Broad-area diode-laser system for a rubidium Bose-Einstein condensation experiment

We report on master-oscillator power amplification using a broad-area laser diode (BAL) emitting at a wavelength of λ =780 nm. The master oscillator is an injection-locked single-mode diode laser delivering a seeding beam of 35 mW, which is amplified in double pass through the BAL up to 410 mW. After beam shaping and spatial filtering by a single-mode fibre we obtain a clean Gaussian beam with a maximum power of 160 mW. There is no detectable contribution of the BAL eigenmodes in the spectrum of the output light. This laser system is employed for operation of a ⁸⁷Rb magneto-optical trap (MOT) and for near-resonant absorption imaging in a Bose-Einstein condensation experiment. Received: 10 April 2000 / Revised version: 13 June 2000 / Published online: 2 August 2000     

Efficient and compact intracavity-frequency-doubled Nd:GdVO4/KTP laser end-pumped by a fiber-coupled laser diode

A compact and efficient diode-pumped intracavity-frequency-doubled Nd:GdVO₄/KTP green laser is demonstrated with a flat–flat cavity design. With a 1.3 at. % Nd³⁺-doped GdVO₄ crystal and pumped at the weak-absorption peak of 806 nm, the second-harmonic output power at 532 nm was measured to be 1.95 W at an incident pump power of 8.4 W, corresponding to an optical conversion efficiency of 23.2%. The output characteristic at the fundamental wavelength of 1.063 μm was investigated with two different pump wavelengths. More than 4.5-W output power was generated when the laser was pumped at 806.2 nm. Received: 26 July 2000 / Revised version: 18 September 2000 / Published online: 7 February 2001     

Single-frequency Ti:Er:LiNbO3 distributed Bragg reflector waveguide laser with thermally fixed photorefractive cavity

The first single-frequency Ti:Er:LiNbO₃ distributed Bragg reflector waveguide laser with two thermally fixed photorefractive gratings as resonator mirrors is reported. The optically pumped (λ_p=1480 nm,120-mW incident power) laser emits up to 1.1 mW at λ_s=1561.1 nm. The threshold pump power is 70 mW. Received: 7 June 2001 / Published online: 30 October 2001     

Generation of 840 mW of red light by frequency doubling a diode-pumped 1342 nm Nd:YVO4 laser with periodically-poled LiTaO3

We report an efficient generation of red light in a periodically-poled LiTaO₃ (PPLT) crystal by extracavity single-pass frequency doubling of a diode-pumped, Q-switched Nd:YVO₄ laser at 1342 nm. The sample used in the experiment is 20 mm in length and 14.77 μm in period. An average power of 840 mW of the 671 nm red light is obtained with a 808 nm pump of 12.3 W, the overall optical-to-optical efficiency being 6.8%. The measured effective nonlinear coefficient of the sample is ∼3.8 pm/V. The high conversion efficiency and output power demonstrate that the periodically-poled crystal serving as a frequency conversion device may be used in practice to construct an all-solid-state red laser based on an extracavity single-pass quasi-continuous scheme. Received: 17 September 2001 / Revised version: 23 January 2002 / Published online: 8 May 2002     

Efficient, kHz repetition rate, gain-switched Cr:forsterite laser

We have developed a gain-switched room-temperature Cr:forsterite laser operating at repetition rates of between 1 and 34 kHz, and pumped by a continuous wave, Q-switched Nd:YAG laser. With optimised output coupling, an output pulse energy of 52 μJ was measured at 1.5 kHz repetition rate, corresponding to 11% efficiency and 13% slope efficiency. Threshold pulse energy was 53 μJ. Output power of 370 mW was obtained at 10 kHz repetition rate and 4.4 W pump power. Water cooling was not required for repetition rates up to 10 kHz. In a tunable, folded resonator, the Cr:forsterite wavelength tuned between 1173 and 1338 nm. This laser operated with maximum pulse energy of 34 μJ, efficiency of 13%, and power of 307 mW. The laser output was close to diffraction-limited with M² of 1.2. Received: 6 January 1999 / Published online: 29 July 1999     

Characterization of a high-power tapered semiconductor amplifier system

We have characterized a semiconductor amplifier laser system which provides up to 200 mW output after a single-mode optical fiber at 780 nm wavelength. The system is based on a tapered semiconductor gain element, which amplifies the output of a narrow-linewidth diode laser. Gain and saturation are discussed as a function of operating temperature and injection current. The spectral properties of the amplifier are investigated with a grating spectrometer. Amplified spontaneous emission (ASE) causes a spectral background with a width of 4 nm FWHM. The ASE background was suppressed to below our detection limit by a proper choice of operating current and temperature and by sending the light through a single-mode optical fiber. The final ASE spectral density was less than 0.1 nW/MHz, i.e. less than 0.2% of the optical power. Related to an optical transition linewidth of Γ/2π=6 MHz for rubidium, this gives a background suppression of better than -82 dB. An indication of the beam quality is provided by the fiber coupling efficiency of up to 59%. The application of the amplifier system as a laser source for atom-optical experiments is discussed. Received: 8 May 2000 / Revised version: 21 September 2000 / Published online: 7 February 2001     

Portable difference-frequency laser-based cavity leak-out spectrometer for trace-gas analysis

We report a portable mid-infrared spectrometer for trace-gas analysis which is based on an all-solid-state difference-frequency-generation laser. The spectrometer provides in situ absorption path lengths of more than 3 km by means of the cavity leak-out method, a cw variant of the cavity ring-down technique. The design, performance, and application of this spectrometer are presented. The light source utilizes difference-frequency generation in a periodically poled lithium niobate (PPLN) crystal pumped by two single-frequency solid-state lasers. A maximum power of 27 μW in the wavelength region near 3.3 μm is achieved using a pump power of 20 mW at 808 nm, a signal power of 660 mW at 1064 nm, and a 50-mm-long PPLN crystal. This corresponds to a conversion efficiency of 0.42 mW/(W² cm). We demonstrate that this portable laser system is suitable as a light source in a cavity leak-out spectrometer. We achieved a minimum detectable absorption coefficient of 1×10^-8/cm (integration time: 2 s), corresponding, for example, to a detection limit of 1 part per billion ethane. This compact trace-gas analyzer with high sensitivity and specificity is promising for various environmental and medical applications. Received: 8 April 2002 / Revised version: 28 May 2002 / Published online: 21 August 2002 RID="*" ID="*"Corresponding author. Fax: +49-211/811-3121, E-mail: muertz@uni-duesseldorf.de     

Kilohertz extreme-ultraviolet light source based on femtosecond high-order harmonic generation from noble gases

A compact, versatile table-top kilohertz source of coherent extreme-ultraviolet (XUV) radiation in the wavelength region 18–100 nm, based on high-order harmonic generation from noble gases induced by a 40-femtosecond Ti:sapphire laser system, is presented. The XUV beamline delivers at its output 10⁸ photons/s at a wavelength of 23 nm. The monochromatized XUV radiation is directly focused onto a 10^-2-mm² spot by a toroidal grating, allowing one to reach intensities higher than 10⁶ W/cm². Optimization results are presented for a new XUV-generating geometry, utilizing a ‘semi-infinite’ quasi-static gas cell and strong focusing. In those conditions, we observe an anomalous inversion between the cutoffs of argon and krypton, with the krypton spectrum extending to much higher orders than expected in an adiabatic limit. Received: 9 July 2001 / Revised version: 1 August 2001 / Published online: 7 November 2001     

Low-threshold singly-resonant continuous-wave optical parametric oscillator based on MgO-doped PPLN

We present a 532 nm-pumped singly-resonant cw optical parametric oscillator based on MgO-doped PPLN with a minimum threshold pump power of 0.3 W. The OPO with a two-mirror standing-wave cavity is optimized by using a tunable diode laser on the path of the resonant signal beam. The maximum output power is 200 mW at an idler wavelength near 1330 nm at a pump power of 2 W. We report the degradation of the output power and beam characteristics at high pump power indicating a strong thermal lensing in the crystal. The continuous tuning range of the OPO is measured to be 800 MHz which is close to 90% of the free spectral range of the OPO cavity.     

400 mW and 16.5% wavelength conversion efficiency at 488 nm using a diode laser and a PPLN crystal in single pass configuration

Continuous wave power of more than 400 mW at 488 nm has been generated by frequency doubling of 2.45 W at 976 nm obtained from a distributed Bragg reflector tapered diode laser. This results in a wavelength conversion efficiency of 16.5% and an electrical-to-optical efficiency of more than 4.5%. We used a 50 mm long periodically poled MgO:LiNbO₃ bulk crystal in single-pass configuration for the second harmonic generation. This is to the author’s knowledge the highest output power and the highest wavelength conversion efficiency at 488 nm generated by a monolithic semiconductor laser device in single pass configuration with a bulk crystal. A deviation from the quadratic dependency of the frequency doubling is explained by the decrease of the beam quality of the fundamental wave.     

Broadband Er-Yb co-doped superfluorescent fiber source

In this paper, extensive experimental results on broad-band double cladding Er³⁺-Yb³⁺ co-doped superfluorescent fiber sources (SFSs), characterizing their output power, mean wavelength, and bandwidth (BW) stability with variations of pump power, pump wavelength, and fiber temperature, have been reported. For a 55-cm fiber, SFS power from 3.7755 (maximum BW condition of more than 80 nm) to 9.1837 mW (maximum power condition, BW is about 34 nm) has been achieved. The SFS mean wavelength dependence on pump wavelength is highly pump temperature sensitive, and can be reduced to zero in a chosen pump temperature field. The intrinsic variation of the SFS mean wavelength λ_m with fiber temperature is also measured, and a linear variation from 15 to 45 °C with a slop of −0.053 nm/°C for L_f = 100 cm and −0.04 nm/°C for L_f = 55 cm is found.     

Efficient Tm：YAG Ceramic Laser at 2 μm

We demonstrate a high-efficiency continuous-wave Tm： YAG ceramic laser pumped with a Ti：sapphire laser. An output power up to 860mW is obtained under an absorbed pump power of 2.21 W at 785nm, corresponding to a slope efficiency of 42.1% and optical to optical efficiency of 22%. The measured central wavelength is 2012nm.     

Comparison of cw laser performance of Nd:KGW, Nd:YAG, Nd:BEL, and Nd:YVO4 under laser diode pumping

4 crystals under low-power laser diode end-pumping. Output power dependencies on the pump power and the pump wavelength of these diode-pumped solid state lasers were investigated. The high Nd³⁺ concentration of the Nd:KGW samples used in our measurements as well as up-conversion and exited-state absorption processes in Nd:KGW cause the reduced laser output power dependence on the pump wavelength which was experimentally observed. At pump levels up to 270 mW a slope efficiency of η_sl≈46% was reached for the Nd:KGW laser. Nd:KGW microchip laser operation with a slope efficiency of η_sl≈50% was demonstrated. Thermal lensing in Nd:KGW at pump powers up to 3 W was measured. Received: 4 August 1997     

A tunable diode-laser spectrometer for the MIR region near 7.2 μm applying difference-frequency generation in AgGaSe2

2 and two diode lasers as pump sources are presented. A single-mode Fabry–Pérot-type tunable diode laser (TDL) and an external-cavity diode laser (ECL) were combined to generate radiation in the mid-infrared region near 7.2 μm. With a TDL at a wavelength of approximately 1290 nm and an ECL emitting between 1504 and 1589 nm it was possible to carry out spectroscopic experiments concerning SO₂ at five different phasematching points between 1350 and 1400 cm^-1 by fixing the wavelength of one pump laser and tuning the wavelength of the other. With an input power of 8 mW for the single-mode Fabry–Pérot-type diode laser and 6 mW for the external-cavity laser an output power of about 10 nW was generated. Using the tuning capabilities of the external-cavity laser a spectral region up to 5 cm^-1 could be covered within one scan. Measurements of SO₂ absorption lines at low pressure demonstrate the high-resolution features of the spectrometer. Moreover, these data provide new direct experimental phasematching data for the rarely investigated spectral region at 7.2 μm. Received: 27 October 1997/Revised version: 8 May 1998     

A comparison of resonantly pumped Ho:YLF and Ho:LLF lasers in CW and Q-switched operation under identical pump conditions

Singly 0.5 at.% Ho doped crystals of YLiF₄ (YLF) and LuLiF₄ (LLF) are studied under identical pump conditions in continuous-wave (CW) and Q-switched operation. Longitudinal end-pumped CW laser performance shows Ho:LLF to have a slightly lower threshold and a slightly higher slope efficiency with respect to absorbed pump power than Ho:YLF. Both lasers were operated on π-polarization. At a cavity output coupling of 20% and a crystal length of 30 mm, the Ho:LLF (Ho:YLF) laser yielded 18.8 W (18 W) of CW output at a wavelength of 2067.8 nm (2064.0 nm) for 41.4 W (42.2 W) of absorbed pump power with a slope efficiency of 67.1% (65.6%) and an optical-to-optical efficiency of 45.4% (42.6%) with respect to absorbed pump power. With the same output coupling and a crystal length of 40 mm, the Ho:LLF (Ho:YLF) laser yielded 20.5 W (18.1 W) of CW output at a wavelength of 2067.7 nm (2064.3 nm) for 51.5 W (50.0 W) of absorbed pump power with a slope efficiency of 58.4% (55.4%) and an optical-to-optical efficiency of 39.8 (36.1%) with respect to absorbed pump power. The influence of the temperature of the cooling mount on CW laser performance was studied and showed very similar results for both laser materials. At full pump power, a slope of −155 mW/°C (−149 mW/°C) was observed for the Ho:LLF (Ho:YLF) laser with a crystal length of 30 mm. In Q-switched operation, the Ho:LLF (Ho:YLF) laser produced 37 mJ (38.5 mJ) at a repetition rate of 100 Hz with a pulse duration of 38 ns (35 ns) at a wavelength of 2053.1 nm (2050.2 nm) with a slope efficiency of 30.3% (31%) and an optical-to-optical efficiency of 14.2% (13.9%) with respect to absorbed pump power. The beam quality was nearly diffraction limited (M ²<1.1).     

All-optical wavelength tuning in Ti:PPLN Šolc filter via the photorefractive effect

We demonstrate fine-wavelength tuning of a periodically poled Ti:LiNbO₃ (Ti:PPLN) Šolc filter by use of the photorefractive (PR) effect. The center wavelength of a Ti:PPLN Šolc filter is controlled by the PR effect, which is induced by second-harmonic generation (SHG). The refractive index change caused by the PR effect is calculated from the measured shift in center wavelength from the Ti:PPLN Šolc filter. The experimental results show that all-optical fine-wavelength tuning in a Ti:PPLN Šolc filter is possible by the use of a second-order nonlinear effect and that a Ti:PPLN waveguide has much higher resistance to PR damage than a Ti:LiNbO₃ waveguide. The measured wavelength tuning rate as a function of the pump beam power is about − 0.033 nm/mW.     

Diode-pumped continuous-wave Nd:YAP laser emitting at 1073 nm based on the 4F3/2-4I11/2 transition

We describe the output performances of the 1073 nm ⁴ F _3/2 → ⁴ I _11/2 transition (generally used for a 1064 nm transition) in Nd³⁺:YAlO₃ (Nd:YAP) under in-band pumping with diode laser at the 803 nm wavelength. An end-pumped Nd:YAP crystal yielded 390 mW of continuous-wave (CW) output power for 17.8 W of incident pump power. Moreover, intracavity second-harmonic generation has also been achieved with a power of 38 mW at 536 nm by using a LiB₃O₅ (LBO) nonlinear crystal. The green beam quality factor M ² was less than 1.33. The blue power stability was less 3.5% in 4 h.     

A three-wavelength Ti:sapphire femtosecond laser for use with the multi-excited photosystem II

We have constructed a three-wavelength Ti:sapphire femtosecond laser with an independent tunable wavelength (λ₁) and two variable central wavelengths (λ₂ and λ₃) for use with the multi-excited photosystem II. Stable sub-40-fs pulses are generated. The λ₁-wavelength pulses can be tuned independently from 750 nm to 850 nm. The center wavelengths λ₂ and λ₃ can be varied from 760 nm to 840 nm. Received: 14 April 2000 / Revised version: 5 September 2000 / Published online: 27 April 2001     

Dye laser pumped, continuous-wave KTP optical parametric oscillators

4 (KTP) optical parametric oscillators (OPOs) with pump and idler resonant cavities. With a linear two-mirror cavity the pump power at threshold was 70 mW. The single-frequency signal and idler output wavelengths were tuned in the range of 1025 to 1040 nm and 1250 to 1380 nm by tuning the dye laser in the range of 565 to 588 nm. With a dual three-mirror cavity the threshold was 135 mW. Pumped by 500 mW of 578 nm radiation the 1040 nm single-frequency signal wave output power was 84 mW. Power and frequency stable operation with a spectral bandwidth of less than 9 MHz was obtained by piezo-electrically locking the length of the pump resonant cavity to the dye laser wavelength. Similar performance was achieved by placing the idler resonant OPO inside the resonator of the dye laser. With this system power stable and single-frequency operation was achieved with a spectral bandwidth of less than 11 MHz for the idler wave. Received: 3 February 1998/Revised version: 9 March 1998     

Online monitoring of ethane traces in exhaled breath with a difference frequency generation spectrometer

We report a transportable mid-infrared laser cavity leak-out spectrometer for online detection of trace gases. The laser spectrometer is based on continuous-wave difference-frequency generation in the wavelength region around 3 μm. Sensitive spectroscopic trace gas monitoring was achieved using a high-finesse ring-down cavity. For difference-frequency generation, we use a periodically poled lithium niobate (PPLN) crystal, pumped by a Nd:YAG laser (signal wave) and a diode laser (pump wave) with a tapered amplifier. A maximum power of 280 μW near λ=3.3 μm is achieved using a pump power of 180 mW at 807 nm, a signal power of 890 mW at 1064.46 nm, and a 50-mm-long PPLN crystal. The resulting system proved to be a unique tool with high sensitivity and specificity for rapid and precise breath testing. We demonstrate spectroscopic online monitoring of ethane traces in exhaled human breath with a precision of 270 parts per trillion (1σ) and a time resolution of 1 s. PACS 42.62.Be; 42.60.-v; 07.57.Ty