Comparative study of structural and magnetic properties of nano-crystalline Li0.5Fe2.5O4 prepared by various methods

Lithium ferrite has been considered as one of the highly strategic magnetic material. Nano-crystalline Li_0.5Fe_2.5O₄ was prepared by four different techniques and characterized by X-ray diffraction, vibrating sample magnetometer (VSM), transmission electron microscope (TEM) and Fourier transform infrareds (FTIR). The effect of annealing temperature (700, 900 and 1050 °C) on microstructure has been correlated to the magnetic properties. From X-ray diffraction patterns, it is confirmed that the pure phase of lithium ferrite began to form at 900 °C annealing. The particle size of as-prepared lithium ferrite was observed around 40, 31, 22 and 93 nm prepared by flash combustion, sol-gel, citrate precursor and standard ceramic technique, respectively. Lithium ferrite prepared by citrate precursor method shows a maximum saturation magnetization 67.6 emu/g at 5 KOe.     

Synthesis and characterization of lithium ferrite by oxalate precursor route

Nanocrystalline lithium ferrite (LiFe₅O₈) powders have been synthesized by oxalate precursor route. The effects of Fe³⁺/Li⁺ mole ratio, and annealing temperature on the formation, crystalline size, morphology and magnetic properties were systematically studied. The Fe³⁺/Li⁺ mole ratio was controlled from 5 to 3.33 while the annealing temperature was controlled from 600 to 1100 °C. The resultant powders were investigated by differential thermal analyzer (DTA), X-ray diffractometer (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). DTA results showed that LiFe₅O₈ phase started to form at around 520 °C. XRD indicated that LiFe₅O₈ phase always contained α-Fe₂O₃ impurity and the hematite phase formation increased by increasing the annealing temperature ?850 °C for different Fe³⁺/Li⁺ mole ratios 5, 4.55 and 3.85. Moreover, lithium ferrite phase was formed with high conversion percentage at critical annealing temperature 750–800 °C. Single well crystalline LiFe₅O₈ phase was obtained at Fe³⁺/Li⁺ mole ratio 3.33 and annealing temperatures from 800 to 1000 °C. Maximum saturation magnetization (68.7 emu/g) was achieved for the formed lithium ferrite phase at Fe³⁺/Li⁺ mole ratio 3.33 and annealing temperature 1000 °C.     

Structural and electrochemical properties of Nd-doped LiFePO4/C prepared without using inert gas

To further improve the electrochemical performance of LiFePO₄/C, Nd doping has been adopted for cathode material of the lithium ion batteries. The Nd-doped LiFePO₄/C cathode was synthesized by a novel solid-state reaction method at 750 °C without using inert gas. The Li_0.99Nd_0.01FePO₄/C composite has been systematically characterized by X-ray diffraction, EDS, SEM, TEM, charge/discharge test, electrochemical impedance spectroscopy and cyclic stability. The results indicate that the prepared sample has olivine structure and the Nd³⁺ and carbon modification do not affect the structure of the sample but improve its kinetics in terms of discharge capacity and rate capability. The Li_0.99Nd_0.01FePO₄/C powder exhibited a specific initial discharge capacity of about 161 mAh g^− 1 at 0.1 C rate, as compared to 143 mAh g^− 1 of LiFePO₄/C. At a high rate of 2 C, the discharge capacity of Li_0.99Nd_0.01FePO₄/C still attained to 115 mAh g^− 1 at the end of 20 cycles. EIS results indicate that the charge transfer resistance of LiFePO₄/C decreases greatly after Nd doping.     

Molten salt synthesis of Li1 + x (Ni0.5Mn0.5)1 − xO2 as cathode material for Li-ion batteries

Li_1 + x(Ni_0.5Mn_0.5)_1 − xO₂ cathode material for Li-ion batteries has been prepared by a molten salt method using Li₂CO₃ salt. The influences of synthetic temperature and time have been intensively investigated. It is easy to obtain materials with a hexagonal α-NaFeO₂ structure except broad peaks between 20° and 25°. Nickel in Li_1 + x(Ni_0.5Mn_0.5)_1 − xO₂ is oxidized to a trivalent state while manganese maintained a tetravalent state. It is found that the discharge capacities of all samples increase with cycling. The sample prepared at 850 °C for 5 h has a discharge capacity of 130 mAh g^− 1 between 2.5 and 4.5 V versus V_Li+/Li at a specific current of 0.13 mA cm^− 2 after 50 cycles at 25 °C.     

Electrochemical properties of electrosynthesized TiO2 thin films

Titanium dioxide (TiO₂) thin films prepared by cathodic electrodeposition on indium-tin-oxide coated glass substrates from simple aqueous peroxo-titanium complex solutions have been studied as a function of sintering temperature (25-500 °C). The films crystallized in to anatase phase at relatively low temperature (300 °C). Electrochemical properties of amorphous and anatase films were investigated by cyclic voltammogram (CV) in lithium ion containing organic electrolyte. All the films were found to show reversible electrochemical properties upon Li⁺ ion intercalation. The effects of sintering temperature on the crystallinity and consequently on the electrochemical properties of TiO₂ has been discussed.     

Synthesis and characterization of thermoluminescent Li2B4O7 nanophosphor

Lithium borate (Li₂B₄O₇) is a low Z_eff, tissue equivalent material that is commonly used for medical dosimetry using the thermoluminescence (TL) technique. Nanocrystals of lithium borate were synthesized by the combustion method for the first time in the laboratory. TL characteristics of the synthesized material were studied and compared with those of commercially available microcrystalline Li₂B₄O₇. The optimum pre-irradiation annealing condition was found to be 300 °C for 10 min and that of post-irradiation annealing was 300 °C for 30 min. The synthesized Li₂B₄O₇ nanophosphor has very poor sensitivity for low doses of gamma up to 10¹ Gy whereas from 10¹ to 4.5×10² Gy this phosphor exhibits a linear response and then from 4.5×10² to 10³ Gy it shows supralinearity. Thermoluminescence properties of Li₂B₄O₇ nanophosphor doped with Cu has also been investigated in this paper. It shows low fading and a linear response over a wide range of gamma radiation from 1×10² to 5×10³ Gy. Therefore the synthesized lithium borate nanophosphor doped with Cu may be used for high dose measurements of gamma radiations.     

Characteristics of spherical-shaped Li4Ti5O12 anode powders prepared by spray pyrolysis

Spherical-shaped Li₄Ti₅O₁₂ anode powders with a mean size of 1.5 μm were prepared by spray pyrolysis. The precursor powders obtained by spray pyrolysis had no peaks of crystal structure of Li₄Ti₅O₁₂. The powders post-treated at temperatures of 800 and 900 °C had the single phase of spinel Li₄Ti₅O₁₂. The powders post-treated at a temperature of 1000 °C had main peaks of the Li₄Ti₅O₁₂ phase and small impurity peaks of Li₂Ti₃O₇. The spherical shape of the precursor powders was maintained after post-treatment at temperatures below 800 °C. The Brunauer-Emmett-Teller (BET) surface areas of the Li₄Ti₅O₁₂ anode powders post-treated at temperatures of 700, 800 and 900 °C were 4.9, 1.6 and 1.5 m²/g, respectively. The initial discharge capacities of Li₄Ti₅O₁₂ powders were changed from 108 to 175 mAh/g when the post-treatment temperatures were changed from 700 to 1000 °C. The maximum initial discharge capacity of the Li₄Ti₅O₁₂ powders was obtained at a post-treatment temperature of 800 °C, which had good cycle properties below current densities of 0.7 C.     

Electrostatic spray deposition of spinel Li4Ti5O12 thin films for rechargeable lithium batteries

Spinel Li₄Ti₅O₁₂ thin films are important for the fabrication of rechargeable lithium microbatteries. Porous thin films of Li₄Ti₅O₁₂ were prepared by electrostatic spray deposition (ESD) technique with lithium acetate and titanium butoxide as the precursors. The structures of these films were analyzed by scanning electron microscopy and X-ray diffraction. Coin-type cells with a liquid electrolyte were made with the Li₄Ti₅O₁₂ films against metallic lithium. Their electrochemical performance was investigated by means of galvanostatic cell cycling, cyclic voltammetry and Ac impedance spectroscopy. It was found that pure spinel phase of Li₄Ti₅O₁₂ was obtained. After annealing at the optimal temperature of 700 °C, the films can deliver a reversible specific capacity of about 150 mAh/g with excellent capacity retention after 70 cycles. Their electrochemical characteristics were quite comparable with those of the Li₄Ti₅O₁₂ laminate electrodes containing carbon black additive.     

A novel method to synthesize LiVPO4F/C composite materials and its electrochemical Li-intercalation performances

Triclinic LiVPO₄F/C composite materials were prepared from a sucrose-containing precursor by one-step heat treatment. As-prepared composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrochemical measurements. XRD studies showed that Li₃PO₄ impurity phase appeared in the sample synthesized at 600 °C and pure LiVPO₄F samples could be obtained when the sintered temperature was higher than 650 °C. The sample synthesized at 650 °C presents the highest initial discharge capacity of 132 mAh g⁻¹ at 0.2 C rate, and exhibited better cycling stability (124 mAh g⁻¹ at 50th cycle at 0.2 C rate) and better rate capability (100 mAh g⁻¹ at 50th cycle under 1 C rate) in the voltage range 3.0-4.4 V.     

Synthesis and electrochemical properties of nanostructured Li2FeSiO4/C cathode material for Li-ion batteries

Nanostructured Li₂FeSiO₄/C was synthesized by high-energy ball-milling and the amorphous citrate-assisted techniques. Similar redox behaviour is observed for samples prepared by the amorphous citrate-assisted route followed by a 4 h heat treatment: 0.3 V polarization and more sloping behaviour was observed when cycling between 2.0 V and 3.7 V at 60 °C; lower capacity fade is also observed compared to Li₂FeSiO₄/C prepared by the solid-state reaction technique. A discharge capacity of 102 mA h g^− 1 is obtained for samples prepared by the high-energy ball-milling method, while capacities decrease from 95 to 77 mA h g^− 1 using the amorphous citrate method for heat-treatment times increasing successively from 4 h to 18 h.     

Preparation and ozone-surface modification of activated carbon. Thermal stability of oxygen surface groups

The control of the surface chemistry of activated carbon by ozone and heat treatment is investigated. Using cherry stones, activated carbons were prepared by carbonization at 900 °C and activation in CO₂ or steam at 850 °C. The obtained products were ozone-treated at room temperature. After their thermogravimetric analysis, the samples were heat-treated to 300, 500, 700 or 900 °C. The textural characterization was carried out by N₂ adsorption at 77 K, mercury porosimetry, and density measurements. The surface analysis was performed by the Bohem method and pH of the point of zero charge (pH_pzc). It has been found that the treatment of activated carbon with ozone combined with heat treatment enables one to control the acidic-basic character and strength of the carbon surface. Whereas the treatment with ozone yields acidic carbons, carbon dioxide and steam activations of the carbonized product and the heat treatment of the ozone-treated products result in basic carbons; the strength of a base which increases with the increasing heat treatment temperature. pH_pzc ranges between 3.6 and 10.3.     

Synthesis and characterization of thermoluminescent glass-ceramics Li2O-Al2O3-SiO2:CeO2

Vitroceramic powders of Li₂O-Al₂O₃-SiO₂ systems (LAS), doped with 1% (LAS:1Ce) and 10% (LAS:10Ce) molar of cerianite (CeO₂) were synthesized by means of the gelification technique of metal formates of aluminum and lithium, in the presence of tetraethoxy silane and CeO₂. The gels obtained were dried (120 °C, 2.5 h), calcined (480 °C, 5 h) and sinterized (1250 °C, 30 min). The sinterized samples were characterized by X-ray difraction (XRD), scanning electron microscopy (SEM) and microchemical analysis (EDS). There is evidence for a mixture of two phases of 64% β-spodumene (Li₂O-Al₂O₃-4SiO₂) and 36% β-eucryptite (Li₂O-Al₂O₃-2SiO₂). The LAS:1Ce system was enriched in aluminum, the LAS:10Ce system showed areas of heterogeneous composition; some regions with a shortage of CeO₂, while others zones with cerium cumulus. From the microscopy images it was found that CeO₂ acts as a densificant agent in LAS system, favoring the sintering in the host. The chemical route and the sintering processes utilized allow the production of samples exhibiting an acceptable linear correlation between total thermoluminescent emission intensity and the irradiation dose when the CeO₂ concentration is low (less than 1%), opening the possibility of using this kind of glass-ceramic in dosimetry.     

Li0.5Fe2.5−xMnxO4 ferrite sintered from microwave-induced combustion

Li_0.5Fe_2.5−xMn_xO₄ (0≦x≦1.0) powders with small and uniformly sized particles were successfully synthesized by microwave-induced combustion, using lithium nitrate, ferric nitrate, manganese nitrate and carbohydrazide as the starting materials. The process takes only a few minutes to obtain as-received Mn-substituted lithium ferrite powders. The resultant powders annealed at 650 ^°C for 2 h and were investigated by thermogravimeter/differential thermal analyzer (TG/DTA), X-ray diffractometer (XRD), transmission electron microscopy (TEM), vibrating sample magnetometer (VSM), and thermomagnetic analysis (TMA). The results revealed that the Mn content were strongly influenced the magnetic properties and Curie temperature of Mn-substituted lithium ferrite powder. As for sintered Li_0.5Fe_2.5−xMn_xO₄ specimens, substituting an appropriate amount of Mn for Fe in the Li_0.5Fe_2.5−xMn_xO₄ specimens markedly improved the complex permeability and loss tangent.     

Thermoluminescent and stuctural properties of BaAl2O4:Eu,Nd,Gdphosphors prepared by combustion method

BaAl₂O₄:Eu²⁺,Nd³⁺,Gd³⁺ phosphors were prepared by a combustion method at different initiating temperatures (400–1200 °C), using urea as a comburent. The powders were annealed at different temperatures in the range of 400–1100 °C for 3 h. X-ray diffraction data show that the crystallinity of the BaAl₂O₄ structure greatly improved with increasing annealing temperature. Blue-green photoluminescence, with persistent/long afterglow, was observed at 498 nm. This emission was attributed to the 4f⁶5d¹–4f⁷ transitions of Eu²⁺ ions. The phosphorescence decay curves were obtained by irradiating the samples with a 365 nm UV light. The glow curves of the as-prepared and the annealed samples were investigated in this study. The thermoluminescent (TL) glow peaks of the samples prepared at 600 °C and 1200 °C were both stable at ∼72 °C suggesting that the traps responsible for the bands were fixed at this position irrespective of annealing temperature. These bands are at a similar position, which suggests that the traps responsible for these bands are similar. The rate of decay of the sample annealed at 600 °C was faster than that of the sample prepared at 1200 °C.     

Magnetic properties in Fe-doped NiO synthesized by co-precipitation

The magnetic properties of 1.5 at% Fe-doped NiO bulk samples were investigated. The samples were prepared by sintering the corresponding precursor in air at temperatures between 400 and 800 °C for 6 h. The synthesis was by a chemical co-precipitation and post-thermal decomposition method. In order to allow a comparison, a NiO/0.76 at% NiFe₂O₄ mixture was also prepared. The X-ray diffraction pattern shows that the samples that were sintered at 400 and 600 °C remain single phase. As the sintering temperature increased to 800 °C, however, the sample becomes a mixture of NiO and NiFe₂O₄ ferrite phases. The samples were investigated by measuring their magnetization as a function of magnetic field. The samples sintered between 400 and 800 °C and the one mixed directly with NiFe₂O₄ nanoparticles show a coercivity value of H_c≈200, 325, 350 and 110 Oe, respectively. The magnetic properties of the samples depend strongly on the sintering temperature. Simultaneously, the field-cooling hysteresis loop shift also observed after cooling the sample sintered at 600 °C to low temperature suggests the possibility of the existence of a ferromagnetic/antiferromagnetic exchange coupling.     

Mechanism and kinetics of lithium vapor capture in a high-temperature packed bed of kaolinite

This study investigated the characteristics of high-temperature lithium vapor-capturing reaction in a packed bed of calcined kaolin particles. The packed-bed sorption experiments were carried in the a temperature range of 700-900 °C. The high-temperature reaction between LiCl vapor and calcined kaolin sorbent generated lithium aluminum silicate (Li₂O·Al₂O₃·2SiO₂). An increase in kaolin bed temperature results in an increase in lithium-capturing rate, but it has no effect on the maximum lithium uptake. The resistance of LiCl vapor diffusion into the pores of calcined kaolin particles was negligible, and the chemical reaction at the kaolin surface controlled the overall sorption reaction rates by up to 60% of metakaolinite conversion. The order of the reaction between metakaolinite and LiCl vapor was determined as 1.94 and its activation energy was estimated as 7.95 kcal/mol according to the Arrhenius relationship.     

Effect of Li2O and CoO-doping of CuO/Fe2O3 system on its surface and catalytic properties

Physicochemical, surface and catalytic properties of pure and doped CuO/Fe₂O₃ system were investigated using X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX), nitrogen adsorption at −196 °C and CO-oxidation by O₂ at 80-220 °C using a static method. The dopants were Li₂O (2.5 mol%) and CoO (2.5 and 5 mol%). The results revealed that the increase in precalcination temperature from 400 to 600 °C and Li₂O-doping of CuO/Fe₂O₃ system enhanced CuFe₂O₄ formation. However, heating both pure and doped solids at 600 °C did not lead to complete conversion of reacting oxides into CuFe₂O₄. The promotion effect of Li₂O dopant was attributed to dissolution of some of dopant ions in the lattices of CuO and Fe₂O₃ with subsequent increase in the mobility of reacting cations. CoO-doping led also to the formation of mixed ferrite Co_xCu_1−xFe₂O₄. The doping process of the system investigated decreased to a large extent the crystallite size of unreacted portion of Fe₂O₃ in mixed solids calcined at 600 °C. This process led to a significant increase in the S_BET of the treated solids. Doping CuO/Fe₂O₃ system with either Li₂O or CoO, followed by calcination at 400 and 600 °C decreased its catalytic activity in CO-oxidation by O₂. However, the activation energy of the catalyzed reaction was not much affected by doping.     

Thermoluminescence of B2O3-Li2O glass system doped with MgO

Lithium borate (LiB) glasses in the system (100−x)B₂O₃-xLi₂O with x=20, 30, 40, 50, 60 and 70 mol% were prepared. The glasses were doped with different concentrations of the order of 10⁻¹, 10⁻², 10⁻³, 10⁻⁴ and 10⁻⁵ of MgO and their thermoluminescent (TL) response was investigated. The irradiations were performed using γ rays from a ⁶⁰Co source in the dose range from 0.1 to 25 kGy. The material displayed good sensitivity for γ-rays and intensity of TL signals is dependent on γ-ray dose and Li₂O content. For each dose level and investigated temperature range (50-350 °C), exactly single isolated glow peak appears in the temperature range of 165-205 °C depending on both Li₂O concentrations and time of exposure. The shape of the glow peak has altered significantly with increase in the gamma ray dose or Li₂O concentrations. The glass composition with x=50 mol% doped with 10⁻³ mol% of MgO presented the best TL response. The results of the present study indicated that the recorded single and isolated high temperature peak is a good candidate for TL dosimetric investigations. This indicates that 50 B₂O₃-50Li₂O-doped with 10⁻³ mol% of MgO is possibly used as materials for radiation dosimetry in the dose range of 0.1-20 kGy.     

Fuel additives and heat treatment effects on nanocrystalline zinc ferrite phase composition

Nanocrystalline ZnFe₂O₄ powder was prepared by the auto-combustion method using citric acid, acetic acid, carbamide and acrylic acid as fuel additives. Pure spinel zinc ferrite with the crystallite size of about 15 nm can be obtained by using acrylic acid as fuel additive. Samples prepared using other fuel additives contain ZnO impurities. In order to eliminate ZnO impurities, the sample prepared with citric acid as fuel additive was annealed at different temperatures up to 1000 °C in air and in argon. Annealed powders have pure ZnFe₂O₄ phase when annealing temperature is higher than 650 °C in air. Sample annealed at 650 °C in air is paramagnetic. However, annealed powders become a mixture of Fe₃O₄ and FeO after annealing at 1000 °C in argon atmosphere due to Zn volatility and the reduction reaction.