硝普钠分光光度法测定头孢他啶

建立了硝普钠分光光度法测定头孢他啶的方法。实验结果表明,在碱性条件下,头孢他啶与硝普钠以1∶2的化学计量比反应形成一种红褐色产物,其最大吸收波长为528 nm。 头孢他啶在2.50~810 mg/L浓度范围内与吸光度呈良好线性关系,线性回归方程为A=0.02704+0.00218ρ(mg/L),线性相关系数r＝0.9987,表观摩尔吸收系数ε528=1.2×103 L/(mol·cm),检测限(3σ/k)为1.38 mg/L。 本方法操作简便、快速,成功用于药品中头孢他啶含量的测定。     

Rapid screening method for methamphetamine in urine by colour reaction in a Sep-Pak C18 cartridge

A simple screening method for methamphetamine in urine by colour reaction was developed. Methamphetamine, which is quantitatively retained in a Sep-Pak C18 cartridge, is (after a clean-up procedure) coloured by Simon's reagent (consisting of sodium nitroprusside solution, sodium carbonate solution and acetaldehyde gas). The detection limit was 0.5 microgram/ml using 5 ml of urine sample. The results of the screening method agreed with those of thin-layer chromatography and gas chromatography-mass spectrometry.     

硝普钠与苯肼的反应

有氧存在下 ,硝普钠 (Na2 [Fe(CN) 5NO] )与苯肼类化合物在N ,N 二甲基甲酰胺中作用 ,发生脱肼反应 ,生成叠氮苯、苯衍生物、微量的苯胺及偶氮化合物 .对可能的反应机理进行了讨论     

A novel method for the spectrophotometric determination of cefradine by using sodium nitroprusside as chromogenic reagent

A novel method is developed for the determination of cefradine by using sodium nitroprusside as chromogenic reagent. The experiment indicates that a russety product is formed by the reaction of cefradine with sodium nitroprusside in basic solution, and the maximum absorption wavelength （λmax） of russety product is 505 rim. And the sensitization of tetradecyl benzyl dimethyl ammonium chloride for the reaction of cefradine with sodium nitroprusside is remarkable, The apparent molar absorption coefficient （5505） is 2.81 × 103 L/mol cm. The linear equation isA = 0.0657 ＋ 0.00804C （μg/mL） in the range of 1.50-55.0μg/mL of cefradine with a correlation coefficient r = 0.9992, and the detection limit is 1.38 p,g/mL. This method has been applied to determine cefradine in capsule and tablet samples.     

Assay of Phenformin Hydrochloride in Pharmaceutics by Coupling with Sodium Nitroprusside

A novel and simple spectrophotometric method for the determination of phenformin hydrochloride using sodium nitroprusside as chromogenic reagent is developed in this paper. The experiment indicates that the sodium nitroprusside can react with the phenformin hydrochloride in a basic solution to form a product with colored N‐nitrosamines. The stoichiometric ratio of phenformin hydrochloride and sodium nitroprusside is 1:3 in the product. The maximal absorption wavelength (λ_max) of the product is 520 nm, ?₅₂₀ = 2.2 × 10³ Lmol^?1cm^?1. A Good linear relationship is obtained between the absorbance (A) and the concentration (C) of phenformin hydrochloride in a wide range of 0.20‐400 μg mL^?1. The equation of the linear regression is A = 0.03461 + 0.00907C (μg mL^?1) with a linear correlation coefficient of 0.9991. The detection limit is 0.13 μg mL^?1, and the relative standard deviation (R.S.D.) is 0.19%. The method is successfully applied to the determination of phenformin hydrochloride in tablet forms, and satisfactory recoveries are obtained.     

TGA-DTA,infrared and x-ray powder diffraction studies on strontium nitroprusside and its hydrates

Dehydration data for the tetra-, di- and monohydrate of strontium nitroprusside and the vibrational behaviour of the water molecules in normal and deuterated samples agree with crystal data previously reported (for the di- and tetrahydrate as single crystals) and in this paper (monohydrate as a powder). Four distinct types of water molecules are present in the three hydrates with one type (oxygen bonded to Sr²⁺) in common. Other types are a non hydrogen-bonded molecule (dihydrate), a molecule bonded by a single hydrogen atom to the nitrogen atom of a cyanide group and a set of two molecules similarly bonded to the oxygen atom of the previous type (tetrahydrate). The spatial orientation of the NO groups of the nitroprusside ions in the tetrahydrate is confirmed by the observed dichroism of the corresponding stretching band.