Structural,magnetic and XPS studies of Sn0.95Co0.05O2-0.05 and Sn0.95Fe0.05O2-0.05 nanoparticles

Structural, microstructural, X-ray photoemission spectra (XPS) and magnetic properties of transition metal ion [5 mol% of Co (SC5) and Fe (SF5)]-doped SnO₂ nanoparticles have been studied. The SC5 and SF5 nanoparticles were synthesized by a chemical route using polyvinyl alcohol as surfactant. The doped SnO₂ crystallites were found to exhibit a tetragonal rutile structure and the average grains size was measured by the Scherer relation of X-ray diffraction. Transmission electron micrographs showed that the average grain size of SC5 is smaller than SF5. SC5 nanoparticles showed strong ferromagnetic behaviour but SF5 exhibited an F-centre exchange (FCE) mechanism. Temperature-dependent magnetization showed the values of phase transition temperature. XPS confirmed the presence of Sn–O–Co and Sn–O–Fe bonds in these SC5 and SF5 nanoparticles. The oxidation states of Sn, Co and Fe were found to be +4, +2 and +2, respectively, while the core level XPS peaks of Sn 3d, O 1s, Co 2p and Fe 2p were analyzed.     

White-light emission of ZnO nanoparticles prepared by sol-gel method

In:ZnO nanoparticles are prepared by the sol-gel process. The ratios of In/(Zn+In) are 0%, 5%, 8%, 10%, and 15%, respectively. Crystal phase structures and optoelectronic properties of these samples are characterized and the chromaticity coordinates of different samples are also calculated in CIE-XYZ colour system. The results show that preferred growth direction of ZnO changes from (002) plane to (001) plane and interplanar distance becomes shorter. When the doping amount of In is 5%, Zn atoms are completely replaced by In atoms. The resistivities of the samples first decrease, then increase afterwards with the increase of the amount of In. With the increase of In, the ultraviolet emission is redshifted and new peaks occur at 465 nm, 535 nm, and 630 nm. The sample with 10% indium has white-light emission. The band structures of samples with 0% and 12.5% indium are investigated by the first principle method. The mechanism of white emission is discussed from the viewpoint of additional energy levels.     

Electrical Properties of the Polycrystalline BiFe0.95Co0.05O3 Films

Physics of the Solid State - Semiconductor BiFe0.95Co0.05O3 thin-film compounds have been synthesized by a burst technique. The film surface morphology and the effect of electronic doping via...     

The study on the ZnO and Zn0.95Mn0.05O added YBCO system: Investigation of microstructure and transport properties

The effect of nano-size Zn_0.95Mn_0.05O and ZnO (30 nm) addition on the microstructure and the normal state transport properties of polycrystalline YBa₂Cu₃O_y (YBCO) was systematically studied. Samples were synthesized in air using a standard solid state reaction technique by adding nano-sized particles up to 10 wt.%. When Zn_0.95Mn_0.05O and ZnO are added to the YBCO the orthorhombic structure maintained even at the highest concentration. TEM and EDS analyses show the presence of inhomeginities embedded in the superconducting matrix. To interpret the normal state properties of the samples, the percolation theory based on localized states is applied. A cross-over between variable-range hopping and Coulomb gap mechanisms is observed as a result of increasing the nano-particles concentration. The ZnO addition modifies the electrical behavior of samples from metallic to insulating with a much lower concentration comparatively to Zn_0.95Mn_0.05O addition. The calculated values of the localization length, d, are greater in the case of Zn_0.95Mn_0.05O addition. This result can be interpreted by the internal structure defects.     

Characterization of ZnO:Co particles prepared by hydrothermal method for room temperature magnetism

ZnO based diluted magnetic semiconductor particles (ZnO:Co) have been grown using a hydrothermal method with good crystallinity. The atomic percentage of Co presented in the specimen is about 0.01. Based on the x-ray diffraction and high-resolution transition electron, Co is found to be incorporated into ZnO lattice without evidence of obvious Co precipitates. However, from photoluminescence (PL) spectra in the range of 1.94 -3.45 eV, a strong broad emission centered around 600 nm (2.07 eV) in the visible range as well as a relatively weak peak at 2.81 eV are observed, indicating the presence of Co impurities. Moreover, intrinsic emissions such as D^OX suggest that at least some Co have been doped into ZnO lattice, substituting for Zn²⁺ ions. The PL results further confirm the substitution of Zn²⁺ ions by Co, which leads to the changes of the electronic band structures. Magnetism could be realized at room temperature for the ZnO:Co nanoparticles under our experimental conditions although with low coercivity. The field-cooled and zero-field-cooled curves can be explained as a result of competition between the ferromagnetic and the antiferromagnetic ordering in the ZnO:Co nanoparticles. Combining the results from PL and magnetism characterization, it is reasonable to think that both doped Co in the ZnO lattice and Co impurities contribute to magnetism in ZnO:Co nanoparticles at room temperature.     

The structure and magnetic properties of Cu-doped ZnO prepared by sol-gel method

The Cu-doped ZnO and pure ZnO powders were synthesized by sol-gel method. The structural properties of the samples were investigated by X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and X-ray absorption spectroscopy. All the results confirmed that copper ions were well incorporated into the ZnO lattices by substituting Zn sites without changing the wurtzite structure and no secondary phase existed in Cu-doped ZnO nanoparticles. The Zn_0.97Cu_0.03O nanoparticles exhibited ferromagnetism at room temperature, as established by the vibrating sample magnetometer analysis.     

Spectral features and antibacterial properties of Cu-doped ZnO nanoparticles prepared by sol-gel method

Zn_(1-x)Cu_x O(x=0.00, 0.01, 0.03, and 0.05) nanoparticles are synthesized via the sol-gel technique using gelatin and nitrate precursors. The impact of copper concentration on the structural, optical, and antibacterial properties of these nanoparticles is demonstrated. Powder x-ray diffraction investigations have illustrated the organized Cu doping into ZnO nanoparticles up to Cu concentration of 5%(x = 0.05). However, the peak corresponding to CuO for x= 0.01 is not distinguishable. The images of field emission scanning electron microscopy demonstrate the existence of a nearly spherical shape with a size in the range of 30–52 nm. Doping Cu creates the Cu–O–Zn on the surface and results in a decrease in the crystallite size. Photoluminescence and absorption spectra display that doping Cu causes an increment in the energy band gap. The antibacterial activities of the nanoparticles are examined against Escherichia coli(Gram negative bacteria)cultures using optical density at 600 nm and a comparison of the size of inhibition zone diameter. It is found that both pure and doped ZnO nanoparticles indicate appropriate antibacterial activity which rises with Cu doping.     

Preparation of cytocompatible luminescent and magnetic nanohybrids based on ZnO, Zn0.95Ni0.05O and core@shell ZnO@Fe2O3 polymer grafted nanoparticles for biomedical imaging

ZnO, Zn_0.95Ni_0.05O and core@shell ZnO@??-Fe₂O₃ nanoparticles (NPs) have been prepared by forced hydrolysis in polyol medium and then coated via the ??grafting from?? approach with poly(sodium-4-styrenesulfonate) and poly(sodium-4-styrenesulfonate?Cco?Csodium methacrylate) in the case of ZnO. The surface-initiated atom transfer radical polymerization occurred from the surface-functionalized NPs with ??-bromoisobutyric acid as initiator. The polymer chains were grown from the surface to yield hybrid NPs with a 1?C3-nm thick organic shell. FT-IR, TGA and electron microscopy evidenced the presence of a polymer layer on the surface of NPs. Magnetic and optical properties of bare and coated NPs have been measured. Eventually, the weak cytotoxicity of coated NPs on human endothelial cell allows considering their potentialities as new tools for nanomedicine and biomedical imaging.     

Ultraviolet photoconductive detector based on Al doped ZnO films prepared by sol-gel method

We report a study on the fabrication and characterization of ultraviolet photodetectors based on ZnO:Al films. Using sol-gel technique, highly c-axis oriented ZnO films with 5 mol% Al doping were deposited on Si(1 1 1) substrates. The photoconductive UV detectors based on ZnO:Al thin films, having a metal-semiconductor-metal (MSM) structure with interdigital (IDT) configuration, were fabricated by using Au as a contact metal. The characteristics of dark and photocurrent of the UV detector and the UV photoresponse of the detector were investigated. The linear current-voltage (I-V) characteristics under both forward and reverse bias exhibit ohmic metal-semiconductor contacts. Under illumination using monochromatic light with a wavelength of 350 nm, photo-generated current was measured at 58.05 μA at a bias of 6 V. The detector exhibits an evident wide-range spectral responsivity and shows a trend similar to that in transmittance and photoluminescence spectrum.     

Microstructures, optical and electrical properties of In-doped ZnO thin films prepared by sol-gel method

ZnO and indium-doped ZnO (I_xZO) thin films were prepared on silica-glass substrates by the sol-gel method. The thin films were crystallized at 600 °C and 700 °C for 1 h in 6.9 × 10⁻¹ Torr under pure O₂ atmosphere. The analyzed results were compared to investigate the structural characteristics and optical properties. The surface morphology of the I_xZO films was different from that of the ZnO films, and showed a thin overlay structure. In addition, the crystallization of I_xZO film was depleted at higher crystallized temperatures. From XRD analysis, the ZnO and I_xZO thin films possessed hexagonal structures. Notably, micro-In₂O₃ phases were observed in the I_xZO thin films using EDS. Both of In₂O₃ phases and the crystallization mechanism not only improved the peeling of structure, but also improved the electrical conductivity of I_xZO thin films. For the PL spectrum, the optical property of the I_xZO film was raised at a higher crystallization temperature. Although the In₂O₃ phases reduced the structural defects of I_xZO thin film, the optical effect of the residual In³⁺ was not enhanced completely at higher crystallized temperatures.     

Structural and optical properties of ZnO thin films prepared by sol-gel method with different thickness

In this work, ZnO thin films with different thickness were prepared by sol-gel method on glass substrates and the structural and optical properties of these films were studied by X-ray diffractometer, atomic force microscope, UV-visible spectrophotometer, ellipsometer and fluorophotometer, respectively. The structural analyses show that all the samples have a wurtzite structure and are preferentially oriented along the c-axis perpendicular to the substrate surface. The growth process of highly c-axis oriented ZnO thin films derived from sol-gel method is a self-template process. With the increase of film thickness, the structural disorder decreases and the crystalline quality of the films is gradually improved. A transition of crystal growth mode from vertical growth to lateral growth is observed and the transition point is found between 270 and 360 nm thickness. The optical analyses show that with the increase of film thickness, both the refractive index and ultraviolet emission intensity are improved. However, the transmittance in the visible range is hardly influenced by the film thickness, and the averages are all above 80%.     

Structure and magnetic properties of Ni0.5Zn0.5Mn0.5-xMoxFe1.5O4 ferrites prepared by sol-gel auto-combustion method

A series of Mo doped Ni-Mn-Zn ferrites compounds with the formula Ni_0.5Zn_0.5Mn_0.5-xMo_xFe_1.5O₄ (x = 0, 0.025, 0.05, 0.075 and 0.1) were first synthesized by sol-gel auto-combustion method. The X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), and vibrating sample magnetometer (VSM) analysis were carried out to characterize the microstructural and magnetic properties of ferrites. Rietveld refinement of X-ray diffraction data confirmed the formation of cubic spinel structure and the emergence of FeMoO₄ phase with the substitution of Mo⁶⁺ contents. The grain size increased remarkably due to the formation of the liquid phase. The saturation magnetization (M_s) increased while the coercivity (H_c) decreased from 67.3 to 12.1 Oe due to the decrease of magneto-crystalline anisotropy constant. The initial permeability (μ_i) increased significantly from 34 (x = 0) to 114 (x = 0.075) and later decreased for x = 0.1. In our experiment, Ni_0.5Zn_0.5Mn_0.425Mo_0.075Fe_1.5O₄ ferrite presented the best microstructure and soft magnetic properties.     

Structural and cathodoluminiscent properties of Zr0.95Ce0.05O2 nanopowders prepared by sol-gel and template methods

Nanopowders of Zr_0.95Ce_0.05O₂ composition have been prepared by a standard Pechini-type sol-gel process and by means of a colloidal crystal template approach. In the latter method, inverse opal Zr_0.95Ce_0.05O₂ powders were fabricated employing poly(methyl methacrylate) (PMMA) colloidal crystals as a template. The effects of the two different synthesis routes on the structure and microstructural characteristics of the prepared nanopowders were evaluated by X-ray diffraction and scanning electron microscopy. For both preparation routes, the X-ray diffraction analysis has shown that a tetragonal fluorite structure is formed with a crystallite size of ∼35-40 nm. The scanning electron microscopy measurements indicate that the powder obtained by the sol-gel Pechini-type process is comprised of nanoparticles that are arranged in agglomerates with shape and size relatively uniform whereas the inverse opal Zr_0.95Ce_0.05O₂ nanopowders exhibit the formation of macropores with a mean size of ∼100 nm. The cathodoluminescence spectra of the prepared Zr_0.95Ce_0.05O₂ nanomaterials have been measured in the 300-800 nm wavelength range. The powder prepared by sol-gel method yields a broad emission band centered at 482 nm whereas the emission from the inverse opal preparation is considerably less intense.     

衬底温度对PLD法生长的Mg0.05Zn0.95O薄膜结构和发光特性的影响

用脉冲激光沉积(PLD)法在不同温度的Si(111衬底上成功制备了c轴择优取向的Mg0.05Zn0.95O薄膜.通过X射线衍射(XRD)和光致发光谱(PL)研究了衬底温度对Mg0.05Zn0.95O薄膜结构和发光特性的影响,探讨了膜的结晶质量与发光特性之间的关系.结果表明,在衬底温度为450℃时生长的Mg0.05Zn0.95O薄膜具有很好的轴取向和较强的光致发光峰.室温下分别用激发波长为240,300和325nm的氙灯作为激发光源得到不同样品的PL谱,分析表明紫外发光峰和紫峰来源于自由激子的复合辐射且发光强度与薄膜的结晶质量密切相关,蓝绿发光峰与氧空位有关.此外,探讨了衬底温度影响紫外光致发光峰红移和蓝移的可能机理.     

退火对ZnO:Al薄膜光致发光性能的影响

采用溶胶-凝胶工艺在石英衬底上制备ZnO:Al（AZO）薄膜,通过不同温度的退火处理,研究了退火对AZO薄膜结构和光致发光特性的影响。XRD图谱表明：所制备的薄膜具有c轴高度择优取向,随着退火温度的升高,(002)峰的强度逐渐增强,同时(002)峰的半高宽逐渐减小,表明晶粒在不断增大。未退火样品的光致发光（PL）谱由361 nm附近的紫外带边发射峰和500 nm附近的深能级发射峰组成。样品经退火后,以500 nm为中心的绿带发射逐渐减弱,而带边发射强度有所增强,并且逐渐红移到366 nm附近,与吸收边移动的测试结果相吻合。对经过不同时间退火的样品分析表明,AZO薄膜的发光特性与退火时间也有很大关系,时间过短可见波段的发射较强,但时间过长会使晶粒发生团聚,导致紫外发射峰强度减弱。     

Effect of annealing temperature on photocatalytic activity of ZnO thin films prepared by sol-gel method

Zinc oxide thin films are deposited on Si and quartz substrates using the sol-gel method. The thin films, annealed at 400, 600 and 800 °C respectively, are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), ultraviolet-visible spectrophotometer (UV-Vis), fluorescence spectrometer (FL) and the photocatalytic activity is tested by the decomposition of methyl orange dye under UV illumination. The results show that the mean grain size, surface-to-volume ratio, rms roughness and degradation efficiency of the thin films increases with increasing annealing temperature. In particular, ZnO thin film annealed at 800 °C exhibits the highest photocatalytic activity, degrading methyl orange by almost 88% in 180 min. Photocatalytic reaction mechanism of the ZnO thin films is discussed in detail, and the oxygen defects are proposed to be the active sites of the ZnO photocatalyst.     

Influences of Al doping concentration on structural,electrical and optical properties of Zn0.95Ni0.05O powders

Nanocrystalline Zn_0.95−xNi_0.05Al_xO (x = 0.01, 0.02, 0.05 and 0.10) diluted magnetic semiconductors have been synthesized by an auto-combustion method. X-ray diffraction measurements indicate that all Al-doped Zn_0.95Ni_0.05O samples have the pure wurtzite structure. Transmission electron microscope analyses show that the as-synthesized powders are of the size 40–45 nm. High-resolution transmission electron microscope, energy dispersive spectrometer and X-ray photoemission spectroscope analyses indicate that Ni²⁺ and Al³⁺ uniformly substitute Zn²⁺ in the wurtzite structure without forming any secondary phases. The Al doping concentration dependences of cell parameters (a and c), resistance and the ratio of green emission to UV emission have the similar trends.     

退火对ZnO:Al薄膜光致发光性能的影响

 采用溶胶-凝胶工艺在石英衬底上制备ZnO:Al（AZO）薄膜,通过不同温度的退火处理,研究了退火对AZO薄膜结构和光致发光特性的影响。XRD图谱表明：所制备的薄膜具有c轴高度择优取向,随着退火温度的升高,(002)峰的强度逐渐增强,同时(002)峰的半高宽逐渐减小,表明晶粒在不断增大。未退火样品的光致发光（PL）谱由361 nm附近的紫外带边发射峰和500 nm附近的深能级发射峰组成。样品经退火后,以500 nm为中心的绿带发射逐渐减弱,而带边发射强度有所增强,并且逐渐红移到366 nm附近,与吸收边移动的测试结果相吻合。对经过不同时间退火的样品分析表明,AZO薄膜的发光特性与退火时间也有很大关系,时间过短可见波段的发射较强,但时间过长会使晶粒发生团聚,导致紫外发射峰强度减弱。     

Effect of Zn substitution on the electrical properties of Bi2Co0.1V0.9O5.35 synthesized by sol-gel method

Samples of Bi₂V_0.9Co_0.1-xZn_xO_5.35, 0.02 ≤ x ≤ 0.08 with layered Aurivillius structure were synthesized successfully by sol-gel citrate method. Structural and electrical characterization of compositions has been investigated by X-ray diffraction, thermogravimetric analysis–differential scanning calorimetric (TGA–DSC) analysis and AC impedance spectroscopy. The tetragonal γ phase has been observed for all investigated samples. The AC impedance response of samples has been measured in the frequency range of 20 Hz to 1 MHz. The impedance for pellets decreases as thermal energy increases. The contribution of grain to the conduction process is more than that of grain boundary. The ionic conductivity and dielectric permittivity are found to be composition-dependent and increase with increasing Zn concentration. The maximum electrical conductivity observed for the composition x = 0.08 is σ = 4.51 × 10^?4 S cm^?1 at 300 °C.     

Effect of aging time of ZnO sol on the structural and optical properties of ZnO thin films prepared by sol-gel method

In this work, ZnO thin films were prepared by sol-gel method and the effect of aging time of ZnO sol on the structural and optical properties of the films was studied. The structural characteristics of the samples were analyzed by an atomic force microscope and an X-ray diffractometer. The optical properties were studied by a UV-vis spectrophotometer and a fluorophotometer. The results show that the ZnO thin film prepared by the as-synthesized ZnO sol had relatively poor crystalline quality, low optical transmittance in the visible range and relatively weak ultraviolet emission performance. After the as-synthesized ZnO sol was aged for 24 h, the degree of the preferred crystal orientation along the c-axis of the ZnO thin film prepared by this aged sol was improved. At the same time, this film had a very smooth surface with uniform grains and both its visible range transmittance and ultraviolet emission intensity were obviously increased. These results suggest that appropriate aging of ZnO sol is very important for the improvement of structural and optical quality of ZnO thin films derived from sol-gel method.