Utilization of Banana Peel as a Novel Substrate for Biosurfactant Production by Halobacteriaceae archaeon AS65

In this study, biosurfactant-producing bacteria was evaluated for biosurfactant production by using banana peel as a sole carbon source. From the 71 strains screened, Halobacteriaceae archaeon AS65 produced the highest biosurfactant activity. The highest biosurfactant production (5.30 g/l) was obtained when the cells were grown on a minimal salt medium containing 35 % (w/v) banana peel and 1 g/l commercial monosodium glutamate at 30 °C and 200 rpm after 54 h of cultivation. The biosurfactant obtained by extraction with ethyl acetate showed high surface tension reduction (25.5 mN/m), a small critical micelle concentration value (10 mg/l), thermal and pH stability with respect to surface tension reduction and emulsification activity, and a high level of salt tolerance. The biosurfactant obtained was confirmed as a lipopeptide by using a biochemical test FT-IR, NMR, and mass spectrometry. The crude biosurfactant showed a broad spectrum of antimicrobial activity and had the ability to emulsify oil, enhance PAHs solubility, and oil bioremediation.     

Bioremediation of Marine Sediments Impacted by Petroleum

The aim of this work was to optimize the bioremediation of crude oil-contaminated sand sediment through the biostimulation technique. The soil was obtained in the mid-tide zone of Guanabara Bay, Rio de Janeiro, Brazil and was artificially contaminated with crude oil at 14 g kg^?1. Bioremediation optimization was performed using an experimental design and statistical analysis of the following factors: supplementation with commercial biosurfactant Jeneil® IBR 425 and commercial mineral NPK fertilizer. The response variable used was the biodegradation of the heavy oil fraction, HOF. The analysis of the studied factors and their interactions was executed using contour plots, Pareto diagram and ANOVA table. Experimental design results indicated that the supplementation with fertilizer at 100:25:25 C/N/P ratio and biosurfactant at 2 g kg^?1 yielded biodegradation of HOF at about 30% during 30 days of process. Some experiments were carried out using the experimental design results, yielding 65% of biodegradation of HOF and 100% of n- alkanes between C15 and C30 during 60 process days. Intrinsic biodegradation test was carried out, yielding 85% of biodegradation of n-alkanes between C15 and C30 during 30 days of process.     

Evaluation and Functional Characterization of a Biosurfactant Produced by Lactobacillus plantarum CFR 2194

The study details the investigations on the ability of Lactobacillus plantarum CFR 2194, an isolate from kanjika, a rice-based ayurvedic fermented product, to produce biosurfactant. Surfactant production, as a function of fermentation time, indicates that the maximum production occurred at 72 h under stationary conditions. Isolation, partial purification, and characterization of the biosurfactant produced have been carried out, and Fourier transform infrared spectroscopy (FTIR) spectra demonstrated that biosurfactants were constituted by protein and polysaccharide fractions, i.e., possessed the structure typical of glycoprotein, which is affected by the medium composition and the phase of growth of the biosurfactant-synthesizing strain. Critical micelle concentration (cmc) of the biosurfactant was found to be 6 g l^?1. The emulsification index (EI), emulsification activity (EA), and emulsion stability (ES) values of the biosurfactant have confirmed its emulsification property. Aqueous fractions of the produced biosurfactant exhibited a significant antimicrobial activity against the food-borne pathogenic species: Escherichia coli ATCC 31705, E. coli MTCC 108, Salmonella typhi, Yersinia enterocolitica MTCC 859, and Staphylococcus aureus F 722. More importantly, the biosurfactant from L. plantarum showed antiadhesive property against above food-borne pathogens. The results thus indicate the potential for developing strategies to prevent microbial colonization of food contact surfaces and health-care prosthesis using these biosurfactants.     

Production and Properties of a Surface-Active Lipopeptide Produced by a New Marine Brevibacterium luteolum Strain

Microbial-derived surfactants are molecules of great interest due to their environmentally friendly nature and low toxicity; however, their production cost is not competitive when compared to synthetics. Marine microorganisms are exposed to extremes of pressure, temperature, and salinity; hence, they can produce stable compounds under such conditions that are useful for industrial applications. A screening program to select marine bacteria able to produce biosurfactant using low-cost substrates (mineral oil, sucrose, soybean oil, and glycerol) was conducted. The selected bacterial strain showed potential to synthesize biosurfactants using mineral oil as carbon source and was identified as Brevibacterium luteolum. The surface-active compound reduced the surface tension of water to 27 mN m^?1 and the interfacial tension (water/hexadecane) to 0.84 mN m^?1 and showed a critical micelle concentration of 40 mg L^?1. The biosurfactant was stable over a range of temperature, pH, and salt concentration and the emulsification index (E₂₄) with different hydrocarbons ranging from 60 to 79 %. Structural characterization revealed that the biosurfactant has a lipopeptide nature. Sand washing removed 83 % of crude oil demonstrating the potential of the biosurfactants (BS) for bioremediation purposes. The new marine B. luteolum strain showed potential to produce high surface-active and stable molecule using a low-cost substrate.     

Exopolysaccharides and Antimicrobial Biosurfactants Produced by Paenibacillus macerans TKU029

Paenibacillus macerans TKU029 can produce exopolysaccharides (EPSs; 3.46 g/L) and a biosurfactant (1.78 g/L) in a medium with 2 % (w/v) squid pen powder as the sole carbon/nitrogen source. The biosurfactant can reduce the surface tension of water from 72.30 to 35.34 mN/m at a concentration of 2.76 g/L and reach an emulsification index of 56 % after a 24-h reaction with machine oil. This biosurfactant is stable at 121 °C for 20 min, over a pH range from 3 to 11, and in <5 % salt solutions. It also shows significant antimicrobial activity, which remains active after treatment at 121 °C and at pH values from 4 to 10, against Escherichia coli BCRC13086, Staphylococcus aureus BCRC10780, Fusarium oxysporum BCRC32121 and Aspergillus fumigatus BCRC30099. Furthermore, human skin shows from 37.3 to 44.3 % hydration after being treated with TKU029 EPSs for 180 min. These results imply that EPSs and the biosurfactant from this strain have potential in cosmetics, for removal of oil contamination, and as antimicrobial agents.     

Production of a Bioemulsifier with Potential Application in the Food Industry

Biosurfactants are of considerable interest due to their biodegradability, low degree of toxicity, and diverse applications. However, the high production costs involved in the acquisition of biosurfactants underscore the need for optimization of the production process to enable viable application on an industrial scale. The aims of the present study were to select a species of Candida that produces a biosurfactant with the greatest emulsifying potential and to investigate the influence of components of the production medium and cultivation conditions. Candida utilis achieved the lowest surface tension (35.53 mN/m), best emulsification index (73 %), and highest yield (12.52 g/l) in a medium containing waste canola frying oil as the carbon source and ammonium nitrate as the nitrogen source. The best combination of medium components and cultivation conditions was 6 % (w/v) glucose, 6 % (w/v) waste canola frying oil, 0.2 % (w/v) ammonium nitrate, 0.3 % (w/v) yeast extract, 150 rpm, 1 % inoculum (w/v), and 88 h of fermentation. The greatest biosurfactant production and the lowest surface tension were achieved in the first 24 h of production, and the maximum biomass production was recorded at 72 h. The biosurfactant produced from C. utilis under the conditions investigated in the present study has a potential to be a bioemulsifier for application in the food industry.     

Production of Microbial Surfactants from Oily Sludge-Contaminated Soil by Bacillus subtilis DSVP23

The indigenous microbial community utilizing aliphatic, aromatic, and polar components from the oily sludge as sole source of carbon and energy was selected from the soil samples of Ankleshwar, India for biosurfactant production. Evaluation of biosurfactant production was done using screening assays such as surface tension reduction, hemolytic activity, emulsification activity, drop-collapse assay, and cell surface hydrophobicity studies. Maximum biosurfactant (6.9?g/l) production was achieved after 5?days of growth from Bacillus subtilis DSVP23 which was identified by 16S RNA technique (NCBI GenBank accession no. EU679368). Composition of biosurfactant showed it to be lipopeptide in nature with 15.2% protein content and 18.0% lipid content. Functional group analysis was also done by using Fourier transform infrared spectroscopy which showed it to be a protein-bound lipid thereby imparting them special properties. Analysis by matrix-assisted laser desorption/ionization time-of-flight mass spectrometric and nuclear magnetic resonance revealed that the major constituents of lipopeptide are leucine and isoleucine. Gas chromatographic analysis data indicated that oily sludge components of chain length C₁₂?CC₃₀ and aromatic hydrocarbons were degraded effectively by B. subtilis DSVP23 after 5?days of incubation. These results collectively points toward the importance of B. subtilis DSVP23 as a potential candidate for bioremediation studies.     

Evaluation of Cashew Apple Juice for Surfactin Production by Bacillus subtilis LAMI008

Bacillus subtilis LAMI008 strain isolated from the tank of Chlorination at the Wastewater Treatment Plant on Campus do Pici in Federal University of Ceará, Brazil has been screened for surfactin production in mineral medium containing clarified cashew apple juice (MM-CAJC). Results were compared with the ones obtained using mineral medium with glucose PA as carbon source. The influence on growth and surfactin production of culture medium supplementation with yeast extract was also studied. The substrate concentration analysis indicated that B. subtilis LAMI008 was able to degrade all carbon sources studied and produce biosurfactant. The highest reduction in surface tension was achieved with the fermentation of MM-CAJC, supplemented with yeast extract, which decreased from 58.95?±?0.10 to 38.10?±?0.81 dyn cm^?1. The biosurfactant produced was capable of emulsifying kerosene, achieving an emulsification index of 65%. Surfactin concentration of 3.5 mg L^?1 was obtained when MM-CAJC, supplemented with yeast extract, was used, thus indicating that it is feasible to produce surfactin from clarified cashew apple juice, a renewable and low-cost carbon source.     

Synergistic Effect of Sarocladium sp. and Cryptococcus sp. Co-Culture on Crude Oil Biodegradation and Biosurfactant Production

This study was conducted to evaluate the co-culture ability of two yeast (Sarocladium sp. and Cryptococcus sp.) isolates as compared to their individual cultures in surfactant production and oil degradation. The results showed that individual culture of each strain was capable of producing surfactant, degrading oil, and pyrene; also, a synergistic effect was observed when a co-culture was applied. Oil removal and biomass production were 28 and 35% higher in the co-culture than in individual cultures, respectively. To investigate the synergistic effects of mix culture on oil degradation, the surface tension, emulsification activity (EA), and cell surface hydrophobicity of individual and co-culture were studied. A comparison between the produced biosurfactant and chemical surfactants showed that individual culture of each yeast strain could reduce the surface tension like SDS and about 10% better than Tween 80. The results showed that the microbial consortium could reduce the surface tension more, by 10 and 20%, than SDS and Tween 80, respectively. Both individual cultures of Sarocladium sp. and Cryptococcus sp. showed good emulsification activity (0.329 and 0.412, respectively) when compared with a non-inoculated medium. Emulsification activity measurement for the two yeast mix cultures showed an excellent 33 and 67% increase as compared to the individual culture of Sarocladium sp. and Cryptococcus sp., respectively. The cell surface hydrophobicity of Sarocladium sp. and Cryptococcus sp. increased (38 and 85%) when the cells were treated with pyrene as a hydrophobic substrate for four generations. Finally, a 40% increase for pyrene degradation was measured in a co-culture of the two yeast mix culture. According to the results of the present study, the co-culture system exhibited better performance and this study will enhance the understanding of the synergistic effects of yeast co-culture on oil degradation.

     

First Report of a Lipopeptide Biosurfactant from Thermophilic Bacterium Aneurinibacillus thermoaerophilus MK01 Newly Isolated from Municipal Landfill Site

A biosurfactant-producing thermophile was isolated from the Kahrizak landfill of Tehran and identified as a bacterium belonging to the genus Aneurinibacillus. A thermostable lipopeptide-type biosurfactant was purified from the culture medium of this bacterium and showed stability in the temperature range of 20–90 °C and pH range of 5–10. The produced biosurfactant could reduce the surface tension of water from 72 to 43 mN/m with a CMC of 1.21 mg/mL. The strain growing at a temperature of 45 °C produces a substantial amount of 5 g/L of biosurfactant in the medium supplemented with sunflower oil as the sole carbon source. Response surface methodology was employed to optimize the biosurfactant production using sunflower oil, sodium nitrate, and yeast extract as variables. The optimization resulted in 6.75 g/L biosurfactant production, i.e., 35 % improved as compared to the unoptimized condition. Thin-layer chromatography, FTIR spectroscopy, ¹H-NMR spectroscopy, and biochemical composition analysis confirmed the lipopeptide structure of the biosurfactant.     

Bioconversion of Sodium Dodecyl Sulphate to Rhamnolipid by Pseudomonas aeruginosa: A Novel and Cost-Effective Production Strategy

The utility of rhamnolipids in industry is currently limited due to the high constraints in its economic production. In this scenario, the novel utility of sodium dodecyl sulphate (SDS) as carbon source could serve as promising cost-effective strategy. Screening of effective SDS biodegraders led to the isolation of Pseudomonas aeruginosa S15 capable of concomitant SDS degradation and biosurfactant synthesis. SDS-based rhamnolipid production was proved on SDS minimal agar plates using cetyl trimethylammonium bromide–methylene blue method and optimised in SDS-based minimal salt (SBS) medium. SDS proved to be an ideal carbon source for rhamnolipid synthesis with a high substrate to product conversion rate yielding 6.9 g/l of rhamnolipids from 1 g/l SDS in 5 days. Fast atom bombardment mass spectroscopy analysis of the purified biosurfactant proved the presence of mono- and di-rhamnolipids, viz., Rha-C₁₀-C₁₀, Rha-C₁₀-C₁₂ and Rha-Rha-C₁₀-C₁₀ with surface active properties. The secreted rhamnolipids were not utilised by S15 as a carbon source, but it caused a dispersion of bacterial biofilms in SBS medium. To the best of our knowledge, this is the first report on bioconversion of synthetic detergent to biodetergent. This SDS-based novel methodology presents a more economised mode of rhamnolipid synthesis utilising SDS as sole carbon source.     

Enhanced Biodegradation of Alkane Hydrocarbons and Crude Oil by Mixed Strains and Bacterial Community Analysis

In this study, two strains, Acinetobacter sp. XM-02 and Pseudomonas sp. XM-01, were isolated from soil samples polluted by crude oil at Bohai offshore. The former one could degrade alkane hydrocarbons (crude oil and diesel, 1:4 (v/v)) and crude oil efficiently; the latter one failed to grow on alkane hydrocarbons but could produce rhamnolipid (a biosurfactant) with glycerol as sole carbon source. Compared with pure culture, mixed culture of the two strains showed higher capability in degrading alkane hydrocarbons and crude oil of which degradation rate were increased from 89.35 and 74.32?±?4.09 to 97.41 and 87.29?±?2.41 %, respectively. In the mixed culture, Acinetobacter sp. XM-02 grew fast with sufficient carbon source and produced intermediates which were subsequently utilized for the growth of Pseudomonas sp. XM-01 and then, rhamnolipid was produced by Pseudomonas sp. XM-01. Till the end of the process, Acinetobacter sp. XM-02 was inhibited by the rapid growth of Pseudomonas sp. XM-01. In addition, alkane hydrocarbon degradation rate of the mixed culture increased by 8.06 to 97.41 % compared with 87.29 % of the pure culture. The surface tension of medium dropping from 73.2?×?10^?3 to 28.6?×?10^?3 N/m. Based on newly found cooperation between the degrader and the coworking strain, rational investigations and optimal strategies to alkane hydrocarbons biodegradation were utilized for enhancing crude oil biodegradation.     

Adsorption and thermodynamics of biosurfactant,surfactin, monolayers at the air-buffered liquid interface

Adsorption of surfactin, a powerful lipopeptide biosurfactant, at the air-liquid interface has been investigated in this article. The adsorption took place from buffered solutions containing relatively high concentrations of surfactin co- and counterions. Dynamic surface tension measurements were used to follow the self-assembly of surfactin at the interface until equilibrium surface pressure Π ^e is reached at a given surfactin concentration (C _s). Gibbs adsorption equation in conjunction with the Langmuir adsorption isotherm was used to predict surfactin surface excess as a function of the biosurfactant concentration up to the critical micelle concentration (CMC). The predicted surface excess at saturation (Γ _∞ ) is 1.05?±?0.05 μmol m^?2, corresponding to an area per molecule (A _∞ ) of 159?±?8 Å². The adsorption equilibrium constant (K?=?(1.5?±?0.6)?×?10⁶ M^‐?1) was also estimated from the nonlinear regression of Π ^e???C _s data in region B of the Π ^e???ln?C _s plot. The value of K suggests that surfactin has strong affinity for the interface, which is in line with its known high surface activity. Gibbs elasticity (E _G) of the interfacial surfactin monolayers, which is an important thermodynamic property, was also predicted at different surfactin concentrations. The limiting value (at the CMC) of E _G was found to be 183 mN m^?1, which is comparable to those reported in the literature for similar systems. The findings reported in this work reveal that the surface tension measurements coupled with appropriate theoretical analysis could provide useful information comparable to those obtained using highly sophisticated techniques.     

Enhanced Biodegradation of Hydrocarbons in Soil by Microbial Biosurfactant, Sophorolipid

Effectiveness of a microbial biosurfactant, sophorolipid, was evaluated in washing and biodegradation of model hydrocarbons and crude oil in soil. Thirty percent of 2-methylnaphthalene was effectively washed and solubilized with 10 g/L of sophorolipid with similar or higher efficiency than that of commercial surfactants. Addition of sophorolipid in soil increased biodegradation of model compounds: 2-methylnaphthalene (95% degradation in 2 days), hexadecane (97%, 6 days), and pristane (85%, 6 days). Also, effective biodegradation method of crude oil in soil was observed by the addition of sophorolipid, resulting in 80% biodegradation of saturates and 72% aromatics in 8 weeks. These results showed the potentials of the microbial biosurfactant, sophorolipid, as an effective surfactant for soil washing and as an in situ biodegradation enhancer.     

Effects of ELF Magnetic Field in Combination with Iron(III) Chloride (FeCl3) on Cellular Growth and Surface Morphology of Escherichia coli (E. coli)

This study investigated the effects of extremely low frequency (ELF) magnetic field with/without iron(III) chloride (FeCl₃) on bacterial growth and morphology. The ELF exposures were carried out using a pair of Helmholtz coil-based ELF exposure system which was designed to generate 50 Hz sinusoidal magnetic field. The field was approximately uniform throughout the axis of the coil pair. The samples which were treated or non-treated with different concentrations FeCl₃ were exposed to 50 Hz, 2 millitesla (mT) magnetic field for 24 h. ELF effect on viability was assessed in terms of viable colony counts (in colony-forming unit per milliliter) with the standard plate count technique. Scanning electron microscopy was used to investigate the magnetic field effect on surface morphology of Escherichia coli. No significant results were seen in terms of cell viability between ELF and sham-exposed bacterial strains. Similarly, FeCl₃ treatment did not change cell viability of E. coli samples. However, we observed some morphological changes on E. coli cell surfaces. Pore formations and membrane destruction were seen on the surface of 24 h ELF field-exposed cells. We concluded that ELF magnetic field exposure at 2 mT does not affect cell viability; however, it may affect bacterial surface morphology.     

Lipopeptide surfactant production by Bacillus subtilis grown on low-cost raw materials

The production of biosurfactant by Bacillus subtilis ATCC 6633 was investigated using commercial sugar, sugarcane juice and cane molasses, sugarcane juice alcohol stillage, glycerol, mannitol, and soybean oil. Commercial sugar generated the minimum values of surface tension, with the best results (28.7 mN/m, (relative critical micelle concentration [CMC⁻¹] of 78.6) being achieved with 10 g of substrate/L in 48 h. At a pH between 7.0 and 8.0, a higher production of surface-active compounds and a greater emulsifier activity was also observed. Enrichment of the culture medium with trace minerals and EDTA showed maximum yields, whereas supplementation with yeast extract stimulated only cell growth. The kinetic studies revealed that biosurfactant production is a cell growth-associated process; surface tension, CMC, and emulsification index values of 29.6 dyn/cm, 82.3, and 57%, respectively, were achieved, thus indicating that it is feasible to produce biosurfactants from a renewable and low-cost carbon source.     

Candida Biofilm Disrupting Ability of Di-rhamnolipid (RL-2) Produced from Pseudomonas aeruginosa DSVP20

Biosurfactant produced from Pseudomonas aeruginosa DSVP20 was evaluated for its potential to disrupt Candida albicans biofilm formed on polystyrene (PS) surfaces in this investigation. P. aeruginosa DSVP20 exhibited optimum production of biosurfactant (5.8 g?L^?1) after 96 h of growth with an ability to reduce surface tension of the aqueous solution from 72 to 28 mN?m^?1. Analysis of purified biosurfactant with FT-IR, ¹H and ¹³C NMR and MALDI-TOF MS revealed it to be di-rhamnolipid (RL-2) in nature. Biofilm disrupting ability of RL-2 (0.16 mg?mL^?1) on Candida cells when checked using XTT reduction assay revealed that about 50 % of the cells remain adhered to 96-well plate after 2 h of treatment, while up to 90 % reduction in pre-formed C. albicans biofilm on PS surface was observed with RL-2 (5.0 mg?mL^?1) in a dose-dependent manner. Microscopic analyses (SEM and CLSM) further confirm the influence of RL-2 on disruption of Candida biofilm extracellular matrix on PS surface which can be exploited as a potential alternative to the available conventional therapies.     

Evaluation of waste products in the synthesis of surfactants by yeasts

The highest yields of biosurfactants were obtained by: (i) Pseudozyma antarctica (107.2 g L^?1) cultivated in a medium containing post-refining waste; (ii) Pseudozyma aphidis (77.7 g L^?1); and (iii) Starmerella bombicola (93.8 g L^?1) both cultivated in a medium with soapstock; (iv)Pichia jadinii (67.3 g L^?1) cultivated in a medium supplemented with waste frying oil. It was found that the biosurfactant synthesis yield increased in all strains when the cell surface hydrophobicity reached 70–80 %, enabling the microbial cells to make good contact with hydrophobic substrates. The lowest surface tension of the post-cultivation medium was from 32.0 mN m^?1 to 37.8 mN m^?1. However, this parameter (which was also determined by a drop collapse assay) was of limited use in monitoring biosurfactant synthesis in this study. The crude glycerol was not a good substrate for biosurfactant synthesis although, in the case of P. aphidis, 67.4 g L^?1 of biosurfactants were obtained after cultivation in the medium supplemented with glycerol fraction (GF2). In a low-cost medium containing soapstock and whey permeate or molasses, about 90 g L^?1 of mannosylerythritol lipids were synthesised by P. aphidis and approximately 40 g L^?1 by P. antarctica.     

Rhamnolipids Production by Multi-metal-Resistant and Plant-Growth-Promoting Rhizobacteria

The biosurfactant-producing Pseudomonas aeruginosa A11, with plant-growth-promoting (PGP) and multi-metal-resistant (MMR) features was isolated from the rhizosphere of a wild plant Parthenium hysterophorus. The strain A11 was able to utilize glycerol as a carbon source and produce 4,436.9 mg/L of biosurfactant after 120 h of incubation. The biosurfactants was characterized as rhamnolipids (RLs) by thin layer chromatography, Fourier transform infrared spectroscopy, nuclear magnetic resonance, and liquid chromatography–mass spectrometry analysis. Eight different RLs congeners were detected with RhaRhaC₁₀C₁₀ being most abundant. The purified rhamnolipid, dirhamnolipid, and monorhamnolipid reduced the surface tension of water to 29, 36, and 42 mN/m with critical micelle concentration of 83, 125, and 150 mg/L, respectively. The strain A11 demonstrated resistance against all the metals detected in rhizosphere except Hg and Ni. The strain A11 also possessed plant-growth-promoting features like siderophores, hydrogen cyanide, catalase, ammonia production, and phosphate solubilization. The dirhamnolipids formed crystals upon incubation at 4 °C, thus making separation of dirhamnolipids easy. Biosurfactant-producing ability along with MMR and PGP traits of the strain A11 makes it a potential candidate for application in the bacterial assisted enhancement of phytoremediation of heavy-metal-contaminated sites.     

Synthesis,Characterization, and Oil Recovery Application of Biosurfactant Produced by Indigenous <Emphasis Type="Italic">Pseudomonas aeruginosa</Emphasis> WJ-1 Using Waste Vegetable Oils

A bacterial strain was isolated and cultured from the oil excavation areas in tropical zone in northern China. The biochemical characteristics and partial sequenced 16S rRNA gene of isolate, WJ-1, was identical to those of cultured representatives of the species Pseudomonas aeruginosa. This bacterium was able to produce a type of biosurfactant. Compositional analysis revealed that the extracted biosurfactant was composed of high percentage lipid (∼74%, w/w) and carbohydrate (∼20%, w/w) in addition to a minor fraction of protein (∼6%, w/w). The best production of 50.2 g/l was obtained when the cells were grown on minimal salt medium containing 6.0% (w/v) glucose and 0.75% (w/v) sodium nitrate supplemented with 0.1% (v/v) element solution at 37 °C and 180 rpm after 96 h. The optimum biosurfactant production pH value was found to be 6.0–8.0. The biosurfactant of WJ-1, with the critical micelle concentration of 0.014 g/L, could reduce surface tension to 24.5 mN/m and emulsified kerosene up to EI₂₄ ≈95. The results obtained from time course study indicated that the surface tension reduction and emulsification potential was increased in the same way to cell growth. However, maximum biosurfactant production occurred and established in the stationary growth phase (after 90 h). Thin layer chromatography, Fourier transform infrared spectrum, and mass spectrum analysis indicate the extracted biosurfactant was affiliated with rhamnolipid. The core holder flooding experiments demonstrated that the oil recovery efficiency of strain and its biosurfactant was 23.02% residual oil.