30%亚硫酸氢钠溶液样品中Cl-和SO2-4的同时测定

建立了采用离子色谱测定30%亚硫酸氢钠溶液样品中的氯化钠和硫酸钠含量的新方法。采用IonPac AS14分析柱,选择三乙醇胺为亚硫酸氢钠的稳定剂,以丙酮为有机改进剂,淋洗液组成为1.5 mol/L Na2CO3-3.5 mol/L NaHCO3-10% （体积分数）(CH3)2CO,流速为1.0 mL/min,抑制电导检测。实验结果表明,氯离子、硫酸根离子分别在0.05~1.5 mg/L,0.20~15 mg/L时,其峰面积与质量浓度呈线性关系,相关系数均大于0.999,检出限分别为0.01 mg/L和0.03 mg/L。该法用于实际样品分析,操作便捷,结果可靠。     

NaHSO3溶液中SO 4^2-离子色谱峰的分叉现象及其测定

首次发现并探讨了30%(w)亚硫酸氢钠水溶液中硫酸根离子色谱法峰分叉现象.选择0.1%TEA溶液为亚硫酸氢钠稳定剂,分析柱为IonPac AS14,采用丙酮为有机改进剂,确定淋洗液组成为1.5 mol/L Na2CO3-3.5 mol/LNaHCO3-10%(CH3)2CO,流速为1.0mL/min.抑制电导检测,在线性范围内硫酸根检出限为0.05μg/g,相关系数大于0.999,从而建立了30%亚硫酸氢钠溶液中硫酸钠测定新方法.用于实际样品分析,操作便捷,结果可靠.     

NaHSO3溶液中SO2- 4离子色谱峰的分叉现象及其测定

首次发现并探讨了30%(w)亚硫酸氢钠水溶液中硫酸根离子色谱法峰分叉现象.选择0.1%TEA溶液为亚硫酸氢钠稳定剂,分析柱为IonPac AS14,采用丙酮为有机改进剂,确定淋洗液组成为1.5 mol/L Na2CO3-3.5 mol/LNaHCO3-10%(CH3)2CO,流速为1.0mL/min.抑制电导检测,在线性范围内硫酸根检出限为0.05μg/g,相关系数大于0.999,从而建立了30%亚硫酸氢钠溶液中硫酸钠测定新方法.用于实际样品分析,操作便捷,结果可靠.     

抑制型离子色谱法检测植物样品中植酸根及磷酸根的含量

采用抑制型高效离子色谱法检测植物样品中植酸根和磷酸根的含量。样品用1%(质量分数)三氯乙酸处理,离心沉降 后取上清液经0.45 μm微孔滤膜过滤后注入离子色谱仪。用0.22 mol/L氢氧化钠水溶液、水和50%(体积分数)异丙醇水 溶液进行梯度淋洗,经微膜抑制后检测其电导率。实验结果表明,植酸根与磷酸根的检测不受F-、Cl-、SO2-4、NO-3、CC l3CO-2等阴离子的干扰。植酸根、磷酸根的质量浓度分别为5~400 mg/L和5~500 mg/L 时与峰面积呈良好的线性关系(r2分别为0.9994和0.9999),检出限分别为3.5 mg/L和1.5 mg/L;植酸根、磷酸根的平均 回收率分别为99.8%和98.4%,检测结果的相对标准偏差分别为1.98%和2.09%。     

氧弹燃烧-离子色谱法测定电子产品连接线中的卤素

建立了氧弹燃烧法处理电子产品连接线,离子色谱测定样品中卤素的分析方法。选用TSK-gelSuperIC-AZ阴离子分析柱,以NaHCO3(7.5mmol/L)+Na2CO3(1.1mmol/L)为流动相等度洗脱,抑制电导检测。结果表明,该条件下F-浓度在0.02～2mg/L,Cl-和Br-浓度在0.05～5mg/L范围内峰面积与浓度的线性关系良好(r>0.999),实际样品中卤素回收率为90.52%～97.24%,样品测定结果相对标准偏差均为0.73%～2.01%(n=5)。应用氧弹燃烧-离子色谱法测定电子产品连接线中的卤素离子,方法简便、快捷,测定结果准确。     

测定驱油体系中碱度的流动注射分光光度法

采用流动注射分析技术，以酸碱指示剂－－间硝基酚溶液作载流，实现了三元复合驱油体系中碱的测定；该法可测定10－600mg/L NaOH(强碱），20－1400mg/L Na2CO3(弱碱）；方法的检出限为0．5mg/L NaOH,1mg/L,Na2CO3；对含量为200mg/L的样品测定6次的相对标准偏差为0.6%(NaOH),0.5%(Na2CO3);测定速率每小时达94个样；该法也适用于其它无机碱、有机碱的测定。     

高效液相色谱-间接紫外检测法分析吡咯烷离子液体阳离子的研究

采用反相C_(18)色谱柱和紫外检测器,建立了吡咯烷离子液体阳离子的高效液相色谱-间接紫外检测分析方法。咪唑离子液体作为流动相的添加剂,既是背景紫外吸收试剂,又是改善分析物分离效果的有效组分。流动相中加入离子对试剂庚烷磺酸钠,可较好地改善吡咯烷离子液体阳离子的分离效果。在最佳色谱条件下,3种吡咯烷离子液体阳离子([MEPy]~+、[MPPy]~+和[MBPy]~+)可在13 min内得到有效的分离检测,[MEPy]~+、[MPPy]~+、[MBPy]~+的线性范围分别为0. 6～100 mg/L、1. 3～230 mg/L和3. 6～250 mg/L,相关系数(r)均大于0. 999,检出限分别为0. 2、0. 4、1. 1 mg/L。将该方法应用于实验室合成的同系物吡咯烷离子液体样品的检测,加标回收率为92. 2%～96. 7%。该方法准确、可靠,是一种有效分离和检测吡咯烷离子液体阳离子的实用方法。     

双电极法现场快速检测地下水和湖水中碳酸氢根和碳酸根

地下水和湖水中碳酸氢根( HCO-3)和碳酸根( CO2-3)含量是地球化学碳行为和碳循环的重要表征,但两种离子的浓度易受环境影响而改变,因此,地下水和湖水中HCO-3和CO2-3真实含量的测定一直是个难题。实验利用CO2的水解平衡,通过pH电极和二氧化碳电极联用,建立了HCO-3和CO2-3现场快速测定的新方法,解决了地下水和湖水中HCO-3和CO2-3真实含量的测定难题。研究结果表明,在pH=4.8±0.1的底液中, HCO-3和CO2-3的线性范围分别为0.027~570 mg/L和1.25×10-8~39.7 mg/L。共存的金属离子、强酸阴离子(K+、Na+、Mg2+、Cl-、SO2-4,100 mg/L)、弱酸阴离子和弱酸(HSO-3、NO-2、HOAc,50 mg/L)对测定干扰小于5%。实际水样加标实验回收率在95.2%~99.2%之间,相对标准偏差为2.6%~3.7%。与酸碱滴定法进行对比,本方法的准确性良好。但方法受温度影响,因此标准溶液与样品应在同一温度下测量。总体而言,双电极法灵敏、快速、经济且电极携带方便、操作简单、对环境要求不高,十分适合现场和室内一般自然水体的快速检测。本方法已成功应用于青海省地下水和青海湖湖水中HCO-3和CO2-3的现场测定。实验表明,海东地区地下水样品pH在6.4~7.4之间,HCO-3含量为234~4096 mg/L,CO2-3含量为0.16~1.89 mg/L;青海湖湖水样品pH≈8.7,HCO-3含量范围在1.36~1.86 g/L,CO2-3含量在32.3~43.9 mg/L,与文献结果吻合。     

离子排斥色谱法测定甘油催化氧化产物中的H2CO3和HCOOH

建立了测定甘油催化氧化产物中H2CO3和HCOOH的离子排斥色谱分析方法。采用离子排斥柱分离,分别用纯水和4 mmol/L HCl作流动相进行H2CO3和HCOOH的分析。检测方式为非抑制电导检测。实验结果显示,H2CO3和HCOOH工作曲线的线性范围为2～100 mg/L和6.23～124.6 mg/L,检出限分别为0.45 mg/L和2.49 mg/L(S/N=3)。H2CO3的保留时间和峰面积的相对标准偏差分别为0.07%和4.0%,HCOOH的保留时间和峰面积的相对标准偏差分别为0.09%和2.2%。方法已用于甘油催化氧化产物中H2CO3和HCOOH的分析。     

离子色谱法同时测定脱硫海水中的SO_4~(2-)和SO_3~(2-)

采用离子交换色谱法同时定量分析脱硫海水中SO_4~(2-)和SO_3~(2-)。0.01 mol/L EDTA和0.10×10~(-3) mol/L NaOH混合溶液用于除去海水样品中Ca~(2+)、Mg~(2+)干扰,加入0.5%的甲醛溶液防止SO_3~(2-)氧化为SO_4~(2-)。实验采用DINOEX AS-9HC阴离子交换柱作分离柱,以9.00×10~(-3) mol/L Na_2CO_3溶液为淋洗液,电导检测器检测。方法线性范围为5.00~100.00 mg/L,加标回收率为97.85%~103.99%,相对标准偏差(RSD)为0.20%~2.07%。SO_3~(2-)的检出限为0.03mg/L,SO_4~(2-)的检出限为0.04mg/L。结果表明,本方法可以有效消除海水中Ca~(2+)、Mg~(2+)对低浓度SO_3~(2-)、SO_4~(2-)测定的干扰,可同时实现海水脱硫体系中SO_3~(2-)、SO_4~(2-)的定量分析。     

Osmotic and activity coefficients of aqueous bile salt solutions at 25, 37, and 45°C

Osmotic coefficients measured by vapor pressure osmometry are reported for aqueous bile salt solutions at 25, 37, and 45°C. Solute activities decrease rapidly with increasing concentration due to premicellar association and micelle formation. In all cases, activities of the dihydroxy bile salts are lower than those of the trihydroxy bile salts. Osmotic coefficients and activity coefficients increase with increasing temperature. It is suggested that hydrophobic forces contribute substantially to the stability of primary bile salt aggregates and micelles.     

胆酸盐在酸性介质中自聚集作用的共振瑞利散射光谱及其分析应用研究

研究了牛磺胆酸钠、甘牛胆酸钠、胆酸钠和脱氧胆酸钠等四种胆酸盐在酸性介质中的聚集作用对共振瑞利散射光谱的影响及其分析应用. 结果表明: 在一定浓度的HCl, H₂SO₄或HNO₃溶液中, 四种胆酸盐均能自聚集形成粒径增大的聚集体. 该聚集体能导致溶液RRS显著增强, 并产生了新的RRS光谱. 不同胆酸盐在同种介质中的反应产物具有相似的光谱特征, 最大RRS波长分别位于349 (HNO₃介质), 359 (H₂SO₄介质)和369 nm (HCl介质). 在一定范围内, 胆酸盐的浓度与散射强度(ΔI_RRS)成正比. 对于不同的体系其检出限在12.0～21.8 ng/mL之间. 方法灵敏度高, 选择性较好, 而且十分简便快速. 可用于市售蛇胆川贝液和血清样品中胆酸盐的测定.     

Facile Stabilization of the Sodium Metal Anode with Additives: Unexpected Key Role of Sodium Polysulfide and Adverse Effect of Sodium Nitrate

Sodium metal is an attractive anode for next‐generation energy storage systems owing to its high specific capacity, low cost, and high abundance. Nevertheless, uncontrolled Na dendrite growth caused by the formation of unstable solid electrolyte interphase (SEI) leads to poor cycling performance and severe safety concerns. Sodium polysulfide (Na₂S₆) alone is revealed to serve as a positive additive or pre‐passivation agent in ether electrolyte to improve the long‐term stability and reversibility of the Na anode, while Na₂S₆‐NaNO₃ as co‐additive has an adverse effect, contrary to the prior findings in the lithium anode system. A superior cycling behavior of Na anode is first demonstrated at a current density up to 10 mA cm^?2 and a capacity up to 5 mAh cm^?2 over 100 cycles. As a proof of concept, a high‐capacity Na‐S battery was prepared by pre‐passivating the Na anode with Na₂S₆. This study gives insights into understanding the differences between Li and Na systems.     

Mechanism of glass ampoule breakage prevention during the freeze-drying process of sodium thiopental lyophilization products on addition of sodium chloride

Glass ampoule breakage during the freeze-drying process was prevented by the addition of sodium chloride to the formulation of lyophilization products of sodium thiopental. In order to clarify the ampoule breakage prevention mechanism, the physicochemical behavior of the freeze-drying process was monitored by simultaneous XRD-DSC measurements and thermal mechanical analysis (TMA). During the freezing process of formulated solution, the smaller heat of fusion of crystallized ice with the addition of sodium chloride was observed in comparison to that without sodium chloride. Although a greater amorphous portion remained, a higher crystal habit of hexagonal ice was reproducibly observed in the XRD patterns with the addition of sodium chloride during the freezing process. In the measurement of TMA, the scattering of the thermal expansion rate of formulated solution was significantly reduced by the addition of sodium chloride. These observations indicated that the addition of sodium chloride minimized the scattering of the thermal expansion rate and might be a cause for the inhibition of glass ampoule breakage during the freeze-drying process.     

Studies on the Effects of Salt and Surfactant in Wet Phase Separation of Polysulfone

This study investigates the effect of additives in the nonsolvent water in terms of cloud point during the phase inversion of Polysulfone (PS) in dimethyl formamide (DMF). The exponential pattern is observed with PS concentration (0.2 to 0.6% (w/w)). It needs a low amount of water to get the cloud point at low temperature. The cloud point varied with the nature of water matrix and depended on the amount of salt, as well as the PS amount. The presence of salts (sodium chloride and sodium sulfate) lowers the cloud point of the solution. The network distribution of the particles at the cloud point is disturbed in the presence of salt. The requirement is more for Sodium lauryl sulfate (SLS) added water to reach the cloud point in the low range of PS solution up to 0.3% PS (w/w). The morphological and distribution pattern of PS particles are very different compared to PS particles produced from pure water. XRD study of PS particles produced from the mixed water system reflects relatively more amorphous character with respect to PS particles from pure water. The presence of both surfactant and salts in water systems also influences the cloud point in synergistic manner.     

Crystal Structure of a New Form of Sodium Octoborate β-Na2B8O13

Single crystals of a new form of sodium octoborate, β-Na₂B₈O₁₃, were obtained fortuitously from a complex Na₂O-B₂O₃-P₂O₅ mixture, and studied. The compound is monoclinic, space group P2₁/c; the unit cell parameters are a=11.731(4) Å, b=7.880(3) Å, c=10.410(4) Å, β=99.883(3)°; Z=4. The crystal structure was solved from 1653 reflections until R₁=0.0444; it consists of two infinite, independent, and interleaved boron-oxygen networks containing a complex borate anion (B₈O₁₃)²⁻ formed by six BO₃ triangles (Δ) and two BO₄ tetrahedra (T), which can be viewed as a B₅O₁₀ group linked to a B₃O₇ group; this leads to a Fundamental Building Block (FBB) with the shorthand notation: 8: ∞³ [(5:4Δ+T)+(3:2Δ+T)]. This FBB is identical to that described in other octoborates such as α-Na₂B₈O₁₃ and Ag₂B₈O₁₃. However, some subtle differences exist in the interlinking of the octoborate anions found in these three compounds, which explains their different structure and unit cell parameters.     

自动电位滴定法测定工业碳酸钠中氯化钠含量

采用自动电位滴定法,用硝酸银标准溶液作为滴定剂,测定工业碳酸钠中氯化钠含量。方法检出限为0.13mg/L,不同含量氯化钠样品加标回收率为99.7%~100.3%,相对标准偏差(n=5)为0.17%~2.0%,方法简单、快速,精密度和准确度高,适合大批量快速分析样品。     

毛细管电泳法测定注射用头孢哌酮钠他唑巴坦钠中目标成分

建立了毛细管区带电泳法同时测定注射用头孢哌酮钠他唑巴坦钠中目标成分含量的方法。采用石英毛细管(75 cm×75 μm i.d.,有效长度63 cm),以40 mmol/L硼砂溶液为背景电解质(BGE),以氢氯噻嗪为内标,分离电压12.0 kV,检测波长220 nm,重力进样10 s(高度10 cm)。实验结果表明,头孢哌酮钠与他唑巴坦钠分别在0.25～3.96 g/L和0.062～0.99 g/L范围内呈良好的线性关系,相关系数(r)分别为0.9995和0.9996。精密度和重复性均良好,相对峰面积的相对标准偏差(RSD)均小于3%,制剂在208 min内稳定,回收试验结果符合方法学要求。该方法简单、准确、耗费少、污染小,可用于注射用粉针剂头孢哌酮钠他唑巴坦钠中头孢哌酮钠和他唑巴坦钠的定量分析。     

复合硝基酚钠盐的胶束电动力学毛细管色谱分析

本文在自行研制的高效毛细管电泳仪上建立了复合硝基酚钠盐的胶束电动力学毛细管色谱分析方法。用５０ｍｍｏｌ／Ｌ十二烷基硫酸钠、ｐＨ＝９．０的硼酸盐缓冲溶液，在２０ｋＶ电压下分离了５－硝基愈创木酚钠、对硝基酚钠、邻硝基酚钠，此法用于Ａｔｏｎｉｋ型植物生长调节剂的定量分析，相对偏差小于２％，回收率在１０１％￣１０５％之间。     

铝和碳酸钠溶液反应的探讨

通过实验观察到铝和碳酸钠溶液可以反应并冒出气泡,为此,设计了几组对比实验并进行了理论分析。发现常温下,铝与浓度在6.5×10-6 mol/L以上的碳酸钠溶液（pH ≥ 8.8）是可以反应的,而且生成四羟基合铝酸钠、碳酸氢钠和氢气。