鲁米诺在氧化铟锡玻璃上的电聚合及电化学发光性能研究

研究了鲁米诺在氧化铟锡(Indium-tinoxide,ITO)玻璃上的电聚合。通过循环伏安和紫外吸收光谱表征,在酸性条件下可以实现鲁米诺对ITO电极的电聚合修饰,聚合在ITO玻璃表面的鲁米诺保持其良好的电化学发光性能,考察了此修饰电极的性能以及相关因素对聚合膜的电化学发光强度的影响。     

基于碳纳米管修饰电极的胆碱电化学发光生物传感器研制

在碳纳米管(CNTs)和K3Fe(CN)6修饰的铂电极上吸附固定胆碱氧化酶,以鲁米诺为发光试剂,研制了胆碱电化学发光(ECL)生物传感器.CNTs可有效提高电极表面的电荷传输能力、提高电极表面的生物相容性和对酶分子的固载能力;K3Fe(CN)6对酶活性具有激活作用,同时对H2O2增敏的鲁米诺ECL有增强作用,均有利于提...     

三维有序结构的金掺杂纳米TiO_2修饰电极用于H_2O_2的测定

在ITO玻璃表面构建了三维有序多孔结构的金掺杂纳米Ti O2薄膜(3DOM GTD/ITO),同时制备了一种细胞色素c(Cyt c)酶生物传感器(Cyt c/3DOM GTD/ITO)。通过透射电镜(TEM)、扫描电镜(SEM)对修饰电极进行表征。紫外-可见光谱实验表明吸附在GTD上的Cyt c能够保持其生物活性,二级结构未被破坏。同时研究了Cyt c在3DOM GTD/ITO修饰电极表面的直接电化学及对H2O2的电催化行为。结果显示,Cyt c在3DOM GTD/ITO修饰电极上有显著的直接电化学响应,峰电流与扫描速度呈线性关系,说明该电极过程是表面电化学控制过程。Cyt c/3DOM GTD/ITO修饰电极对H2O2具有良好的催化性能,线性范围为3.0×10-7~1.70×10-5mol/L,检出限为3.6×10-8mol/L(S/N=3),响应时间为5 s,且该修饰电极具有较好的重现性和稳定性。     

电化学发光生物传感器研制

文献报道均强调鲁米诺的电化学发光(ECL)必须在强碱性介质(NaOH,pH 12～13)中实施.实验发现完全可以在中性介质中实施其电化学发光分析,这对开展生物分子的分析是十分有利的.研究中采用的是以多种增敏技术来提高中性介质中鲁米诺电化学发光的效率,如使用无机、有机和纳米增敏剂及电极表面修饰等.     

有机钌螯合物/TiO_2杂化膜修饰电极上Pt纳米团簇的光电流增强效应

利用LB膜技术可控制备了纳米单层和多层的二氧化钛-有机钌螯合物杂化膜,并研究了上述无机-有机杂化膜修饰电极在Pt纳米团簇敏化后的光电流增强效应.实验结果表明:(1)纳米单层TiO2/[Ru(phen)2(dC18bpy)]2+(简称为TiO2-Ru)杂化膜的平均厚度为(3.6±0.5)nm;(2)在光照条件下TiO2-Ru杂化膜能有效催化还原[Pt(NH3)6]4+形成粒径位于20～160nm之间的Pt纳米团簇;(3)Pt纳米团簇的引入消除了金属钌螯合物中配体对电子传递的阻碍作用,改变了电子传递途径,从而有效减少了电子空穴对的复合,提高了Pt纳米团簇敏化的n层杂化膜修饰电极(ITO/(TiO2-Ru)n/Pt)在支持电解质中的光电流.与纳米单层TiO2-Ru杂化膜修饰的ITO电极(ITO/TiO2-Ru)相比,当工作电压为900mV时,ITO/TiO2-Ru/Pt在0.1mol·L-1的NaClO4电解质溶液中和光照(λ360nm)条件下,单位面积的光电流提高了约5倍;(4)ITO/(TiO2-Ru)n/Pt电极光电流的大小与杂化膜的层数密切相关,当TiO2-Ru杂化膜的层数从一层、二层增加到四层时,光电流呈现先升高后下降行为,这表明ITO/(TiO2-Ru)n/Pt电极的电子传递过程直接通过非电活性的二氧化钛纳米单层进行.     

铂溶胶修饰电极对鲁米诺电化学发光的增敏作用

用化学还原法制备了纳米铂溶胶,透射电鏡显示其粒径约为5 nm,经过电化学沉积可将铂溶胶修饰于铂盘电极上。在中性介质中,铂溶胶修饰电极对溶液中鲁米诺的电化学发光具有明显的增敏作用,且具有较好的稳定性。维生素C对此增敏的电化学发光有强烈的猝灭作用。因此,利用该修饰电极可测定痕量维生素C。灵敏度极高,检出限为2.0×10-13mol/L,并实现了片剂的检测,方法准确、可靠。     

Pd纳米粒子敏化的纳米单层TiO_2-Ru(Ⅱ)螯合物修饰电极对单磷酸鸟苷的电催化氧化行为

利用LB膜技术可控制备了纳米单层的二氧化钛-有机钌螯合物杂化膜,并研究了上述无机-有机杂化膜修饰电极在Pd纳米粒子敏化后对单磷酸鸟苷(GMP)的电催化氧化行为.实验结果表明:(1)纳米单层TiO2/[Ru(phen)2(dC18bpy)]2+(简称为TiO2-Ru)杂化膜的平均厚度为(3.2±0.5)nm;(2)在光照条件下TiO2-Ru杂化膜能有效催化还原[Pd(NH3)4]2+形成粒径位于20～200nm之间的Pd纳米粒子;(3)纳米单层TiO2-Ru/Pd杂化膜能高效催化氧化具有供电子能力的单磷酸鸟苷(GMP),与纳米单层TiO2-Ru杂化膜修饰的ITO电极(ITO/TiO2-Ru)相比,当工作电压为1200mV时,ITO/TiO2-Ru/Pd电极在含有1×10-3molL-1GMP的磷酸盐缓冲液中,单位面积的催化氧化电流提高了约36倍;(4)Pd纳米粒子的引入消除了金属钌螯合物中配体对电子传递的阻碍作用,改变了电子传递途径,从而有效减少了电子空穴对的复合,提高了杂化膜修饰电极(ITO/TiO2-Ru/Pd)的电子传递效率.     

纳米TiO_2膜修饰电极异相电催化还原马来酸

通过电化学合成前驱体和溶胶 -凝胶法在Ti表面修饰一层纳米TiO2 膜 ,SEM ,XRD测试表明晶型为锐钛矿型 ,晶粒平均尺寸为 2 5nm .采用循环伏安法、循环方波伏安法和电解合成法研究了纳米TiO2 膜电极在硫酸介质中的氧化还原行为以及对马来酸 (maleicacid)还原的电催化活性 .结果表明 ,纳米TiO2 膜电极在阴极扫描时有两对可逆氧化还原峰 ,可逆半波电位Er1/ 2 分别为 -0 .5 3V和 -0 .92V (vs .SCE ,扫描速度 0 .0 5V·s-1) ,对应于TiO2 /Ti2 O3 和TiO2 /Ti(OH) 3 两个氧化还原电对的可逆电极过程 .其中TiO2 /Ti2 O3 电对对马来酸具有异相电催化还原活性 ,纳米TiO2 膜中的TiⅣ/TiⅢ 氧化还原电对作为媒质间接电还原马来酸为丁二酸 (butanediacid) ,反应机理为电化学偶联随后化学催化反应 (EC′)机理 .     

三维有序金掺杂纳米TiO_2修饰电极用于抗肿瘤药物与DNA相互作用的研究

利用模板法在氧化铟锡(ITO)电极表面制备了三维有序多孔结构的金掺杂纳米Ti O2薄膜修饰电极(3DOM GTD/ITO),并在此修饰电极上成功固定小牛胸腺DNA(ct DNA),从而构建了一种新型的DNA生物传感器(DNA/3DOM GTD/ITO),并通过透射电镜(TEM)、扫描电镜(SEM)对修饰电极的表面形貌进行表征。采用电化学交流阻抗(EIS)法研究了ct DNA在3DOM GTD/ITO修饰电极表面的固定情况,结果表明,ct DNA已被成功地固定在3DOM GTD/ITO修饰电极表面。采用循环伏安法、微分脉冲伏安法等电化学方法研究了抗肿瘤药物槲皮素(Qu)在3DOM GTD/ITO修饰电极表面的电化学性质及与ct DNA的相互作用。结果表明,Qu在3DOM GTD/ITO修饰电极表面有1对准可逆的氧化还原峰,其氧化还原反应为2电子和2质子的转移过程。Qu可与固定在修饰电极上的ct DNA发生较强的结合作用,其结合常数(K)为3.61×106L/mol。循环伏安实验、紫外-可见吸收光谱、分子荧光光谱、圆二色性光谱均表明Qu与ct DNA之间的相互作用模式为嵌插作用。Qu与ct DNA的碱基结合具有序列选择性,对Qu与聚(d G-d C)及聚(d A-d T)的结合常数进行计算,得到结合常数比K(d G-d C)/K(d A-d T)=3.5,表明Qu与ct DNA发生嵌插作用时更倾向于结合在GC富集区域。     

氧化石墨烯/硒化镉修饰电极电化学发光法测定铅(Ⅱ)

将氧化石墨烯(GO)和CdSe复合物修饰到金电极表面,得到了GO/CdSe修饰电极,研究了其电化学发光性质。结果表明,在强碱性溶液中,GO/CdSe修饰电极在鲁米诺溶液中会产生明显的电化学发光信号,而Pb~(2+)对该体系的电化学发光信号有较强的增敏作用,据此建立了检测Pb~(2+)的新方法。考察了GO/CdSe复合物的比例、缓冲溶液的pH、静置时间等条件对ECL强度的影响。在优化的实验条件下,Pb~(2+)浓度在1.0×10-11~1.0×10-7mol/L范围内与相对ECL强度呈现良好的线性关系。检测限(S/N=3)为3.3×10~(-12)mol/L,并用于人工湖水样中Pb~(2+)的测定。     

新型CNT/nano-TiO_2复合膜电极的制备及其异相电催化性能

采用溶胶-凝胶法制备了碳纳米管/纳米TiO2(CNT/nano-TiO2)复合溶胶,通过提拉法将复合溶胶涂覆在Ti基体上制得CNT/nano-TiO2复合膜修饰电极(C电极),其电化学性能经循环伏安、计时库仑、交流阻抗谱(EIS)等方法研究.研究结果表明,CNT可阻碍nano-TiO2粒子团聚.在循环伏安图中,C电极的氧化还原峰电流比nano-TiO2膜修饰电极(P 电极)的高出两倍多.通过对草酸溶液的异相电催化反应进一步证明C电极比P电极具有更高的电催化活性,而且对双氧水也有很强的异相电催化还原能力.     

纳米TiO2-Pt修饰电极的制备及电催化活性

采用电化学合成前驱体直接水解法和电沉积法制备高活性纳米TiO2-Pt修饰电极，并使用扫描电子显微镜(SEM)对电极的表面形貌和结构进行了表征; 通过循环伏安法研究了纳米TiO2-Pt修饰电极在H2SO4溶液中的电化学行为以及对Mn2＋氧化为Mn3＋的电催化活性. 结果表明,纳米TiO2的晶粒大小约30 nm,修饰在纳米TiO2膜表面的Pt微粒呈现单分散状态,平均粒径约60 nm,纳米TiO2-Pt修饰电极的电化学性能优于纯Pt电极,对Mn2＋的电氧化具有高催化活性,非均相无隔膜电解氧化Mn2＋生成Mn3＋平均电流效率可达86％.     

一种难溶多金属氧酸盐配位聚合物的重构与表征

利用电沉积法将不溶于常规无机和有机溶剂的多金属氧酸盐基的配位聚合物1, [{La(H₂O)₅·(dipic)}{La(H₂O)(dipic)}]₂{Mo₈O₂₆}·10H₂O溶解于离子液体[RMIM][HT]或[RMIM][HP]中, 在恒电位下电解, 得到多金属氧酸盐基的配位聚合物膜. 应用红外光谱、X射线光电子能谱和XRD粉末衍射等方法研究多金属氧酸盐基配位聚合物膜的结构, 发现其与多金属氧酸盐基配位聚合物有相同的结构. 实现了多金属氧酸盐基配位聚合物在电极上的重构设计以及多金属氧酸盐基的配位聚合物的二次加工成型.     

The promotion effect of titania nanoparticles on the direct electrochemistry of lactate dehydrogenase sol-gel modified gold electrode

The promotion effect of titania nanoparticles (nano-TiO(2)) on the direct electron transfer between lactate dehydrogenase (LDH) and the silica sol-gel modified gold electrode was investigated by adding nano-TiO(2) (50 nm) in the modification process. This nano-TiO(2)-LDH electrode showed a pair of quasi-reversible cyclic voltammetry peaks with the formal potential of 70 mV (vs. SCE). Compared to the previous result of LDH modified electrode with only an irreversible cathodic peak, an anodic peak appeared and the cathodic peak potential shifted to the positive direction on this nano-TiO(2)-LDH electrode, which demonstrated that the direct electrochemistry of LDH was enhanced by nano-TiO(2). We supposed that the direct electrochemistry of LDH may be due to the redox reaction of some electroactive amino acids in the LDH molecule. The surface morphologies of electrodes characterized by SEM indicated that LDH was successfully immobilized on the sol-gel matrix and also had some interactions with nano-TiO(2). This electrode can be used as a biosensor for the determination of lactic acid. The calibration range of lactic acid was from 1.0 to 20 micromolL(-1) and the detection limit was 0.4 micromolL(-1). Meanwhile, the small K(m)(app) value (2.2 micromolL(-1)) suggested that LDH possessed high enzymatic activity and good affinity to lactic acid owing to the promotion effect of nano-TiO(2).     

Chemical Adsorption onto an ITO Substrate of Single‐Wall Carbon Nanotube Functionalized by Carboxylic Groups as an Efficient Support for Electrocatalyst

A single‐wall carbon nanotube functionalized by carboxylic groups (SWNT‐CA) was found to be adsorbed on an indium tin oxide (ITO) electrode by chemical interaction between carboxylic groups and the ITO surface. The adsorption experiments indicated that the narrow pH conditions (around pH 3.0) exist for its adsorption which is restricted by preparation of stable fluid dispersion (favorable at higher pH) and by the chemical interaction (favorable at lower pH). Atomic force microscopic (AFM) measurements suggest that fragmented SWNT‐CA are adsorbed, primarily lying on the surface. Electrochemical impedance analysis indicated that an electrochemical double layer capacitance of the SWNT‐CA/ITO electrode is considerably higher than that for the ITO electrode, suggesting that the interfacial area between the electrode surface and the electrolyte solution is enlarged by the SWNT‐CA layer. Pt particles were deposited as a catalyst on the bare ITO and SWNT‐CA‐coated ITO (SWNT‐CA/ITO) electrodes to give respective Pt‐modified electrodes (denoted as a Pt/ITO electrode and a Pt/SWNT‐CA/ITO electrode, respectively). The cathodic current for the Pt/SWNT‐CA/ITO electrode was 1.7 times higher than that for the Pt/ITO electrode at 0.0 V, showing that the Pt/SWNT‐CA/ITO electrode works more efficiently for O₂ reduction at 0.0 V due to the SWNT‐CA layer. The enhancement by the SWNT‐CA layer is also effective for electrocatalytic proton reduction. It could be ascribable to the enlarged interfacial area between the electrode surface and the electrolyte solution.     

溶胶-凝胶法制备纳米TiO2/丝素复合膜及结构性能研究

用溶胶凝胶法制备不同比例纳米TiO₂改性再生蚕丝丝素蛋白复合膜. UV和AFM测试结果表明, 该丝素膜中纳米TiO₂均匀分散在丝素中, TiO₂粒径约为80 nm; 同时该丝素膜的结构和热性能用FTIR, XRD, EDS, TGA和DTG进行表征. XRD测试结果表明, 随着纳米TiO₂的加入, 复合丝素膜的结晶结构从Silk I向Silk II转化, 但当纳米TiO₂的加入超过一定量时, 又破坏复合丝素膜的结晶结构; FTIR和EDS测试结果表明, TiO₂与丝素形成较好的键合; TGA和DTG测试表明复合丝素膜的热转变温度相比于纯丝素膜有所提高.     

谷胱甘肽在nano-TiO2-咖啡酸复合修饰碳糊电极上的电催化氧化及电分析方法

研究了还原型谷胱甘肽( CSH)在nano-TiO2 -咖啡酸(CFA)复合修饰碳糊电极(nano-TiO2 - CFA/CPE)上的电催化氧化行为,并进行了测定.结果表明,GSH在CPE和nano-TiO2/CPE上的直接电化学氧化过程十分迟缓,nano-TiO2 - CFA/CPE比CFA/CPE对GSH的电化学氧...     

Surface Engineering of ITO Substrates to Improve the Memory Performance of an Asymmetric Conjugated Molecule with a Side Chain

Organic multilevel random resistive access memory (RRAM) devices with an electrode/organic layer/electrode sandwich‐like structure suffer from poor reproducibility, such as low effective ternary device yields and a wide threshold voltage distribution, and improvements through organic material renovation are rather limited. In contrast, engineering of the electrode surfaces rather than molecule design has been demonstrated to boost the performance of organic electronics effectively. Herein, we introduce surface engineering into organic multilevel RRAMs to enhance their ternary memory performance. A new asymmetric conjugated molecule composed of phenothiazine and malononitrile with a side chain (PTZ‐PTZO‐CN) was fabricated in an indium tin oxide (ITO)/PTZ‐PTZO‐CN/Al sandwich‐like memory device. Modification of the ITO substrate with a phosphonic acid (PA) prior to device fabrication increased the ternary device yield (the ratio of effective ternary device) and narrowed the threshold voltage distribution. The crystallinity analysis revealed that PTZ‐PTZO‐CN grown on untreated ITO crystallized into two phases. After the surface engineering of ITO, this crystalline ambiguity was eliminated and a sole crystal phase was obtained that was the same as in the powder state. The unified crystal structure and improved grain mosaicity resulted in a lower threshold voltage and, therefore, a higher ternary device yield. Our result demonstrated that PA modification also improved the memory performance of an asymmetric conjugated molecule with a side chain.     

卡马西平在nano-TiO2/[BnMIM] PF6修饰碳糊电极上的电催化氧化及电分析方法

运用循环伏安法(CV)、计时电流法(CA)、计时库仑法(CC)、方波伏安法(SWV)研究了卡马西平(CBZ)在纳米二氧化钛(nano-TiO2)与离子液体1-苄基-3-甲基咪唑六氟磷酸盐([BnMIM]PF6)复合修饰碳糊电极(nano-TiO2-[BnMIM] PF6/CPE )上的电化学行为、电化学动力学性质及电分...