低损宽频高双折射太赫兹光子带隙光纤

设计了一种低损耗、宽频段、高双折射太赫兹光子带隙光纤,呈三角晶格排列的亚波长空气孔包层实现了带隙的局域作用.利用全矢量有限元法对光纤的双折射及损耗特性进行了理论分析.结果表明,在大约0.3 THz的宽频范围内,类矩形纤芯太赫兹光子带隙光纤的损耗小于0.009 cm^-1,相双折射在10^-3数量级,群双折射可达10^-2数量级. 关键词： 太赫兹 太赫兹波导 光子晶体光纤 双折射     

Improved high birefringence photonic crystal fibres with dispersion flattened and single mode operation

A kind of improved high birefringence photonic crystal fibre (PCF) is proposed in this paper. The characteristics of birefringence, dispersion and leakage loss are studied by the multipole method. Numerical results show that the improved PCF possesses the properties of a flat dispersion and single mode operation. Moreover, with the operating wavelength λ = 1.55μm, the modal birefringence increases greatly in comparison with that of the original PCF, and the leakage loss is about 10⁴ times smaller than that of the original PCF because the modification gives rise to the strong confinement of guided modes. It is expected that the improved PCF can be used as high birefringence and dispersion flattened fibres.     

八边形高双折射双零色散点光子晶体光纤特性分析

针对光纤通信和传感系统中高双折射、多零色散点的应用需求, 设计了一种新型结构的光子晶体光纤.该结构包层为圆形空气孔按照八边形形状排列而成, 并在内包层对称位置中加入两个椭圆空气孔以获得高双折射特性. 通过有限元数值分析方法对光纤特性进行分析,仿真结果表明,该结构光子晶体光纤在波长0.8—2 μm 范围内双折射可达10^-3量级,满足高双折射的应用需求,并且满足两个零色散点的应用需求. 同时光纤的非线性系数达10^-2·m^-1·W^-1量级,可应用于对非线性要求较高的场合.     

Designing of a polarization beam splitter for the wavelength of 1310 nm on dual-core photonic crystal fiber with high birefringence and double-zero dispersion

We have proposed a novel kind of photonic crystal fiber which contains two asymmetric cores. The bireti＇ingence and the dispersion are numerically analyzed based on finite element method when the size of the air holes and the pitch of two adjacent air holes are changed. It is shown that the proposed photonic crystal fiber has high birefringence up to the order of 10-2 and double-zero dispersion points are at the wavelengths of 1310 nm and 800 rim, simultaneously. At the same time, the normalized power and the extinction ratios of the proposed photonic crystal fiber have been simulated. It is demonstrated that, at the wavelength of 1310 rim, the x-polarized mode and the y-polarized mode are separated when the propagation distance is 2.481 ram.     

高双折射纳米结构光子晶体光纤特性研究

设计了一种高双折射高非线性纳米结构光子晶体光纤,利用电磁场散射的多极理论研究了这种光纤的双折射、基模模场、色散以及非线性特性.数值研究发现,加大纤芯及包层空气孔的非对称程度,可使双折射变大,其双折射最大值可达1.918×10-2.通过调节孔节距大小,可将双折射最大值调至所需波长处,孔节距为400nm的纳米光子晶体光纤在800nm波长处非线性系数高达0.2m-1.W-1,同时在750—1000nm的波段有较大的双折射值,高双折射和高非线性在纳米结构光子晶体光纤中实现了完美的结合.对新型纳米光子器件的研制和集成光学的发展具有重要意义.     

新型高双折射及色散平坦光子晶体光纤研究

用平面波展开法对光子晶体光纤中电磁场的Maxwell方程组进行了求解。将光纤截面作为超元胞衍生出一个无边界的二维周期性系统，光纤纤芯等效为光子晶体中的缺陷，借助平面波法对其性质进行研究，模拟了半导体中的超格子。运用上述超格子模型，对与纤芯同列孔半径可变的高双折射及与包层中纤芯距离最近的孔半径可变的色散平坦光子晶体光纤的光学性质进行了研究，发现与纤芯同列的孔半径变化时，其双折射比传统光纤更强，而当包层中距离纤芯最近的孔半径取特定值时，可得到近零色散平坦光纤并在大范围内获得反常色散。与传统光纤和普通光子晶体光纤相比，这种新型的色散平坦光纤在密集波分复用（DWDM）光通信系统中具有更高的应用价值。     

Research on terahertz photonic crystal fiber characteristics with high birefringence

A new high birefringence photonic crystal fiber is proposed within the terahertz frequency region. It has two types of claddings, the inner is composed of six ellipse air holes arranged in a honeycomb array and the outer surrounded by circle holes. By using the full vector finite element method with anisotropic perfectly matched layers absorption boundary condition, the birefringence, chromatic dispersion and confinement loss of the fundamental mode are evaluated. The results show that the birefringence can achieve 10⁻³ when the wavelength increases from 600 μm to 900 μm. This structure will provide some reference value for the designing of high birefringence terahertz photonic crystal fiber.     

空气孔正方形排列的低损耗高双折射光子晶体光纤的数值模拟

提出了一种正方形排列渐增空气孔高双折射光子晶体光纤，并利用多极方法对光纤基模的模场分布、色散、双折射以及损耗特性进行了数值模拟.模拟结果表明利用这种结构可以在包层空气孔层数较少的情况下实现极低的限制损耗，通过调节内层空气孔的分布可以有效地控制光纤的双折射和色散特性.本结果对高双折射光子晶体光纤的制备具有一定的指导意义. 关键词： 光子晶体光纤 双折射 限制损耗 多极方法     

Temperature dependence of birefringence in olarization-maintaining photonic crystal fibres

In this paper,the temperature dependence of birefringence in polarization maintaining photonic crystal fibres(PMPCFs) is investigated theoretically and experimentally.Utilizing the structural parameters of the PM-PCF samples in the experiment,two effects leading to the birefringence variation under different temperatures are analysed,which are the thermal expansion of silica material and the refractive index variation due to the temperature variation.The actual birefringence variation of the PM-PCF is the combination of the two effects,which is in the order of 10-9 K-1 for both fibre samples.Calculation results also show that the influence of refractive index variation is the dominant contribution,which determines the tendency of the fibre birefringence variation with varying temperature.Then,the birefringence beat lengths of the two fibre samples are measured under the temperature,which varies from -40℃ to 80℃.A traditional PANDA-type polarization maintaining fibre(PMF) is also measured in the same way for comparison.The experimental results indicate that the birefringence variation of the PM-PCF due to temperature variation is far smaller than that of the traditional PMF,which agrees with the theoretical analysis.The ultra-low temperature dependence of the birefringence in the PM-PCF has great potential applications in temperature-insensitive fibre interferometers,fibre sensors,and fibre gyroscopes.     

Modal characteristics of few-mode silica-based photonic crystal fibres

The modal characteristics of silica-based photonic crystal fibres (PCF) are examined through a scalar modal analysis combined with an effective V-parameter model using a finite-difference method. Cut off frequencies of the lowest-order modes and the normalised dispersion curves are given and are found to be quasi-independent of the hole-size-to-pitch ratio. A simple and accurate empirical relation for the cutoff wavelength is given for the first higher-order mode for fibres with hole-size-to-pitch ratio below 0.7. These results should be very useful in designing PCF's for various applications.     

Widely tunable dual-pump parametric amplifiers with photonic crystal fibres

This paper theoretically studies the double-pumped fibre-optical parametric amplifiers (FOPAs) in photonic crystal fibres. Two distinct working regimes of FOPAs are researched, which depend on the dispersion at the central wavelength of the two pumps. Extremely broad tuning range can be obtained when the central pump wavelength is in the normal dispersion regime and is insensitive to the wavelength separation between the two pumps, while the tuning range is narrow in the anomalous dispersion regime and can be significantly enhanced by increasing the wavelength separation. Impacts of higher-order dispersions and temporal walk-off on the gain spectra are also discussed.     

Widely tunable dual-pump parametric amplifiers with photonic crystal fibres

This paper theoretically studies the double-pumped fibre-optical parametric amplifiers （FOPAs） in photonic crystal fibres. Two distinct working regimes of FOPAs are researched, which depend on the dispersion at the central wavelength of the two pumps. Extremely broad tuning range can be obtained when the central pump wavelength is in the normal dispersion regime and is insensitive to the wavelength separation between the two pumps, while the tuning range is narrow in the anomalous dispersion regime and can be significantly enhanced by increasing the wavelength separation. Impacts of higher-order dispersions and temporal walk-off on the gain spectra are also discussed.     

菱形纤芯光子晶体光纤色散与双折射特性分析

针对光子晶体光纤多零色散点、高双折射的应用要求, 设计了一种新型结构的光子晶体光纤, 其纤芯由位于菱形四个角上的圆形空气孔组成. 通过有限元数值分析方法对该种结构光子晶体光纤的色散特性和双折射特性进行数值仿真, 得到色散与波长、色散与纤芯圆孔尺寸、双折射与波长、双折射与纤芯圆孔尺寸的关系. 研究结果表明:在满足光纤传输功率要求的条件下, 光纤的双折射在d₁<0.8 μupm 时的性能较好. 同时, 该种结构的光子晶体光纤在芯区直径满足d₁=0.4 μupm或 d₁=0.6 μupm时会出现两个零色散点, 这对进一步研制具有多零色散点的光子晶体光纤具有重要的意义.     

Equilateral pentagon polarization maintaining photonic crystal fibre with low nonlinearity

A new pentagon polarization maintaining photonic crystal fibre with low nonlinearity is introduced. The full vector finite element method was used to investigate the distribution and the effective area of modal field, the nonlinear properties, the effective indices of two orthogonal polarization modes and the birefringence of the new PM-PCF effectively. It is found that the birefringence of the new polarization maintaining photonic crystal fibre can easily achieve the order of 10^-4, and it can obtain higher birefringence, larger effectively mode-field area and lower nonlinearity than traditional hexagonal polarization maintaining photonic crystal fibre with the same hole pitch, same hole diameter, and same ring number. It is important for sensing and communication applications, especially has potential application for fibre optical gyroscope.     

菱形纤芯光子晶体光纤色散与双折射特性分析

针对光子晶体光纤多零色散点、高双折射的应用要求, 设计了一种新型结构的光子晶体光纤, 其纤芯由位于菱形四个角上的圆形空气孔组成. 通过有限元数值分析方法对该种结构光子晶体光纤的色散特性和双折射特性进行数值仿真, 得到色散与波长、色散与纤芯圆孔尺寸、双折射与波长、双折射与纤芯圆孔尺寸的关系. 研究结果表明:在满足光纤传输功率要求的条件下, 光纤的双折射在d₁<0.8 μupm 时的性能较好. 同时, 该种结构的光子晶体光纤在芯区直径满足d₁=0.4 μupm或 d     

基于石墨烯的可调谐太赫兹光子晶体结构

本文将石墨烯引入到常规光子晶体中构建一种新型光子晶体, 首次从理论上严格导出了决定其能带结构的色散关系, 由于色散关系中石墨烯电导率的存在导致了它具有与常规光子晶体有所不同的特殊光学性质, 我们发现, 随着费米能增大, 低频段能带迅速向高频移动, 而高频段能带移动缓慢, 导致了常规光子晶体没有的能带压缩现象的发生, 究其原因在于石墨烯在低频段电导率迅速变化, 而高频段电导率变化缓慢, 导致能带向高频压缩, 使得光波原先允许频率变成禁止传播, 而禁止频率变成允许传播.     

光子晶体光纤的导波模式与色散特性

利用有效折射率方法基于标量近似理论对光子晶体光纤的传播模式和色散特性进行了数值模 拟，发现通过调节光纤包层的空气填充率或包层空气穴节距及其有效芯径可以在很宽的波长 范围实现单模传播，可以设计零色散波长小于1.27μm的光子晶体光纤和在较宽的波段接近 于零色散的色散平坦光纤，以及具有较大的正常色散值的色散补偿光纤. 关键词： 光子晶体光纤 有效折射率 标量近似 导波模式     

低损耗宽带近零色散高非线性光子晶体光纤设计

提出了一种兼具低损耗、宽带近零色散和高非线性的光子晶体光纤结构,该结构光纤包层空气孔直径从纤芯向外层方向渐进增加;应用多极法,通过改变包层空气孔间距Λ、各层空气孔直径和空气孔层数N_r,对光子晶体光纤色散、损耗和非线性特性进行分析,获得了各特性随包层结构参数变化的规律,并最终设计出最佳结构参数。计算结果表明,该结构光纤存在3个零色散点,在1.25～1.55 μm较宽的波长范围内,色散值波动小于0.27 ps·nm⁻¹·km⁻¹,色散斜率小于0.008 ps·km⁻¹·nm⁻²,1.55 μm波长处损耗为0.021 dB/km,在常用的飞秒激光泵浦波长0.8,1.06,1.55 μm处非线性系数分别达到78.6,60.4,38.2 W⁻¹·km⁻¹。     

一种新型高双折射光子晶体光纤

提出了一种新的高双折射光子晶体光纤结构.应用全矢量频域有限差分方法所做的数值分析表明：该结构光纤基模的两个正交偏振态不再简并，其模式呈现很强的线偏振特性,并且模式双折射与结构参数设置有密切关系.通过选择合适的结构参数，可以使之达到10^-2量级，比传统的D型和熊猫型保偏光纤高出2个数量级.合理设计光纤包层的几何结构，可以取得理想的色散效果.这种结构的光子晶体光纤可用于制作具有适当色散特性或偏振特性的保偏光纤及相关光纤器件. 关键词： 光子晶体光纤 模式双折射 偏振特性 频域有限差分法